Blackfin serial driver: supporting BF548-EZKIT serial port

Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>

2 files changed, 117 insertions, 6 deletions

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 71a4ac53a7ef..2adbed4e10f3 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -599,7 +599,7 @@ config UART0_RTS_PIN
 
 config SERIAL_BFIN_UART1
 	bool "Enable UART1"
-	depends on SERIAL_BFIN && (BF534 || BF536 || BF537)
+	depends on SERIAL_BFIN && (BF534 || BF536 || BF537 || BF54x)
 	help
 	  Enable UART1
 
@@ -612,18 +612,58 @@ config BFIN_UART1_CTSRTS
 
 config UART1_CTS_PIN
 	int "UART1 CTS pin"
-	depends on BFIN_UART1_CTSRTS
+	depends on BFIN_UART1_CTSRTS && (BF53x || BF561)
 	default -1
 	help
 	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
 
 config UART1_RTS_PIN
 	int "UART1 RTS pin"
-	depends on BFIN_UART1_CTSRTS
+	depends on BFIN_UART1_CTSRTS && (BF53x || BF561)
 	default -1
 	help
 	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
 
+config SERIAL_BFIN_UART2
+	bool "Enable UART2"
+	depends on SERIAL_BFIN && (BF54x)
+	help
+	  Enable UART2
+
+config BFIN_UART2_CTSRTS
+	bool "Enable UART2 hardware flow control"
+	depends on SERIAL_BFIN_UART2
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART2_CTS_PIN
+	int "UART2 CTS pin"
+	depends on BFIN_UART2_CTSRTS
+	default -1
+	help
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART2_RTS_PIN
+	int "UART2 RTS pin"
+	depends on BFIN_UART2_CTSRTS
+	default -1
+	help
+	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART3
+	bool "Enable UART3"
+	depends on SERIAL_BFIN && (BF54x)
+	help
+	  Enable UART3
+
+config BFIN_UART3_CTSRTS
+	bool "Enable UART3 hardware flow control"
+	depends on SERIAL_BFIN_UART3
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
 config SERIAL_IMX
 	bool "IMX serial port support"
 	depends on ARM && ARCH_IMX
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index f7926dc7fa78..66c92bc36f3d 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -86,15 +86,29 @@ static void bfin_serial_stop_tx(struct uart_port *port)
 {
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
 
+#ifdef CONFIG_BF54x
+	while (!(UART_GET_LSR(uart) & TEMT))
+		continue;
+#endif
+
 #ifdef CONFIG_SERIAL_BFIN_DMA
 	disable_dma(uart->tx_dma_channel);
 #else
+#ifdef CONFIG_BF54x
+	/* Waiting for Transmission Finished */
+	while (!(UART_GET_LSR(uart) & TFI))
+		continue;
+	/* Clear TFI bit */
+	UART_PUT_LSR(uart, TFI);
+	UART_CLEAR_IER(uart, ETBEI);
+#else
 	unsigned short ier;
 
 	ier = UART_GET_IER(uart);
 	ier &= ~ETBEI;
 	UART_PUT_IER(uart, ier);
 #endif
+#endif
 }
 
 /*
@@ -107,12 +121,16 @@ static void bfin_serial_start_tx(struct uart_port *port)
 #ifdef CONFIG_SERIAL_BFIN_DMA
 	bfin_serial_dma_tx_chars(uart);
 #else
+#ifdef CONFIG_BF54x
+	UART_SET_IER(uart, ETBEI);
+#else
 	unsigned short ier;
 	ier = UART_GET_IER(uart);
 	ier |= ETBEI;
 	UART_PUT_IER(uart, ier);
 	bfin_serial_tx_chars(uart);
 #endif
+#endif
 }
 
 /*
@@ -121,6 +139,9 @@ static void bfin_serial_start_tx(struct uart_port *port)
 static void bfin_serial_stop_rx(struct uart_port *port)
 {
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+#ifdef CONFIG_BF54x
+	UART_CLEAR_IER(uart, ERBFI);
+#else
 	unsigned short ier;
 
 	ier = UART_GET_IER(uart);
@@ -129,6 +150,7 @@ static void bfin_serial_stop_rx(struct uart_port *port)
 #endif
 	ier &= ~ERBFI;
 	UART_PUT_IER(uart, ier);
+#endif
 }
 
 /*
@@ -325,10 +347,21 @@ static irqreturn_t bfin_serial_rx_int(int irq, void *dev_id)
 {
 	struct bfin_serial_port *uart = dev_id;
 
+#ifdef CONFIG_BF54x
+	unsigned short status;
+	spin_lock(&uart->port.lock);
+	status = UART_GET_LSR(uart);
+	while ((UART_GET_IER(uart) & ERBFI) && (status & DR)) {
+		bfin_serial_rx_chars(uart);
+		status = UART_GET_LSR(uart);
+	}
+	spin_unlock(&uart->port.lock);
+#else
 	spin_lock(&uart->port.lock);
 	while ((UART_GET_IIR(uart) & IIR_STATUS) == IIR_RX_READY)
 		bfin_serial_rx_chars(uart);
 	spin_unlock(&uart->port.lock);
+#endif
 	return IRQ_HANDLED;
 }
 
@@ -336,10 +369,21 @@ static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
 {
 	struct bfin_serial_port *uart = dev_id;
 
+#ifdef CONFIG_BF54x
+	unsigned short status;
+	spin_lock(&uart->port.lock);
+	status = UART_GET_LSR(uart);
+	while ((UART_GET_IER(uart) & ETBEI) && (status & THRE)) {
+		bfin_serial_tx_chars(uart);
+		status = UART_GET_LSR(uart);
+	}
+	spin_unlock(&uart->port.lock);
+#else
 	spin_lock(&uart->port.lock);
 	while ((UART_GET_IIR(uart) & IIR_STATUS) == IIR_TX_READY)
 		bfin_serial_tx_chars(uart);
 	spin_unlock(&uart->port.lock);
+#endif
 	return IRQ_HANDLED;
 }
 
@@ -350,7 +394,6 @@ static void bfin_serial_do_work(struct work_struct *work)
 
 	bfin_serial_mctrl_check(uart);
 }
-
 #endif
 
 #ifdef CONFIG_SERIAL_BFIN_DMA
@@ -399,9 +442,13 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
 	set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
 	set_dma_x_modify(uart->tx_dma_channel, 1);
 	enable_dma(uart->tx_dma_channel);
+#ifdef CONFIG_BF54x
+	UART_SET_IER(uart, ETBEI);
+#else
 	ier = UART_GET_IER(uart);
 	ier |= ETBEI;
 	UART_PUT_IER(uart, ier);
+#endif
 	spin_unlock_irqrestore(&uart->port.lock, flags);
 }
 
@@ -481,9 +528,13 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
 	if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
 		clear_dma_irqstat(uart->tx_dma_channel);
 		disable_dma(uart->tx_dma_channel);
+#ifdef CONFIG_BF54x
+		UART_CLEAR_IER(uart, ETBEI);
+#else
 		ier = UART_GET_IER(uart);
 		ier &= ~ETBEI;
 		UART_PUT_IER(uart, ier);
+#endif
 		xmit->tail = (xmit->tail+uart->tx_count) &(UART_XMIT_SIZE -1);
 		uart->port.icount.tx+=uart->tx_count;
 
@@ -665,7 +716,11 @@ static int bfin_serial_startup(struct uart_port *port)
 		return -EBUSY;
 	}
 #endif
+#ifdef CONFIG_BF54x
+	UART_SET_IER(uart, ERBFI);
+#else
 	UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
+#endif
 	return 0;
 }
 
@@ -756,29 +811,41 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	/* Disable UART */
 	ier = UART_GET_IER(uart);
+#ifdef CONFIG_BF54x
+	UART_CLEAR_IER(uart, 0xF);
+#else
 	UART_PUT_IER(uart, 0);
+#endif
 
+#ifndef CONFIG_BF54x
 	/* Set DLAB in LCR to Access DLL and DLH */
 	val = UART_GET_LCR(uart);
 	val |= DLAB;
 	UART_PUT_LCR(uart, val);
 	SSYNC();
+#endif
 
 	UART_PUT_DLL(uart, quot & 0xFF);
 	SSYNC();
 	UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
 	SSYNC();
 
+#ifndef CONFIG_BF54x
 	/* Clear DLAB in LCR to Access THR RBR IER */
 	val = UART_GET_LCR(uart);
 	val &= ~DLAB;
 	UART_PUT_LCR(uart, val);
 	SSYNC();
+#endif
 
 	UART_PUT_LCR(uart, lcr);
 
 	/* Enable UART */
+#ifdef CONFIG_BF54x
+	UART_SET_IER(uart, ier);
+#else
 	UART_PUT_IER(uart, ier);
+#endif
 
 	val = UART_GET_GCTL(uart);
 	val |= UCEN;
@@ -890,15 +957,15 @@ static void __init bfin_serial_init_ports(void)
 			bfin_serial_resource[i].uart_rts_pin;
 #endif
 		bfin_serial_hw_init(&bfin_serial_ports[i]);
-
 	}
+
 }
 
 #ifdef CONFIG_SERIAL_BFIN_CONSOLE
 static void bfin_serial_console_putchar(struct uart_port *port, int ch)
 {
 	struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
-	while (!(UART_GET_LSR(uart)))
+	while (!(UART_GET_LSR(uart) & THRE))
 		barrier();
 	UART_PUT_CHAR(uart, ch);
 	SSYNC();
@@ -950,18 +1017,22 @@ bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
 			case 2:	*bits = 7; break;
 			case 3:	*bits = 8; break;
 		}
+#ifndef CONFIG_BF54x
 		/* Set DLAB in LCR to Access DLL and DLH */
 		val = UART_GET_LCR(uart);
 		val |= DLAB;
 		UART_PUT_LCR(uart, val);
+#endif
 
 		dll = UART_GET_DLL(uart);
 		dlh = UART_GET_DLH(uart);
 
+#ifndef CONFIG_BF54x
 		/* Clear DLAB in LCR to Access THR RBR IER */
 		val = UART_GET_LCR(uart);
 		val &= ~DLAB;
 		UART_PUT_LCR(uart, val);
+#endif
 
 		*baud = get_sclk() / (16*(dll | dlh << 8));
 	}