summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
* ipv6: export ip6_datagram_recv_ctlTom Parkin2013-01-311-0/+1
| | | | | | | | | | | ip6_datagram_recv_ctl and ip6_datagram_send_ctl are used for handling IPv6 ancillary data. Since ip6_datagram_send_ctl is already publicly exported for use in modules, ip6_datagram_recv_ctl should also be available to support ancillary data in the receive path. Signed-off-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: rename datagram_send_ctl and datagram_recv_ctlTom Parkin2013-01-318-32/+33
| | | | | | | | | | The datagram_*_ctl functions in net/ipv6/datagram.c are IPv6-specific. Since datagram_send_ctl is publicly exported it should be appropriately named to reflect the fact that it's for IPv6 only. Signed-off-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* NET: qmi_wwan: add Telit LE920 supportDaniele Palmas2013-01-301-0/+1
| | | | | | | | Add VID, PID and fixed interface for Telit LE920 Signed-off-by: Daniele Palmas <dnlplm@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6: do not create neighbor entries for local deliveryMarcelo Ricardo Leitner2013-01-301-1/+1
| | | | | | | | | | | | | | | They will be created at output, if ever needed. This avoids creating empty neighbor entries when TPROXYing/Forwarding packets for addresses that are not even directly reachable. Note that IPv4 already handles it this way. No neighbor entries are created for local input. Tested by myself and customer. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: usbnet: prevent buggy devices from killing usBjørn Mork2013-01-302-0/+27
| | | | | | | | | | | | | | | | A device sending 0 length frames as fast as it can has been observed killing the host system due to the resulting memory pressure. Temporarily disable RX skb allocation and URB submission when the current error ratio is high, preventing us from trying to allocate an infinite number of skbs. Reenable as soon as we are finished processing the done queue, allowing the device to continue working after short error bursts. Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* vmxnet3: set carrier state properly on probeNeil Horman2013-01-291-4/+3
| | | | | | | | | | | | | | | | | | | vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so /sys/class/net/<ifname>/operstate remains in the unknown state. Correct this by setting netif_carrier_off on probe, like other drivers do. Also, while we're at it, lets remove the netif_carrier_ok checks from the link_state_update function, as that check is atomically contained within the netif_carrier_[on|off] functions anyway Tested successfully by myself Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> CC: "VMware, Inc." <pv-drivers@vmware.com> CC: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: enable ECC on I217/I218 to catch packet buffer memory errorsBruce Allan2013-01-296-0/+71
| | | | | | | | | | | | | | | | | | | | | In rare instances, memory errors have been detected in the internal packet buffer memory on I217/I218 when stressed under certain environmental conditions. Enable Error Correcting Code (ECC) in hardware to catch both correctable and uncorrectable errors. Correctable errors will be handled by the hardware. Uncorrectable errors in the packet buffer will cause the packet to be received with an error indication in the buffer descriptor causing the packet to be discarded. If the uncorrectable error is in the descriptor itself, the hardware will stop and interrupt the driver indicating the error. The driver will then reset the hardware in order to clear the error and restart. Both types of errors will be accounted for in statistics counters. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: unset primary slave via sysfsMilos Vyletel2013-01-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When bonding module is loaded with primary parameter and one decides to unset primary slave using sysfs these settings are not preserved during bond device restart. Primary slave is only unset once and it's not remembered in bond->params structure. Below is example of recreation. grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond0 BONDING_OPTS="mode=active-backup miimon=100 primary=eth01" grep "Primary Slave" /proc/net/bonding/bond0 Primary Slave: eth01 (primary_reselect always) echo "" > /sys/class/net/bond0/bonding/primary grep "Primary Slave" /proc/net/bonding/bond0 Primary Slave: None sed -i -e 's/primary=eth01//' /etc/sysconfig/network-scripts/ifcfg-bond0 grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond BONDING_OPTS="mode=active-backup miimon=100 " ifdown bond0 && ifup bond0 without patch: grep "Primary Slave" /proc/net/bonding/bond0 Primary Slave: eth01 (primary_reselect always) with patch: grep "Primary Slave" /proc/net/bonding/bond0 Primary Slave: None Reviewed-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Milos Vyletel <milos.vyletel@sde.cz> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tcp: Increment LISTENOVERFLOW and LISTENDROPS in tcp_v4_conn_request()Nivedita Singhvi2013-01-291-1/+4
| | | | | | | | | | | | | | We drop a connection request if the accept backlog is full and there are sufficient packets in the syn queue to warrant starting drops. Increment the appropriate counters so this isn't silent, for accurate stats and help in debugging. This patch assumes LINUX_MIB_LISTENDROPS is a superset of/includes the counter LINUX_MIB_LISTENOVERFLOWS. Signed-off-by: Nivedita Singhvi <niv@us.ibm.com> Acked-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ipv6 addrconf: Fix interface identifiers of 802.15.4 devices.YOSHIFUJI Hideaki / 吉藤英明2013-01-291-0/+1
| | | | | | | | The "Universal/Local" (U/L) bit must be complmented according to RFC4944 and RFC2464. Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* be2net: Updating Module Author string and log message string to "Emulex ↵Sarveshwar Bandi2013-01-292-5/+5
| | | | | | | Corporation" Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tuntap: allow polling/writing/reading when detachedJason Wang2013-01-291-9/+16
| | | | | | | | | | | | | | | | | | | We forbid polling, writing and reading when the file were detached, this may complex the user in several cases: - when guest pass some buffers to vhost/qemu and then disable some queues, host/qemu needs to do its own cleanup on those buffers which is complex sometimes. We can do this simply by allowing a user can still write to an disabled queue. Write to an disabled queue will cause the packet pass to the kernel and read will get nothing. - align the polling behavior with macvtap which never fails when the queue is created. This can simplify the polling errors handling of its user (e.g vhost) We can simply achieve this by don't assign NULL to tfile->tun when detached. Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vhost_net: handle polling errors when setting backendJason Wang2013-01-293-13/+34
| | | | | | | | | | | | | | | | | | | | | | | Currently, the polling errors were ignored, which can lead following issues: - vhost remove itself unconditionally from waitqueue when stopping the poll, this may crash the kernel since the previous attempt of starting may fail to add itself to the waitqueue - userspace may think the backend were successfully set even when the polling failed. Solve this by: - check poll->wqh before trying to remove from waitqueue - report polling errors in vhost_poll_start(), tx_poll_start(), the return value will be checked and returned when userspace want to set the backend After this fix, there still could be a polling failure after backend is set, it will addressed by the next patch. Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* vhost_net: correct error handling in vhost_net_set_backend()Jason Wang2013-01-291-5/+11
| | | | | | | | | Currently, when vhost_init_used() fails the sock refcnt and ubufs were leaked. Correct this by calling vhost_init_used() before assign ubufs and restore the oldsock when it fails. Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tun: fix carrier on/off statusMichael S. Tsirkin2013-01-291-5/+8
| | | | | | | | | | | | | Commit c8d68e6be1c3b242f1c598595830890b65cea64a removed carrier off call from tun_detach since it's now called on queue disable and not only on tun close. This confuses userspace which used this flag to detect a free tun. To fix, put this back but under if (clean). Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Jason Wang <jasowang@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Tested-by: Toralf Förster <toralf.foerster@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* pktgen: correctly handle failures when adding a deviceCong Wang2013-01-291-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | The return value of pktgen_add_device() is not checked, so even if we fail to add some device, for example, non-exist one, we still see "OK:...". This patch fixes it. After this patch, I got: # echo "add_device non-exist" > /proc/net/pktgen/kpktgend_0 -bash: echo: write error: No such device # cat /proc/net/pktgen/kpktgend_0 Running: Stopped: Result: ERROR: can not add device non-exist # echo "add_device eth0" > /proc/net/pktgen/kpktgend_0 # cat /proc/net/pktgen/kpktgend_0 Running: Stopped: eth0 Result: OK: add_device=eth0 (Candidate for -stable) Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netem: fix delay calculation in rate extensionJohannes Naab2013-01-291-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The delay calculation with the rate extension introduces in v3.3 does not properly work, if other packets are still queued for transmission. For the delay calculation to work, both delay types (latency and delay introduces by rate limitation) have to be handled differently. The latency delay for a packet can overlap with the delay of other packets. The delay introduced by the rate however is separate, and can only start, once all other rate-introduced delays finished. Latency delay is from same distribution for each packet, rate delay depends on the packet size. .: latency delay -: rate delay x: additional delay we have to wait since another packet is currently transmitted .....---- Packet 1 .....xx------ Packet 2 .....------ Packet 3 ^^^^^ latency stacks ^^ rate delay doesn't stack ^^ latency stacks -----> time When a packet is enqueued, we first consider the latency delay. If other packets are already queued, we can reduce the latency delay until the last packet in the queue is send, however the latency delay cannot be <0, since this would mean that the rate is overcommitted. The new reference point is the time at which the last packet will be send. To find the time, when the packet should be send, the rate introduces delay has to be added on top of that. Signed-off-by: Johannes Naab <jn@stusta.de> Acked-by: Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* l2tp: prevent l2tp_tunnel_delete racing with userspace closeTom Parkin2013-01-292-12/+69
| | | | | | | | | | | | | | | | | | | | | If a tunnel socket is created by userspace, l2tp hooks the socket destructor in order to clean up resources if userspace closes the socket or crashes. It also caches a pointer to the struct sock for use in the data path and in the netlink interface. While it is safe to use the cached sock pointer in the data path, where the skb references keep the socket alive, it is not safe to use it elsewhere as such access introduces a race with userspace closing the socket. In particular, l2tp_tunnel_delete is prone to oopsing if a multithreaded userspace application closes a socket at the same time as sending a netlink delete command for the tunnel. This patch fixes this oops by forcing l2tp_tunnel_delete to explicitly look up a tunnel socket held by userspace using sockfd_lookup(). Signed-off-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'merge' of ↵Linus Torvalds2013-01-286-5/+33
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc Pull powerpc fixes from Benjamin Herrenschmidt: "Whenever you have a chance between two dives, you might want to consider pulling my merge branch to pickup a few fixes for 3.8 that have been accumulating for the last couple of weeks (I was myself travelling then on vacation). Nothing major, just a handful of powerpc bug fixes that I consider worth getting in before 3.8 goes final." And I'll have everybody know that I'm not diving for several days yet. Snif. * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc: Max next_tb to prevent from replaying timer interrupt powerpc: kernel/kgdb.c: Fix memory leakage powerpc/book3e: Disable interrupt after preempt_schedule_irq powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() function powerpc/pasemi: Fix crash on reboot powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32
| * powerpc: Max next_tb to prevent from replaying timer interruptTiejun Chen2013-01-291-2/+7
| | | | | | | | | | | | | | | | | | | | | | With lazy interrupt, we always call __check_irq_replaysome with decrementers_next_tb to check if we need to replay timer interrupt. So in hotplug case we also need to set decrementers_next_tb as MAX to make sure __check_irq_replay don't replay timer interrupt when return as we expect, otherwise we'll trap here infinitely. Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
| * powerpc: kernel/kgdb.c: Fix memory leakageCong Ding2013-01-291-2/+3
| | | | | | | | | | | | | | | | the variable backup_current_thread_info isn't freed before existing the function. Signed-off-by: Cong Ding <dinggnu@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
| * powerpc/book3e: Disable interrupt after preempt_schedule_irqTiejun Chen2013-01-291-0/+13
| | | | | | | | | | | | | | | | | | | | | | In preempt case current arch_local_irq_restore() from preempt_schedule_irq() may enable hard interrupt but we really should disable interrupts when we return from the interrupt, and so that we don't get interrupted after loading SRR0/1. Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com> CC: <stable@vger.kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
| * powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() functionCarl E. Love2013-01-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an error. The calculation is should be to shift left by (max_cntrs - cntr) times the width of the pmsel field width. However, the #define OPROFILE_MAX_PMC_NUM was used instead of OPROFILE_PMSEL_FIELD_WIDTH. This patch fixes the calculation. Signed-off-by: Carl Love <cel@us.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
| * powerpc/pasemi: Fix crash on rebootSteven Rostedt2013-01-291-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit f96972f2dc "kernel/sys.c: call disable_nonboot_cpus() in kernel_restart()" added a call to disable_nonboot_cpus() on kernel_restart(), which tries to shutdown all the CPUs except the first one. The issue with the PA Semi, is that it does not support CPU hotplug. When the call is made to __cpu_down(), it calls the notifiers CPU_DOWN_PREPARE, and then tries to take the CPU down. One of the notifiers to the CPU hotplug code, is the cpufreq. The DOWN_PREPARE will call __cpufreq_remove_dev() which calls cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O that is used by an interrupt that goes off constantly (system_reset_common, but it goes off during normal system operations too). I'm not sure exactly what this interrupt does. Running a simple function trace, you can see it goes off quite a bit: # tracer: function # # TASK-PID CPU# TIMESTAMP FUNCTION # | | | | | <idle>-0 [001] 1558.859363: .pasemi_system_reset_exception <-.system_reset_exception <idle>-0 [000] 1558.860112: .pasemi_system_reset_exception <-.system_reset_exception <idle>-0 [000] 1558.861109: .pasemi_system_reset_exception <-.system_reset_exception <idle>-0 [001] 1558.861361: .pasemi_system_reset_exception <-.system_reset_exception <idle>-0 [000] 1558.861437: .pasemi_system_reset_exception <-.system_reset_exception When the region is unmapped, the system crashes with: Disabling non-boot CPUs ... Error taking CPU1 down: -38 Unable to handle kernel paging request for data at address 0xd0000800903a0100 Faulting instruction address: 0xc000000000055fcc Oops: Kernel access of bad area, sig: 11 [#1] PREEMPT SMP NR_CPUS=64 NUMA PA Semi PWRficient Modules linked in: shpchp NIP: c000000000055fcc LR: c000000000055fb4 CTR: c0000000000df1fc REGS: c0000000012175d0 TRAP: 0300 Not tainted (3.8.0-rc4-test-dirty) MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 24000088 XER: 00000000 SOFTE: 0 DAR: d0000800903a0100, DSISR: 42000000 TASK = c0000000010e9008[0] 'swapper/0' THREAD: c000000001214000 CPU: 0 GPR00: d0000800903a0000 c000000001217850 c0000000012167e0 0000000000000000 GPR04: 0000000000000000 0000000000000724 0000000000000724 0000000000000000 GPR08: 0000000000000000 0000000000000000 0000000000000001 0000000000a70000 GPR12: 0000000024000080 c00000000fff0000 ffffffffffffffff 000000003ffffae0 GPR16: ffffffffffffffff 0000000000a21198 0000000000000060 0000000000000000 GPR20: 00000000008fdd35 0000000000a21258 000000003ffffaf0 0000000000000417 GPR24: 0000000000a226d0 c000000000000000 0000000000000000 0000000000000000 GPR28: c00000000138b358 0000000000000000 c000000001144818 d0000800903a0100 NIP [c000000000055fcc] .set_astate+0x5c/0xa4 LR [c000000000055fb4] .set_astate+0x44/0xa4 Call Trace: [c000000001217850] [c000000000055fb4] .set_astate+0x44/0xa4 (unreliable) [c0000000012178f0] [c00000000005647c] .restore_astate+0x2c/0x34 [c000000001217980] [c000000000054668] .pasemi_system_reset_exception+0x6c/0x88 [c000000001217a00] [c000000000019ef0] .system_reset_exception+0x48/0x84 [c000000001217a80] [c000000000001e40] system_reset_common+0x140/0x180 Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
| * powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32Li Zhong2013-01-291-0/+2
| | | | | | | | | | | | | | | | | | | | This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32, which is similar to commit 12660b17. Reported-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* | Merge tag 'md-3.8-fixes' of git://neil.brown.name/mdLinus Torvalds2013-01-282-64/+38
|\ \ | |/ |/| | | | | | | | | | | | | | | | | Pull dmraid fix from NeilBrown: "Just one fix for md in 3.8 dmraid assess redundancy and replacements slightly inaccurately which could lead to some degraded arrays failing to assemble." * tag 'md-3.8-fixes' of git://neil.brown.name/md: DM-RAID: Fix RAID10's check for sufficient redundancy
| * DM-RAID: Fix RAID10's check for sufficient redundancyJonathan Brassow2013-01-242-64/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Before attempting to activate a RAID array, it is checked for sufficient redundancy. That is, we make sure that there are not too many failed devices - or devices specified for rebuild - to undermine our ability to activate the array. The current code performs this check twice - once to ensure there were not too many devices specified for rebuild by the user ('validate_rebuild_devices') and again after possibly experiencing a failure to read the superblock ('analyse_superblocks'). Neither of these checks are sufficient. The first check is done properly but with insufficient information about the possible failure state of the devices to make a good determination if the array can be activated. The second check is simply done wrong in the case of RAID10 because it doesn't account for the independence of the stripes (i.e. mirror sets). The solution is to use the properly written check ('validate_rebuild_devices'), but perform the check after the superblocks have been read and we know which devices have failed. This gives us one check instead of two and performs it in a location where it can be done right. Only RAID10 was affected and it was affected in the following ways: - the code did not properly catch the condition where a user specified a device for rebuild that already had a failed device in the same mirror set. (This condition would, however, be caught at a deeper level in MD.) - the code triggers a false positive and denies activation when devices in independent mirror sets have failed - counting the failures as though they were all in the same set. The most likely place this error was introduced (or this patch should have been included) is in commit 4ec1e369 - first introduced in v3.7-rc1. Consequently this fix should also go in v3.7.y, however there is a small conflict on the .version in raid_target, so I'll submit a separate patch to -stable. Cc: stable@vger.kernel.org Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixesLinus Torvalds2013-01-281-1/+6
|\ \ | | | | | | | | | | | | | | | | | | Pull GFS2 fix from Steven Whitehouse. * git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes: GFS2: fix skip unlock condition
| * | GFS2: fix skip unlock conditionDavid Teigland2013-01-281-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | The recent commit fb6791d100d1bba20b5cdbc4912e1f7086ec60f8 included the wrong logic. The lvbptr check was incorrectly added after the patch was tested. Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
* | | Merge tag 'iommu-fixes-v3.8-rc5' of ↵Linus Torvalds2013-01-281-0/+34
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull IOMMU fix from Joerg Roedel: "One fix for the AMD IOMMU driver to work around broken BIOSes found in the field. Some BIOSes forget to enable a workaround for a hardware problem which might cause the IOMMU to stop working under high load conditions. The fix makes sure this workaround is enabled." * tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround
| * | | IOMMU, AMD Family15h Model10-1Fh erratum 746 WorkaroundSuravee Suthikulpanit2013-01-281-0/+34
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The IOMMU may stop processing page translations due to a perceived lack of credits for writing upstream peripheral page service request (PPR) or event logs. If the L2B miscellaneous clock gating feature is enabled the IOMMU does not properly register credits after the log request has completed, leading to a potential system hang. BIOSes are supposed to disable L2B micellaneous clock gating by setting L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This patch corrects that for those which do not enable this workaround. Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Acked-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Joerg Roedel <joro@8bytes.org>
* | | Merge tag 'mfd-for-linus-3.8-1' of ↵Linus Torvalds2013-01-2824-129/+314
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6 Pull MFD fixes from Samuel Ortiz: "This is the first pull request for MFD fixes for 3.8 We have some build failure fixes (twl4030, vexpress, abx500 and tps65910), some actual runtime oops and lockup fixes (rtsx, da9052), and some more hypothetical NULL pointers dereferences fixes for pcf50633 and max776xx. Then we also have additional rtsx fixes for a correct switch output voltage and clock divider correctness for rtl8411 (rtsx driver), and irqdomain fix for db8550-prcmu, and some more cosmetic fixes for arizona and wm5102." * tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed mfd: wm5102: Fix definition of WM5102_MAX_REGISTER mfd: twl4030: Don't warn about uninitialized return code mfd: da9052/53 lockup fix mfd: rtsx: Add clock divider hook mmc: rtsx: Call MFD hook to switch output voltage mfd: rtsx: Add output voltage switch hook mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM mfd: vexpress: Export global functions to fix build error mfd: arizona: Check errors from regcache_sync() mfd: tc3589x: Use simple irqdomain mfd: pcf50633: Init pcf->dev before using it mfd: max77693: Init max77693->dev before using it mfd: max77686: Init max77686->dev before using it mfd: db8500-prcmu: Fix irqdomain usage mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error mfd: arizona: Disable control interface reporting for WM5102 and WM5110
| * | | mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probedWei WANG2013-01-271-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event will point to NULL, and thus rtsx_pci_card_detect will reference a NULL pointer. Check card_event pointer before referencing it can avoid kernel panic. Signed-off-by: Wei WANG <wei_wang@realsil.com.cn> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: wm5102: Fix definition of WM5102_MAX_REGISTERMark Brown2013-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Updated in latest datasheet. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: twl4030: Don't warn about uninitialized return codeArnd Bergmann2013-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the twl4030_write_script function gets called with a zero length argument, its return value does not get set. We know that all scripts have a nonzero length, but returning an error in case they ever do is probably appropriate. Without this patch, building omap2plus_defconfig results in: drivers/mfd/twl4030-power.c: In function 'load_twl4030_script': drivers/mfd/twl4030-power.c:414:5: error: 'err' may be used uninitialized in this function Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: "Kristo, Tero" <t-kristo@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: da9052/53 lockup fixAshish Jangam2013-01-273-4/+126
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | An issue has been reported where the PMIC either locks up or fails to respond following a system Reset. This could result in a second write in which the bus writes the current content of the write buffer to address of the last I2C access. The failure case is where this unwanted write transfers incorrect data to a critical register. This patch fixes this issue to by following any read or write with a dummy read to a safe register address. A safe register address is one where the contents will not affect the operation of the system. Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: rtsx: Add clock divider hookWei WANG2013-01-276-2/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add callback function conv_clk_and_div_n to convert between SSC clock and its divider N. For rtl8411, the formula to calculate SSC clock divider N is different with the other card reader models. Signed-off-by: Wei WANG <wei_wang@realsil.com.cn> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mmc: rtsx: Call MFD hook to switch output voltageWei WANG2013-01-271-25/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Different card reader has different method to switch output voltage, so we have to use the callback function provided by MFD driver to switch output pad voltage. Signed-off-by: Wei WANG <wei_wang@realsil.com.cn> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: rtsx: Add output voltage switch hookWei WANG2013-01-275-4/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Different card reader has different method to switch output voltage, add this callback to let the card reader implement its individual switch function. This is needed as rtl8411 has a specific switch output voltage procedure. Signed-off-by: Wei WANG <wei_wang@realsil.com.cn> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: Fix compile errors and warnings when !CONFIG_AB8500_BMLee Jones2013-01-223-27/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: vexpress: Export global functions to fix build errorGuenter Roeck2013-01-221-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Compiling vexpress client drivers as module results in error messages such as ERROR: "__vexpress_config_func_get" [drivers/hwmon/vexpress.ko] undefined! ERROR: "vexpress_config_func_put" [drivers/hwmon/vexpress.ko] undefined! This is because the global functions in drivers/mfd/vexpress-config.c are not exported. Fix it. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: arizona: Check errors from regcache_sync()Mark Brown2013-01-221-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the control bus is unrelabile we may hit errors during regcache_sync(), especially given that it tends to be one the most dense bursts of I/O in many systems. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: tc3589x: Use simple irqdomainLinus Walleij2013-01-221-12/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a regression in the TC3589x driver introduced in commit 15e27b1088245a2de3b7d09d39cd209212eb16af "mfd: Provide the tc3589x with its own IRQ domain" If a system with a TC3589x expander is booted and a base IRQ is passed from platform data, a legacy domain will be used. However, since the Ux500 is now switched to use SPARSE_IRQ, no descriptors get allocated on-the-fly, and we get a crash. Fix this by switching to using the simple irqdomain that will handle this uniformly and also allocates descriptors explicitly. Also fix two small whitespace errors in the vicinity while we're at it. Cc: stable@kernel.org Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: pcf50633: Init pcf->dev before using itAxel Lin2013-01-221-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current code uses pcf->dev in the dev_err call before setting it to &client->dev. Fix it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: max77693: Init max77693->dev before using itAxel Lin2013-01-221-16/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current code uses max77693->dev in the dev_err call before setting it to &i2c->dev. Fix it. This patch also includes below cleanups: - Move checking pdata earlier and show dev_err if no platform data found. - Remove unnecessary err_regmap goto label. - Unregister i2c devices if regmap init for muic fails. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: max77686: Init max77686->dev before using itAxel Lin2013-01-221-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current code uses max77686->dev in the dev_err call before setting it to &i2c->dev. Fix it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: db8500-prcmu: Fix irqdomain usageLinus Walleij2013-01-221-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes two issues with the DB8500 PRCMU irqdomain: - You have to state the irq base 0 to get a linear domain for the DT case from irq_domain_add_simple() - The irqdomain was not used to translate the initial irq request using irq_create_mapping() making the linear case fail as it was lacking a proper descriptor. I took this opportunity to fix two lines of whitespace errors in related code as I was anyway messing around with it. Cc: stable@kernel.org Acked-by Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build errorAnilKumar Ch2013-01-221-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TPS65910 mfd driver uses functions that are only avaiable when REGMAP_IRQ is enabled. So "select REGMAP_IRQ" is added to mfd Kconfig to fix below build error: drivers/built-in.o: In function `tps65910_irq_exit': /media/anil/kernel/drivers/mfd/tps65910.c:265: undefined reference to `regmap_del_irq_chip' drivers/built-in.o: In function `tps65910_irq_init': /media/anil/kernel/drivers/mfd/tps65910.c:254: undefined reference to `regmap_add_irq_chip' drivers/built-in.o: In function `tps65910_i2c_probe': /media/anil/kernel/drivers/mfd/tps65910.c:509: undefined reference to `regmap_irq_get_domain' make: *** [vmlinux] Error 1 Signed-off-by: AnilKumar Ch <anilkumar@ti.com> Tested-by: Matt Porter <mporter@ti.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
| * | | mfd: arizona: Disable control interface reporting for WM5102 and WM5110Mark Brown2013-01-221-16/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rather than disabling the error reporting only for earlier revisions unconditionally disable it. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* | | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds2013-01-2897-418/+851
|\ \ \ \ | |_|/ / |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: "Much more accumulated than I would have liked due to an unexpected bout with a nasty flu: 1) AH and ESP input don't set ECN field correctly because the transport head of the SKB isn't set correctly, fix from Li RongQing. 2) If netfilter conntrack zones are disabled, we can return an uninitialized variable instead of the proper error code. Fix from Borislav Petkov. 3) Fix double SKB free in ath9k driver beacon handling, from Felix Feitkau. 4) Remove bogus assumption about netns cleanup ordering in nf_conntrack, from Pablo Neira Ayuso. 5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric Dumazet. It uses spin_is_locked() in it's test and is therefore unsuitable for UP. 6) Fix SELINUX labelling regressions added by the tuntap multiqueue changes, from Paul Moore. 7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin Nayak Sujir. 8) CXGB4 driver sets interrupt coalescing parameters only on first queue, rather than all of them. Fix from Thadeu Lima de Souza Cascardo. 9) Fix regression in the dispatch of read/write registers in dm9601 driver, from Tushar Behera. 10) ipv6_append_data miscalculates header length, from Romain KUNTZ. 11) Fix PMTU handling regressions on ipv4 routes, from Steffen Klassert, Timo Teräs, and Julian Anastasov. 12) In 3c574_cs driver, add necessary parenthesis to "x << y & z" expression. From Nickolai Zeldovich. 13) macvlan_get_size() causes underallocation netlink message space, fix from Eric Dumazet. 14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai Zeldovich. Amusingly the zero check was already there, we were just performing it after the modulus :-) 15) Some more splice bug fixes from Eric Dumazet, which fix things mostly eminating from how we now more aggressively use high-order pages in SKBs. 16) Fix size calculation bug when freeing hash tables in the IPSEC xfrm code, from Michal Kubecek. 17) Fix PMTU event propagation into socket cached routes, from Steffen Klassert. 18) Fix off by one in TX buffer release in netxen driver, from Eric Dumazet. 19) Fix rediculous memory allocation requirements introduced by the tuntap multiqueue changes, from Jason Wang. 20) Remove bogus AMD platform workaround in r8169 driver that causes major problems in normal operation, from Timo Teräs. 21) virtio-net set affinity and select queue don't handle discontiguous cpu numbers properly, fix from Wanlong Gao. 22) Fix a route refcounting issue in loopback driver, from Eric Dumazet. There's a similar fix coming that we might add to the macvlan driver as well. 23) Fix SKB leaks in batman-adv's distributed arp table code, from Matthias Schiffer. 24) r8169 driver gives descriptor ownership back the hardware before we're done reading the VLAN tag out of it, fix from Francois Romieu. 25) Checksums not calculated properly in GRE tunnel driver fix from Pravin B Shelar. 26) Fix SCTP memory leak on namespace exit." * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits) dm9601: support dm9620 variant SCTP: Free the per-net sysctl table on net exit. v2 net: phy: icplus: fix broken INTR pin settings net: phy: icplus: Use the RGMII interface mode to configure clock delays IP_GRE: Fix kernel panic in IP_GRE with GRE csum. sctp: set association state to established in dupcook_a handler ip6mr: limit IPv6 MRT_TABLE identifiers r8169: fix vlan tag read ordering. net: cdc_ncm: use IAD provided by the USB core batman-adv: filter ARP packets with invalid MAC addresses in DAT batman-adv: check for more types of invalid IP addresses in DAT batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply() net: loopback: fix a dst refcounting issue virtio-net: reset virtqueue affinity when doing cpu hotplug virtio-net: split out clean affinity function virtio-net: fix the set affinity bug when CPU IDs are not consecutive can: pch_can: fix invalid error codes can: ti_hecc: fix invalid error codes can: c_can: fix invalid error codes r8169: remove the obsolete and incorrect AMD workaround ...
View Lorry Controller Status