1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
|
/* Copyright (c) 2014 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Strago board-specific configuration */
#include "charger.h"
#include "charge_state.h"
#include "driver/accel_kxcj9.h"
#include "driver/temp_sensor/tmp432.h"
#include "extpower.h"
#include "gpio.h"
#include "host_command.h"
#include "i2c.h"
#include "lid_switch.h"
#include "math_util.h"
#include "motion_lid.h"
#include "motion_sense.h"
#include "power.h"
#include "power_button.h"
#include "registers.h"
#include "temp_sensor.h"
#include "temp_sensor_chip.h"
#include "thermal.h"
#include "util.h"
#define GPIO_KB_INPUT (GPIO_INPUT | GPIO_PULL_UP)
#define GPIO_KB_OUTPUT (GPIO_ODR_HIGH)
#define GPIO_KB_OUTPUT_COL2 (GPIO_OUT_LOW)
#include "gpio_list.h"
/* power signal list. Must match order of enum power_signal. */
const struct power_signal_info power_signal_list[] = {
{GPIO_ALL_SYS_PGOOD, 1, "ALL_SYS_PWRGD"},
{GPIO_RSMRST_L_PGOOD, 1, "RSMRST_N_PWRGD"},
{GPIO_PCH_SLP_S3_L, 1, "SLP_S3#_DEASSERTED"},
{GPIO_PCH_SLP_S4_L, 1, "SLP_S4#_DEASSERTED"},
};
BUILD_ASSERT(ARRAY_SIZE(power_signal_list) == POWER_SIGNAL_COUNT);
const struct i2c_port_t i2c_ports[] = {
{"batt_chg", 0, 100},
{"sensors", 1, 100},
{"pd_mcu", 2, 100},
{"thermal", 3, 100}
};
const unsigned int i2c_ports_used = ARRAY_SIZE(i2c_ports);
/*
* Temperature sensors data; must be in same order as enum temp_sensor_id.
* Sensor index and name must match those present in coreboot:
* src/mainboard/google/${board}/acpi/dptf.asl
*/
const struct temp_sensor_t temp_sensors[] = {
{"TMP432_Internal", TEMP_SENSOR_TYPE_BOARD, tmp432_get_val,
TMP432_IDX_LOCAL, 4},
{"TMP432_Sensor_1", TEMP_SENSOR_TYPE_BOARD, tmp432_get_val,
TMP432_IDX_REMOTE1, 4},
{"TMP432_Sensor_2", TEMP_SENSOR_TYPE_BOARD, tmp432_get_val,
TMP432_IDX_REMOTE2, 4},
{"Battery", TEMP_SENSOR_TYPE_BATTERY, charge_temp_sensor_get_val,
0, 4},
};
BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT);
/* Thermal limits for each temp sensor. All temps are in degrees K. Must be in
* same order as enum temp_sensor_id. To always ignore any temp, use 0.
*/
struct ec_thermal_config thermal_params[] = {
{{0, 0, 0}, 0, 0}, /* TMP432_Internal */
{{0, 0, 0}, 0, 0}, /* TMP432_Sensor_1 */
{{0, 0, 0}, 0, 0}, /* TMP432_Sensor_2 */
{{0, 0, 0}, 0, 0}, /* Battery Sensor */
};
BUILD_ASSERT(ARRAY_SIZE(thermal_params) == TEMP_SENSOR_COUNT);
int board_discharge_on_ac(int enable)
{
return charger_discharge_on_ac(enable);
}
/* Four Motion sensors */
/* kxcj9 mutex and local/private data*/
static struct mutex g_kxcj9_mutex[2];
struct kxcj9_data g_kxcj9_data[2];
/* Matrix to rotate accelrator into standard reference frame */
const matrix_3x3_t base_standard_ref = {
{ 0, FLOAT_TO_FP(1), 0},
{FLOAT_TO_FP(-1), 0, 0},
{ 0, 0, FLOAT_TO_FP(1)}
};
const matrix_3x3_t lid_standard_ref = {
{FLOAT_TO_FP(-1), 0, 0},
{ 0, FLOAT_TO_FP(-1), 0},
{ 0, 0, FLOAT_TO_FP(-1)}
};
struct motion_sensor_t motion_sensors[] = {
{SENSOR_ACTIVE_S0, "Base Accel", MOTIONSENSE_CHIP_KXCJ9,
MOTIONSENSE_TYPE_ACCEL, MOTIONSENSE_LOC_BASE,
&kxcj9_drv, &g_kxcj9_mutex[0], &g_kxcj9_data[0],
KXCJ9_ADDR1, &base_standard_ref, 100000, 2},
{SENSOR_ACTIVE_S0, "Lid Accel", MOTIONSENSE_CHIP_KXCJ9,
MOTIONSENSE_TYPE_ACCEL, MOTIONSENSE_LOC_LID,
&kxcj9_drv, &g_kxcj9_mutex[1], &g_kxcj9_data[1],
KXCJ9_ADDR0, &lid_standard_ref, 100000, 2},
};
const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
/* Define the accelerometer orientation matrices. */
const struct accel_orientation acc_orient = {
/* Hinge aligns with x axis. */
.rot_hinge_90 = {
{ FLOAT_TO_FP(1), 0, 0},
{ 0, 0, FLOAT_TO_FP(1)},
{ 0, FLOAT_TO_FP(-1), 0}
},
.rot_hinge_180 = {
{ FLOAT_TO_FP(1), 0, 0},
{ 0, FLOAT_TO_FP(-1), 0},
{ 0, 0, FLOAT_TO_FP(-1)}
},
.hinge_axis = {1, 0, 0},
};
|