summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/at91-sama5d4_xplained.dts
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: at91: sama5d4_xplained: fix regulator namesAlexandre Belloni2016-07-151-2/+2
| | | | | | | | | | | vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a reg property. Remove their unit-address. Solves: Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
* ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulatorLudovic Desroches2016-03-221-0/+1
| | | | | | | | | | | If enabling the hsmci regulator on card detection, the board can reboot on sd card insertion. Keeping the regulator always enabled fixes this issue. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: 8d545f32bd77 ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies") Cc: stable@vger.kernel.org #4.3 and later Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ typeNicolas Ferre2016-01-271-1/+1
| | | | | | | | | For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of "edge falling". Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board") Cc: <stable@vger.kernel.org> # 4.1+
* ARM: dts: at91: sama5d4 xplained: properly mux phy interruptAlexandre Belloni2016-01-271-0/+6
| | | | | | | | | | | No interrupt were received from the phy because PIOE 1 may not be properly muxed. It prevented proper link detection, especially since commit 321beec5047a ("net: phy: Use interrupts when available in NOLINK state") disables polling. Cc: <stable@vger.kernel.org> # 4.4 Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: remove bootargsAlexandre Belloni2015-11-161-1/+0
| | | | | | | | | | Passing earlyprintk in the bootargs may crash the board as it depends on having a sane DEBUG_UART_PHYS configured which is not always the case. Also remove ignore_loglevel Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: remove leftovers clock definitionAlexandre Belloni2015-11-161-9/+0
| | | | | | | | The clocks group properties and the clock@0 node are useless, remove them to avoid copy pasting in future device trees. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: replace gpio-key,wakeup with wakeup-source propertySudeep Holla2015-11-161-1/+1
| | | | | | | | | | | | | | | | Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: sama5d4 xplained: enable the led D8Josh Wu2015-09-181-1/+1
| | | | | | | | | Enable D8 led as now the pioD is available. D8 is the power led and is on by default. Signed-off-by: Josh Wu <josh.wu@atmel.com> [nicolas.ferre@atmel.com: split the patch in 2] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: sama5d4: move ADC pinctrl to board device treesAlexandre Belloni2015-07-281-0/+9
| | | | | | | The ADC pinctrl is board specific, move it to the board device trees. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: sama5d4 xplained: use stdout-pathAlexandre Belloni2015-06-041-1/+2
| | | | | | | | Use stdout-path to specify the console and remove the console argument from the kernel command line. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 suppliesLudovic Desroches2015-05-191-0/+20
| | | | | | | | Add vcc_mmc1 fixed regulator to remove the 'no vmmc regulator found' warning when probing the mmc1 device. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: sama5d4 xplained: add spi1 on j14 connectorNicolas Ferre2015-05-191-0/+5
| | | | | | Route SPI1 on the Arduino "in the middle" spi connector. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: sama5d4 xplained: add i2c0Nicolas Ferre2015-03-041-0/+4
| | | | | | Add i2c0 aka twi0 on sama5d4 xplained board. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: sama5d4: add dts for sama5d4 xplained boardJosh Wu2015-03-041-0/+237
Add at91 sama5d4 xplained board support. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
View Lorry Controller Status