1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
|
/* Copyright 2013 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* UART module for MEC1322 */
#include "clock.h"
#include "common.h"
#include "console.h"
#include "gpio.h"
#include "lpc.h"
#include "registers.h"
#include "system.h"
#include "task.h"
#include "uart.h"
#include "util.h"
#define TX_FIFO_SIZE 16
static int init_done;
static int tx_fifo_used;
int uart_init_done(void)
{
return init_done;
}
void uart_tx_start(void)
{
/* If interrupt is already enabled, nothing to do */
if (MEC1322_UART_IER & BIT(1))
return;
/* Do not allow deep sleep while transmit in progress */
disable_sleep(SLEEP_MASK_UART);
/*
* Re-enable the transmit interrupt, then forcibly trigger the
* interrupt. This works around a hardware problem with the
* UART where the FIFO only triggers the interrupt when its
* threshold is _crossed_, not just met.
*/
MEC1322_UART_IER |= BIT(1);
task_trigger_irq(MEC1322_IRQ_UART);
}
void uart_tx_stop(void)
{
MEC1322_UART_IER &= ~BIT(1);
/* Re-allow deep sleep */
enable_sleep(SLEEP_MASK_UART);
}
void uart_tx_flush(void)
{
/* Wait for transmit FIFO empty */
while (!(MEC1322_UART_LSR & MEC1322_LSR_TX_EMPTY))
;
}
int uart_tx_ready(void)
{
/*
* We have no indication of free space in transmit FIFO. To work around
* this, we check transmit FIFO empty bit every 16 characters written.
*/
return tx_fifo_used != 0 || (MEC1322_UART_LSR & MEC1322_LSR_TX_EMPTY);
}
int uart_tx_in_progress(void)
{
/* return 0: FIFO is empty, 1: FIFO NOT Empty */
return !(MEC1322_UART_LSR & MEC1322_LSR_TX_EMPTY);
}
int uart_rx_available(void)
{
return MEC1322_UART_LSR & BIT(0);
}
void uart_write_char(char c)
{
/* Wait for space in transmit FIFO. */
while (!uart_tx_ready())
;
tx_fifo_used = (tx_fifo_used + 1) % TX_FIFO_SIZE;
MEC1322_UART_TB = c;
}
int uart_read_char(void)
{
return MEC1322_UART_RB;
}
static void uart_clear_rx_fifo(int channel)
{
MEC1322_UART_FCR = BIT(0) | BIT(1);
}
/**
* Interrupt handler for UART
*/
static void uart_ec_interrupt(void)
{
/* Read input FIFO until empty, then fill output FIFO */
uart_process_input();
uart_process_output();
}
DECLARE_IRQ(MEC1322_IRQ_UART, uart_ec_interrupt, 1);
void uart_init(void)
{
/* Set UART to reset on VCC1_RESET instaed of nSIO_RESET */
MEC1322_UART_CFG &= ~BIT(1);
/* Baud rate = 115200. 1.8432MHz clock. Divisor = 1 */
/* Set CLK_SRC = 0 */
MEC1322_UART_CFG &= ~BIT(0);
/* Set DLAB = 1 */
MEC1322_UART_LCR |= BIT(7);
/* PBRG0/PBRG1 */
MEC1322_UART_PBRG0 = 1;
MEC1322_UART_PBRG1 = 0;
/* Set DLAB = 0 */
MEC1322_UART_LCR &= ~BIT(7);
/* Set word length to 8-bit */
MEC1322_UART_LCR |= BIT(0) | BIT(1);
/* Enable FIFO */
MEC1322_UART_FCR = BIT(0);
/* Activate UART */
MEC1322_UART_ACT |= BIT(0);
/*
clock_enable_peripheral(CGC_OFFSET_UART, mask,
CGC_MODE_RUN | CGC_MODE_SLEEP);*/
gpio_config_module(MODULE_UART, 1);
/*
* Enable interrupts for UART0.
*/
uart_clear_rx_fifo(0);
MEC1322_UART_IER |= BIT(0);
MEC1322_UART_MCR |= BIT(3);
MEC1322_INT_ENABLE(15) |= BIT(0);
MEC1322_INT_BLK_EN |= BIT(15);
task_enable_irq(MEC1322_IRQ_UART);
init_done = 1;
}
#ifdef CONFIG_LOW_POWER_IDLE
void uart_enter_dsleep(void)
{
/* Disable the UART interrupt. */
task_disable_irq(MEC1322_IRQ_UART); /* NVIC interrupt for UART=13 */
/*
* Set the UART0 RX pin to be a GPIO-162(fixed pin) interrupt
* with the flags defined in the gpio.inc file.
*/
gpio_reset(GPIO_UART0_RX);
/* power-down/de-activate UART0 */
MEC1322_UART_ACT &= ~BIT(0);
/* Clear pending interrupts on GPIO_UART0_RX(GPIO162, girq=8, bit=18) */
MEC1322_INT_SOURCE(8) = (1 << 18);
/* Enable GPIO interrupts on the UART0 RX pin. */
gpio_enable_interrupt(GPIO_UART0_RX);
}
void uart_exit_dsleep(void)
{
/*
* If the UART0 RX GPIO interrupt has not fired, then no edge has been
* detected. Disable the GPIO interrupt so that switching the pin over
* to a UART pin doesn't inadvertently cause a GPIO edge interrupt.
* Note: we can't disable this interrupt if it has already fired
* because then the IRQ will not run at all.
*/
if (!(BIT(18) & MEC1322_INT_SOURCE(8))) /* if edge interrupt */
gpio_disable_interrupt(GPIO_UART0_RX);
/* Configure UART0 pins for use in UART peripheral. */
gpio_config_module(MODULE_UART, 1);
/* Clear pending interrupts on UART peripheral and enable interrupts. */
uart_clear_rx_fifo(0);
task_enable_irq(MEC1322_IRQ_UART); /* NVIC interrupt for UART = 13 */
/* power-up/activate UART0 */
MEC1322_UART_ACT |= BIT(0);
}
void uart_deepsleep_interrupt(enum gpio_signal signal)
{
/*
* Activity seen on UART RX pin while UART was disabled for deep sleep.
* The console won't see that character because the UART is disabled,
* so we need to inform the clock module of UART activity ourselves.
*/
clock_refresh_console_in_use();
/* Disable interrupts on UART0 RX pin to avoid repeated interrupts. */
gpio_disable_interrupt(GPIO_UART0_RX);
}
#endif /* CONFIG_LOW_POWER_IDLE */
|