From ced540c3852b39919b31b52cf90d836dd2824552 Mon Sep 17 00:00:00 2001 From: uwe Date: Sat, 16 May 2009 21:39:19 +0000 Subject: Add proper workaround for 3COM 3C90xB cards, which need special fixups (the 3C90xC ones don't). This is tested on hardware. Also, add initial support for the Atmel AT29C010A chip (which I inserted in a 3COM 3C90xB card for testing). It can be detected, read works, erase works, but write will need some additional code (will post in another patch later). Signed-off-by: Uwe Hermann Acked-by: Carl-Daniel Hailfinger git-svn-id: https://code.coreboot.org/svn/flashrom/trunk@520 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1 --- nic3com.c | 26 +++++++++++++++++++++++++- 1 file changed, 25 insertions(+), 1 deletion(-) (limited to 'nic3com.c') diff --git a/nic3com.c b/nic3com.c index f5d0aa1..4e3e475 100644 --- a/nic3com.c +++ b/nic3com.c @@ -29,13 +29,17 @@ #define BIOS_ROM_ADDR 0x04 #define BIOS_ROM_DATA 0x08 #define INT_STATUS 0x0e +#define INTERNAL_CONFIG 0x00 #define SELECT_REG_WINDOW 0x800 #define PCI_VENDOR_ID_3COM 0x10b7 +uint32_t internal_conf; +uint16_t id; + struct pcidev_status nics_3com[] = { /* 3C90xB */ - {0x10b7, 0x9055, PCI_NT, "3COM", "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-TX"}, + {0x10b7, 0x9055, PCI_OK, "3COM", "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-TX"}, {0x10b7, 0x9001, PCI_NT, "3COM", "3C90xB: PCI 10/100 Mbps; shared 10BASE-T/100BASE-T4" }, {0x10b7, 0x9004, PCI_NT, "3COM", "3C90xB: PCI 10BASE-T (TPO)" }, {0x10b7, 0x9005, PCI_NT, "3COM", "3C90xB: PCI 10BASE-T/10BASE2/AUI (COMBO)" }, @@ -57,6 +61,18 @@ int nic3com_init(void) get_io_perms(); io_base_addr = pcidev_init(PCI_VENDOR_ID_3COM, nics_3com); + id = pcidev_dev->device_id; + + /* 3COM 3C90xB cards need a special fixup. */ + if (id == 0x9055 || id == 0x9001 || id == 0x9004 || id == 0x9005 + || id == 0x9006 || id == 0x900a || id == 0x905a) { + /* Select register window 3 and save the receiver status. */ + OUTW(SELECT_REG_WINDOW + 3, io_base_addr + INT_STATUS); + internal_conf = INL(io_base_addr + INTERNAL_CONFIG); + + /* Set receiver type to MII for full BIOS ROM access. */ + OUTL((internal_conf & 0xf00fffff) | 0x00600000, io_base_addr); + } /* * The lowest 16 bytes of the I/O mapped register space of (most) 3COM @@ -70,6 +86,14 @@ int nic3com_init(void) int nic3com_shutdown(void) { + /* 3COM 3C90xB cards need a special fixup. */ + if (id == 0x9055 || id == 0x9001 || id == 0x9004 || id == 0x9005 + || id == 0x9006 || id == 0x900a || id == 0x905a) { + /* Select register window 3 and restore the receiver status. */ + OUTW(SELECT_REG_WINDOW + 3, io_base_addr + INT_STATUS); + OUTL(internal_conf, io_base_addr + INTERNAL_CONFIG); + } + free(pcidev_bdf); pci_cleanup(pacc); #if defined(__FreeBSD__) || defined(__DragonFly__) -- cgit v1.2.1