blob: 9c5454ef2135481b2240f8adb96ee9f537068275 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
|
/* Copyright 2021 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
#include "common.h"
#include "console.h"
#include "fpsensor_detect.h"
#include "gpio.h"
#include "hooks.h"
#include "registers.h"
#include "spi.h"
#include "system.h"
#include "task.h"
#include "util.h"
#include "board_rw.h"
#ifndef SECTION_IS_RW
#error "This file should only be built for RW."
#endif
/* SPI devices */
const struct spi_device_t spi_devices[] = {
/* Fingerprint sensor (SCLK at 4Mhz) */
{ .port = CONFIG_SPI_FP_PORT, .div = 3, .gpio_cs = GPIO_SPI4_NSS }
};
const unsigned int spi_devices_used = ARRAY_SIZE(spi_devices);
/* Allow changing the signal used for S3 sleep depending on the board being
* used: http://b/179946521.
*/
static int gpio_slp_s3_l = GPIO_PCH_SLP_S3_L;
static void ap_deferred(void)
{
/*
* in S3: SLP_S3_L is 0 and SLP_S0_L is X.
* in S0ix: SLP_S3_L is X and SLP_S0_L is 0.
* in S0: SLP_S3_L is 1 and SLP_S0_L is 1.
* in S5/G3, the FP MCU should not be running.
*/
int running = gpio_get_level(gpio_slp_s3_l) &&
gpio_get_level(GPIO_PCH_SLP_S0_L);
if (running) { /* S0 */
disable_sleep(SLEEP_MASK_AP_RUN);
hook_notify(HOOK_CHIPSET_RESUME);
} else { /* S0ix/S3 */
hook_notify(HOOK_CHIPSET_SUSPEND);
enable_sleep(SLEEP_MASK_AP_RUN);
}
}
DECLARE_DEFERRED(ap_deferred);
/* PCH power state changes */
void slp_event(enum gpio_signal signal)
{
hook_call_deferred(&ap_deferred_data, 0);
}
static void spi_configure(void)
{
gpio_config_module(MODULE_SPI_MASTER, 1);
/* Set all SPI master signal pins to very high speed: pins E2/4/5/6 */
STM32_GPIO_OSPEEDR(GPIO_E) |= 0x00003f30;
/* Enable clocks to SPI4 module (master) */
STM32_RCC_APB2ENR |= STM32_RCC_PB2_SPI4;
spi_enable(&spi_devices[0], 1);
}
void board_init_rw(void)
{
enum fp_sensor_spi_select spi_select = get_fp_sensor_spi_select();
ccprints("FP_SPI_SEL: %s", fp_sensor_spi_select_to_str(spi_select));
spi_configure();
ccprints("TRANSPORT_SEL: %s",
fp_transport_type_to_str(get_fp_transport_type()));
/* Use SPI select as a proxy for running on the icetower dev board. */
if (spi_select == FP_SENSOR_SPI_SELECT_DEVELOPMENT)
gpio_slp_s3_l = GPIO_PCH_SLP_S3_L_ALT;
/* Enable interrupt on PCH power signals */
gpio_enable_interrupt(gpio_slp_s3_l);
gpio_enable_interrupt(GPIO_PCH_SLP_S0_L);
/* enable the SPI slave interface if the PCH is up */
hook_call_deferred(&ap_deferred_data, 0);
}
|