1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
|
/* Copyright (c) 2013 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* McCroskey board-specific configuration */
#include "chipset.h"
#include "common.h"
#include "console.h"
#include "gpio.h"
#include "hooks.h"
#include "i2c.h"
#include "keyboard_raw.h"
#include "registers.h"
#include "spi.h"
#include "task.h"
#include "timer.h"
#include "util.h"
#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP | GPIO_INT_BOTH)
#define GPIO_KB_OUTPUT (GPIO_OUTPUT | GPIO_OPEN_DRAIN | GPIO_OUT_LOW)
#define HARD_RESET_TIMEOUT_MS 5
static void kbd_power_on(enum gpio_signal signal);
/* GPIO signal list. Must match order from enum gpio_signal. */
const struct gpio_info gpio_list[] = {
/* Inputs with interrupt handlers are first for efficiency */
{"KB_IN00", GPIO_B, (1<<8), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KB_IN01", GPIO_B, (1<<9), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KB_IN02", GPIO_B, (1<<10), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KB_IN03", GPIO_B, (1<<11), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KB_IN04", GPIO_B, (1<<12), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KB_IN05", GPIO_B, (1<<13), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KB_IN06", GPIO_B, (1<<14), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KB_IN07", GPIO_B, (1<<15), GPIO_KB_INPUT,
keyboard_raw_gpio_interrupt},
{"KBD_PWR_BUTTON", GPIO_B, (1<<2), GPIO_INPUT, kbd_power_on},
{"OMZO_RDY_L", GPIO_A, (1<<0), GPIO_INPUT, NULL}, /* PA0_WKUP */
{"OZMO_RST_L", GPIO_A, (1<<2), GPIO_ODR_HIGH, NULL},
{"VBUS_UP_DET", GPIO_A, (1<<3), GPIO_INPUT, NULL},
{"OZMO_REQ_L", GPIO_A, (1<<8), GPIO_INPUT, NULL},
{"CHARGE_ZERO", GPIO_B, (1<<0), GPIO_INPUT, NULL},
{"CHARGE_SHUNT", GPIO_B, (1<<1), GPIO_INPUT, NULL},
{"PMIC_INT_L", GPIO_B, (1<<5), GPIO_INPUT, NULL},
/*
* I2C pins should be configured as inputs until I2C module is
* initialized. This will avoid driving the lines unintentionally.
*/
{"I2C1_SCL", GPIO_B, (1<<6), GPIO_INPUT, NULL},
{"I2C1_SDA", GPIO_B, (1<<7), GPIO_INPUT, NULL},
{"KB_OUT00", GPIO_C, (1<<0), GPIO_KB_OUTPUT, NULL},
{"KB_OUT01", GPIO_C, (1<<1), GPIO_KB_OUTPUT, NULL},
{"KB_OUT02", GPIO_C, (1<<2), GPIO_KB_OUTPUT, NULL},
{"KB_OUT03", GPIO_C, (1<<3), GPIO_KB_OUTPUT, NULL},
{"KB_OUT04", GPIO_C, (1<<4), GPIO_KB_OUTPUT, NULL},
{"KB_OUT05", GPIO_C, (1<<5), GPIO_KB_OUTPUT, NULL},
{"KB_OUT06", GPIO_C, (1<<6), GPIO_KB_OUTPUT, NULL},
{"KB_OUT07", GPIO_C, (1<<7), GPIO_KB_OUTPUT, NULL},
{"KB_OUT08", GPIO_C, (1<<8), GPIO_KB_OUTPUT, NULL},
{"KB_OUT09", GPIO_C, (1<<9), GPIO_KB_OUTPUT, NULL},
{"KB_OUT10", GPIO_C, (1<<10), GPIO_KB_OUTPUT, NULL},
{"KB_OUT11", GPIO_C, (1<<11), GPIO_KB_OUTPUT, NULL},
{"KB_OUT12", GPIO_C, (1<<12), GPIO_KB_OUTPUT, NULL},
{"USB_VBUS_CTRL", GPIO_C, (1<<13), GPIO_OUT_LOW, NULL},
{"HUB_RESET", GPIO_C, (1<<14), GPIO_ODR_HIGH, NULL},
{"WP_L", GPIO_D, (1<<2), GPIO_INPUT, NULL},
/* FIXME: make this alt. function */
{"BL_PWM", GPIO_A, (1<<1), GPIO_OUTPUT, NULL},
/* Unimplemented signals which we need to emulate for now */
GPIO_SIGNAL_NOT_IMPLEMENTED("EC_INT"),
GPIO_SIGNAL_NOT_IMPLEMENTED("ENTERING_RW"),
#if 0
/* Other GPIOs (probably need to be set up below as alt. function) */
{"STM_USBDM", GPIO_A, (1<<11), GPIO_DEFAULT, NULL},
{"STM_USBDP", GPIO_A, (1<<12), GPIO_DEFAULT, NULL},
{"JTMS_SWDIO", GPIO_A, (1<<13), GPIO_DEFAULT, NULL},
{"JTCK_SWCLK", GPIO_A, (1<<14), GPIO_DEFAULT, NULL},
{"JTDI", GPIO_A, (1<<15), GPIO_DEFAULT, NULL},
{"JTDO", GPIO_B, (1<<3), GPIO_DEFAULT, NULL},
{"JNTRST", GPIO_B, (1<<4), GPIO_DEFAULT, NULL},
{"OSC32_OUT", GPIO_C, (1<<15), GPIO_DEFAULT, NULL},
#endif
};
BUILD_ASSERT(ARRAY_SIZE(gpio_list) == GPIO_COUNT);
void board_config_pre_init(void)
{
uint32_t val;
/* Enable all GPIOs clocks
* TODO: more fine-grained enabling for power saving
*/
STM32_RCC_APB2ENR |= 0x1fd;
#ifdef CONFIG_SPI
/* SPI1 on pins PA4-7 (alt. function push-pull, 10MHz) */
/* FIXME: Connected device SPI freq is fxo/2 in master mode, fxo/4
* in slave mode. fxo ranges from 12-40MHz */
val = STM32_GPIO_CRL(GPIO_A) & ~0xffff0000;
val |= 0x99990000;
STM32_GPIO_CRL(GPIO_A) = val;
#endif
/* remap OSC_IN/OSC_OUT to PD0/PD1 */
STM32_GPIO_AFIO_MAPR |= 1 << 15;
/* use PB3 as a GPIO, so disable JTAG and keep only SWD */
STM32_GPIO_AFIO_MAPR = (STM32_GPIO_AFIO_MAPR & ~(0x7 << 24))
| (2 << 24);
/* remap TIM2_CH2 to PB3 */
STM32_GPIO_AFIO_MAPR = (STM32_GPIO_AFIO_MAPR & ~(0x3 << 8))
| (1 << 8);
/*
* Set alternate function for USART1. For alt. function input
* the port is configured in either floating or pull-up/down
* input mode (ref. section 7.1.4 in datasheet RM0041):
* PA9: Tx, alt. function output
* PA10: Rx, input with pull-down
*
* note: see crosbug.com/p/12223 for more info
*/
val = STM32_GPIO_CRH(GPIO_A) & ~0x00000ff0;
val |= 0x00000890;
STM32_GPIO_CRH(GPIO_A) = val;
}
/* GPIO configuration to be done after I2C module init */
void board_i2c_post_init(int port)
{
uint32_t val;
/* enable alt. function (open-drain) */
if (port == STM32_I2C1_PORT) {
/* I2C1 is on PB6-7 */
val = STM32_GPIO_CRL(GPIO_B) & ~0xff000000;
val |= 0xdd000000;
STM32_GPIO_CRL(GPIO_B) = val;
}
}
void chipset_reset(int is_cold)
{
/* FIXME: this is just a stub for now... */
}
void kbd_power_on(enum gpio_signal signal)
{
/* FIXME: this is just a stub for now... */
}
|