Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pin control updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.15 kernel cycle:

  Core:

   - The pin control Kconfig entry PINCTRL is now turned into a
     menuconfig option. This obviously has the implication of making the
     subsystem menu visible in menuconfig. This is happening because of
     two things:

      (a) Intel have started to deploy and depend on pin controllers in
          a way that is affecting users directly. This happens on the
          highly integrated laptop chipsets named after geographical
          places: baytrail, broxton, cannonlake, cedarfork, cherryview,
          denverton, geminilake, lewisburg, merrifield, sunrisepoint...
          It started a while back and now it is ever more evident that
          this is crucial infrastructure for x86 laptops and not an
          embedded obscurity anymore. Users need to be aware.

      (b) Pin control expanders on I2C and SPI that are arch-agnostic.
          Currently Semtech SX150X and Microchip MCP28x08 but more are
          expected. Users will have to be able to configure these in
          directly for their set-up.

   - Just go and select GPIOLIB now that we made sure that GPIOLIB is a
     very vanilla subsystem. Do not depend on it, if we need it, select
     it.

   - Exposing the pin control subsystem in menuconfig uncovered a bunch
     of obscure bugs that are now hopefully fixed, all more or less
     pertaining to Blackfin.

   - Unified namespace for cross-calls between pin control and GPIO.

   - New support for clock skew/delay generic DT bindings and generic
     pin config options for this.

   - Minor documentation improvements.

  Various:

   - The Renesas SH-PFC pin controller has evolved a lot. It seems
     Renesas are churning out new SoCs by the minute.

   - A bunch of non-critical fixes for the Rockchip driver.

   - Improve the use of library functions instead of open coding.

   - Support the MCP28018 variant in the MCP28x08 driver.

   - Static constifying"

* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
  pinctrl: gemini: Fix missing pad descriptions
  pinctrl: Add some depends on HAS_IOMEM
  pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
  pinctrl: gemini: Fix GMAC groups
  pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
  pinctrl: ti-iodelay: remove redundant unused variable dev
  pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
  pinctrl: gemini: Implement clock skew/delay config
  pinctrl: gemini: Use generic DT parser
  pinctrl: Add skew-delay pin config and bindings
  pinctrl: armada-37xx: Add edge both type gpio irq support
  pinctrl: uniphier: remove eMMC hardware reset pin-mux
  pinctrl: rockchip: Add iomux-route switching support for rk3288
  pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
  pinctrl: intel: Make offset to interrupt status register configurable
  pinctrl: sunxi: Enforce the strict mode by default
  pinctrl: sunxi: Disable strict mode for old pinctrl drivers
  pinctrl: sunxi: Introduce the strict flag
  pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
  pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
  ...

1 files changed, 0 insertions, 83 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
deleted file mode 100644
index c934106b10aa..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt
+++ /dev/null
@@ -1,83 +0,0 @@
-Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for
-8-/16-bit I/O expander with serial interface (I2C/SPI)
-
-Required properties:
-- compatible : Should be
-    - "mcp,mcp23s08" (DEPRECATED) for  8 GPIO SPI version
-    - "mcp,mcp23s17" (DEPRECATED) for 16 GPIO SPI version
-    - "mcp,mcp23008" (DEPRECATED) for  8 GPIO I2C version or
-    - "mcp,mcp23017" (DEPRECATED) for 16 GPIO I2C version of the chip
-
-    - "microchip,mcp23s08" for  8 GPIO SPI version
-    - "microchip,mcp23s17" for 16 GPIO SPI version
-    - "microchip,mcp23s18" for 16 GPIO SPI version
-    - "microchip,mcp23008" for  8 GPIO I2C version or
-    - "microchip,mcp23017" for 16 GPIO I2C version of the chip
-    NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
-    removed.
-- #gpio-cells : Should be two.
-  - first cell is the pin number
-  - second cell is used to specify flags. Flags are currently unused.
-- gpio-controller : Marks the device node as a GPIO controller.
-- reg : For an address on its bus. I2C uses this a the I2C address of the chip.
-        SPI uses this to specify the chipselect line which the chip is
-        connected to. The driver and the SPI variant of the chip support
-        multiple chips on the same chipselect. Have a look at
-        microchip,spi-present-mask below.
-
-Required device specific properties (only for SPI chips):
-- mcp,spi-present-mask (DEPRECATED)
-- microchip,spi-present-mask : This is a present flag, that makes only sense for SPI
-        chips - as the name suggests. Multiple SPI chips can share the same
-        SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a
-        chip connected with the corresponding spi address set. For example if
-        you have a chip with address 3 connected, you have to set bit3 to 1,
-        which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not
-        possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at
-        least one bit to 1 for SPI chips.
-    NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
-    removed.
-- spi-max-frequency = The maximum frequency this chip is able to handle
-
-Optional properties:
-- #interrupt-cells : Should be two.
-  - first cell is the pin number
-  - second cell is used to specify flags.
-- interrupt-controller: Marks the device node as a interrupt controller.
-
-Optional device specific properties:
-- microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices
-        with two interrupt outputs (these are the devices ending with 17 and
-        those that have 16 IOs) have two IO banks: IO 0-7 form bank 1 and
-        IO 8-15 are bank 2. These chips have two different interrupt outputs:
-        One for bank 1 and another for bank 2. If irq-mirror is set, both
-        interrupts are generated regardless of the bank that an input change
-        occurred on. If it is not set, the interrupt are only generated for the
-        bank they belong to.
-        On devices with only one interrupt output this property is useless.
-- microchip,irq-active-high: Sets the INTPOL flag in the IOCON register. This
-        configures the IRQ output polarity as active high.
-
-Example I2C (with interrupt):
-gpiom1: gpio@20 {
-        compatible = "microchip,mcp23017";
-        gpio-controller;
-        #gpio-cells = <2>;
-        reg = <0x20>;
-
-        interrupt-parent = <&gpio1>;
-        interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
-        interrupt-controller;
-        #interrupt-cells=<2>;
-        microchip,irq-mirror;
-};
-
-Example SPI:
-gpiom1: gpio@0 {
-        compatible = "microchip,mcp23s17";
-        gpio-controller;
-        #gpio-cells = <2>;
-        spi-present-mask = <0x01>;
-        reg = <0>;
-        spi-max-frequency = <1000000>;
-};