blob: 0b670885dde65a93645655c811a3f64329980e85 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
|
# Copyright 2021 The Chromium OS Authors. All rights reserved.
# Use of this source code is governed by a BSD-style license that can be
# found in the LICENSE file.
# Zephyr Kernel Configuration
CONFIG_SOC_SERIES_NPCX7=y
CONFIG_SOC_NPCX7M6FC=y
# Platform Configuration
CONFIG_BOARD_VOLTEER=y
# NPCX BootLoader Table Configuration
CONFIG_PLATFORM_EC_RO_HEADER_CORE_CLOCK_SPI_CLOCK_RATIO_2=y
CONFIG_PLATFORM_EC_RO_HEADER_SPI_MAX_CLOCK_50=y
CONFIG_PLATFORM_EC_RO_HEADER_SPI_READ_MODE_DUAL=y
# Serial Drivers
CONFIG_SERIAL=y
CONFIG_UART_INTERRUPT_DRIVEN=y
# Enable console
CONFIG_CONSOLE=y
CONFIG_UART_CONSOLE=y
# Pinmux Driver
CONFIG_PINMUX=y
# GPIO Controller
CONFIG_GPIO=y
# Clock configuration
CONFIG_CLOCK_CONTROL=y
# WATCHDOG configuration
CONFIG_WATCHDOG=y
# Set the delay time for printing panic data.
# 1 cycle is about 32ms. 500ms is about 16 cycles.
CONFIG_WDT_NPCX_DELAY_CYCLES=16
# PLL configuration
CONFIG_CLOCK_NPCX_OSC_CYCLES_PER_SEC=90000000
CONFIG_CLOCK_NPCX_APB1_PRESCALER=6
CONFIG_CLOCK_NPCX_APB2_PRESCALER=6
CONFIG_CLOCK_NPCX_APB3_PRESCALER=6
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=15000000
# The following are valid for all:
# Code RAM base for NPCX797FC
CONFIG_CROS_EC_PROGRAM_MEMORY_BASE=0x10070000
CONFIG_CROS_EC_RAM_BASE=0x200c0000
CONFIG_CROS_EC_DATA_RAM_SIZE=0x00010000
CONFIG_CROS_EC_RAM_SIZE=0x0000f800
# Image size: MAX (1/2 Flash size, Code RAM size)
# For NPCX796FC: Flash = 512 KiB, Code Ram 192 KiB
# For NPCX797FC: Flash = 512 KiB, Code Ram 320 KiB
CONFIG_CROS_EC_RO_MEM_OFF=0x0
CONFIG_CROS_EC_RO_SIZE=0x40000
# RW firmware in program memory - Identical to RO, only one image loaded at a
# time.
CONFIG_CROS_EC_RW_MEM_OFF=0x0
CONFIG_CROS_EC_RW_SIZE=0x40000
CONFIG_CROS_EC_HOOK_TICK_INTERVAL=200000
# ADC
# The resolution and oversamplig values are fixed by the NPCX ADC driver
CONFIG_ADC=y
CONFIG_ADC_SHELL=n
CONFIG_PLATFORM_EC_ADC_RESOLUTION=10
CONFIG_PLATFORM_EC_ADC_OVERSAMPLING=0
# Power Management
CONFIG_SOC_POWER_MANAGEMENT=y
CONFIG_PM_POLICY_APP=y
CONFIG_UART_CONSOLE_INPUT_EXPIRED=y
CONFIG_SOC_POWER_MANAGEMENT_TRACE=y
CONFIG_FLASH_SIZE=512
|
