1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
|
/*
* Copyright 2015 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
#include "common.h"
#include "registers.h"
#include "uart.h"
#define UART_NCO ((16 * BIT(UART_NCO_WIDTH) * \
(long long)CONFIG_UART_BAUD_RATE) / PCLK_FREQ)
/* 115200N81 uart0, TX on A0, RX on A1 */
void uart_init(void)
{
/* Pinmux init also turns on all clocks. */
GREG32(PMU, PERICLKSET0) = 0xffffffff;
GREG32(PMU, PERICLKSET1) = 0xffffffff;
/*
* hardwire clocks to some value... just to get going
* Set source of trim to calibration logic during dynamic trim
*/
GWRITE_FIELD(XO, CLK_TIMER_TRIM_CTRL, RC_COARSE_TRIM_SRC, 0);
/* Set initial coarse trim value (slowest) */
GREG32(XO, CLK_TIMER_RC_COARSE_ATE_TRIM) = 100;
/* Set initial trim stabilization period */
GWRITE_FIELD(XO, CLK_TIMER_TRIM_CTRL, RC_INITIAL_TRIM_PERIOD, 10);
/* enable trim */
GWRITE_FIELD(XO, CLK_TIMER_TRIM_CTRL, RC_TRIM_EN, 1);
/* domain crossing sync */
GREG32(XO, CLK_TIMER_SYNC_CONTENTS) = 0x1;
GREG32(PINMUX, DIOA0_SEL) = GC_PINMUX_UART0_TX_SEL;
GREG32(PINMUX, UART0_RX_SEL) = GC_PINMUX_DIOA1_SEL;
GREG32(PINMUX, DIOA1_CTL) =
GC_PINMUX_DIOA1_CTL_DS_MASK | GC_PINMUX_DIOA1_CTL_IE_MASK;
GREG32(PMU, PWRDN_SCRATCH3) = 0xbeefcafe;
GREG32(UART, FIFO) = 3; /* clear RX,TX FIFO */
GREG32(UART, NCO) = UART_NCO; /* 115200N81 */
GREG32(UART, CTRL) = 3; /* TX,RX enable */
uart_write_char('\n');
uart_write_char('\r');
}
int uart_tx_ready(void)
{
/*
* This makes sure that transmit FIFO is fully flashed, so that TX
* FIFO is not used.
*/
return GREAD_FIELD(UART, STATE, TXIDLE);
}
void uart_tx_flush(void)
{
}
int uart_init_done(void)
{
return 1;
}
void uart_tx_start(void)
{
}
void uart_tx_stop(void)
{
}
void uart_write_char(char c)
{
while (!uart_tx_ready())
;
GREG32(UART, WDATA) = c;
}
|
