1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
|
/* Copyright (c) 2012 The Chromium OS Authors. All rights reserved.
* Use of this source code is governed by a BSD-style license that can be
* found in the LICENSE file.
*/
/* GPIO module for Chrome EC */
#ifndef __CROS_EC_GPIO_H
#define __CROS_EC_GPIO_H
#include "common.h"
/* Flag definitions for gpio_info. */
#define GPIO_INPUT 0x0000 /* Input */
#define GPIO_OUTPUT 0x0001 /* Output */
#define GPIO_OPEN_DRAIN 0x0002 /* Output type is open-drain */
#define GPIO_PULL_UP 0x0004 /* Enable on-chip pullup */
#define GPIO_PULL_DOWN 0x0008 /* Enable on-chip pulldown */
#define GPIO_LOW 0x0010 /* If GPIO_OUTPUT, set level low */
#define GPIO_HIGH 0x0020 /* If GPIO_OUTPUT, set level high */
#define GPIO_INT_RISING 0x0040 /* Interrupt on rising edge */
#define GPIO_INT_FALLING 0x0080 /* Interrupt on falling edge */
#define GPIO_INT_BOTH 0x0100 /* Interrupt on both edges */
#define GPIO_INT_LOW 0x0200 /* Interrupt on low level */
#define GPIO_INT_HIGH 0x0400 /* Interrupt on high level */
#define GPIO_DEFAULT 0x0800 /* Don't set up on boot */
/* Common flag combinations */
#define GPIO_OUT_LOW (GPIO_OUTPUT | GPIO_LOW)
#define GPIO_OUT_HIGH (GPIO_OUTPUT | GPIO_HIGH)
#define GPIO_ODR_HIGH (GPIO_OUTPUT | GPIO_OPEN_DRAIN | GPIO_HIGH)
#define GPIO_ODR_LOW (GPIO_OUTPUT | GPIO_OPEN_DRAIN | GPIO_LOW)
#define GPIO_INT_EDGE (GPIO_INT_RISING | GPIO_INT_FALLING | GPIO_INT_BOTH)
#define GPIO_INT_LEVEL (GPIO_INT_LOW | GPIO_INT_HIGH)
#define GPIO_INT_ANY (GPIO_INT_EDGE | GPIO_INT_LEVEL)
/* Note that if no flags are present, the signal is a high-Z input */
/* GPIO signal definition structure, for use by board.c */
struct gpio_info {
const char *name;
int port; /* Port (LM4_GPIO_*) */
int mask; /* Bitmask on that port (0x01 - 0x80; 0x00 =
* signal not implemented) */
uint32_t flags; /* Flags (GPIO_*) */
/*
* Interrupt handler. If non-NULL, and the signal's interrupt is
* enabled, this will be called in the context of the GPIO interrupt
* handler.
*/
void (*irq_handler)(enum gpio_signal signal);
};
/* Signal information from board.c. Must match order from enum gpio_signal. */
extern const struct gpio_info gpio_list[];
/* Macro for signals which don't exist */
#ifdef CHIP_lm4
#define GPIO_SIGNAL_NOT_IMPLEMENTED(name) {name, LM4_GPIO_A, 0, 0, NULL}
#else
#define GPIO_SIGNAL_NOT_IMPLEMENTED(name) {name, GPIO_A, 0, 0, NULL}
#endif
/**
* Pre-initialize GPIOs.
*
* This occurs before clocks or tasks are set up.
*/
void gpio_pre_init(void);
/**
* Get the current value of a signal.
*
* @param signal Signal to get
* @return 0 if low, 1 if high.
*/
int gpio_get_level(enum gpio_signal signal);
/**
* Get faster access to a GPIO level.
*
* Use this function to find out the register address and mask for a GPIO
* value. Then you can just check that instead of calling gpio_get_level().
*
* @param signal Signal to return details for
* @param mask Mask value to use
* @return pointer to register to read to get GPIO value
*/
uint16_t *gpio_get_level_reg(enum gpio_signal signal, uint32_t *mask);
/**
* Return the name of a given GPIO signal.
*
* @param signal Signal to name
* @returns name of the given signal
*/
const char *gpio_get_name(enum gpio_signal signal);
/**
* Set the flags for a signal.
*
* @param signal Signal to set flags for
* @param flags New flags for the signal
*/
void gpio_set_flags(enum gpio_signal signal, int flags);
/**
* Set the value of a signal.
*
* @param signal Signal to set
* @param value New value for signal (0 = low, != high */
void gpio_set_level(enum gpio_signal signal, int value);
/**
* Enable interrupts for the signal.
*
* The signal must have been defined with
* an interrupt handler. Normally called by the module which handles the
* interrupt, once it's ready to start processing interrupts.
*
* @param signal Signal to enable interrrupts for
* @return EC_SUCCESS, or non-zero if error.
*/
int gpio_enable_interrupt(enum gpio_signal signal);
/**
* Set alternate function for GPIO(s).
*
* This is intended for use by other modules' configure_gpio() functions.
*
* @param port GPIO port to set (LM4_GPIO_*)
* @param mask Bitmask of pins on that port to affect
* @param func Alternate function; if <0, configures the specified
* GPIOs for normal GPIO operation.
*/
void gpio_set_alternate_function(int port, int mask, int func);
#endif /* __CROS_EC_GPIO_H */
|
