1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
|
/* Copyright 2015 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Oak board configuration */
#include "battery.h"
#include "charger.h"
#include "chipset.h"
#include "common.h"
#include "console.h"
#include "extpower.h"
#include "gpio.h"
#include "hooks.h"
#include "host_command.h"
#include "i2c.h"
#include "keyboard_raw.h"
#include "lid_switch.h"
#include "power.h"
#include "power_button.h"
#include "registers.h"
#include "spi.h"
#include "switch.h"
#include "task.h"
#include "timer.h"
#include "util.h"
#define CPRINTS(format, args...) cprints(CC_USBCHARGE, format, ## args)
#define CPRINTF(format, args...) cprintf(CC_USBCHARGE, format, ## args)
#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP | GPIO_INT_BOTH)
#define GPIO_KB_OUTPUT GPIO_ODR_HIGH
static void ap_reset_deferred(void)
{
/* Warm reset AP */
chipset_reset(0);
}
DECLARE_DEFERRED(ap_reset_deferred);
void ap_reset_interrupt(enum gpio_signal signal)
{
if (gpio_get_level(GPIO_AP_RESET_L) == 0)
hook_call_deferred(ap_reset_deferred, 0);
}
void vbus_wake_interrupt(enum gpio_signal signal)
{
CPRINTF("VBUS %d\n", gpio_get_level(signal));
}
void pd_mcu_interrupt(enum gpio_signal signal)
{
CPRINTF("PD INT\n");
}
#include "gpio_list.h"
/* power signal list. Must match order of enum power_signal. */
const struct power_signal_info power_signal_list[] = {
{GPIO_SOC_POWER_GOOD, 1, "POWER_GOOD"}, /* Active high */
{GPIO_SUSPEND_L, 0, "SUSPEND#_ASSERTED"}, /* Active low */
};
BUILD_ASSERT(ARRAY_SIZE(power_signal_list) == POWER_SIGNAL_COUNT);
/* I2C ports */
const struct i2c_port_t i2c_ports[] = {
{"battery", I2C_PORT_BATTERY, 100, GPIO_I2C0_SCL, GPIO_I2C0_SDA},
{"pd", I2C_PORT_PD_MCU, 1000, GPIO_I2C1_SCL, GPIO_I2C1_SDA}
};
const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
static int discharging_on_ac;
/**
* Discharge battery when on AC power for factory test.
*/
int board_discharge_on_ac(int enable)
{
int rv = charger_discharge_on_ac(enable);
if (rv == EC_SUCCESS)
discharging_on_ac = enable;
return rv;
}
/**
* Reset PD MCU
*/
void board_reset_pd_mcu(void)
{
gpio_set_level(GPIO_USB_PD_RST_L, 0);
usleep(100);
gpio_set_level(GPIO_USB_PD_RST_L, 1);
}
void __board_i2c_set_timeout(int port, uint32_t timeout)
{
}
void i2c_set_timeout(int port, uint32_t timeout)
__attribute__((weak, alias("__board_i2c_set_timeout")));
/* Initialize board. */
static void board_init(void)
{
/* Enable rev1 testing GPIOs */
gpio_set_level(GPIO_SYSTEM_POWER_H, 1);
/* Enable PD MCU interrupt */
gpio_enable_interrupt(GPIO_PD_MCU_INT);
/* Enable VBUS interrupt */
gpio_enable_interrupt(GPIO_VBUS_WAKE_L);
#ifdef CONFIG_AP_WARM_RESET_INTERRUPT
gpio_enable_interrupt(GPIO_AP_RESET_L);
#endif
}
DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
#ifndef CONFIG_AP_WARM_RESET_INTERRUPT
/* Using this hook if system doesn't have enough external line. */
static void check_ap_reset_second(void)
{
/* Check the warm reset signal from servo board */
static int warm_reset, last;
warm_reset = !gpio_get_level(GPIO_AP_RESET_L);
if (last == warm_reset)
return;
if (warm_reset)
chipset_reset(0); /* Warm reset AP */
last = warm_reset;
}
DECLARE_HOOK(HOOK_SECOND, check_ap_reset_second, HOOK_PRIO_DEFAULT);
#endif
|
