diff options
Diffstat (limited to 'arch/mips/alchemy/devboards/pb1550.c')
| -rw-r--r-- | arch/mips/alchemy/devboards/pb1550.c | 244 |
1 files changed, 244 insertions, 0 deletions
diff --git a/arch/mips/alchemy/devboards/pb1550.c b/arch/mips/alchemy/devboards/pb1550.c new file mode 100644 index 000000000000..b37e7de8d920 --- /dev/null +++ b/arch/mips/alchemy/devboards/pb1550.c @@ -0,0 +1,244 @@ +/* + * Pb1550 board support. + * + * Copyright (C) 2009-2011 Manuel Lauss + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include <linux/dma-mapping.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <asm/mach-au1x00/au1000.h> +#include <asm/mach-au1x00/au1xxx_dbdma.h> +#include <asm/mach-au1x00/au1550nd.h> +#include <asm/mach-au1x00/gpio.h> +#include <asm/mach-db1x00/bcsr.h> +#include "platform.h" + +const char *get_system_type(void) +{ + return "PB1550"; +} + +void __init board_setup(void) +{ + u32 pin_func; + + bcsr_init(PB1550_BCSR_PHYS_ADDR, + PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS); + + alchemy_gpio2_enable(); + + /* + * Enable PSC1 SYNC for AC'97. Normaly done in audio driver, + * but it is board specific code, so put it here. + */ + pin_func = au_readl(SYS_PINFUNC); + au_sync(); + pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1; + au_writel(pin_func, SYS_PINFUNC); + + bcsr_write(BCSR_PCMCIA, 0); /* turn off PCMCIA power */ + + printk(KERN_INFO "AMD Alchemy Pb1550 Board\n"); +} + +/******************************************************************************/ + +static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin) +{ + if ((slot < 12) || (slot > 13) || pin == 0) + return -1; + if (slot == 12) { + switch (pin) { + case 1: return AU1500_PCI_INTB; + case 2: return AU1500_PCI_INTC; + case 3: return AU1500_PCI_INTD; + case 4: return AU1500_PCI_INTA; + } + } + if (slot == 13) { + switch (pin) { + case 1: return AU1500_PCI_INTA; + case 2: return AU1500_PCI_INTB; + case 3: return AU1500_PCI_INTC; + case 4: return AU1500_PCI_INTD; + } + } + return -1; +} + +static struct resource alchemy_pci_host_res[] = { + [0] = { + .start = AU1500_PCI_PHYS_ADDR, + .end = AU1500_PCI_PHYS_ADDR + 0xfff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct alchemy_pci_platdata pb1550_pci_pd = { + .board_map_irq = pb1550_map_pci_irq, +}; + +static struct platform_device pb1550_pci_host = { + .dev.platform_data = &pb1550_pci_pd, + .name = "alchemy-pci", + .id = 0, + .num_resources = ARRAY_SIZE(alchemy_pci_host_res), + .resource = alchemy_pci_host_res, +}; + +static struct resource au1550_psc2_res[] = { + [0] = { + .start = AU1550_PSC2_PHYS_ADDR, + .end = AU1550_PSC2_PHYS_ADDR + 0xfff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AU1550_PSC2_INT, + .end = AU1550_PSC2_INT, + .flags = IORESOURCE_IRQ, + }, + [2] = { + .start = AU1550_DSCR_CMD0_PSC2_TX, + .end = AU1550_DSCR_CMD0_PSC2_TX, + .flags = IORESOURCE_DMA, + }, + [3] = { + .start = AU1550_DSCR_CMD0_PSC2_RX, + .end = AU1550_DSCR_CMD0_PSC2_RX, + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device pb1550_i2c_dev = { + .name = "au1xpsc_smbus", + .id = 0, /* bus number */ + .num_resources = ARRAY_SIZE(au1550_psc2_res), + .resource = au1550_psc2_res, +}; + +static struct mtd_partition pb1550_nand_parts[] = { + [0] = { + .name = "NAND FS 0", + .offset = 0, + .size = 8 * 1024 * 1024, + }, + [1] = { + .name = "NAND FS 1", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + }, +}; + +static struct au1550nd_platdata pb1550_nand_pd = { + .parts = pb1550_nand_parts, + .num_parts = ARRAY_SIZE(pb1550_nand_parts), + .devwidth = 0, /* x8 NAND default, needs fixing up */ +}; + +static struct resource pb1550_nand_res[] = { + [0] = { + .start = 0x20000000, + .end = 0x20000fff, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device pb1550_nand_dev = { + .name = "au1550-nand", + .id = -1, + .resource = pb1550_nand_res, + .num_resources = ARRAY_SIZE(pb1550_nand_res), + .dev = { + .platform_data = &pb1550_nand_pd, + }, +}; + +static void __init pb1550_nand_setup(void) +{ + int boot_swapboot = (au_readl(MEM_STSTAT) & (0x7 << 1)) | + ((bcsr_read(BCSR_STATUS) >> 6) & 0x1); + + switch (boot_swapboot) { + case 0: + case 2: + case 8: + case 0xC: + case 0xD: + /* x16 NAND Flash */ + pb1550_nand_pd.devwidth = 1; + /* fallthrough */ + case 1: + case 9: + case 3: + case 0xE: + case 0xF: + /* x8 NAND, already set up */ + platform_device_register(&pb1550_nand_dev); + } +} + +static int __init pb1550_dev_init(void) +{ + int swapped; + + irq_set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW); + irq_set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW); + irq_set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH); + + /* enable both PCMCIA card irqs in the shared line */ + alchemy_gpio2_enable_int(201); + alchemy_gpio2_enable_int(202); + + /* Pb1550, like all others, also has statuschange irqs; however they're + * wired up on one of the Au1550's shared GPIO201_205 line, which also + * services the PCMCIA card interrupts. So we ignore statuschange and + * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia + * drivers are used to shared irqs and b) statuschange isn't really use- + * ful anyway. + */ + db1x_register_pcmcia_socket( + AU1000_PCMCIA_ATTR_PHYS_ADDR, + AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1, + AU1000_PCMCIA_MEM_PHYS_ADDR, + AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1, + AU1000_PCMCIA_IO_PHYS_ADDR, + AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1, + AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0); + + db1x_register_pcmcia_socket( + AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000, + AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1, + AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000, + AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1, + AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000, + AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1, + AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1); + + /* NAND setup */ + gpio_direction_input(206); /* GPIO206 high */ + pb1550_nand_setup(); + + swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT; + db1x_register_norflash(128 * 1024 * 1024, 4, swapped); + platform_device_register(&pb1550_pci_host); + platform_device_register(&pb1550_i2c_dev); + + return 0; +} +arch_initcall(pb1550_dev_init); |