summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
* ide: set drive->autotune in ide_pci_setup_ports()Bartlomiej Zolnierkiewicz2007-10-1929-74/+3
| | | | | | | | | | | | | | | | | | | | | | | Majority of host drivers using IDE PCI layer set drive->autotune, the only exceptions are: generic.c ns87415.c rz1000.c trm290.c * no ->set_pio_mode method it821x.c: * if memory allocation fails drive->autotune won't be set (but there also won't be ->set_pio_mode method in such case) piix.c: * MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method) However if there is no ->set_pio_mode method there are no changes in behavior w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* triflex: always tune PIOBartlomiej Zolnierkiewicz2007-10-191-0/+3
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* opti621: always tune PIOBartlomiej Zolnierkiewicz2007-10-191-4/+4
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cy82c693: always tune PIOBartlomiej Zolnierkiewicz2007-10-191-5/+5
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cs5520: always tune PIOBartlomiej Zolnierkiewicz2007-10-191-3/+4
| | | | | | | Since cs5520 uses VDMA best PIO mode was tuned anyway by ide_dma_check() but only if DMA was successfully initialized. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* alim15x3: always tune PIOBartlomiej Zolnierkiewicz2007-10-191-5/+5
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_LEGACY_IRQS host flagBartlomiej Zolnierkiewicz2007-10-197-35/+28
| | | | | | | | | | | | | Add IDE_HFLAG_LEGACY_IRQS host flag to tell ide_pci_setup_ports() to set hwif->irq to legacy IRQ 14/15 (iff hwif->irq is not already set) and convert atiixp, piix, serverworks, sis5513 and slc90e66 host drivers to use it. While at it: * In piix.c add IDE_HFLAGS_PIIX define and don't use ->init_hwif for MPIIX. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_SERIALIZE host flagBartlomiej Zolnierkiewicz2007-10-195-13/+16
| | | | | | | | Add IDE_HFLAG_SERIALIZE host flag to tell ide_pci_setup_ports() to set hwif/mate->serialized and convert aec62xx, cs5530 and sc1200 host drivers to use it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_ERROR_STOPS_FIFO host flagBartlomiej Zolnierkiewicz2007-10-194-8/+9
| | | | | | | | Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead of hwif->err_stops_fifo. As a side-effect this change fixes hwif->err_stops_fifo not being restored by ide_hwif_restore(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* piix: add DECLARE_ICH_DEV() macroBartlomiej Zolnierkiewicz2007-10-191-63/+47
| | | | | | | | | | | | | | | Add DECLARE_ICH_DEV() macro. While at it: * Add init_hwif_ich() (->init_hwif method) for ICH controllers. * Rename init_chipset_piix() to init_chipset_ich() and use it only for ICH controllers. * Remove no longer needed piix_is_ichx() helper. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_old: add DECLARE_PDC2026X_DEV() macroBartlomiej Zolnierkiewicz2007-10-191-41/+19
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_new: add DECLARE_PDCNEW_DEV() macroBartlomiej Zolnierkiewicz2007-10-191-57/+19
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* aec62xx: no need to disable UDMA in ->init_hwif method for ATP850UFBartlomiej Zolnierkiewicz2007-10-191-9/+5
| | | | | | | | | | * No need to disable UDMA in ->init_hwif method for ATP850UF (and since we now always tune PIO it will be disabled by ->set_pio_mode calls anyway). * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove .init_setup from ide_pci_device_tBartlomiej Zolnierkiewicz2007-10-191-1/+0
| | | | | | Now that all users were fixed we can safely remove it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* serverworks: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-191-31/+14
| | | | | | | | | | | | | | Merge init_setup_{svwks,csb6}() into svwks_init_one(). While at it: * Remove redundant dev->device checks. * Operate on a local copy of serverworks_chipsets[] entry. * Use pci_resource_start(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* scc_pata: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-191-2/+2
| | | | | Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_old: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-191-32/+25
| | | | | | | | * Split off pdc202ata4_fixup_irq() helper from init_setup_pdc202ata4(). * Merge init_setup_{pdc202ata4,pdc20265,pdc202xx}() into pdc202xx_init_one(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_new: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-191-59/+49
| | | | | | | | | | | | * Split off pdc20270_get_dev2() helper from init_setup_pdc20270(). * Merge init_setup_{pdcnew,pdc20270,pdc20276}() into pdc202new_init_one(). While at it: * Change KERN_ level of interrupt fixup message from KERN_WARNING to KERN_INFO. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt366: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-191-179/+127
| | | | | | | | | | | | | | | | | | | | | | | | | | | * Split off hpt{374,371,366}_init() helper from init_setup_hpt{374,371,366}(). * Merge init_setup_{374,372n,371,372a,302,366}() into hpt366_init_one(). While at it: * Use "HPT36x" name for HPT366/HPT368 chipsets. * Add .chip_name to struct hpt_info and use it to set set d->name. * Convert .max_ultra in struct hpt_info to .udma_mask and use it to set d->udma_mask. * Fix hpt302 to use HPT302_ALLOW_ATA133_6 define. * Change HPT366/HPT374 interrupt fixup message from KERN_WARNING to KERN_INFO. * Use the second hpt366_chipsets[] entry for HPT37x chipsets using HPT36x PCI device ID and fix .enablebits/.host_flags for HPT36x hpt366_chipsets[] entry. * Bump driver version. Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cmd64x: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-191-27/+12
| | | | | | | Merge init_setup_{cmd64x,cmd646}() into cmd64x_init_one(). Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* aec62xx: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-191-25/+14
| | | | | | | | | | | | | Merge init_setup_{aec62xx,aec6x80}() into aec62xx_init_one(). While at it: * Use id->driver_data instead of dev->device. * Use ATA_UDMA6 define. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: use I/O ops directly part #2 (take 2)Bartlomiej Zolnierkiewicz2007-10-194-37/+34
| | | | | | | | | v2: - bump host driver versions (as suggested by Sergei) - use I/O ops directly in drivers/ide/setup-pci.c Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: use pci_dev->revisionBartlomiej Zolnierkiewicz2007-10-194-27/+10
| | | | | | | | | | Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID so they were not converted by commit 44c10138fd4bbc4b6d6bff0873c24902f2a9da65. Cc: Auke Kok <auke-jan.h.kok@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cmd64x: Use dev->revisionAuke Kok2007-10-191-10/+4
| | | | | | Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* amd74xx: Omit PCI_REVISION_ID readAuke Kok2007-10-191-1/+0
| | | | | | Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ->mwdma_mask and ->swdma_mask to ide_pci_device_t (take 2)Bartlomiej Zolnierkiewicz2007-10-1932-177/+185
| | | | | | | | | | | | | | | | | | | | | | | * Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t. * Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif method may still override them). * Convert IDE PCI host drivers to use ide_pci_device_t DMA masks. While at it: * Use ATA_{UDMA,MWDMA,SWDMA}* defines. * hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345. * serverworks.c: fix DMA masks being set before checking DMA base. v2: * Add missing masks to DECLARE_GENERIC_PCI_DEV() macro. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_old: remove broken SWDMA supportBartlomiej Zolnierkiewicz2007-10-191-5/+1
| | | | | | | | Documentation doesn't mention SWDMA and moreover all timings used for SWDMA modes were over-clocked when compared to ATA spec. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_NO_LBA48 and IDE_HFLAG_NO_LBA48_DMA host flagsBartlomiej Zolnierkiewicz2007-10-196-11/+14
| | | | | | | | | Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma] and then remove no longer needed hwif->no_lba48[_dma]. As a side-effect this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore(). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove ->init_setup_dma from ide_pci_device_t (take 2)Bartlomiej Zolnierkiewicz2007-10-193-34/+20
| | | | | | | | | | | | | | | | | | | | | * Make ide_pci_device_t.host_flags u32 and add IDE_HFLAG_CS5520 host flag. * Pass ide_pci_device_t *d to setup-pci.c::ide_get_or_set_dma_base() and use d->name instead of hwif->cds->name. * Set IDE_HFLAG_CS5520 host flag in cs5520 host driver and use it in ide_get_or_set_dma_base() to find out which PCI BAR to use, remove no longer needed cs5520.c::cs5520_init_setup_dma() and ide_pci_device_t.init_setup_dma. This fixes PCI bus-mastering not being checked for CS5510/CS5520 hosts. v2: * It is wrong to check simplex bits on CS5510/CS5520 as v1 did. (Noticed by Alan). Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_NO_{DMA,AUTODMA} host flagsBartlomiej Zolnierkiewicz2007-10-1934-91/+30
| | | | | | | | Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using ide_pci_device_t to use these flags instead of d->autodma and then remove no longer needed d->autodma. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_BOOTABLE host flagBartlomiej Zolnierkiewicz2007-10-1934-136/+109
| | | | | | | | Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD} instead of d->bootable and then remove no longer needed d->bootable. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_NO_ATAPI_DMA host flagBartlomiej Zolnierkiewicz2007-10-1939-58/+40
| | | | | | | Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add DECLARE_GENERIC_PCI_DEV() macro to generic IDE PCI host driverBartlomiej Zolnierkiewicz2007-10-191-84/+29
| | | | | | | | | * Add DECLARE_GENERIC_PCI_DEV() macro to generic IDE PCI host driver and use it to cleanup generic_chipsets[]. * Remove dead/obsolete code while at it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* siimage: bump driver versionBartlomiej Zolnierkiewicz2007-10-191-1/+1
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: Fix cs5535 driver accessing beyond array boundaryBenjamin Herrenschmidt2007-10-191-1/+1
| | | | | | | | | | | | | | The cs5535 uses an incorrect construct to access the other drive of a pair, causing it to access beyond an array boundary on the secondary interface. This fixes it by using the new ide_get_paired_drive() helper instead. Bart: patch description fixes Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Andrew Morton <akpm@osdl.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: Fix siimage driver accessing beyond array boundaryBenjamin Herrenschmidt2007-10-191-1/+1
| | | | | | | | | | | | | | The siimage uses an incorrect construct to access the other drive of a pair, causing it to access beyond an array boundary on the secondary interface. This fixes it by using the new ide_get_paired_drive() helper instead. Bart: patch description fixes Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Andrew Morton <akpm@osdl.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: Add ide_get_paired_drive() helperBenjamin Herrenschmidt2007-10-191-0/+7
| | | | | | | | | | This adds a helper to get to the "other" drive on a pair connected to a given hwif. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Andrew Morton <akpm@osdl.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge branch 'release' of ↵Linus Torvalds2007-10-171-1/+3
|\ | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] fix non-numa build
| * [IA64] fix non-numa buildAndrew Morton2007-10-171-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | arch/ia64/kernel/machine_kexec.c: In function `arch_crash_save_vmcoreinfo': arch/ia64/kernel/machine_kexec.c:131: error: `pgdat_list' undeclared (first use in this function) arch/ia64/kernel/machine_kexec.c:131: error: (Each undeclared identifier is reported only once arch/ia64/kernel/machine_kexec.c:131: error: for each function it appears in.) arch/ia64/kernel/machine_kexec.c:134: error: `node_memblk' undeclared (first use in this function) arch/ia64/kernel/machine_kexec.c:135: error: `NR_NODE_MEMBLKS' undeclared (first use in this function) arch/ia64/kernel/machine_kexec.c:136: error: invalid application of `sizeof' to incomplete type `node_memblk_s' arch/ia64/kernel/machine_kexec.c:137: error: dereferencing pointer to incomplete type arch/ia64/kernel/machine_kexec.c:138: error: dereferencing pointer to incomplete type make[1]: *** [arch/ia64/kernel/machine_kexec.o] Error 1 Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
* | Merge branch 'for-linus' of ↵Linus Torvalds2007-10-1719-489/+689
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: 9p: remove sysctl 9p: fix bad kconfig cross-dependency 9p: soften invalidation in loose_mode 9p: attach-per-user 9p: rename uid and gid parameters 9p: define session flags 9p: Make transports dynamic
| * | 9p: remove sysctlEric Van Hensbergen2007-10-174-106/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A sysctl method was added to enable and disable debugging levels. After further review, it was decided that there are better approaches to doing this and the sysctl methodology isn't really desirable. This patch removes the sysctl code from 9p. Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
| * | 9p: fix bad kconfig cross-dependencyEric Van Hensbergen2007-10-175-46/+67
| | | | | | | | | | | | | | | | | | | | | | | | This patch moves transport dynamic registration and matching to the net module to prevent a bad Kconfig dependency between the net and fs 9p modules. Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
| * | 9p: soften invalidation in loose_modeEric Van Hensbergen2007-10-171-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Loose mode in 9p utilizes the page cache without respecting coherency with the server. Any writes previously invaldiated the entire mapping for a file. This patch softens the behavior to only invalidate the region of the actual write. Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
| * | 9p: attach-per-userLatchesar Ionkov2007-10-179-72/+247
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 9P2000 protocol requires the authentication and permission checks to be done in the file server. For that reason every user that accesses the file server tree has to authenticate and attach to the server separately. Multiple users can share the same connection to the server. Currently v9fs does a single attach and executes all I/O operations as a single user. This makes using v9fs in multiuser environment unsafe as it depends on the client doing the permission checking. This patch improves the 9P2000 support by allowing every user to attach separately. The patch defines three modes of access (new mount option 'access'): - attach-per-user (access=user) (default mode for 9P2000.u) If a user tries to access a file served by v9fs for the first time, v9fs sends an attach command to the server (Tattach) specifying the user. If the attach succeeds, the user can access the v9fs tree. As there is no uname->uid (string->integer) mapping yet, this mode works only with the 9P2000.u dialect. - allow only one user to access the tree (access=<uid>) Only the user with uid can access the v9fs tree. Other users that attempt to access it will get EPERM error. - do all operations as a single user (access=any) (default for 9P2000) V9fs does a single attach and all operations are done as a single user. If this mode is selected, the v9fs behavior is identical with the current one. Signed-off-by: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
| * | 9p: rename uid and gid parametersLatchesar Ionkov2007-10-174-14/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the names of 'uid' and 'gid' parameters to the more appropriate 'dfltuid' and 'dfltgid'. This also sets the default uid/gid to -2 (aka nfsnobody) Signed-off-by: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
| * | 9p: define session flagsLatchesar Ionkov2007-10-173-17/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | Create more general flags field in the v9fs_session_info struct and move the 'extended' flag as a bit in the flags. Signed-off-by: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
| * | 9p: Make transports dynamicEric Van Hensbergen2007-10-1712-285/+379
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch abstracts out the interfaces to underlying transports so that new transports can be added as modules. This should also allow kernel configuration of transports without ifdef-hell. Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
* | | Merge branch 'for-linus' of ↵Linus Torvalds2007-10-178-4/+1143
|\ \ \ | |_|/ |/| | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: net: libertas sdio driver mmc: at91_mci: cleanup: use MCI_ERRORS mmc: possible leak in mmc_read_ext_csd
| * | net: libertas sdio driverPierre Ossman2007-10-176-0/+1140
| | | | | | | | | | | | | | | | | | | | | Add driver for Marvell's Libertas 8385 and 8686 wifi chips. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Acked-by: Dan Williams <dcbw@redhat.com>
| * | mmc: at91_mci: cleanup: use MCI_ERRORSAndrew Victor2007-10-171-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A small MMC driver cleanup. Use the defined AT91_MCI_ERRORS in at91_mci_completed_command() instead of specifying all the error bits individually. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
View Lorry Controller Status