1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
|
/* Copyright 2017 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
#include "atomic.h"
#include "extpower.h"
#include "charge_manager.h"
#include "common.h"
#include "console.h"
#include "driver/tcpm/ps8xxx.h"
#include "gpio.h"
#include "hooks.h"
#include "host_command.h"
#include "registers.h"
#include "system.h"
#include "task.h"
#include "timer.h"
#include "util.h"
#include "usb_mux.h"
#include "usb_pd.h"
#include "usb_pd_tcpm.h"
#define CPRINTF(format, args...) cprintf(CC_USBPD, format, ## args)
#define CPRINTS(format, args...) cprints(CC_USBPD, format, ## args)
static uint8_t vbus_en[CONFIG_USB_PD_PORT_MAX_COUNT];
static uint8_t vbus_rp[CONFIG_USB_PD_PORT_MAX_COUNT] = {TYPEC_RP_1A5,
TYPEC_RP_1A5};
int board_vbus_source_enabled(int port)
{
return vbus_en[port];
}
static void board_vbus_update_source_current(int port)
{
enum gpio_signal gpio_5v_en = port ? GPIO_USB_C1_5V_EN :
GPIO_USB_C0_5V_EN;
enum gpio_signal gpio_3a_en = port ? GPIO_USB_C1_3A_EN :
GPIO_USB_C0_3A_EN;
if (system_get_board_version() >= 1) {
/*
* For rev1 and beyond, 1.5 vs 3.0 A limit is controlled by a
* dedicated gpio where high = 3.0A and low = 1.5A. VBUS on/off
* is controlled by GPIO_USB_C0/1_5V_EN. Both of these signals
* can remain outputs.
*/
gpio_set_level(gpio_3a_en, vbus_rp[port] == TYPEC_RP_3A0 ?
1 : 0);
gpio_set_level(gpio_5v_en, vbus_en[port]);
} else {
/*
* Driving USB_Cx_5V_EN high, actually put a 16.5k resistance
* (2x 33k in parallel) on the NX5P3290 load switch ILIM pin,
* setting a minimum OCP current of 3186 mA.
* Putting an internal pull-up on USB_Cx_5V_EN, effectively put
* a 33k resistor on ILIM, setting a minimum OCP current of
* 1505 mA.
*/
int flags = (vbus_rp[port] == TYPEC_RP_1A5 && vbus_en[port]) ?
(GPIO_INPUT | GPIO_PULL_UP) :
(GPIO_OUTPUT | GPIO_PULL_UP);
gpio_set_level(gpio_5v_en, vbus_en[port]);
gpio_set_flags(gpio_5v_en, flags);
}
}
__override void typec_set_source_current_limit(int port, enum tcpc_rp_value rp)
{
vbus_rp[port] = rp;
/* change the GPIO driving the load switch if needed */
board_vbus_update_source_current(port);
}
int pd_set_power_supply_ready(int port)
{
/* Disable charging */
gpio_set_level(port ? GPIO_USB_C1_CHARGE_L :
GPIO_USB_C0_CHARGE_L, 1);
/* Ensure we advertise the proper available current quota */
charge_manager_source_port(port, 1);
/* Provide VBUS */
vbus_en[port] = 1;
board_vbus_update_source_current(port);
if (system_get_board_version() >= 2)
pd_set_vbus_discharge(port, 0);
/* notify host of power info change */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
return EC_SUCCESS; /* we are ready */
}
void pd_power_supply_reset(int port)
{
int prev_en;
prev_en = vbus_en[port];
/* Disable VBUS */
vbus_en[port] = 0;
board_vbus_update_source_current(port);
/* Enable discharge if we were previously sourcing 5V */
if (system_get_board_version() >= 2 && prev_en)
pd_set_vbus_discharge(port, 1);
/* Give back the current quota we are no longer using */
charge_manager_source_port(port, 0);
/* notify host of power info change */
pd_send_host_event(PD_EVENT_POWER_CHANGE);
}
int pd_snk_is_vbus_provided(int port)
{
return !gpio_get_level(port ? GPIO_USB_C1_VBUS_WAKE_L :
GPIO_USB_C0_VBUS_WAKE_L);
}
int pd_check_vconn_swap(int port)
{
/* in G3, do not allow vconn swap since pp5000_A rail is off */
return gpio_get_level(GPIO_PMIC_SLP_SUS_L);
}
__override void pd_execute_data_swap(int port, int data_role)
{
/* Only port 0 supports device mode. */
if (port != 0)
return;
gpio_set_level(GPIO_USB2_OTG_ID,
(data_role == PD_ROLE_UFP) ? 1 : 0);
gpio_set_level(GPIO_USB2_OTG_VBUSSENSE,
(data_role == PD_ROLE_UFP) ? 1 : 0);
}
|