Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next

Pull ARM SoC devicetree updates from Olof Johansson:
 "As with previous release, this continues to be among the largest
  branches we merge, with lots of new contents.

  New things for this release are among other things:

   - DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
   - Qualcomm APQ8064 and APQ8084 SoCs and eval boards
   - Nvidia Jetson TK1 development board (Tegra T124-based)

  Two new SoCs that didn't need enough new platform code to stand out
  enough for me to notice when writing the SoC tag, but that adds new DT
  contents are:

   - TI DRA72
   - Marvell Berlin 2Q"

* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
  ARM: dts: add secure firmware support for exynos5420-arndale-octa
  ARM: dts: add pmu sysreg node to exynos3250
  ARM: dts: correct the usb phy node in exynos5800-peach-pi
  ARM: dts: correct the usb phy node in exynos5420-peach-pit
  ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
  ARM: dts: add dts files for exynos3250 SoC
  ARM: dts: add mfc node for exynos5800
  ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
  ARM: dts: enable fimd for exynos5800-peach-pi
  ARM: dts: enable display controller for exynos5800-peach-pi
  ARM: dts: enable hdmi for exynos5800-peach-pi
  ARM: dts: add dts file for exynos5800-peach-pi board
  ARM: dts: add dts file for exynos5800 SoC
  ARM: dts: add dts file for exynos5260-xyref5260 board
  ARM: dts: add dts files for exynos5260 SoC
  ARM: dts: update watchdog node name in exynos5440
  ARM: dts: use key code macros on Origen and Arndale boards
  ARM: dts: enable RTC and WDT nodes on Origen boards
  ARM: dts: qcom: Add APQ8084-MTP board support
  ARM: dts: qcom: Add APQ8084 SoC support
  ...

1 files changed, 103 insertions, 2 deletions

diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 2836328b90c8..ad362c50e32e 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -138,6 +138,29 @@
 				0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
 			>;
 		};
+
+		qspi1_default: qspi1_default {
+			pinctrl-single,pins = <
+				0x7c (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x88 (PIN_INPUT_PULLUP | MUX_MODE2)
+				0x90 (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x94 (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x98 (PIN_INPUT_PULLUP | MUX_MODE3)
+				0x9c (PIN_INPUT_PULLUP | MUX_MODE3)
+			>;
+		};
+
+		pixcir_ts_pins: pixcir_ts_pins {
+			pinctrl-single,pins = <
+				0x44 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_a1.gpio1_17 */
+			>;
+		};
+
+		hdq_pins: pinmux_hdq_pins {
+			pinctrl-single,pins = <
+				0x234 (PIN_INPUT_PULLUP | MUX_MODE1)    /* cam1_wen.hdq_gpio */
+			>;
+		};
 	};
 
 	matrix_keypad: matrix_keypad@0 {
@@ -226,7 +249,9 @@
 	};
 
 	pixcir_ts@5c {
-		compatible = "pixcir,pixcir_ts";
+		compatible = "pixcir,pixcir_tangoc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pixcir_ts_pins>;
 		reg = <0x5c>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <17 0>;
@@ -234,7 +259,7 @@
 		attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
 
 		x-size = <1024>;
-		y-size = <768>;
+		y-size = <600>;
 	};
 };
 
@@ -367,3 +392,79 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 };
+
+&usb2_phy1 {
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb2_phy2 {
+	status = "okay";
+};
+
+&usb2 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi1_default>;
+
+	spi-max-frequency = <48000000>;
+	m25p80@0 {
+		compatible = "mx66l51235l";
+		spi-max-frequency = <48000000>;
+		reg = <0>;
+		spi-cpol;
+		spi-cpha;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* MTD partition table.
+		 * The ROM checks the first 512KiB
+		 * for a valid file to boot(XIP).
+		 */
+		partition@0 {
+			label = "QSPI.U_BOOT";
+			reg = <0x00000000 0x000080000>;
+		};
+		partition@1 {
+			label = "QSPI.U_BOOT.backup";
+			reg = <0x00080000 0x00080000>;
+		};
+		partition@2 {
+			label = "QSPI.U-BOOT-SPL_OS";
+			reg = <0x00100000 0x00010000>;
+		};
+		partition@3 {
+			label = "QSPI.U_BOOT_ENV";
+			reg = <0x00110000 0x00010000>;
+		};
+		partition@4 {
+			label = "QSPI.U-BOOT-ENV.backup";
+			reg = <0x00120000 0x00010000>;
+		};
+		partition@5 {
+			label = "QSPI.KERNEL";
+			reg = <0x00130000 0x0800000>;
+		};
+		partition@6 {
+			label = "QSPI.FILESYSTEM";
+			reg = <0x00930000 0x36D0000>;
+		};
+	};
+};
+
+&hdq {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdq_pins>;
+};