1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
|
/* Copyright 2018 The ChromiumOS Authors
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Phaser board configuration */
#ifndef __CROS_EC_BOARD_H
#define __CROS_EC_BOARD_H
/* Select Baseboard features */
#define VARIANT_OCTOPUS_EC_NPCX796FB
#define VARIANT_OCTOPUS_CHARGER_ISL9238
#include "baseboard.h"
/* b/203442963
* It's workaround to reduce keyboard's "Silver Migration".
* From keyboard vendor's feedback, there are two factors to cause
* "Silver Migration".
* 1. A voltage potential between trace.
* 2. The presence of an electrolyte , such as moisture.
* The reason cause voltage potential between KSIxx trace is EC enter ec
* hibernate PSL and turn EC's VCC1 power off. Besides KSI2, the other
* KSIxx will be turn off. KSI2 is powered by H1.
* To avoid voltage potential is keep KSIxx on. That means not to enter
* ec hibernate PSL.
*/
#undef CONFIG_HIBERNATE_PSL
#define GPIO_PG_EC_RSMRST_ODL GPIO_RSMRST_L_PGOOD
#define CONFIG_VOLUME_BUTTONS
#define GPIO_VOLUME_UP_L GPIO_EC_VOLUP_BTN_ODL
#define GPIO_VOLUME_DOWN_L GPIO_EC_VOLDN_BTN_ODL
#define CONFIG_LED_COMMON
#define CONFIG_TEMP_SENSOR
#define CONFIG_THERMISTOR
#define CONFIG_STEINHART_HART_3V3_13K7_47K_4050B
#define CONFIG_STEINHART_HART_3V3_51K1_47K_4050B
/* EC console commands */
#define CONFIG_CMD_ACCELS
#define CONFIG_CMD_ACCEL_INFO
/* Sensors */
#define CONFIG_ACCEL_LIS2DE /* Lid accel */
#define CONFIG_ACCELGYRO_LSM6DSM /* Base accel */
/* Sensors without hardware FIFO are in forced mode */
#define CONFIG_ACCEL_FORCE_MODE_MASK BIT(LID_ACCEL)
#define CONFIG_LID_ANGLE
#define CONFIG_LID_ANGLE_UPDATE
#define CONFIG_LID_ANGLE_SENSOR_BASE BASE_ACCEL
#define CONFIG_LID_ANGLE_SENSOR_LID LID_ACCEL
#define CONFIG_DYNAMIC_MOTION_SENSOR_COUNT
#define CONFIG_ACCEL_LSM6DSM_INT_EVENT \
TASK_EVENT_MOTION_SENSOR_INTERRUPT(BASE_ACCEL)
/* Additional PPC second source */
#define CONFIG_USBC_PPC_SYV682X
#define CONFIG_USBC_PPC_DEDICATED_INT
#undef CONFIG_SYV682X_HV_ILIM
#define CONFIG_SYV682X_HV_ILIM SYV682X_HV_ILIM_5_50
/* SYV682 isn't connected to CC, so TCPC must provide VCONN */
#define CONFIG_USBC_PPC_SYV682X_NO_CC
#ifndef __ASSEMBLER__
#include "gpio_signal.h"
#include "registers.h"
enum adc_channel {
ADC_TEMP_SENSOR_AMB, /* ADC0 */
ADC_TEMP_SENSOR_CHARGER, /* ADC1 */
ADC_VBUS_C0, /* ADC9 */
ADC_VBUS_C1, /* ADC4 */
ADC_CH_COUNT,
};
enum temp_sensor_id {
TEMP_SENSOR_BATTERY,
TEMP_SENSOR_AMBIENT,
TEMP_SENSOR_CHARGER,
TEMP_SENSOR_COUNT
};
enum pwm_channel { PWM_CH_KBLIGHT, PWM_CH_COUNT };
/* Motion sensors */
enum sensor_id { LID_ACCEL, BASE_ACCEL, BASE_GYRO, SENSOR_COUNT };
/* List of possible batteries */
enum battery_type {
BATTERY_PANASONIC,
BATTERY_SMP,
BATTERY_LGC,
BATTERY_SUNWODA,
BATTERY_TYPE_COUNT,
};
#endif /* !__ASSEMBLER__ */
#endif /* __CROS_EC_BOARD_H */
|
