1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
# Fingerprint Debugging
This document describes how to attach a debugger with SWD in order to debug the
FPMCU.
[TOC]
## Overview
### SWD
`SWD` (Single Wire Debug) was introduced by ARM with the Cortex-M family to
reduce the pin count required by JTAG. JTAG requires 5 pins, but SWD can be done
with only 3 pins. Furthermore, one of the freed up pins can be repurposed for
tracing.
See [CoreSight Connectors] for details on the three standard types of connectors
used for JTAG and SWD for ARM devices.
## Hardware Required
* JTAG/SWD Debugger Probe: Any debug probe that supports SWD will work, but
this document assumes that you're using a
[Segger J-Trace PRO for Cortex-M][J-Trace].
* [Dragonclaw v0.2 Development board][FPMCU dev board].
* [Servo Micro].
## Software Required
* [JLink Software] \(when using [J-Trace] or other Segger debug probes).
* Any tool that supports connecting `gdbserver`. This document will assume
[CLion] and was tested with `JLink_Linux_V684a_x86_64`.
* Alternatively, you can use [Ozone] a standalone debugger from Segger.
## Connecting SWD
The connector for SWD is `J4` on Dragonclaw v0.2.
<!-- mdformat off(b/139308852) -->
*** note
**NOTE**: Pay attention to the location of pin 1 (red wire) in the
photos below so that you connect with the correct orientation.
`SW2` on the bottom of Dragonclaw must be set to `CORESIGHT`.
If you want to connect a 20-Pin ARM Standard JTAG Connector (0.10" / 2.54 mm),
you can use the following [adapter][JTAG to SWD Adapter] and [cable][SWD Cable].
***
<!-- mdformat on -->
Dragonclaw v0.2 with 20-pin SWD (0.05" / 1.27mm) on J4. Only half the pins are connected. |
----------------------------------------------------------------------------------------- |
![Dragonclaw with 20-pin SWD] |
Dragonclaw v0.2 with 10-pin SWD (0.05" / 1.27mm) on J4. |
------------------------------------------------------- |
![Dragonclaw with 10-pin SWD] |
## Powering the Board
[Servo Micro] can provide both the 3.3V for the MCU and 1.8V for the sensor.
Run the following to start `servod`, which will enable power to these rails by
default:
```bash
(chroot) $ sudo servod --board=dragonclaw
```
It's also possible to power through J-Trace, though this can only supply the MCU
with power (3.3V), not a sensor using 1.8V.
## Using JLink gdbserver
Start the JLink gdbserver for the appropriate MCU type:
* Dragonclaw / [Nucleo STM32F412ZG]: `STM32F412CG`
* Dragontalon / [Nucleo STM32H743ZI]: `STM32H743ZI`
```bash
(outside) $ ./JLink_Linux_V684a_x86_64/JLinkGDBServerCLExe -select USB -device STM32F412CG -endian little -if SWD -speed auto -noir -noLocalhostOnly
```
You should see the port that gdbserver is running on in the output:
```bash
Connecting to J-Link...
J-Link is connected.
Firmware: J-Trace PRO V2 Cortex-M compiled Dec 13 2019 11:19:22
Hardware: V2.00
S/N: XXXXX
Feature(s): RDI, FlashBP, FlashDL, JFlash, GDB
Checking target voltage...
Target voltage: 3.30 V
Listening on TCP/IP port 2331 <--- gdbserver port
Connecting to target...
Connected to target
Waiting for GDB connection...
```
Configure your editor to use this [`.gdbinit`], taking care to set the correct
environment variables for the `BOARD` and `GDBSERVER` being used. For CLion, if
you want to use a `.gdbinit` outside of your `HOME` directory, you'll need to
[configure `~/.gdbinit`].
In your editor, specify the IP address and port for `gdbserver`:
```
127.0.0.1:2331
```
You will also want to provide the symbol files:
* RW image: `build/<board>/RW/ec.RW.elf`
* RO image: `build/<board>/RO.ec.RO.elf`
Also, since we're compiling the firmware in the chroot, but your editor is
running outside of the chroot, you'll want to remap the source code path to
account for this:
* "Remote source" is the path inside the chroot:
`/home/<username>/trunk/src/platform/ec`
* "Local source" is the path outside the chroot:
`${HOME}/chromiumos/src/platform/ec`
To debug with CLion, you will create a new [GDB Remote Debug Configuration]
called `EC Debug`, with:
* `'target remote' args` (gdbserver IP and port from above): `127.0.0.1:2331`
* `Symbol file` (RW or RO ELF): `/path/to/build/<board>/RW/ec.RW.elf`
* `Path mapping`: Add remote to local source path mapping as described above.
After configuring this if you select the `EC Debug` target in CLion and
[click the debug icon][CLion Start Remote Debug], CLion and JLink will handle
automatically flashing the ELF file and stepping through breakpoints in the
code. Even if not debugging, this may help with your iterative development flow
since the JLink tool can flash very quickly since it performs a differential
flash. Note that you still need to recompile after making changes to the source
code before launching the debugger.
## Using Ozone
Ozone is a free standalone debugger provided by Segger that works with the
[J-Trace]. You may want to use it if you need more powerful debug features than
gdbserver can provide. For example, Ozone has a register mapping for the MCUs we
use, so you can easily inspect CPU registers. It can also be automated with a
scripting language and show code coverage when used with a [J-Trace] that is
connected to the trace pins on a board. Note that the Dragonclaw v0.2 uses an
STM32F412 package that does not have the synchronous trace pins, but the
[Nucleo STM32F412ZG] does have the trace pins.
[CoreSight Connectors]: http://www2.keil.com/coresight/coresight-connectors
[FPMCU dev board]: ./fingerprint-dev-for-partners.md#fpmcu-dev-board
[J-Trace]: https://www.segger.com/products/debug-probes/j-trace/models/j-trace/
[JLink Software]: https://www.segger.com/downloads/jlink/#J-LinkSoftwareAndDocumentationPack
[Servo Micro]: ./fingerprint-dev-for-partners.md#Servo-Micro
[JTAG to SWD Adapter]: https://www.adafruit.com/product/2094
[SWD Cable]: https://www.adafruit.com/product/1675
[Ozone]: https://www.segger.com/products/development-tools/ozone-j-link-debugger/
[CLion]: https://www.jetbrains.com/clion/
[GDB Remote Debug Configuration]: https://www.jetbrains.com/help/clion/remote-debug.html#remote-config
[CLion Start Remote Debug]: https://www.jetbrains.com/help/clion/remote-debug.html#start-remote-debug
[Nucleo STM32F412ZG]: https://www.st.com/en/evaluation-tools/nucleo-f412zg.html
[Nucleo STM32H743ZI]: https://www.st.com/en/evaluation-tools/nucleo-h743zi.html
[`.gdbinit`]: /util/gdbinit
[configure `~/.gdbinit`]: https://www.jetbrains.com/help/clion/configuring-debugger-options.html#gdbinit-lldbinit
<!-- Images -->
[Dragonclaw with 20-pin SWD]: ../images/dragonclaw_with_20_pin_swd.jpg
[Dragonclaw with 10-pin SWD]: ../images/dragonclaw_with_10_pin_swd.jpg
|
