1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
|
/* Copyright 2020 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Waddledee board-specific configuration */
#include "button.h"
#include "driver/accel_lis2dh.h"
#include "driver/accelgyro_lsm6dsm.h"
#include "driver/charger/sm5803.h"
#include "driver/sync.h"
#include "driver/retimer/tusb544.h"
#include "driver/temp_sensor/thermistor.h"
#include "driver/tcpm/anx7447.h"
#include "driver/usb_mux/it5205.h"
#include "gpio.h"
#include "hooks.h"
#include "intc.h"
#include "keyboard_scan.h"
#include "lid_switch.h"
#include "power.h"
#include "power_button.h"
#include "pwm.h"
#include "pwm_chip.h"
#include "switch.h"
#include "tablet_mode.h"
#include "task.h"
#include "temp_sensor.h"
#include "uart.h"
#include "usb_charge.h"
#include "usb_mux.h"
#include "usb_pd.h"
#define CPRINTUSB(format, args...) cprints(CC_USBCHARGE, format, ## args)
/* C0 interrupt line shared by BC 1.2 and charger */
static void usb_c0_interrupt(enum gpio_signal s)
{
task_set_event(TASK_ID_USB_CHG_P0, USB_CHG_EVENT_BC12, 0);
sm5803_interrupt(0);
}
/* C1 interrupt line shared by BC 1.2, TCPC, and charger */
static void usb_c1_interrupt(enum gpio_signal s)
{
schedule_deferred_pd_interrupt(1);
task_set_event(TASK_ID_USB_CHG_P1, USB_CHG_EVENT_BC12, 0);
sm5803_interrupt(1);
}
static void c0_ccsbu_ovp_interrupt(enum gpio_signal s)
{
cprints(CC_USBPD, "C0: CC OVP, SBU OVP, or thermal event");
pd_handle_cc_overvoltage(0);
}
/* Must come after other header files and interrupt handler declarations */
#include "gpio_list.h"
/* USB Retimer */
const struct usb_mux usbc1_retimer = {
.usb_port = 1,
.i2c_port = I2C_PORT_SUB_USB_C1,
.i2c_addr_flags = TUSB544_I2C_ADDR_FLAGS0,
.driver = &tusb544_drv,
};
/* USB Muxes */
const struct usb_mux usb_muxes[CONFIG_USB_PD_PORT_MAX_COUNT] = {
{
.usb_port = 0,
.i2c_port = I2C_PORT_USB_C0,
.i2c_addr_flags = IT5205_I2C_ADDR1_FLAGS,
.driver = &it5205_usb_mux_driver,
},
{
.usb_port = 1,
.i2c_port = I2C_PORT_SUB_USB_C1,
.i2c_addr_flags = AN7447_TCPC0_I2C_ADDR_FLAGS,
.driver = &anx7447_usb_mux_driver,
.next_mux = &usbc1_retimer,
},
};
void board_init(void)
{
int on;
gpio_enable_interrupt(GPIO_USB_C0_INT_ODL);
gpio_enable_interrupt(GPIO_USB_C1_INT_ODL);
gpio_enable_interrupt(GPIO_USB_C0_CCSBU_OVP_ODL);
/* Charger on the MB will be outputting PROCHOT_ODL and OD CHG_DET */
sm5803_configure_gpio0(CHARGER_PRIMARY, GPIO0_MODE_PROCHOT, 1);
sm5803_configure_chg_det_od(CHARGER_PRIMARY, 1);
/* Charger on the sub-board will be a push-pull GPIO */
sm5803_configure_gpio0(CHARGER_SECONDARY, GPIO0_MODE_OUTPUT, 0);
/* Turn on 5V if the system is on, otherwise turn it off */
on = chipset_in_state(CHIPSET_STATE_ON | CHIPSET_STATE_ANY_SUSPEND);
board_power_5v_enable(on);
}
DECLARE_HOOK(HOOK_INIT, board_init, HOOK_PRIO_DEFAULT);
void board_reset_pd_mcu(void)
{
/*
* Nothing to do. TCPC C0 is internal, TCPC C1 reset pin is not
* connected to the EC.
*/
}
__override void board_power_5v_enable(int enable)
{
/*
* Motherboard has a GPIO to turn on the 5V regulator, but the sub-board
* sets it through the charger GPIO.
*/
gpio_set_level(GPIO_EN_PP5000, !!enable);
if (sm5803_set_gpio0_level(1, !!enable))
CPRINTUSB("Failed to %sable sub rails!", enable ? "en" : "dis");
}
/* PWM channels. Must be in the exactly same order as in enum pwm_channel. */
const struct pwm_t pwm_channels[] = {
[PWM_CH_KBLIGHT] = {
.channel = 0,
.flags = PWM_CONFIG_DSLEEP,
.freq_hz = 10000,
},
[PWM_CH_LED_RED] = {
.channel = 1,
.flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW,
.freq_hz = 2400,
},
[PWM_CH_LED_GREEN] = {
.channel = 2,
.flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW,
.freq_hz = 2400,
},
[PWM_CH_LED_BLUE] = {
.channel = 3,
.flags = PWM_CONFIG_DSLEEP | PWM_CONFIG_ACTIVE_LOW,
.freq_hz = 2400,
}
};
BUILD_ASSERT(ARRAY_SIZE(pwm_channels) == PWM_CH_COUNT);
/* Sensor Mutexes */
static struct mutex g_lid_mutex;
static struct mutex g_base_mutex;
/* Sensor Data */
static struct stprivate_data g_lis2dh_data;
static struct lsm6dsm_data lsm6dsm_data = LSM6DSM_DATA;
/* Drivers */
struct motion_sensor_t motion_sensors[] = {
[LID_ACCEL] = {
.name = "Lid Accel",
.active_mask = SENSOR_ACTIVE_S0_S3,
.chip = MOTIONSENSE_CHIP_LIS2DE,
.type = MOTIONSENSE_TYPE_ACCEL,
.location = MOTIONSENSE_LOC_LID,
.drv = &lis2dh_drv,
.mutex = &g_lid_mutex,
.drv_data = &g_lis2dh_data,
.port = I2C_PORT_SENSOR,
.i2c_spi_addr_flags = LIS2DH_ADDR1_FLAGS,
.rot_standard_ref = NULL,
.default_range = 2, /* g */
/* We only use 2g because its resolution is only 8-bits */
.min_frequency = LIS2DH_ODR_MIN_VAL,
.max_frequency = LIS2DH_ODR_MAX_VAL,
.config = {
[SENSOR_CONFIG_EC_S0] = {
.odr = 10000 | ROUND_UP_FLAG,
},
[SENSOR_CONFIG_EC_S3] = {
.odr = 10000 | ROUND_UP_FLAG,
},
},
},
[BASE_ACCEL] = {
.name = "Base Accel",
.active_mask = SENSOR_ACTIVE_S0_S3,
.chip = MOTIONSENSE_CHIP_LSM6DSM,
.type = MOTIONSENSE_TYPE_ACCEL,
.location = MOTIONSENSE_LOC_BASE,
.drv = &lsm6dsm_drv,
.mutex = &g_base_mutex,
.drv_data = LSM6DSM_ST_DATA(lsm6dsm_data,
MOTIONSENSE_TYPE_ACCEL),
.int_signal = GPIO_BASE_SIXAXIS_INT_L,
.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
.port = I2C_PORT_SENSOR,
.i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
.rot_standard_ref = NULL,
.default_range = 4, /* g */
.min_frequency = LSM6DSM_ODR_MIN_VAL,
.max_frequency = LSM6DSM_ODR_MAX_VAL,
.config = {
[SENSOR_CONFIG_EC_S0] = {
.odr = 13000 | ROUND_UP_FLAG,
.ec_rate = 100 * MSEC,
},
[SENSOR_CONFIG_EC_S3] = {
.odr = 10000 | ROUND_UP_FLAG,
.ec_rate = 100 * MSEC,
},
},
},
[BASE_GYRO] = {
.name = "Base Gyro",
.active_mask = SENSOR_ACTIVE_S0_S3,
.chip = MOTIONSENSE_CHIP_LSM6DSM,
.type = MOTIONSENSE_TYPE_GYRO,
.location = MOTIONSENSE_LOC_BASE,
.drv = &lsm6dsm_drv,
.mutex = &g_base_mutex,
.drv_data = LSM6DSM_ST_DATA(lsm6dsm_data,
MOTIONSENSE_TYPE_GYRO),
.int_signal = GPIO_BASE_SIXAXIS_INT_L,
.flags = MOTIONSENSE_FLAG_INT_SIGNAL,
.port = I2C_PORT_SENSOR,
.i2c_spi_addr_flags = LSM6DSM_ADDR0_FLAGS,
.default_range = 1000 | ROUND_UP_FLAG, /* dps */
.rot_standard_ref = NULL,
.min_frequency = LSM6DSM_ODR_MIN_VAL,
.max_frequency = LSM6DSM_ODR_MAX_VAL,
},
[VSYNC] = {
.name = "Camera VSYNC",
.active_mask = SENSOR_ACTIVE_S0,
.chip = MOTIONSENSE_CHIP_GPIO,
.type = MOTIONSENSE_TYPE_SYNC,
.location = MOTIONSENSE_LOC_CAMERA,
.drv = &sync_drv,
.default_range = 0,
.min_frequency = 0,
.max_frequency = 1,
},
};
const unsigned int motion_sensor_count = ARRAY_SIZE(motion_sensors);
/* Thermistors */
const struct temp_sensor_t temp_sensors[] = {
[TEMP_SENSOR_1] = {.name = "Memory",
.type = TEMP_SENSOR_TYPE_BOARD,
.read = get_temp_3v3_51k1_47k_4050b,
.idx = ADC_TEMP_SENSOR_1},
[TEMP_SENSOR_2] = {.name = "Ambient",
.type = TEMP_SENSOR_TYPE_BOARD,
.read = get_temp_3v3_51k1_47k_4050b,
.idx = ADC_TEMP_SENSOR_2},
};
BUILD_ASSERT(ARRAY_SIZE(temp_sensors) == TEMP_SENSOR_COUNT);
#ifndef TEST_BUILD
/* This callback disables keyboard when convertibles are fully open */
void lid_angle_peripheral_enable(int enable)
{
int chipset_in_s0 = chipset_in_state(CHIPSET_STATE_ON);
/*
* If the lid is in tablet position via other sensors,
* ignore the lid angle, which might be faulty then
* disable keyboard.
*/
if (tablet_get_mode())
enable = 0;
if (enable) {
keyboard_scan_enable(1, KB_SCAN_DISABLE_LID_ANGLE);
} else {
/*
* Ensure that the chipset is off before disabling the keyboard.
* When the chipset is on, the EC keeps the keyboard enabled and
* the AP decides whether to ignore input devices or not.
*/
if (!chipset_in_s0)
keyboard_scan_enable(0, KB_SCAN_DISABLE_LID_ANGLE);
}
}
#endif
|