--- type: reference, howto --- # Rack Attack initializer ## Overview [Rack Attack](https://github.com/kickstarter/rack-attack), also known as Rack::Attack, is a Ruby gem that is meant to protect GitLab with the ability to customize throttling and to block user IP addresses. You can prevent brute-force passwords attacks, scrapers, or any other offenders by throttling requests from IP addresses that are making large volumes of requests. If you find throttling is not enough to protect you against abusive clients, Rack Attack offers IP whitelisting, blacklisting, Fail2ban style filtering, and tracking. For more information on how to use these options see the [Rack Attack README](https://github.com/kickstarter/rack-attack/blob/master/README.md). NOTE: **Note:** See [User and IP rate limits](../user/admin_area/settings/user_and_ip_rate_limits.md) for simpler limits that are configured in the UI. NOTE: **Note:** Starting with GitLab 11.2, Rack Attack is disabled by default. If your instance is not exposed to the public internet, it is recommended that you leave Rack Attack disabled. ## Behavior If set up as described in the [Settings](#settings) section below, two behaviors will be enabled: - Protected paths will be throttled. - Failed authentications for Git and container registry requests will trigger a temporary IP ban. ### Protected paths throttle GitLab responds with HTTP status code `429` to POST requests at protected paths that exceed 10 requests per minute per IP address. By default, protected paths are: - `/users/password` - `/users/sign_in` - `/api/#{API::API.version}/session.json` - `/api/#{API::API.version}/session` - `/users` - `/users/confirmation` - `/unsubscribes/` - `/import/github/personal_access_token` - `/admin/session` This header is included in responses to blocked requests: ```plaintext Retry-After: 60 ``` For example, the following are limited to a maximum 10 requests per minute: - User sign-in - User sign-up (if enabled) - User password reset After 10 requests, the client must wait a minute before it can try again. ### Git and container registry failed authentication ban GitLab responds with HTTP status code `403` for 1 hour, if 30 failed authentication requests were received in a 3-minute period from a single IP address. This applies only to Git requests and container registry (`/jwt/auth`) requests (combined). This limit: - Is reset by requests that authenticate successfully. For example, 29 failed authentication requests followed by 1 successful request, followed by 29 more failed authentication requests would not trigger a ban. - Does not apply to JWT requests authenticated by `gitlab-ci-token`. No response headers are provided. ## Settings **Omnibus GitLab** 1. Open `/etc/gitlab/gitlab.rb` with your editor 1. Add the following: ```ruby gitlab_rails['rack_attack_git_basic_auth'] = { 'enabled' => true, 'ip_whitelist' => ["127.0.0.1"], 'maxretry' => 10, # Limit the number of Git HTTP authentication attempts per IP 'findtime' => 60, # Reset the auth attempt counter per IP after 60 seconds 'bantime' => 3600 # Ban an IP for one hour (3600s) after too many auth attempts } ``` 1. Reconfigure GitLab: ```shell sudo gitlab-ctl reconfigure ``` The following settings can be configured: - `enabled`: By default this is set to `false`. Set this to `true` to enable Rack Attack. - `ip_whitelist`: Whitelist any IPs from being blocked. They must be formatted as strings within a Ruby array. CIDR notation is supported in GitLab v12.1 and up. For example, `["127.0.0.1", "127.0.0.2", "127.0.0.3", "192.168.0.1/24"]`. - `maxretry`: The maximum amount of times a request can be made in the specified time. - `findtime`: The maximum amount of time that failed requests can count against an IP before it's blacklisted (in seconds). - `bantime`: The total amount of time that a blacklisted IP will be blocked (in seconds). **Installations from source** NOTE: **Note:** Rack Attack initializer was temporarily renamed to `rack_attack_new`, to support backwards compatibility with the one [Omnibus initializer](https://docs.gitlab.com/omnibus/settings/configuration.html#setting-up-paths-to-be-protected-by-rack-attack). It'll be renamed back to `rack_attack.rb` once Omnibus throttle is removed. Please see the [GitLab issue](https://gitlab.com/gitlab-org/gitlab/issues/29952) for more information. These settings can be found in `config/initializers/rack_attack.rb`. If you are missing `config/initializers/rack_attack.rb`, the following steps need to be taken in order to enable protection for your GitLab instance: 1. In `config/application.rb` find and uncomment the following line: ```ruby config.middleware.use Rack::Attack ``` 1. Restart GitLab: ```shell sudo service gitlab restart ``` If you want more restrictive/relaxed throttle rules, edit `config/initializers/rack_attack.rb` and change the `limit` or `period` values. For example, more relaxed throttle rules will be if you set `limit: 3` and `period: 1.seconds` (this will allow 3 requests per second). You can also add other paths to the protected list by adding to `paths_to_be_protected` variable. If you change any of these settings you must restart your GitLab instance. ## Remove blocked IPs from Rack Attack via Redis In case you want to remove a blocked IP, follow these steps: 1. Find the IPs that have been blocked in the production log: ```shell grep "Rack_Attack" /var/log/gitlab/gitlab-rails/auth.log ``` 1. Since the blacklist is stored in Redis, you need to open up `redis-cli`: ```shell /opt/gitlab/embedded/bin/redis-cli -s /var/opt/gitlab/redis/redis.socket ``` 1. You can remove the block using the following syntax, replacing `` with the actual IP that is blacklisted: ```plaintext del cache:gitlab:rack::attack:allow2ban:ban: ``` 1. Confirm that the key with the IP no longer shows up: ```plaintext keys *rack::attack* ``` 1. Optionally, add the IP to the whitelist to prevent it from being blacklisted again (see [settings](#settings)). ## Troubleshooting ### Rack attack is blacklisting the load balancer Rack Attack may block your load balancer if all traffic appears to come from the load balancer. In that case, you will need to: 1. [Configure `nginx[real_ip_trusted_addresses]`](https://docs.gitlab.com/omnibus/settings/nginx.html#configuring-gitlab-trusted_proxies-and-the-nginx-real_ip-module). This will keep users' IPs from being listed as the load balancer IPs. 1. Whitelist the load balancer's IP address(es) in the Rack Attack [settings](#settings). 1. Reconfigure GitLab: ```shell sudo gitlab-ctl reconfigure ``` 1. [Remove the block via Redis.](#remove-blocked-ips-from-rack-attack-via-redis)