Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (44 commits)
  hwmon: Support for Dallas Semiconductor DS620
  hwmon: driver for Sensirion SHT21 humidity and temperature sensor
  hwmon: Add humidity attribute to sysfs ABI
  hwmon: sysfs ABI updates
  hwmon: (via-cputemp) sync hotplug handling with coretemp/pkgtemp
  hwmon: (lm95241) Rewrite to avoid using macros
  hwmon: (applesmc) Fix checkpatch errors and fix value range checks
  hwmon: (applesmc) Update copyright information
  hwmon: (applesmc) Silence driver
  hwmon: (applesmc) Simplify feature sysfs handling
  hwmon: (applesmc) Dynamic creation of fan files
  hwmon: (applesmc) Extract all features generically
  hwmon: (applesmc) Handle new temperature format
  hwmon: (applesmc) Dynamic creation of temperature files
  hwmon: (applesmc) Introduce a register lookup table
  hwmon: (applesmc) Use pr_fmt and pr_<level>
  hwmon: (applesmc) Relax the severity of device init failure
  hwmon: (applesmc) Add MacBookAir3,1(3,2) support
  hwmon: (w83627hf) Use pr_fmt and pr_<level>
  hwmon: (w83627ehf) Use pr_fmt and pr_<level>
  ...

3 files changed, 125 insertions, 7 deletions

diff --git a/Documentation/hwmon/ds620 b/Documentation/hwmon/ds620
new file mode 100644
index 000000000000..1fbe3cd916cc
--- /dev/null
+++ b/Documentation/hwmon/ds620
@@ -0,0 +1,34 @@
+Kernel driver ds620
+===================
+
+Supported chips:
+  * Dallas Semiconductor DS620
+    Prefix: 'ds620'
+    Datasheet: Publicly available at the Dallas Semiconductor website
+               http://www.dalsemi.com/
+
+Authors:
+        Roland Stigge <stigge@antcom.de>
+        based on ds1621.c by
+        Christian W. Zuckschwerdt <zany@triq.net>
+
+Description
+-----------
+
+The DS620 is a (one instance) digital thermometer and thermostat. It has both
+high and low temperature limits which can be user defined (i.e.  programmed
+into non-volatile on-chip registers). Temperature range is -55 degree Celsius
+to +125. Between 0 and 70 degree Celsius, accuracy is 0.5 Kelvin. The value
+returned via sysfs displays post decimal positions.
+
+The thermostat function works as follows: When configured via platform_data
+(struct ds620_platform_data) .pomode == 0 (default), the thermostat output pin
+PO is always low. If .pomode == 1, the thermostat is in PO_LOW mode. I.e., the
+output pin PO becomes active when the temperature falls below temp1_min and
+stays active until the temperature goes above temp1_max.
+
+Likewise, with .pomode == 2, the thermostat is in PO_HIGH mode. I.e., the PO
+output pin becomes active when the temperature goes above temp1_max and stays
+active until the temperature falls below temp1_min.
+
+The PO output pin of the DS620 operates active-low.
diff --git a/Documentation/hwmon/sht21 b/Documentation/hwmon/sht21
new file mode 100644
index 000000000000..db17fda45c3e
--- /dev/null
+++ b/Documentation/hwmon/sht21
@@ -0,0 +1,49 @@
+Kernel driver sht21
+===================
+
+Supported chips:
+  * Sensirion SHT21
+    Prefix: 'sht21'
+    Addresses scanned: none
+    Datasheet: Publicly available at the Sensirion website
+    http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT21.pdf
+
+  * Sensirion SHT25
+    Prefix: 'sht21'
+    Addresses scanned: none
+    Datasheet: Publicly available at the Sensirion website
+    http://www.sensirion.com/en/pdf/product_information/Datasheet-humidity-sensor-SHT25.pdf
+
+Author:
+  Urs Fleisch <urs.fleisch@sensirion.com>
+
+Description
+-----------
+
+The SHT21 and SHT25 are humidity and temperature sensors in a DFN package of
+only 3 x 3 mm footprint and 1.1 mm height. The difference between the two
+devices is the higher level of precision of the SHT25 (1.8% relative humidity,
+0.2 degree Celsius) compared with the SHT21 (2.0% relative humidity,
+0.3 degree Celsius).
+
+The devices communicate with the I2C protocol. All sensors are set to the same
+I2C address 0x40, so an entry with I2C_BOARD_INFO("sht21", 0x40) can be used
+in the board setup code.
+
+sysfs-Interface
+---------------
+
+temp1_input - temperature input
+humidity1_input - humidity input
+
+Notes
+-----
+
+The driver uses the default resolution settings of 12 bit for humidity and 14
+bit for temperature, which results in typical measurement times of 22 ms for
+humidity and 66 ms for temperature. To keep self heating below 0.1 degree
+Celsius, the device should not be active for more than 10% of the time,
+e.g. maximum two measurements per second at the given resolution.
+
+Different resolutions, the on-chip heater, using the CRC checksum and reading
+the serial number are not supported yet.
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index 645699010551..c6559f153589 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -384,10 +384,20 @@ curr[1-*]_min	Current min value.
 		Unit: milliampere
 		RW
 
+curr[1-*]_lcrit	Current critical low value
+		Unit: milliampere
+		RW
+
+curr[1-*]_crit	Current critical high value.
+		Unit: milliampere
+		RW
+
 curr[1-*]_input	Current input value
 		Unit: milliampere
 		RO
 
+Also see the Alarms section for status flags associated with currents.
+
 *********
 * Power *
 *********
@@ -450,13 +460,6 @@ power[1-*]_accuracy		Accuracy of the power meter.
 				Unit: Percent
 				RO
 
-power[1-*]_alarm		1 if the system is drawing more power than the
-				cap allows; 0 otherwise.  A poll notification is
-				sent to this file when the power use exceeds the
-				cap.  This file only appears if the cap is known
-				to be enforced by hardware.
-				RO
-
 power[1-*]_cap			If power use rises above this limit, the
 				system should take action to reduce power use.
 				A poll notification is sent to this file if the
@@ -479,6 +482,20 @@ power[1-*]_cap_min		Minimum cap that can be set.
 				Unit: microWatt
 				RO
 
+power[1-*]_max			Maximum power.
+				Unit: microWatt
+				RW
+
+power[1-*]_crit			Critical maximum power.
+				If power rises to or above this limit, the
+				system is expected take drastic action to reduce
+				power consumption, such as a system shutdown or
+				a forced powerdown of some devices.
+				Unit: microWatt
+				RW
+
+Also see the Alarms section for status flags associated with power readings.
+
 **********
 * Energy *
 **********
@@ -488,6 +505,15 @@ energy[1-*]_input		Cumulative energy use
 				RO
 
 
+************
+* Humidity *
+************
+
+humidity[1-*]_input		Humidity
+				Unit: milli-percent (per cent mille, pcm)
+				RO
+
+
 **********
 * Alarms *
 **********
@@ -501,6 +527,7 @@ implementation.
 
 in[0-*]_alarm
 curr[1-*]_alarm
+power[1-*]_alarm
 fan[1-*]_alarm
 temp[1-*]_alarm
 		Channel alarm
@@ -512,12 +539,20 @@ OR
 
 in[0-*]_min_alarm
 in[0-*]_max_alarm
+in[0-*]_lcrit_alarm
+in[0-*]_crit_alarm
 curr[1-*]_min_alarm
 curr[1-*]_max_alarm
+curr[1-*]_lcrit_alarm
+curr[1-*]_crit_alarm
+power[1-*]_cap_alarm
+power[1-*]_max_alarm
+power[1-*]_crit_alarm
 fan[1-*]_min_alarm
 fan[1-*]_max_alarm
 temp[1-*]_min_alarm
 temp[1-*]_max_alarm
+temp[1-*]_lcrit_alarm
 temp[1-*]_crit_alarm
 temp[1-*]_emergency_alarm
 		Limit alarm