diff options
Diffstat (limited to 'FreeRTOS/Demo/RISC-V_RV64_PolarFire_SoftConsole/polarfire_hal/boards/icicle-kit-es/fpga_design_config/general/hw_gen_peripherals.h')
-rw-r--r-- | FreeRTOS/Demo/RISC-V_RV64_PolarFire_SoftConsole/polarfire_hal/boards/icicle-kit-es/fpga_design_config/general/hw_gen_peripherals.h | 61 |
1 files changed, 61 insertions, 0 deletions
diff --git a/FreeRTOS/Demo/RISC-V_RV64_PolarFire_SoftConsole/polarfire_hal/boards/icicle-kit-es/fpga_design_config/general/hw_gen_peripherals.h b/FreeRTOS/Demo/RISC-V_RV64_PolarFire_SoftConsole/polarfire_hal/boards/icicle-kit-es/fpga_design_config/general/hw_gen_peripherals.h new file mode 100644 index 000000000..b099d7502 --- /dev/null +++ b/FreeRTOS/Demo/RISC-V_RV64_PolarFire_SoftConsole/polarfire_hal/boards/icicle-kit-es/fpga_design_config/general/hw_gen_peripherals.h @@ -0,0 +1,61 @@ +/******************************************************************************* + * Copyright 2019-2021 Microchip FPGA Embedded Systems Solutions. + * + * SPDX-License-Identifier: MIT + * + * @file hw_gen_peripherals.h + * @author Microchip-FPGA Embedded Systems Solutions + * + * + * Note 1: This file should not be edited. If you need to modify a parameter + * without going through regenerating using the MSS Configurator Libero flow + * or editing the associated xml file + * the following method is recommended: + + * 1. edit the following file + * boards/your_board/platform_config/mpfs_hal_config/mss_sw_config.h + + * 2. define the value you want to override there. + * (Note: There is a commented example in the platform directory) + + * Note 2: The definition in mss_sw_config.h takes precedence, as + * mss_sw_config.h is included prior to the generated header files located in + * boards/your_board/fpga_design_config + * + */ + +#ifndef HW_GEN_PERIPHERALS_H_ +#define HW_GEN_PERIPHERALS_H_ + + +#ifdef __cplusplus +extern "C" { +#endif + +#if !defined (LIBERO_SETTING_GPIO_CR) +/*GPIO Blocks reset control- (soft_reset options chossen in Libero confgurator) +*/ +#define LIBERO_SETTING_GPIO_CR 0x000F0703UL + /* GPIO0_SOFT_RESET_SELECT [0:2] RW value= 0x3 */ + /* GPIO0_DEFAULT [4:2] RW value= 0x0 */ + /* GPIO1_SOFT_RESET_SELECT [8:3] RW value= 0x7 */ + /* GPIO1_DEFAULT [12:3] RW value= 0x0 */ + /* GPIO2_SOFT_RESET_SELECT [16:4] RW value= 0xF */ + /* GPIO2_DEFAULT [20:4] RW value= 0x0 */ +#endif +#if !defined (LIBERO_SETTING_CRYPTO_CR_INFO) +/*Information on how Crypto setup on this MPFS */ +#define LIBERO_SETTING_CRYPTO_CR_INFO 0x00000000UL + /* MSS_MODE [0:2] RO */ + /* RESERVED [2:1] RO */ + /* STREAM_ENABLE [3:1] RO */ + /* RESERVED1 [4:28] RO */ +#endif + +#ifdef __cplusplus +} +#endif + + +#endif /* #ifdef HW_GEN_PERIPHERALS_H_ */ + |