/* $Id$ */ /* * Handle the Garmin binary packet format supported by the USB Garmins * tested with the Garmin 18 and other models. This driver is NOT for * serial port connected Garmins, they provide adequate NMEA support. * * This code is partly from the Garmin IOSDK and partly from the * sample code in the Linux garmin_gps driver. * * This code supports both Garmin on a serial port and USB Garmins. * * USB Garmins need the Linux garmin_gps driver and will not function * without it. This code has been tested and at least at one time is * known to work on big- and little-endian CPUs and 32 and 64 bit cpu * modes. * * Protocol info from: * GPS18_TechnicalSpecification.pdf * iop_spec.pdf * http://www.garmin.com/support/commProtocol.html * * bad code by: Gary E. Miller * all rights abandoned, a thank would be nice if you use this code. * * -D 3 = packet trace * -D 4 = packet details * -D 5 = more packet details * -D 6 = very excessive details * * limitations: * * do not have from garmin: * pdop * hdop * vdop * magnetic variation * * known bugs: * hangs in the fread loop instead of keeping state and returning. * may or may not work on a little-endian machine */ #define __USE_POSIX199309 1 #include #include // for nanosleep() #include #include #include #include #include #include #include #include "gpsd_config.h" #if defined (HAVE_SYS_SELECT_H) #include #endif #if defined(HAVE_STRINGS_H) #include #endif #include "gpsd.h" #include "gps.h" #ifdef GARMIN_ENABLE #define GARMIN_LAYERID_TRANSPORT (uint8_t) 0 #define GARMIN_LAYERID_APPL (uint32_t) 20 // Linux Garmin USB driver layer-id to use for some control mechanisms #define GARMIN_LAYERID_PRIVATE 0x01106E4B // packet ids used in private layer #define PRIV_PKTID_SET_DEBUG 1 #define PRIV_PKTID_SET_MODE 2 #define PRIV_PKTID_INFO_REQ 3 #define PRIV_PKTID_INFO_RESP 4 #define PRIV_PKTID_RESET_REQ 5 #define PRIV_PKTID_SET_DEF_MODE 6 #define MODE_NATIVE 0 #define MODE_GARMIN_SERIAL 1 #define GARMIN_PKTID_TRANSPORT_START_SESSION_REQ 5 #define GARMIN_PKTID_TRANSPORT_START_SESSION_RESP 6 #define GARMIN_PKTID_PROTOCOL_ARRAY 253 #define GARMIN_PKTID_PRODUCT_RQST 254 #define GARMIN_PKTID_PRODUCT_DATA 255 /* 0x33 '3' */ #define GARMIN_PKTID_PVT_DATA 51 /* 0x72 'r' */ #define GARMIN_PKTID_SAT_DATA 114 #define GARMIN_PKTID_L001_XFER_CMPLT 12 #define GARMIN_PKTID_L001_COMMAND_DATA 10 #define GARMIN_PKTID_L001_DATE_TIME_DATA 14 #define GARMIN_PKTID_L001_RECORDS 27 #define GARMIN_PKTID_L001_WPT_DATA 35 #define CMND_ABORT 0 #define CMND_START_PVT_DATA 49 #define CMND_STOP_PVT_DATA 50 #define CMND_START_RM_DATA 110 #define MAX_BUFFER_SIZE 4096 #define GARMIN_CHANNELS 12 // something magic about 64, garmin driver will not return more than // 64 at a time. If you read less than 64 bytes the next read will // just get the last of the 64 byte buffer. #define ASYNC_DATA_SIZE 64 #pragma pack(1) // This is the data format of the satellite data from the garmin USB typedef struct { uint8_t svid; uint16_t snr; // 0 - 0xffff uint8_t elev; uint16_t azmth; uint8_t status; // bit 0, has ephemeris, 1, has diff correction // bit 2 used in solution // bit 3?? } cpo_sat_data; /* Garmin D800_Pvt_Date_Type */ // This is the data format of the position data from the garmin USB typedef struct { float alt; /* altitude above WGS 84 (meters) */ float epe; /* estimated position error, 2 sigma (meters) */ float eph; /* epe, but horizontal only (meters) */ float epv; /* epe but vertical only (meters ) */ int16_t fix; /* 0 - failed integrity check * 1 - invalid or unavailable fix * 2 - 2D * 3 - 3D * 4 - 2D Diff * 5 - 3D Diff */ double gps_tow; /* gps time os week (seconds) */ double lat; /* ->latitude (radians) */ double lon; /* ->longitude (radians) */ float lon_vel; /* velocity east (meters/second) */ float lat_vel; /* velocity north (meters/second) */ float alt_vel; /* velocity up (meters/sec) */ float msl_hght; /* height of WGS 84 above MSL (meters) */ int16_t leap_sec; /* diff between GPS and UTC (seconds) */ int32_t grmn_days; } cpo_pvt_data; #ifdef __UNUSED__ typedef struct { uint32_t cycles; double pr; uint16_t phase; int8_t slp_dtct; uint8_t snr_dbhz; int8_t svid; int8_t valid; } cpo_rcv_sv_data; typedef struct { double rcvr_tow; int16_t rcvr_wn; cpo_rcv_sv_data sv[GARMIN_CHANNELS]; } cpo_rcv_data; #endif /* __UNUSED__ */ // This is the packet format to/from the Garmin USB typedef struct { uint8_t mPacketType; uint8_t mReserved1; uint16_t mReserved2; uint16_t mPacketId; uint16_t mReserved3; uint32_t mDataSize; union { int8_t chars[MAX_BUFFER_SIZE]; uint8_t uchars[MAX_BUFFER_SIZE]; cpo_pvt_data pvt; cpo_sat_data sats; } mData; } Packet_t; // useful funcs to read/write ints // floats and doubles are Intel order only... static inline void set_int16(uint8_t *buf, uint32_t value) { buf[0] = (uint8_t)(0x0FF & value); buf[1] = (uint8_t)(0x0FF & (value >> 8)); } static inline void set_int32(uint8_t *buf, uint32_t value) { buf[0] = (uint8_t)(0x0FF & value); buf[1] = (uint8_t)(0x0FF & (value >> 8)); buf[2] = (uint8_t)(0x0FF & (value >> 16)); buf[3] = (uint8_t)(0x0FF & (value >> 24)); } static inline uint16_t get_uint16(const uint8_t *buf) { return (uint16_t)(0xFF & buf[0]) | ((uint16_t)(0xFF & buf[1]) << 8); } static inline uint32_t get_int32(const uint8_t *buf) { return (uint32_t)(0xFF & buf[0]) | ((uint32_t)(0xFF & buf[1]) << 8) | ((uint32_t)(0xFF & buf[2]) << 16) | ((uint32_t)(0xFF & buf[3]) << 24); } // convert radians to degrees static inline double radtodeg( double rad) { return (double)(rad * RAD_2_DEG ); } static gps_mask_t PrintSERPacket(struct gps_device_t *session, unsigned char pkt_id, int pkt_len, unsigned char *buf ); static gps_mask_t PrintUSBPacket(struct gps_device_t *session, Packet_t *pkt ); static int GetPacket (struct gps_device_t *session ); gps_mask_t PrintSERPacket(struct gps_device_t *session, unsigned char pkt_id , int pkt_len, unsigned char *buf ) { gps_mask_t mask = 0; int i = 0, j = 0; uint16_t prod_id = 0; uint16_t ver = 0; int maj_ver; int min_ver; time_t time_l = 0; double track; char msg_buf[512] = ""; char *msg = NULL; cpo_sat_data *sats = NULL; cpo_pvt_data *pvt = NULL; gpsd_report(4, "PrintSERPacket(, %#02x, %#02x, )\n", pkt_id, pkt_len); switch( pkt_id ) { case GARMIN_PKTID_L001_COMMAND_DATA: prod_id = get_uint16((uint8_t *)buf); /*@ -branchstate @*/ switch ( prod_id ) { case CMND_ABORT: msg = "Abort current xfer"; break; case CMND_START_PVT_DATA: msg = "Start Xmit PVT data"; break; case CMND_STOP_PVT_DATA: msg = "Stop Xmit PVT data"; break; case CMND_START_RM_DATA: msg = "Start RMD data"; break; default: (void)snprintf(msg_buf, sizeof(msg_buf), "Unknown: %u", (unsigned int)prod_id); msg = msg_buf; break; } /*@ +branchstate @*/ gpsd_report(3, "Appl, Command Data: %s\n", msg); break; case GARMIN_PKTID_PRODUCT_RQST: gpsd_report(3, "Appl, Product Data req\n"); break; case GARMIN_PKTID_PRODUCT_DATA: prod_id = get_uint16((uint8_t *)buf); ver = get_uint16((uint8_t *)&buf[2]); maj_ver = (int)(ver / 100); min_ver = (int)(ver - (maj_ver * 100)); gpsd_report(3, "Appl, Product Data, sz: %d\n", pkt_len); gpsd_report(1, "Garmin Product ID: %d, SoftVer: %d.%02d\n" , prod_id, maj_ver, min_ver); gpsd_report(1, "Garmin Product Desc: %s\n" , &buf[4]); break; case GARMIN_PKTID_PVT_DATA: gpsd_report(3, "Appl, PVT Data Sz: %d\n", pkt_len); pvt = (cpo_pvt_data*) buf; // 631065600, unix seconds for 31 Dec 1989 Zulu time_l = (time_t)(631065600 + (pvt->grmn_days * 86400)); time_l -= pvt->leap_sec; session->context->leap_seconds = pvt->leap_sec; session->context->valid = LEAP_SECOND_VALID; // gps_tow is always like x.999 or x.998 so just round it time_l += (time_t) round(pvt->gps_tow); session->gpsdata.fix.time = session->gpsdata.sentence_time = (double)time_l; gpsd_report(5, "time_l: %ld\n", (long int)time_l); session->gpsdata.fix.latitude = radtodeg(pvt->lat); session->gpsdata.fix.longitude = radtodeg(pvt->lon); // altitude over WGS84 converted to MSL session->gpsdata.fix.altitude = pvt->alt + pvt->msl_hght; // geoid separation from WGS 84 // gpsd sign is opposite of garmin sign session->gpsdata.separation = -pvt->msl_hght; // Estimated position error in meters. session->gpsdata.epe = pvt->epe * (GPSD_CONFIDENCE/2); session->gpsdata.fix.eph = pvt->eph * (GPSD_CONFIDENCE/2); session->gpsdata.fix.epv = pvt->epv * (GPSD_CONFIDENCE/2); // convert lat/lon to directionless speed session->gpsdata.fix.speed = hypot(pvt->lon_vel, pvt->lat_vel); // keep climb in meters/sec session->gpsdata.fix.climb = pvt->alt_vel; track = atan2(pvt->lon_vel, pvt->lat_vel); if (track < 0) { track += 2 * PI; } session->gpsdata.fix.track = radtodeg(track); switch ( pvt->fix) { case 0: case 1: default: // no fix session->gpsdata.status = STATUS_NO_FIX; session->gpsdata.fix.mode = MODE_NO_FIX; break; case 2: // 2D fix session->gpsdata.status = STATUS_FIX; session->gpsdata.fix.mode = MODE_2D; break; case 3: // 3D fix session->gpsdata.status = STATUS_FIX; session->gpsdata.fix.mode = MODE_3D; break; case 4: // 2D Differential fix session->gpsdata.status = STATUS_DGPS_FIX; session->gpsdata.fix.mode = MODE_2D; break; case 5: // 3D differential fix session->gpsdata.status = STATUS_DGPS_FIX; session->gpsdata.fix.mode = MODE_3D; break; } #ifdef NTPSHM_ENABLE if (session->gpsdata.fix.mode > MODE_NO_FIX) (void) ntpshm_put(session, session->gpsdata.fix.time); #endif /* NTPSHM_ENABLE */ gpsd_report(4, "Appl, mode %d, status %d\n" , session->gpsdata.fix.mode , session->gpsdata.status); gpsd_report(3, "UTC Time: %lf\n", session->gpsdata.fix.time); gpsd_report(3 , "Geoid Separation (MSL-WGS84): from garmin %lf, calculated %lf\n" , -pvt->msl_hght , wgs84_separation(session->gpsdata.fix.latitude , session->gpsdata.fix.longitude)); gpsd_report(3, "Alt: %.3f, Epe: %.3f, Eph: %.3f, Epv: %.3f, Fix: %d, Gps_tow: %f, Lat: %.3f, Lon: %.3f, LonVel: %.3f, LatVel: %.3f, AltVel: %.3f, MslHgt: %.3f, Leap: %d, GarminDays: %ld\n" , pvt->alt , pvt->epe , pvt->eph , pvt->epv , pvt->fix , pvt->gps_tow , session->gpsdata.fix.latitude , session->gpsdata.fix.longitude , pvt->lon_vel , pvt->lat_vel , pvt->alt_vel , pvt->msl_hght , pvt->leap_sec , pvt->grmn_days); mask |= TIME_SET | LATLON_SET | ALTITUDE_SET | STATUS_SET | MODE_SET | SPEED_SET | TRACK_SET | CLIMB_SET | HERR_SET | VERR_SET | PERR_SET | CYCLE_START_SET; break; case GARMIN_PKTID_SAT_DATA: gpsd_report(3, "Appl, SAT Data Sz: %d\n", pkt_len); sats = (cpo_sat_data *)buf; session->gpsdata.satellites_used = 0; memset(session->gpsdata.used,0,sizeof(session->gpsdata.used)); gpsd_zero_satellites(&session->gpsdata); for ( i = 0, j = 0 ; i < GARMIN_CHANNELS ; i++, sats++ ) { gpsd_report(4," Sat %d, snr: %d, elev: %d, Azmth: %d, Stat: %x\n" , sats->svid , sats->snr , sats->elev , sats->azmth , sats->status); if ( 255 == (int)sats->svid ) { // Garmin uses 255 for empty // gpsd uses 0 for empty continue; } session->gpsdata.PRN[j] = (int)sats->svid; session->gpsdata.azimuth[j] = (int)sats->azmth; session->gpsdata.elevation[j] = (int)sats->elev; // snr units?? // garmin 0 -> 0xffff, NMEA 99 -> 0 session->gpsdata.ss[j] = 99 - (int)((100 *( unsigned long)sats->snr) >> 16); if ( (uint8_t)0 != (sats->status & 4 ) ) { // used in solution? session->gpsdata.used[session->gpsdata.satellites_used++] = (int)sats->svid; } session->gpsdata.satellites++; j++; } mask |= SATELLITE_SET | USED_SET; break; case GARMIN_PKTID_PROTOCOL_ARRAY: // this packet is never requested, it just comes, in some case // after a GARMIN_PKTID_PRODUCT_RQST gpsd_report(3, "Appl, Product Capability, sz: %d\n", pkt_len); for ( i = 0; i < pkt_len ; i += 3 ) { gpsd_report(3, " %c%03d\n", buf[i], get_uint16((uint8_t *)&buf[i+1] ) ); } break; default: gpsd_report(3, "Appl, ID: %d, Sz: %d\n" , pkt_id, pkt_len); break; } gpsd_report(3, "PrintSERPacket(, %#02x, %#02x, ) = %#02x\n" , pkt_id, pkt_len, mask); return mask; } /*@ -branchstate @*/ // For debugging, decodes and prints some known packets. static gps_mask_t PrintUSBPacket(struct gps_device_t *session, Packet_t *pkt) { gps_mask_t mask = 0; int maj_ver; int min_ver; uint32_t mode = 0; uint16_t prod_id = 0; uint32_t veri = 0; uint32_t serial; uint32_t mDataSize = get_int32( (uint8_t*)&pkt->mDataSize); gpsd_report(3, "PrintUSBPacket()\n"); if ( 4096 < mDataSize) { gpsd_report(3, "bogus packet, size too large=%d\n", mDataSize); return 0; } (void)snprintf(session->gpsdata.tag, sizeof(session->gpsdata.tag), "%u" , (unsigned int)pkt->mPacketType); switch ( pkt->mPacketType ) { case GARMIN_LAYERID_TRANSPORT: /* Garmin USB layer specific */ switch( pkt->mPacketId ) { case GARMIN_PKTID_TRANSPORT_START_SESSION_REQ: gpsd_report(3, "Transport, Start Session req\n"); break; case GARMIN_PKTID_TRANSPORT_START_SESSION_RESP: mode = get_int32(&pkt->mData.uchars[0]); gpsd_report(3, "Transport, Start Session resp, unit: 0x%x\n" , mode); break; default: gpsd_report(3, "Transport, Packet: Type %d %d %d, ID: %d, Sz: %d\n" , pkt->mPacketType , pkt->mReserved1 , pkt->mReserved2 , pkt->mPacketId , mDataSize); break; } break; case GARMIN_LAYERID_APPL: /* raw data transport, shared with Garmin Serial Driver */ mask = PrintSERPacket(session, (unsigned char)pkt->mPacketId, (int)mDataSize, (unsigned char *)pkt->mData.uchars); break; case 75: // private, garmin USB kernel driver specific switch( pkt->mPacketId ) { case PRIV_PKTID_SET_MODE: prod_id = get_uint16(&pkt->mData.uchars[0]); gpsd_report(3, "Private, Set Mode: %d\n", prod_id); break; case PRIV_PKTID_INFO_REQ: gpsd_report(3, "Private, ID: Info Req\n"); break; case PRIV_PKTID_INFO_RESP: veri = get_int32(pkt->mData.uchars); maj_ver = (int)(veri >> 16); min_ver = (int)(veri & 0xffff); mode = get_int32(&pkt->mData.uchars[4]); serial = get_int32(&pkt->mData.uchars[8]); gpsd_report(3, "Private, ID: Info Resp\n"); gpsd_report(1, "Garmin USB Driver found, Version %d.%d, Mode: %d, GPS Serial# %u\n" , maj_ver, min_ver, mode, serial); break; default: gpsd_report(3, "Private, Packet: ID: %d, Sz: %d\n" , pkt->mPacketId , mDataSize); break; } break; default: gpsd_report(3, "Packet: Type %d %d %d, ID: %d, Sz: %d\n" , pkt->mPacketType , pkt->mReserved1 , pkt->mReserved2 , pkt->mPacketId , mDataSize); break; } return mask; } /*@ +branchstate @*/ /* build and send a packet */ static void Build_Send_Packet( struct gps_device_t *session, uint32_t layer_id, uint32_t pkt_id, uint32_t length, uint32_t data ) { uint8_t *buffer = (uint8_t *)session->driver.garmin.Buffer; Packet_t *thePacket = (Packet_t*)buffer; ssize_t theBytesReturned = 0; ssize_t theBytesToWrite = 12 + (ssize_t)length; set_int32(buffer, layer_id); set_int32(buffer+4, pkt_id); set_int32(buffer+8, length); if ( 2 == length ) { set_int16(buffer+12, data); } else if ( 4 == length ) { set_int32(buffer+12, data); } #if 0 gpsd_report(4, "SendPacket(), writing %d bytes: %s\n" , theBytesToWrite, gpsd_hexdump(thePacket, theBytesToWrite)); #endif (void)PrintUSBPacket ( session, thePacket); theBytesReturned = write( session->gpsdata.gps_fd , thePacket, (size_t)theBytesToWrite); gpsd_report(4, "SendPacket(), wrote %d bytes\n", theBytesReturned); // Garmin says: // If the packet size was an exact multiple of the USB packet // size, we must make a final write call with no data // as a practical matter no known pckets are 64 bytes long so // this is untested // So here goes just in case if( 0 == (theBytesToWrite % ASYNC_DATA_SIZE) ) { char *n = ""; theBytesReturned = write( session->gpsdata.gps_fd , &n, 0); } } //----------------------------------------------------------------------------- // Gets a single packet. // this is odd, the garmin usb driver will only return 64 bytes, or less // at a time, no matter what you ask for. // // is you ask for less than 64 bytes then the next packet will include // just the remaining bytes of the last 64 byte packet. // // Reading a packet of length Zero, or less than 64, signals the end of // the entire packet. // // The Garmin sample WinXX code also assumes the same behavior, so // maybe it is something in the USB protocol. // // Return: 0 = got a good packet // -1 = error // 1 = got partial packet static int GetPacket (struct gps_device_t *session ) { struct timespec delay, rem; int cnt = 0; // int x = 0; // for debug dump memset( session->driver.garmin.Buffer, 0, sizeof(Packet_t)); memset( &delay, 0, sizeof(delay)); session->driver.garmin.BufferLen = 0; session->outbuflen = 0; gpsd_report(4, "GetPacket()\n"); //delay.tv_sec = 0; //delay.tv_nsec = 33300000L; //while (nanosleep(&delay, &rem) < 0) // continue; for( cnt = 0 ; cnt < 10 ; cnt++ ) { size_t pkt_size; // Read async data until the driver returns less than the // max async data size, which signifies the end of a packet // not optimal, but given the speed and packet nature of // the USB not too bad for a start ssize_t theBytesReturned = 0; uint8_t *buf = (uint8_t *)session->driver.garmin.Buffer; Packet_t *thePacket = (Packet_t*)buf; theBytesReturned = read(session->gpsdata.gps_fd , buf + session->driver.garmin.BufferLen , ASYNC_DATA_SIZE); // zero byte returned is a legal value and denotes the end of a // binary packet. if ( 0 > theBytesReturned ) { // read error... // or EAGAIN, but O_NONBLOCK is never set gpsd_report(0, "GetPacket() read error=%d, errno=%d\n" , theBytesReturned, errno); continue; } gpsd_report(5, "got %d bytes\n", theBytesReturned); session->driver.garmin.BufferLen += theBytesReturned; if ( 256 <= session->driver.garmin.BufferLen ) { // really bad read error... gpsd_report(3, "GetPacket() packet too long, %ld > 255 !\n" , session->driver.garmin.BufferLen); session->driver.garmin.BufferLen = 0; break; } pkt_size = 12 + get_int32((uint8_t*)&thePacket->mDataSize); if ( 12 <= session->driver.garmin.BufferLen) { // have enough data to check packet size if ( session->driver.garmin.BufferLen > pkt_size) { // wrong amount of data in buffer gpsd_report(3 , "GetPacket() packet size wrong! Packet: %ld, s/b %ld\n" , session->driver.garmin.BufferLen , pkt_size); session->driver.garmin.BufferLen = 0; break; } } if ( 64 > theBytesReturned ) { // zero length, or short, read is a flag for got the whole packet break; } /*@ ignore @*/ delay.tv_sec = 0; delay.tv_nsec = 3330000L; while (nanosleep(&delay, &rem) < 0) continue; /*@ end @*/ } // dump the individual bytes, debug only // for ( x = 0; x < session->driver.garmin.BufferLen; x++ ) { // gpsd_report(6, "p[%d] = %x\n", x, session->driver.garmin.Buffer[x]); // } if ( 10 <= cnt ) { gpsd_report(3, "GetPacket() packet too long or too slow!\n"); return -1; } gpsd_report(5, "GotPacket() sz=%d \n", session->driver.garmin.BufferLen); session->outbuflen = session->driver.garmin.BufferLen; return 0; } /* * garmin_probe() * * return 1 if garmin_gps device found * return 0 if not */ static bool garmin_probe(struct gps_device_t *session) { Packet_t *thePacket = NULL; uint8_t *buffer = NULL; fd_set fds, rfds; struct timeval tv; int sel_ret = 0; int ok = 0; int i; /* check for USB serial drivers -- very Linux-specific */ if (access("/sys/module/garmin_gps", R_OK) != 0) { gpsd_report(5, "garmin_gps not active.\n"); return false; } /* Save original terminal parameters */ if (tcgetattr(session->gpsdata.gps_fd,&session->ttyset_old) != 0) { gpsd_report(0, "garmin_probe: error getting port attributes: %s\n", strerror(errno)); return false; } memcpy(&session->ttyset,&session->ttyset_old,sizeof(session->ttyset)); (void)cfmakeraw(&session->ttyset); if (tcsetattr( session->gpsdata.gps_fd, TCIOFLUSH, &session->ttyset) < 0) { gpsd_report(0, "garmin_probe: error changing port attributes: %s\n", strerror(errno)); return false; } /* reset the buffer and buffer length */ memset( session->driver.garmin.Buffer, 0, sizeof(session->driver.garmin.Buffer) ); session->driver.garmin.BufferLen = 0; if (sizeof(session->driver.garmin.Buffer) < sizeof(Packet_t)) { gpsd_report(0, "garmin_probe: Compile error, garmin.Buffer too small.\n", strerror(errno)); return false; } buffer = (uint8_t *)session->driver.garmin.Buffer; thePacket = (Packet_t*)buffer; // set Mode 1, mode 0 is broken somewhere past 2.6.14 // but how? gpsd_report(3, "Set garmin_gps driver mode = 0\n"); Build_Send_Packet( session, GARMIN_LAYERID_PRIVATE , PRIV_PKTID_SET_MODE, 4, 0); // expect no return packet !? // get Version info gpsd_report(3, "Get garmin_gps driver version\n"); Build_Send_Packet(session, GARMIN_LAYERID_PRIVATE, PRIV_PKTID_INFO_REQ , 0, 0); /* get and print the driver Version info */ FD_ZERO(&fds); FD_SET(session->gpsdata.gps_fd, &fds); /* Wait, nicely, until the device returns the Version info * Toss any other packets, up to 4 */ ok = 0; memset( &tv,0,sizeof(tv)); for( i = 0 ; i < 4 ; i++ ) { memcpy((char *)&rfds, (char *)&fds, sizeof(rfds)); tv.tv_sec = 1; tv.tv_usec = 0; sel_ret = select(FD_SETSIZE, &rfds, NULL, NULL, &tv); if (sel_ret < 0) { if (errno == EINTR) continue; gpsd_report(0, "select: %s\n", strerror(errno)); return false; } else if ( sel_ret == 0 ) { gpsd_report(3, "garmin_probe() timeout, INFO_REQ\n"); // restore old terminal settings // TCIOFLUSH here causes gpsfake to hang, so skip that (void)tcsetattr(session->gpsdata.gps_fd, TCSANOW , &session->ttyset_old); return false; } if ( 0 == GetPacket( session ) ) { (void)PrintUSBPacket(session, thePacket); if( ( (uint8_t)75 == thePacket->mPacketType) && (PRIV_PKTID_INFO_RESP == thePacket->mPacketId) ) { ok = 1; break; } } } if ( 0 == ok ) { gpsd_report(2, "Garmin driver never answered to INFO_REQ.\n"); // restore old terminal settings (void)tcsetattr(session->gpsdata.gps_fd, TCIOFLUSH , &session->ttyset_old); return false; } /* depending on the GARMIN version, the device may spontaneously return the Product Capability here */ /* Tell the device that we are starting a session. */ gpsd_report(3, "Send Garmin Start Session\n"); Build_Send_Packet(session, GARMIN_LAYERID_TRANSPORT , GARMIN_PKTID_TRANSPORT_START_SESSION_REQ, 0, 0); /* Wait until the device is ready to the start the session * Toss any other packets, up to 4 */ ok = 0; for( i = 0 ; i < 4 ; i++ ) { memcpy((char *)&rfds, (char *)&fds, sizeof(rfds)); tv.tv_sec = 1; tv.tv_usec = 0; sel_ret = select(FD_SETSIZE, &rfds, NULL, NULL, &tv); if (sel_ret < 0) { if (errno == EINTR) continue; gpsd_report(0, "select: %s\n", strerror(errno)); return(0); } else if ( sel_ret == 0 ) { gpsd_report(3, "garmin_probe() timeout, START_SESSION\n"); // restore old terminal settings (void)tcsetattr(session->gpsdata.gps_fd, TCIOFLUSH , &session->ttyset_old); return(0); } if ( 0 == GetPacket( session ) ) { gpsd_report(3, "Got packet waiting for START_SESSION\n"); (void)PrintUSBPacket(session, thePacket); if( (GARMIN_LAYERID_TRANSPORT == thePacket->mPacketType) && (GARMIN_PKTID_TRANSPORT_START_SESSION_RESP == thePacket->mPacketId) ) { ok = 1; break; } } } if ( 0 == ok ) { gpsd_report(2, "Garmin driver never answered to START_SESSION.\n"); // restore old terminal settings (void)tcsetattr(session->gpsdata.gps_fd, TCIOFLUSH , &session->ttyset_old); return false; } // Tell the device to send product data gpsd_report(3, "Get Garmin Product Data\n"); Build_Send_Packet(session, GARMIN_LAYERID_APPL , GARMIN_PKTID_PRODUCT_RQST, 0, 0); // Get the product data packet // Toss any other packets, up to 4 ok = 0; for( i = 0 ; i < 4 ; i++ ) { memcpy((char *)&rfds, (char *)&fds, sizeof(rfds)); tv.tv_sec = 1; tv.tv_usec = 0; sel_ret = select(FD_SETSIZE, &rfds, NULL, NULL, &tv); if (sel_ret < 0) { if (errno == EINTR) continue; gpsd_report(0, "select: %s\n", strerror(errno)); return false; } else if ( sel_ret == 0 ) { gpsd_report(3, "garmin_probe() timeout, PRODUCT_DATA\n"); // restore old terminal settings (void)tcsetattr(session->gpsdata.gps_fd, TCIOFLUSH , &session->ttyset_old); return false; } if ( 0 == GetPacket( session ) ) { (void)PrintUSBPacket(session, thePacket); if( (GARMIN_LAYERID_APPL == (uint32_t)thePacket->mPacketType) && ( GARMIN_PKTID_PRODUCT_DATA == thePacket->mPacketId) ) { ok = 1; break; } } } if ( 0 == ok ) { gpsd_report(2, "Garmin driver never answered to PRODUCT_DATA.\n"); // restore old terminal settings (void)tcsetattr(session->gpsdata.gps_fd, TCIOFLUSH , &session->ttyset_old); return false; } return true; } /* * garmin_init() * * init a garmin_gps device, * session->gpsdata.gps_fd is assumed to already be open. * * the garmin_gps driver ignores all termios, baud rates, etc. so * any twiddling of that previously done is harmless. * */ static void garmin_init(struct gps_device_t *session) { bool ret; gpsd_report(5, "to garmin_probe()\n"); ret = garmin_probe( session ); /* FIXME - what if return code was bad */ /* FIXME - return code is always bad */ gpsd_report(3, "from garmin_probe() = %d\n", (int)ret); // turn on PVT data 49 gpsd_report(3, "Set Garmin to send reports every 1 second\n"); Build_Send_Packet(session, GARMIN_LAYERID_APPL , GARMIN_PKTID_L001_COMMAND_DATA, 2, CMND_START_PVT_DATA); // turn on RMD data 110 // Build_Send_Packet(session, GARMIN_LAYERID_APPL // , GARMIN_PKTID_L001_COMMAND_DATA, 2, CMND_START_RM_DATA); } static void garmin_close(struct gps_device_t *session UNUSED) { /* FIXME -- do we need to put the garmin to sleep? or is closing the port sufficient? */ gpsd_report(3, "garmin_close()\n"); return; } static ssize_t garmin_get_packet(struct gps_device_t *session) { return (ssize_t)( 0 == GetPacket( session ) ? 1 : 0); } static gps_mask_t garmin_usb_parse(struct gps_device_t *session) { gpsd_report(5, "garmin_usb_parse()\n"); return PrintUSBPacket(session, (Packet_t*)session->driver.garmin.Buffer); } /*@ +charint @*/ gps_mask_t garmin_ser_parse(struct gps_device_t *session) { unsigned char *buf = session->outbuffer; size_t len = session->outbuflen; unsigned char data_buf[MAX_BUFFER_SIZE]; unsigned char c; int i = 0; size_t n = 0; int data_index = 0; int got_dle = 0; unsigned char pkt_id = 0; unsigned char pkt_len = 0; unsigned char chksum = 0; gps_mask_t mask = 0; gpsd_report(5, "garmin_ser_parse()\n"); if ( 6 > len ) { /* WTF? */ /* minimum packet; [pkt id] [length=0] [chksum] */ gpsd_report(6, "Garmin serial too short: %#2x\n", len); return 0; } /* debug */ for ( i = 0 ; i < (int)len ; i++ ) { gpsd_report(6, "Char: %#02x\n", buf[i]); } if ( '\x10' != buf[0] ) { gpsd_report(6, "buf[0] not DLE\n", buf[0]); return 0; } n = 1; pkt_id = buf[n++]; chksum = pkt_id; if ( '\x10' == pkt_id ) { if ( '\x10' != buf[n++] ) { gpsd_report(6, "Bad pkt_id %#02x\n", pkt_id); return 0; } } pkt_len = buf[n++]; chksum += pkt_len; if ( '\x10' == pkt_len ) { if ( '\x10' != buf[n++] ) { gpsd_report(6, "Bad pkt_len %#02x\n", pkt_len); return 0; } } data_index = 0; for ( i = 0; i < 256 ; i++ ) { if ( (int)pkt_len == data_index ) { // got it all break; } if ( len < n + i ) { gpsd_report(6, "Packet too short %#02x < %#0x\n", len, n + i); return 0; } c = buf[n + i]; if ( got_dle ) { got_dle = 0; if ( '\x10' != c ) { gpsd_report(6, "Bad DLE %#02x\n", c); return 0; } } else { chksum += c; data_buf[ data_index++ ] = c; if ( '\x10' == c ) { got_dle = 1; } } } /* get checksum */ if ( len < n + i ) { gpsd_report(6, "No checksum, Packet too short %#02x < %#0x\n" , len, n + i); return 0; } c = buf[n + i++]; chksum += c; /* get final DLE */ if ( len < n + i ) { gpsd_report(6, "No final DLE, Packet too short %#02x < %#0x\n" , len, n + i); return 0; } c = buf[n + i++]; if ( '\x10' != c ) { gpsd_report(6, "Final DLE not DLE\n", c); return 0; } /* get final ETX */ if ( len < n + i ) { gpsd_report(6, "No final ETX, Packet too short %#02x < %#0x\n" , len, n + i); return 0; } c = buf[n + i++]; if ( '\x03' != c ) { gpsd_report(6, "Final ETX not ETX\n", c); return 0; } /* debug */ /*@ -usedef -compdef @*/ for ( i = 0 ; i < data_index ; i++ ) { gpsd_report(6, "Char: %#02x\n", data_buf[i]); } gpsd_report(4 , "garmin_ser_parse() Type: %#02x, Len: %#02x, chksum: %#02x\n" , pkt_id, pkt_len, chksum); mask = PrintSERPacket(session, pkt_id, pkt_len, data_buf); /*@ +usedef +compdef @*/ return mask; } /*@ -charint @*/ /* this is everything we export */ struct gps_type_t garmin_usb_binary = { .typename = "Garmin USB binary", /* full name of type */ .trigger = NULL, /* no trigger, it has a probe */ .channels = GARMIN_CHANNELS, /* consumer-grade GPS */ .wakeup = NULL, /* no wakeup to be done before hunt */ .probe = garmin_probe, /* how to detect at startup time */ .initializer = garmin_init, /* initialize the device */ .get_packet = garmin_get_packet,/* how to grab a packet */ .parse_packet = garmin_usb_parse, /* parse message packets */ .rtcm_writer = NULL, /* don't send DGPS corrections */ .speed_switcher = NULL, /* no speed switcher */ .mode_switcher = NULL, /* no mode switcher */ .rate_switcher = NULL, /* no sample-rate switcher */ .cycle_chars = -1, /* not relevant, no rate switch */ .wrapup = garmin_close, /* close hook */ .cycle = 1, /* updates every second */ }; struct gps_type_t garmin_ser_binary = { .typename = "Garmin Serial binary", /* full name of type */ .trigger = NULL, /* no trigger, it has a probe */ .channels = GARMIN_CHANNELS, /* consumer-grade GPS */ .wakeup = NULL, /* no wakeup to be done before hunt */ .probe = NULL, /* how to detect at startup time */ .initializer = NULL, /* initialize the device */ .get_packet = packet_get, /* how to grab a packet */ .parse_packet = garmin_ser_parse, /* parse message packets */ .rtcm_writer = NULL, /* don't send DGPS corrections */ .speed_switcher = NULL, /* no speed switcher */ .mode_switcher = NULL, /* no mode switcher */ .rate_switcher = NULL, /* no sample-rate switcher */ .cycle_chars = -1, /* not relevant, no rate switch */ .wrapup = NULL, /* close hook */ .cycle = 1, /* updates every second */ }; #endif /* GARMIN_ENABLE */