1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
|
/* Copyright 2020 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Volteer board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Baseboard features */
#include "baseboard.h"
/* Optional features */
#define CONFIG_SYSTEM_UNLOCKED /* Allow dangerous commands while in dev. */
#define CONFIG_POWER_BUTTON
#undef CONFIG_UART_TX_BUF_SIZE
#define CONFIG_UART_TX_BUF_SIZE 4096
/* LED defines */
#define CONFIG_LED_POWER_LED
#define CONFIG_LED_ONOFF_STATES
/* Keyboard features */
/* Sensors */
#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
#define CONFIG_ACCEL_LIS2DE /* Lid accel */
#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */
/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK \
BIT(LID_ACCEL)
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
/* USB Type C and USB PD defines */
/*
* USB-C port's USB2 & USB3 mapping from schematics
* USB2 numbering on PCH - 1 to n
* USB3 numbering on AP - 0 to n (PMC's USB3 numbering for MUX
* configuration is - 1 to n hence add +1)
*/
#define USBC_PORT_0_USB2_NUM 9
#define USBC_PORT_0_USB3_NUM 1
#define USBC_PORT_1_USB2_NUM 4
#define USBC_PORT_1_USB3_NUM 2
/* USB Type A Features */
/* BC 1.2 */
/* Volume Button feature */
/* Fan features */
/*
* Macros for GPIO signals used in common code that don't match the
* schematic names. Signal names in gpio.inc match the schematic and are
* then redefined here to so it's more clear which signal is being used for
* which purpose.
*/
#define GPIO_AC_PRESENT GPIO_ACOK_OD
#define GPIO_EC_INT_L GPIO_EC_PCH_INT_ODL
#define GPIO_EN_PP5000 GPIO_EN_PP5000_A
#define GPIO_ENTERING_RW GPIO_EC_ENTERING_RW
#define GPIO_LID_OPEN GPIO_EC_LID_OPEN
#define GPIO_KBD_KSO2 GPIO_EC_KSO_02_INV
#define GPIO_PCH_WAKE_L GPIO_EC_PCH_WAKE_ODL
#define GPIO_PCH_PWRBTN_L GPIO_EC_PCH_PWR_BTN_ODL
#define GPIO_PCH_RSMRST_L GPIO_EC_PCH_RSMRST_ODL
#define GPIO_PCH_RTCRST GPIO_EC_PCH_RTCRST
#define GPIO_PCH_SYS_PWROK GPIO_EC_PCH_SYS_PWROK
#define GPIO_PCH_SLP_S0_L GPIO_SLP_S0_L
#define GPIO_PCH_SLP_S3_L GPIO_SLP_S3_L
#define GPIO_PG_EC_DSW_PWROK GPIO_DSW_PWROK
#define GPIO_POWER_BUTTON_L GPIO_H1_EC_PWR_BTN_ODL
#define GPIO_RSMRST_L_PGOOD GPIO_PG_EC_RSMRST_ODL
#define GPIO_CPU_PROCHOT GPIO_EC_PROCHOT_ODL
#define GPIO_SYS_RESET_L GPIO_SYS_RST_ODL
#define GPIO_WP_L GPIO_EC_WP_L
#define GPIO_USB_C1_BC12_INT_ODL GPIO_USB_C1_MIX_INT_ODL
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
#define GMR_TABLET_MODE_GPIO_L GPIO_TABLET_MODE_L
/* I2C Bus Configuration */
#define CONFIG_I2C
#define I2C_PORT_SENSOR NPCX_I2C_PORT0_0
#define I2C_PORT_USB_C0 NPCX_I2C_PORT1_0
#define I2C_PORT_USB_C1 NPCX_I2C_PORT2_0
#define I2C_PORT_USB_1_MIX NPCX_I2C_PORT3_0
#define I2C_PORT_POWER NPCX_I2C_PORT5_0
#define I2C_PORT_EEPROM NPCX_I2C_PORT7_0
#define I2C_PORT_BATTERY I2C_PORT_POWER
#define I2C_PORT_CHARGER I2C_PORT_EEPROM
#define I2C_ADDR_EEPROM_FLAGS 0x50
#define CONFIG_I2C_MASTER
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum battery_type {
BATTERY_SMP,
BATTERY_LGC,
BATTERY_SUNWODA,
BATTERY_TYPE_COUNT,
};
enum pwm_channel {
PWM_CH_LED4_SIDESEL = 0,
PWM_CH_FAN,
PWM_CH_KBLIGHT,
PWM_CH_COUNT
};
enum sensor_id {
LID_ACCEL = 0,
BASE_ACCEL,
BASE_GYRO,
VSYNC,
SENSOR_COUNT,
};
/* TODO: b/143375057 - Remove this code after power on. */
void c10_gate_change(enum gpio_signal signal);
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|