1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
|
/* Copyright (c) 2013 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* Configuration for Wolf mainboard */
#ifndef __BOARD_H
#define __BOARD_H
/* Optional features */
#define CONFIG_BACKLIGHT_X86
#define CONFIG_BATTERY_SMART
#define CONFIG_BOARD_VERSION
#define CONFIG_CHARGER
#define CONFIG_CHARGER_BQ24707A
#define CONFIG_CHIPSET_HASWELL
#define CONFIG_CHIPSET_X86
#define CONFIG_EXTPOWER_GPIO
#define CONFIG_KEYBOARD_BOARD_CONFIG
#define CONFIG_KEYBOARD_PROTOCOL_8042
#define CONFIG_POWER_BUTTON
#define CONFIG_POWER_BUTTON_X86
#define CONFIG_PWM_FAN
#define CONFIG_TEMP_SENSOR
#define CONFIG_UART_HOST 2
#define CONFIG_TEMP_SENSOR_G781
#define CONFIG_USB_PORT_POWER_DUMB
#define CONFIG_WIRELESS
#ifndef __ASSEMBLER__
/* Module IDs */
/* TODO(rspangler): use this in place of enum console_channel as well */
enum module_id {
MODULE_I2C,
MODULE_LPC,
MODULE_PECI,
MODULE_PWM_FAN,
MODULE_UART,
};
/* PWM channels */
#define FAN_CH_CPU 2 /* CPU fan */
#define FAN_CH_BL_DISPLAY 4 /* LVDS backlight (from PCH, cleaned by EC) */
/* I2C ports */
#define I2C_PORT_BATTERY 0
#define I2C_PORT_CHARGER 0
#define I2C_PORT_THERMAL 5
/* There are only two I2C ports used because battery and charger share a port */
#define I2C_PORTS_USED 2
/* 13x8 keyboard scanner uses an entire GPIO bank for row inputs */
#define KB_SCAN_ROW_IRQ LM4_IRQ_GPIOK
#define KB_SCAN_ROW_GPIO LM4_GPIO_K
/* Host connects to keyboard controller module via LPC */
#define HOST_KB_BUS_LPC
/* USB ports */
#define USB_PORT_COUNT 2
/* GPIO signal definitions. */
enum gpio_signal {
/* Inputs with interrupt handlers are first for efficiency */
GPIO_POWER_BUTTON_L = 0, /* Power button */
GPIO_LID_OPEN, /* Lid switch */
GPIO_AC_PRESENT, /* AC power present */
GPIO_PCH_BKLTEN, /* Backlight enable signal from PCH */
GPIO_PCH_SLP_S0_L, /* SLP_S0# signal from PCH */
GPIO_PCH_SLP_S3_L, /* SLP_S3# signal from PCH */
GPIO_PCH_SLP_S5_L, /* SLP_S5# signal from PCH */
GPIO_PCH_SLP_SUS_L, /* SLP_SUS# signal from PCH */
GPIO_PP1050_PGOOD, /* Power good on 1.05V */
GPIO_PP1350_PGOOD, /* Power good on 1.35V (DRAM) */
GPIO_PP5000_PGOOD, /* Power good on 5V */
GPIO_VCORE_PGOOD, /* Power good on core VR */
GPIO_PCH_EDP_VDD_EN, /* PCH wants EDP enabled */
GPIO_RECOVERY_L, /* Recovery signal from servo */
GPIO_WP_L, /* Write protect input */
/* Other inputs */
GPIO_FAN_ALERT_L, /* From thermal sensor */
GPIO_PCH_SUSWARN_L, /* SUSWARN# signal from PCH */
GPIO_USB1_OC_L, /* USB port overcurrent warning */
GPIO_USB2_OC_L, /* USB port overcurrent warning */
GPIO_BOARD_VERSION1, /* Board version stuffing resistor 1 */
GPIO_BOARD_VERSION2, /* Board version stuffing resistor 2 */
GPIO_BOARD_VERSION3, /* Board version stuffing resistor 3 */
GPIO_CPU_PGOOD, /* Power good to the CPU */
/* Outputs */
GPIO_CPU_PROCHOT, /* Force CPU to think it's overheated */
GPIO_PP1350_EN, /* Enable 1.35V supply */
GPIO_PP3300_DSW_GATED_EN, /* Enable DSW rails */
GPIO_PP3300_DX_EN, /* Enable power to lots of peripherals */
GPIO_PP3300_LTE_EN, /* Enable LTE radio */
GPIO_PP3300_WLAN_EN, /* Enable WiFi power */
GPIO_SUSP_VR_EN, /* Enable 1.05V regulator */
GPIO_VCORE_EN, /* Stuffing option - not connected */
GPIO_PP5000_EN, /* Enable 5V supply */
GPIO_SYS_PWROK, /* EC thinks everything is up and ready */
GPIO_WLAN_OFF_L, /* Disable WiFi radio */
GPIO_CHARGE_L, /* Allow battery to charge when on AC */
GPIO_ENABLE_BACKLIGHT, /* Enable backlight power */
GPIO_ENABLE_TOUCHPAD, /* Enable touchpad power */
GPIO_ENTERING_RW, /* Indicate when EC is entering RW code */
GPIO_PCH_DPWROK, /* Indicate when VccDSW is good */
GPIO_PCH_HDA_SDO, /* HDA_SDO signal to PCH; when high, ME
* ignores security descriptor */
GPIO_PCH_WAKE_L, /* Wake signal from EC to PCH */
GPIO_PCH_NMI_L, /* Non-maskable interrupt pin to PCH */
GPIO_PCH_PWRBTN_L, /* Power button output to PCH */
GPIO_PCH_PWROK, /* PWROK / APWROK signals to PCH */
GPIO_PCH_RCIN_L, /* RCIN# line to PCH (for 8042 emulation) */
GPIO_PCH_RSMRST_L, /* Reset PCH resume power plane logic */
GPIO_PCH_SMI_L, /* System management interrupt to PCH */
GPIO_TOUCHSCREEN_RESET_L, /* Reset touch screen */
GPIO_EC_EDP_VDD_EN, /* Enable EDP (passthru from PCH) */
GPOI_LPC_CLKRUN_L, /* Dunno. Probably important, though. */
GPIO_USB1_ENABLE, /* USB port 1 output power enable */
GPIO_USB2_ENABLE, /* USB port 2 output power enable */
GPIO_PCH_SUSACK_L, /* Acknowledge PCH SUSWARN# signal */
GPIO_PCH_RTCRST_L, /* Not supposed to be here */
GPIO_PCH_SRTCRST_L, /* Not supposed to be here */
GPIO_BAT_LED0_L, /* Battery charging LED - Blue */
GPIO_BAT_LED1_L, /* Battery charging LED - Amber */
/* Number of GPIOs; not an actual GPIO */
GPIO_COUNT
};
/* x86 signal definitions */
enum x86_signal {
X86_PGOOD_PP5000 = 0,
X86_PGOOD_PP1350,
X86_PGOOD_PP1050,
X86_PGOOD_VCORE,
X86_PCH_SLP_S0n_DEASSERTED,
X86_PCH_SLP_S3n_DEASSERTED,
X86_PCH_SLP_S5n_DEASSERTED,
X86_PCH_SLP_SUSn_DEASSERTED,
/* Number of X86 signals */
X86_SIGNAL_COUNT
};
/* Charger module */
#define CONFIG_CHARGER_SENSE_RESISTOR 10 /* Charge sense resistor, mOhm */
#define CONFIG_CHARGER_SENSE_RESISTOR_AC 10 /* Input sensor resistor, mOhm */
/*FIXME needed to be checked, use the same as Peppy*/
#define CONFIG_CHARGER_INPUT_CURRENT 3078 /* mA, need be checked */
enum adc_channel {
/* EC internal die temperature in degrees K. */
ADC_CH_EC_TEMP = 0,
/* HEY: Be prepared to read this (ICMNT). */
/* Charger current in mA. */
ADC_CH_CHARGER_CURRENT,
ADC_CH_COUNT
};
enum temp_sensor_id {
/* CPU die temperature via PECI */
TEMP_SENSOR_CPU_PECI = 0,
/* EC internal temperature sensor */
TEMP_SENSOR_EC_INTERNAL,
/* G781 internal and external sensors */
TEMP_SENSOR_I2C_G781_INTERNAL,
TEMP_SENSOR_I2C_G781_EXTERNAL,
TEMP_SENSOR_COUNT
};
/**
* Board-specific g781 power state.
*/
int board_g781_has_power(void);
/* Target value for BOOTCFG. This is set to PE2/USB1_CTL1, which has an external
* pullup. If this signal is pulled to ground when the EC boots, the EC will get
* into the boot loader and we can recover bricked EC. */
#define BOOTCFG_VALUE 0x7fff88fe
/* Wireless signals */
#define WIRELESS_GPIO_WLAN GPIO_WLAN_OFF_L
#define WIRELESS_GPIO_WWAN GPIO_PP3300_LTE_EN
#define WIRELESS_GPIO_WLAN_POWER GPIO_PP3300_WLAN_EN
#endif /* !__ASSEMBLER__ */
#endif /* __BOARD_H */
|
