diff options
Diffstat (limited to 'drivers/net/sfc/falcon_boards.c')
| -rw-r--r-- | drivers/net/sfc/falcon_boards.c | 203 |
1 files changed, 82 insertions, 121 deletions
diff --git a/drivers/net/sfc/falcon_boards.c b/drivers/net/sfc/falcon_boards.c index 3d950c2cf205..cfc6a5b5a477 100644 --- a/drivers/net/sfc/falcon_boards.c +++ b/drivers/net/sfc/falcon_boards.c @@ -26,7 +26,7 @@ /* Board types */ #define FALCON_BOARD_SFE4001 0x01 #define FALCON_BOARD_SFE4002 0x02 -#define FALCON_BOARD_SFN4111T 0x51 +#define FALCON_BOARD_SFE4003 0x03 #define FALCON_BOARD_SFN4112F 0x52 /* Board temperature is about 15°C above ambient when air flow is @@ -142,17 +142,17 @@ static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask) #endif /* CONFIG_SENSORS_LM87 */ /***************************************************************************** - * Support for the SFE4001 and SFN4111T NICs. + * Support for the SFE4001 NIC. * * The SFE4001 does not power-up fully at reset due to its high power * consumption. We control its power via a PCA9539 I/O expander. - * Both boards have a MAX6647 temperature monitor which we expose to + * It also has a MAX6647 temperature monitor which we expose to * the lm90 driver. * * This also provides minimal support for reflashing the PHY, which is * initiated by resetting it with the FLASH_CFG_1 pin pulled down. * On SFE4001 rev A2 and later this is connected to the 3V3X output of - * the IO-expander; on the SFN4111T it is connected to Falcon's GPIO3. + * the IO-expander. * We represent reflash mode as PHY_MODE_SPECIAL and make it mutually * exclusive with the network device being open. */ @@ -304,34 +304,6 @@ fail_on: return rc; } -static int sfn4111t_reset(struct efx_nic *efx) -{ - struct falcon_board *board = falcon_board(efx); - efx_oword_t reg; - - /* GPIO 3 and the GPIO register are shared with I2C, so block that */ - i2c_lock_adapter(&board->i2c_adap); - - /* Pull RST_N (GPIO 2) low then let it up again, setting the - * FLASH_CFG_1 strap (GPIO 3) appropriately. Only change the - * output enables; the output levels should always be 0 (low) - * and we rely on external pull-ups. */ - efx_reado(efx, ®, FR_AB_GPIO_CTL); - EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, true); - efx_writeo(efx, ®, FR_AB_GPIO_CTL); - msleep(1000); - EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, false); - EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO3_OEN, - !!(efx->phy_mode & PHY_MODE_SPECIAL)); - efx_writeo(efx, ®, FR_AB_GPIO_CTL); - msleep(1); - - i2c_unlock_adapter(&board->i2c_adap); - - ssleep(1); - return 0; -} - static ssize_t show_phy_flash_cfg(struct device *dev, struct device_attribute *attr, char *buf) { @@ -363,10 +335,7 @@ static ssize_t set_phy_flash_cfg(struct device *dev, efx->phy_mode = new_mode; if (new_mode & PHY_MODE_SPECIAL) falcon_stop_nic_stats(efx); - if (falcon_board(efx)->type->id == FALCON_BOARD_SFE4001) - err = sfe4001_poweron(efx); - else - err = sfn4111t_reset(efx); + err = sfe4001_poweron(efx); if (!err) err = efx_reconfigure_port(efx); if (!(new_mode & PHY_MODE_SPECIAL)) @@ -479,83 +448,6 @@ fail_hwmon: return rc; } -static int sfn4111t_check_hw(struct efx_nic *efx) -{ - s32 status; - - /* If XAUI link is up then do not monitor */ - if (EFX_WORKAROUND_7884(efx) && !efx->xmac_poll_required) - return 0; - - /* Test LHIGH, RHIGH, FAULT, EOT and IOT alarms */ - status = i2c_smbus_read_byte_data(falcon_board(efx)->hwmon_client, - MAX664X_REG_RSL); - if (status < 0) - return -EIO; - if (status & 0x57) - return -ERANGE; - return 0; -} - -static void sfn4111t_fini(struct efx_nic *efx) -{ - netif_info(efx, drv, efx->net_dev, "%s\n", __func__); - - device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); - i2c_unregister_device(falcon_board(efx)->hwmon_client); -} - -static struct i2c_board_info sfn4111t_a0_hwmon_info = { - I2C_BOARD_INFO("max6647", 0x4e), -}; - -static struct i2c_board_info sfn4111t_r5_hwmon_info = { - I2C_BOARD_INFO("max6646", 0x4d), -}; - -static void sfn4111t_init_phy(struct efx_nic *efx) -{ - if (!(efx->phy_mode & PHY_MODE_SPECIAL)) { - if (sft9001_wait_boot(efx) != -EINVAL) - return; - - efx->phy_mode = PHY_MODE_SPECIAL; - falcon_stop_nic_stats(efx); - } - - sfn4111t_reset(efx); - sft9001_wait_boot(efx); -} - -static int sfn4111t_init(struct efx_nic *efx) -{ - struct falcon_board *board = falcon_board(efx); - int rc; - - board->hwmon_client = - i2c_new_device(&board->i2c_adap, - (board->minor < 5) ? - &sfn4111t_a0_hwmon_info : - &sfn4111t_r5_hwmon_info); - if (!board->hwmon_client) - return -EIO; - - rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg); - if (rc) - goto fail_hwmon; - - if (efx->phy_mode & PHY_MODE_SPECIAL) - /* PHY may not generate a 156.25 MHz clock and MAC - * stats fetch will fail. */ - falcon_stop_nic_stats(efx); - - return 0; - -fail_hwmon: - i2c_unregister_device(board->hwmon_client); - return rc; -} - /***************************************************************************** * Support for the SFE4002 * @@ -691,6 +583,75 @@ static int sfn4112f_init(struct efx_nic *efx) return efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs); } +/***************************************************************************** + * Support for the SFE4003 + * + */ +static u8 sfe4003_lm87_channel = 0x03; /* use AIN not FAN inputs */ + +static const u8 sfe4003_lm87_regs[] = { + LM87_IN_LIMITS(0, 0x67, 0x7f), /* 2.5V: 1.5V +/- 10% */ + LM87_IN_LIMITS(1, 0x4c, 0x5e), /* Vccp1: 1.2V +/- 10% */ + LM87_IN_LIMITS(2, 0xac, 0xd4), /* 3.3V: 3.3V +/- 10% */ + LM87_IN_LIMITS(4, 0xac, 0xe0), /* 12V: 10.8-14V */ + LM87_IN_LIMITS(5, 0x3f, 0x4f), /* Vccp2: 1.0V +/- 10% */ + LM87_TEMP_INT_LIMITS(0, 70 + FALCON_BOARD_TEMP_BIAS), + 0 +}; + +static struct i2c_board_info sfe4003_hwmon_info = { + I2C_BOARD_INFO("lm87", 0x2e), + .platform_data = &sfe4003_lm87_channel, +}; + +/* Board-specific LED info. */ +#define SFE4003_RED_LED_GPIO 11 +#define SFE4003_LED_ON 1 +#define SFE4003_LED_OFF 0 + +static void sfe4003_set_id_led(struct efx_nic *efx, enum efx_led_mode mode) +{ + struct falcon_board *board = falcon_board(efx); + + /* The LEDs were not wired to GPIOs before A3 */ + if (board->minor < 3 && board->major == 0) + return; + + falcon_txc_set_gpio_val( + efx, SFE4003_RED_LED_GPIO, + (mode == EFX_LED_ON) ? SFE4003_LED_ON : SFE4003_LED_OFF); +} + +static void sfe4003_init_phy(struct efx_nic *efx) +{ + struct falcon_board *board = falcon_board(efx); + + /* The LEDs were not wired to GPIOs before A3 */ + if (board->minor < 3 && board->major == 0) + return; + + falcon_txc_set_gpio_dir(efx, SFE4003_RED_LED_GPIO, TXC_GPIO_DIR_OUTPUT); + falcon_txc_set_gpio_val(efx, SFE4003_RED_LED_GPIO, SFE4003_LED_OFF); +} + +static int sfe4003_check_hw(struct efx_nic *efx) +{ + struct falcon_board *board = falcon_board(efx); + + /* A0/A1/A2 board rev. 4003s report a temperature fault the whole time + * (bad sensor) so we mask it out. */ + unsigned alarm_mask = + (board->major == 0 && board->minor <= 2) ? + ~LM87_ALARM_TEMP_EXT1 : ~0; + + return efx_check_lm87(efx, alarm_mask); +} + +static int sfe4003_init(struct efx_nic *efx) +{ + return efx_init_lm87(efx, &sfe4003_hwmon_info, sfe4003_lm87_regs); +} + static const struct falcon_board_type board_types[] = { { .id = FALCON_BOARD_SFE4001, @@ -713,14 +674,14 @@ static const struct falcon_board_type board_types[] = { .monitor = sfe4002_check_hw, }, { - .id = FALCON_BOARD_SFN4111T, - .ref_model = "SFN4111T", - .gen_type = "100/1000/10GBASE-T adapter", - .init = sfn4111t_init, - .init_phy = sfn4111t_init_phy, - .fini = sfn4111t_fini, - .set_id_led = tenxpress_set_id_led, - .monitor = sfn4111t_check_hw, + .id = FALCON_BOARD_SFE4003, + .ref_model = "SFE4003", + .gen_type = "10GBASE-CX4 adapter", + .init = sfe4003_init, + .init_phy = sfe4003_init_phy, + .fini = efx_fini_lm87, + .set_id_led = sfe4003_set_id_led, + .monitor = sfe4003_check_hw, }, { .id = FALCON_BOARD_SFN4112F, |