From 7a5063d86e95774ada66baac58fdfb7a80c75180 Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 22 Aug 2008 11:09:38 +0100 Subject: [ARM] pxa: introduce PXA_HAVE_BOARD_IRQS Signed-off-by: Russell King --- arch/arm/mach-pxa/Kconfig | 10 ++++++++++ arch/arm/mach-pxa/include/mach/irqs.h | 8 +------- 2 files changed, 11 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index e8ee7ec9ff6d..c9643bd4849c 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -38,16 +38,19 @@ config ARCH_LUBBOCK bool "Intel DBPXA250 Development Platform" select PXA25x select SA1111 + select PXA_HAVE_BOARD_IRQS config MACH_LOGICPD_PXA270 bool "LogicPD PXA270 Card Engine Development Platform" select PXA27x select HAVE_PWM + select PXA_HAVE_BOARD_IRQS config MACH_MAINSTONE bool "Intel HCDDBBVA0 Development Platform" select PXA27x select HAVE_PWM + select PXA_HAVE_BOARD_IRQS config ARCH_PXA_IDP bool "Accelent Xscale IDP" @@ -114,10 +117,12 @@ config MACH_TOSA bool "Enable Sharp SL-6000x (Tosa) Support" depends on PXA_SHARPSL select PXA25x + select PXA_HAVE_BOARD_IRQS config ARCH_PXA_ESERIES bool "PXA based Toshiba e-series PDAs" select PXA25x + select PXA_HAVE_BOARD_IRQS config MACH_E330 bool "Toshiba e330" @@ -215,12 +220,14 @@ config MACH_MAGICIAN bool "Enable HTC Magician Support" select PXA27x select IWMMXT + select PXA_HAVE_BOARD_IRQS config MACH_PCM027 bool "Phytec phyCORE-PXA270 CPU module (PCM-027)" select PXA27x select IWMMXT select PXA_SSP + select PXA_HAVE_BOARD_IRQS config ARCH_PXA_PALM bool "PXA based Palm PDAs" @@ -343,4 +350,7 @@ config TOSA_BT This is a simple driver that is able to control the state of built in bluetooth chip on tosa. +config PXA_HAVE_BOARD_IRQS + bool + endif diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h index 108b5db9b2af..ce3ce17ce3d3 100644 --- a/arch/arm/mach-pxa/include/mach/irqs.h +++ b/arch/arm/mach-pxa/include/mach/irqs.h @@ -178,13 +178,7 @@ #define NR_IRQS (IRQ_S1_BVD1_STSCHG + 1) #elif defined(CONFIG_SHARP_LOCOMO) #define NR_IRQS (IRQ_LOCOMO_SPI_TEND + 1) -#elif defined(CONFIG_ARCH_LUBBOCK) || \ - defined(CONFIG_MACH_LOGICPD_PXA270) || \ - defined(CONFIG_MACH_TOSA) || \ - defined(CONFIG_MACH_MAINSTONE) || \ - defined(CONFIG_MACH_PCM027) || \ - defined(CONFIG_ARCH_PXA_ESERIES) || \ - defined(CONFIG_MACH_MAGICIAN) +#elif defined(CONFIG_PXA_HAVE_BOARD_IRQS) #define NR_IRQS (IRQ_BOARD_END) #elif defined(CONFIG_MACH_ZYLONITE) #define NR_IRQS (IRQ_BOARD_START + 32) -- cgit v1.2.1 From 57a7a62eb65b35f51814382b0841ff99be242880 Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Mon, 1 Sep 2008 13:03:32 +0100 Subject: [ARM] 5233/1: Allow PXA to have ISA IRQs numbered 0-15 Allow PXA IRQs to be numbered starting at 16, leaving 0 to 15 for the ISA IRQs, if needed. This patch depends on RMK's PXA_HAVE_BOARD_IRQS patch. Signed-off-by: Marc Zyngier Acked-by: Russel King Acked-by: Eric Miao Signed-off-by: Russell King --- arch/arm/mach-pxa/Kconfig | 3 +++ arch/arm/mach-pxa/include/mach/entry-macro.S | 4 ++-- arch/arm/mach-pxa/include/mach/irqs.h | 11 +++++++++-- arch/arm/mach-pxa/irq.c | 2 +- 4 files changed, 15 insertions(+), 5 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index c9643bd4849c..b0417122d4e4 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -353,4 +353,7 @@ config TOSA_BT config PXA_HAVE_BOARD_IRQS bool +config PXA_HAVE_ISA_IRQS + bool + endif diff --git a/arch/arm/mach-pxa/include/mach/entry-macro.S b/arch/arm/mach-pxa/include/mach/entry-macro.S index de16c12d5232..f6b4bf3e73d2 100644 --- a/arch/arm/mach-pxa/include/mach/entry-macro.S +++ b/arch/arm/mach-pxa/include/mach/entry-macro.S @@ -41,7 +41,7 @@ and \irqstat, \irqstat, \irqnr clz \irqnr, \irqstat rsb \irqnr, \irqnr, #31 - add \irqnr, \irqnr, #32 + add \irqnr, \irqnr, #(32 + PXA_IRQ(0)) b 1001f 1003: mrc p6, 0, \irqstat, c0, c0, 0 @ ICIP @@ -52,6 +52,6 @@ rsb \irqstat, \irqnr, #0 and \irqstat, \irqstat, \irqnr clz \irqnr, \irqstat - rsb \irqnr, \irqnr, #31 + rsb \irqnr, \irqnr, #(31 + PXA_IRQ(0)) 1001: .endm diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h index ce3ce17ce3d3..9c163e19ada9 100644 --- a/arch/arm/mach-pxa/include/mach/irqs.h +++ b/arch/arm/mach-pxa/include/mach/irqs.h @@ -11,7 +11,14 @@ */ -#define PXA_IRQ(x) (x) +#ifdef CONFIG_PXA_HAVE_ISA_IRQS +#define PXA_ISA_IRQ(x) (x) +#define PXA_ISA_IRQ_NUM (16) +#else +#define PXA_ISA_IRQ_NUM (0) +#endif + +#define PXA_IRQ(x) (PXA_ISA_IRQ_NUM + (x)) #if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) #define IRQ_SSP3 PXA_IRQ(0) /* SSP3 service request */ @@ -73,7 +80,7 @@ #define IRQ_MMC3 PXA_IRQ(55) /* MMC3 Controller (PXA310) */ #endif -#define PXA_GPIO_IRQ_BASE (64) +#define PXA_GPIO_IRQ_BASE PXA_IRQ(64) #define PXA_GPIO_IRQ_NUM (128) #define GPIO_2_x_TO_IRQ(x) (PXA_GPIO_IRQ_BASE + (x)) diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c index 5e95c5372fec..fa69c3a6a38e 100644 --- a/arch/arm/mach-pxa/irq.c +++ b/arch/arm/mach-pxa/irq.c @@ -57,7 +57,7 @@ void __init pxa_init_irq(int irq_nr, set_wake_t fn) pxa_internal_irq_nr = irq_nr; - for (irq = 0; irq < irq_nr; irq += 32) { + for (irq = PXA_IRQ(0); irq < PXA_IRQ(irq_nr); irq += 32) { _ICMR(irq) = 0; /* disable all IRQs */ _ICLR(irq) = 0; /* all IRQs are IRQ, not FIQ */ } -- cgit v1.2.1 From 352699a3d7ccb027e0139a7a67931e7907af6249 Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Thu, 14 Aug 2008 17:20:31 +0200 Subject: Basic support for the Arcom/Eurotech Viper SBC. Signed-off-by: Marc Zyngier --- arch/arm/mach-pxa/Kconfig | 9 + arch/arm/mach-pxa/Makefile | 1 + arch/arm/mach-pxa/include/mach/viper.h | 96 ++++ arch/arm/mach-pxa/viper.c | 951 +++++++++++++++++++++++++++++++++ 4 files changed, 1057 insertions(+) create mode 100644 arch/arm/mach-pxa/include/mach/viper.h create mode 100644 arch/arm/mach-pxa/viper.c (limited to 'arch') diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig index b0417122d4e4..3ed5b2642c25 100644 --- a/arch/arm/mach-pxa/Kconfig +++ b/arch/arm/mach-pxa/Kconfig @@ -119,6 +119,15 @@ config MACH_TOSA select PXA25x select PXA_HAVE_BOARD_IRQS +config ARCH_VIPER + bool "Arcom/Eurotech VIPER SBC" + select PXA25x + select ISA + select I2C_GPIO + select HAVE_PWM + select PXA_HAVE_BOARD_IRQS + select PXA_HAVE_ISA_IRQS + config ARCH_PXA_ESERIES bool "PXA based Toshiba e-series PDAs" select PXA25x diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile index 99ecbe7f8506..c8a47ccec81e 100644 --- a/arch/arm/mach-pxa/Makefile +++ b/arch/arm/mach-pxa/Makefile @@ -43,6 +43,7 @@ obj-$(CONFIG_MACH_E750) += e750_lcd.o obj-$(CONFIG_MACH_E400) += e400_lcd.o obj-$(CONFIG_MACH_E800) += e800_lcd.o obj-$(CONFIG_MACH_PALMTX) += palmtx.o +obj-$(CONFIG_ARCH_VIPER) += viper.o ifeq ($(CONFIG_MACH_ZYLONITE),y) obj-y += zylonite.o diff --git a/arch/arm/mach-pxa/include/mach/viper.h b/arch/arm/mach-pxa/include/mach/viper.h new file mode 100644 index 000000000000..10988c270ca3 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/viper.h @@ -0,0 +1,96 @@ +/* + * arch/arm/mach-pxa/include/mach/viper.h + * + * Author: Ian Campbell + * Created: Feb 03, 2003 + * Copyright: Arcom Control Systems. + * + * Maintained by Marc Zyngier + * + * + * Created based on lubbock.h: + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef ARCH_VIPER_H +#define ARCH_VIPER_H + +#define VIPER_BOOT_PHYS PXA_CS0_PHYS +#define VIPER_FLASH_PHYS PXA_CS1_PHYS +#define VIPER_ETH_PHYS PXA_CS2_PHYS +#define VIPER_USB_PHYS PXA_CS3_PHYS +#define VIPER_ETH_DATA_PHYS PXA_CS4_PHYS +#define VIPER_CPLD_PHYS PXA_CS5_PHYS + +#define VIPER_CPLD_BASE (0xf0000000) +#define VIPER_PC104IO_BASE (0xf1000000) +#define VIPER_USB_BASE (0xf1800000) + +#define VIPER_ETH_GPIO (0) +#define VIPER_CPLD_GPIO (1) +#define VIPER_USB_GPIO (2) +#define VIPER_UARTA_GPIO (4) +#define VIPER_UARTB_GPIO (3) +#define VIPER_CF_CD_GPIO (32) +#define VIPER_CF_RDY_GPIO (8) +#define VIPER_BCKLIGHT_EN_GPIO (9) +#define VIPER_LCD_EN_GPIO (10) +#define VIPER_PSU_DATA_GPIO (6) +#define VIPER_PSU_CLK_GPIO (11) +#define VIPER_UART_SHDN_GPIO (12) +#define VIPER_BRIGHTNESS_GPIO (16) +#define VIPER_PSU_nCS_LD_GPIO (19) +#define VIPER_UPS_GPIO (20) +#define VIPER_CF_POWER_GPIO (82) +#define VIPER_TPM_I2C_SDA_GPIO (26) +#define VIPER_TPM_I2C_SCL_GPIO (27) +#define VIPER_RTC_I2C_SDA_GPIO (83) +#define VIPER_RTC_I2C_SCL_GPIO (84) + +#define VIPER_CPLD_P2V(x) ((x) - VIPER_CPLD_PHYS + VIPER_CPLD_BASE) +#define VIPER_CPLD_V2P(x) ((x) - VIPER_CPLD_BASE + VIPER_CPLD_PHYS) + +#ifndef __ASSEMBLY__ +# define __VIPER_CPLD_REG(x) (*((volatile u16 *)VIPER_CPLD_P2V(x))) +#endif + +/* board level registers in the CPLD: (offsets from CPLD_BASE) ... */ + +/* ... Physical addresses */ +#define _VIPER_LO_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100000) +#define _VIPER_ICR_PHYS (VIPER_CPLD_PHYS + 0x100002) +#define _VIPER_HI_IRQ_STATUS (VIPER_CPLD_PHYS + 0x100004) +#define _VIPER_VERSION_PHYS (VIPER_CPLD_PHYS + 0x100006) +#define VIPER_UARTA_PHYS (VIPER_CPLD_PHYS + 0x300010) +#define VIPER_UARTB_PHYS (VIPER_CPLD_PHYS + 0x300000) +#define _VIPER_SRAM_BASE (VIPER_CPLD_PHYS + 0x800000) + +/* ... Virtual addresses */ +#define VIPER_LO_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_LO_IRQ_STATUS) +#define VIPER_HI_IRQ_STATUS __VIPER_CPLD_REG(_VIPER_HI_IRQ_STATUS) +#define VIPER_VERSION __VIPER_CPLD_REG(_VIPER_VERSION_PHYS) +#define VIPER_ICR __VIPER_CPLD_REG(_VIPER_ICR_PHYS) + +/* Decode VIPER_VERSION register */ +#define VIPER_CPLD_REVISION(x) (((x) >> 5) & 0x7) +#define VIPER_BOARD_VERSION(x) (((x) >> 3) & 0x3) +#define VIPER_BOARD_ISSUE(x) (((x) >> 0) & 0x7) + +/* Interrupt and Configuration Register (VIPER_ICR) */ +/* This is a write only register. Only CF_RST is used under Linux */ + +extern void viper_cf_rst(int state); + +#define VIPER_ICR_RETRIG (1 << 0) +#define VIPER_ICR_AUTO_CLR (1 << 1) +#define VIPER_ICR_R_DIS (1 << 2) +#define VIPER_ICR_CF_RST (1 << 3) + +#endif + diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c new file mode 100644 index 000000000000..d7632f63603c --- /dev/null +++ b/arch/arm/mach-pxa/viper.c @@ -0,0 +1,951 @@ +/* + * linux/arch/arm/mach-pxa/viper.c + * + * Support for the Arcom VIPER SBC. + * + * Author: Ian Campbell + * Created: Feb 03, 2003 + * Copyright: Arcom Control Systems + * + * Maintained by Marc Zyngier + * + * + * Based on lubbock.c: + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include + +#include +#include +#include + +#include "generic.h" +#include "devices.h" + +static unsigned int icr; + +static void viper_icr_set_bit(unsigned int bit) +{ + icr |= bit; + VIPER_ICR = icr; +} + +static void viper_icr_clear_bit(unsigned int bit) +{ + icr &= ~bit; + VIPER_ICR = icr; +} + +/* This function is used from the pcmcia module to reset the CF */ +void viper_cf_rst(int state) +{ + if (state) + viper_icr_set_bit(VIPER_ICR_CF_RST); + else + viper_icr_clear_bit(VIPER_ICR_CF_RST); +} +EXPORT_SYMBOL(viper_cf_rst); + +/* + * The CPLD version register was not present on VIPER boards prior to + * v2i1. On v1 boards where the version register is not present we + * will just read back the previous value from the databus. + * + * Therefore we do two reads. The first time we write 0 to the + * (read-only) register before reading and the second time we write + * 0xff first. If the two reads do not match or they read back as 0xff + * or 0x00 then we have version 1 hardware. + */ +static u8 viper_hw_version(void) +{ + u8 v1, v2; + unsigned long flags; + + local_irq_save(flags); + + VIPER_VERSION = 0; + v1 = VIPER_VERSION; + VIPER_VERSION = 0xff; + v2 = VIPER_VERSION; + + v1 = (v1 != v2 || v1 == 0xff) ? 0 : v1; + + local_irq_restore(flags); + return v1; +} + +/* CPU sysdev */ +static int viper_cpu_suspend(struct sys_device *sysdev, pm_message_t state) +{ + viper_icr_set_bit(VIPER_ICR_R_DIS); + return 0; +} + +static int viper_cpu_resume(struct sys_device *sysdev) +{ + viper_icr_clear_bit(VIPER_ICR_R_DIS); + return 0; +} + +static struct sysdev_driver viper_cpu_sysdev_driver = { + .suspend = viper_cpu_suspend, + .resume = viper_cpu_resume, +}; + +static unsigned int current_voltage_divisor; + +/* + * If force is not true then step from existing to new divisor. If + * force is true then jump straight to the new divisor. Stepping is + * used because if the jump in voltage is too large, the VCC can dip + * too low and the regulator cuts out. + * + * force can be used to initialize the divisor to a know state by + * setting the value for the current clock speed, since we are already + * running at that speed we know the voltage should be pretty close so + * the jump won't be too large + */ +static void viper_set_core_cpu_voltage(unsigned long khz, int force) +{ + int i = 0; + unsigned int divisor = 0; + const char *v; + + if (khz < 200000) { + v = "1.0"; divisor = 0xfff; + } else if (khz < 300000) { + v = "1.1"; divisor = 0xde5; + } else { + v = "1.3"; divisor = 0x325; + } + + pr_debug("viper: setting CPU core voltage to %sV at %d.%03dMHz\n", + v, (int)khz / 1000, (int)khz % 1000); + +#define STEP 0x100 + do { + int step; + + if (force) + step = divisor; + else if (current_voltage_divisor < divisor - STEP) + step = current_voltage_divisor + STEP; + else if (current_voltage_divisor > divisor + STEP) + step = current_voltage_divisor - STEP; + else + step = divisor; + force = 0; + + gpio_set_value(VIPER_PSU_CLK_GPIO, 0); + gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 0); + + for (i = 1 << 11 ; i > 0 ; i >>= 1) { + udelay(1); + + gpio_set_value(VIPER_PSU_DATA_GPIO, step & i); + udelay(1); + + gpio_set_value(VIPER_PSU_CLK_GPIO, 1); + udelay(1); + + gpio_set_value(VIPER_PSU_CLK_GPIO, 0); + } + udelay(1); + + gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 1); + udelay(1); + + gpio_set_value(VIPER_PSU_nCS_LD_GPIO, 0); + + current_voltage_divisor = step; + } while (current_voltage_divisor != divisor); +} + +/* Interrupt handling */ +static unsigned long viper_irq_enabled_mask; + +static void viper_ack_irq(unsigned int irq) +{ + int viper_irq = irq - PXA_ISA_IRQ(0); + + if (viper_irq < 8) + VIPER_LO_IRQ_STATUS = 1 << viper_irq; + else + VIPER_HI_IRQ_STATUS = 1 << (viper_irq - 8); +} + +static void viper_mask_irq(unsigned int irq) +{ + viper_irq_enabled_mask &= ~(1 << (irq - PXA_ISA_IRQ(0))); +} + +static void viper_unmask_irq(unsigned int irq) +{ + viper_irq_enabled_mask |= (1 << (irq - PXA_ISA_IRQ(0))); +} + +static inline unsigned long viper_irq_pending(void) +{ + return (VIPER_HI_IRQ_STATUS << 8 | VIPER_LO_IRQ_STATUS) & + viper_irq_enabled_mask; +} + +static void viper_irq_handler(unsigned int irq, struct irq_desc *desc) +{ + unsigned long pending; + + pending = viper_irq_pending(); + do { + if (likely(pending)) { + irq = PXA_ISA_IRQ(0) + __ffs(pending); + generic_handle_irq(irq); + } + pending = viper_irq_pending(); + } while (pending); +} + +static struct irq_chip viper_irq_chip = { + .name = "ISA", + .ack = viper_ack_irq, + .mask = viper_mask_irq, + .unmask = viper_unmask_irq +}; + +static void __init viper_init_irq(void) +{ + const int isa_irqs[] = { 3, 4, 5, 6, 7, 10, 11, 12, 9, 14, 15 }; + int irq; + int isa_irq; + + pxa25x_init_irq(); + + /* setup ISA IRQs */ + for (irq = 0; irq < ARRAY_SIZE(isa_irqs); irq++) { + isa_irq = isa_irqs[irq]; + set_irq_chip(isa_irq, &viper_irq_chip); + set_irq_handler(isa_irq, handle_edge_irq); + set_irq_flags(isa_irq, IRQF_VALID | IRQF_PROBE); + } + + set_irq_chained_handler(gpio_to_irq(VIPER_CPLD_GPIO), + viper_irq_handler); + set_irq_type(gpio_to_irq(VIPER_CPLD_GPIO), IRQ_TYPE_EDGE_BOTH); + +#ifndef CONFIG_SERIAL_PXA + /* + * 8250 doesn't support IRQ_TYPE being passed as part + * of the plat_serial8250_port structure... + */ + set_irq_type(gpio_to_irq(VIPER_UARTA_GPIO), IRQ_TYPE_EDGE_RISING); + set_irq_type(gpio_to_irq(VIPER_UARTB_GPIO), IRQ_TYPE_EDGE_RISING); +#endif +} + +/* Flat Panel */ +static struct pxafb_mode_info fb_mode_info[] = { + { + .pixclock = 157500, + + .xres = 320, + .yres = 240, + + .bpp = 16, + + .hsync_len = 63, + .left_margin = 7, + .right_margin = 13, + + .vsync_len = 20, + .upper_margin = 0, + .lower_margin = 0, + + .sync = 0, + }, +}; + +static struct pxafb_mach_info fb_info = { + .modes = fb_mode_info, + .num_modes = 1, + .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL, +}; + +static int viper_backlight_init(struct device *dev) +{ + int ret; + + /* GPIO9 and 10 control FB backlight. Initialise to off */ + ret = gpio_request(VIPER_BCKLIGHT_EN_GPIO, "Backlight"); + if (ret) + goto err_request_bckl; + + ret = gpio_request(VIPER_LCD_EN_GPIO, "LCD"); + if (ret) + goto err_request_lcd; + + ret = gpio_direction_output(VIPER_BCKLIGHT_EN_GPIO, 0); + if (ret) + goto err_dir; + + ret = gpio_direction_output(VIPER_LCD_EN_GPIO, 0); + if (ret) + goto err_dir; + + return 0; + +err_dir: + gpio_free(VIPER_LCD_EN_GPIO); +err_request_lcd: + gpio_free(VIPER_BCKLIGHT_EN_GPIO); +err_request_bckl: + dev_err(dev, "Failed to setup LCD GPIOs\n"); + + return ret; +} + +static int viper_backlight_notify(int brightness) +{ + gpio_set_value(VIPER_LCD_EN_GPIO, !!brightness); + gpio_set_value(VIPER_BCKLIGHT_EN_GPIO, !!brightness); + + return brightness; +} + +static void viper_backlight_exit(struct device *dev) +{ + gpio_free(VIPER_LCD_EN_GPIO); + gpio_free(VIPER_BCKLIGHT_EN_GPIO); +} + +static struct platform_pwm_backlight_data viper_backlight_data = { + .pwm_id = 0, + .max_brightness = 100, + .dft_brightness = 100, + .pwm_period_ns = 1000000, + .init = viper_backlight_init, + .notify = viper_backlight_notify, + .exit = viper_backlight_exit, +}; + +static struct platform_device viper_backlight_device = { + .name = "pwm-backlight", + .dev = { + .parent = &pxa25x_device_pwm0.dev, + .platform_data = &viper_backlight_data, + }, +}; + +/* Ethernet */ +static struct resource smc91x_resources[] = { + [0] = { + .name = "smc91x-regs", + .start = VIPER_ETH_PHYS + 0x300, + .end = VIPER_ETH_PHYS + 0x30f, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = gpio_to_irq(VIPER_ETH_GPIO), + .end = gpio_to_irq(VIPER_ETH_GPIO), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + }, + [2] = { + .name = "smc91x-data32", + .start = VIPER_ETH_DATA_PHYS, + .end = VIPER_ETH_DATA_PHYS + 3, + .flags = IORESOURCE_MEM, + }, +}; + +static struct smc91x_platdata viper_smc91x_info = { + .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, + .leda = RPC_LED_100_10, + .ledb = RPC_LED_TX_RX, +}; + +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = -1, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, + .dev = { + .platform_data = &viper_smc91x_info, + }, +}; + +/* i2c */ +static struct i2c_gpio_platform_data i2c_bus_data = { + .sda_pin = VIPER_RTC_I2C_SDA_GPIO, + .scl_pin = VIPER_RTC_I2C_SCL_GPIO, + .udelay = 10, + .timeout = 100, +}; + +static struct platform_device i2c_bus_device = { + .name = "i2c-gpio", + .id = 1, /* pxa2xx-i2c is bus 0, so start at 1 */ + .dev = { + .platform_data = &i2c_bus_data, + } +}; + +static struct i2c_board_info __initdata viper_i2c_devices[] = { + { + I2C_BOARD_INFO("ds1338", 0x68), + }, +}; + +/* + * Serial configuration: + * You can either have the standard PXA ports driven by the PXA driver, + * or all the ports (PXA + 16850) driven by the 8250 driver. + * Choose your poison. + */ + +static struct resource viper_serial_resources[] = { +#ifndef CONFIG_SERIAL_PXA + { + .start = 0x40100000, + .end = 0x4010001f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x40200000, + .end = 0x4020001f, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x40700000, + .end = 0x4070001f, + .flags = IORESOURCE_MEM, + }, + { + .start = VIPER_UARTA_PHYS, + .end = VIPER_UARTA_PHYS + 0xf, + .flags = IORESOURCE_MEM, + }, + { + .start = VIPER_UARTB_PHYS, + .end = VIPER_UARTB_PHYS + 0xf, + .flags = IORESOURCE_MEM, + }, +#else + { + 0, + }, +#endif +}; + +static struct plat_serial8250_port serial_platform_data[] = { +#ifndef CONFIG_SERIAL_PXA + /* Internal UARTs */ + { + .membase = (void *)&FFUART, + .mapbase = __PREG(FFUART), + .irq = IRQ_FFUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { + .membase = (void *)&BTUART, + .mapbase = __PREG(BTUART), + .irq = IRQ_BTUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + { + .membase = (void *)&STUART, + .mapbase = __PREG(STUART), + .irq = IRQ_STUART, + .uartclk = 921600 * 16, + .regshift = 2, + .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST, + .iotype = UPIO_MEM, + }, + /* External UARTs */ + { + .mapbase = VIPER_UARTA_PHYS, + .irq = gpio_to_irq(VIPER_UARTA_GPIO), + .uartclk = 1843200, + .regshift = 1, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP | + UPF_SKIP_TEST, + }, + { + .mapbase = VIPER_UARTB_PHYS, + .irq = gpio_to_irq(VIPER_UARTB_GPIO), + .uartclk = 1843200, + .regshift = 1, + .iotype = UPIO_MEM, + .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP | + UPF_SKIP_TEST, + }, +#endif + { }, +}; + +static struct platform_device serial_device = { + .name = "serial8250", + .id = 0, + .dev = { + .platform_data = serial_platform_data, + }, + .num_resources = ARRAY_SIZE(viper_serial_resources), + .resource = viper_serial_resources, +}; + +/* USB */ +static void isp116x_delay(struct device *dev, int delay) +{ + ndelay(delay); +} + +static struct resource isp116x_resources[] = { + [0] = { /* DATA */ + .start = VIPER_USB_PHYS + 0, + .end = VIPER_USB_PHYS + 1, + .flags = IORESOURCE_MEM, + }, + [1] = { /* ADDR */ + .start = VIPER_USB_PHYS + 2, + .end = VIPER_USB_PHYS + 3, + .flags = IORESOURCE_MEM, + }, + [2] = { + .start = gpio_to_irq(VIPER_USB_GPIO), + .end = gpio_to_irq(VIPER_USB_GPIO), + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE, + }, +}; + +/* (DataBusWidth16|AnalogOCEnable|DREQOutputPolarity|DownstreamPort15KRSel ) */ +static struct isp116x_platform_data isp116x_platform_data = { + /* Enable internal resistors on downstream ports */ + .sel15Kres = 1, + /* On-chip overcurrent protection */ + .oc_enable = 1, + /* INT output polarity */ + .int_act_high = 1, + /* INT edge or level triggered */ + .int_edge_triggered = 0, + + /* WAKEUP pin connected - NOT SUPPORTED */ + /* .remote_wakeup_connected = 0, */ + /* Wakeup by devices on usb bus enabled */ + .remote_wakeup_enable = 0, + .delay = isp116x_delay, +}; + +static struct platform_device isp116x_device = { + .name = "isp116x-hcd", + .id = -1, + .num_resources = ARRAY_SIZE(isp116x_resources), + .resource = isp116x_resources, + .dev = { + .platform_data = &isp116x_platform_data, + }, + +}; + +/* MTD */ +static struct resource mtd_resources[] = { + [0] = { /* RedBoot config + filesystem flash */ + .start = VIPER_FLASH_PHYS, + .end = VIPER_FLASH_PHYS + SZ_32M - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { /* Boot flash */ + .start = VIPER_BOOT_PHYS, + .end = VIPER_BOOT_PHYS + SZ_1M - 1, + .flags = IORESOURCE_MEM, + }, + [2] = { /* + * SRAM size is actually 256KB, 8bits, with a sparse mapping + * (each byte is on a 16bit boundary). + */ + .start = _VIPER_SRAM_BASE, + .end = _VIPER_SRAM_BASE + SZ_512K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct mtd_partition viper_boot_flash_partition = { + .name = "RedBoot", + .size = SZ_1M, + .offset = 0, + .mask_flags = MTD_WRITEABLE, /* force R/O */ +}; + +static struct physmap_flash_data viper_flash_data[] = { + [0] = { + .width = 2, + .parts = NULL, + .nr_parts = 0, + }, + [1] = { + .width = 2, + .parts = &viper_boot_flash_partition, + .nr_parts = 1, + }, +}; + +static struct platform_device viper_mtd_devices[] = { + [0] = { + .name = "physmap-flash", + .id = 0, + .dev = { + .platform_data = &viper_flash_data[0], + }, + .resource = &mtd_resources[0], + .num_resources = 1, + }, + [1] = { + .name = "physmap-flash", + .id = 1, + .dev = { + .platform_data = &viper_flash_data[1], + }, + .resource = &mtd_resources[1], + .num_resources = 1, + }, +}; + +static struct platform_device *viper_devs[] __initdata = { + &smc91x_device, + &i2c_bus_device, + &serial_device, + &isp116x_device, + &viper_mtd_devices[0], + &viper_mtd_devices[1], + &viper_backlight_device, +}; + +static mfp_cfg_t viper_pin_config[] __initdata = { + /* Chip selects */ + GPIO15_nCS_1, + GPIO78_nCS_2, + GPIO79_nCS_3, + GPIO80_nCS_4, + GPIO33_nCS_5, + + /* FP Backlight */ + GPIO9_GPIO, /* VIPER_BCKLIGHT_EN_GPIO */ + GPIO10_GPIO, /* VIPER_LCD_EN_GPIO */ + GPIO16_PWM0_OUT, + + /* Ethernet PHY Ready */ + GPIO18_RDY, + + /* Serial shutdown */ + GPIO12_GPIO | MFP_LPM_DRIVE_HIGH, /* VIPER_UART_SHDN_GPIO */ + + /* Compact-Flash / PC104 */ + GPIO48_nPOE, + GPIO49_nPWE, + GPIO50_nPIOR, + GPIO51_nPIOW, + GPIO52_nPCE_1, + GPIO53_nPCE_2, + GPIO54_nPSKTSEL, + GPIO55_nPREG, + GPIO56_nPWAIT, + GPIO57_nIOIS16, + GPIO8_GPIO, /* VIPER_CF_RDY_GPIO */ + GPIO32_GPIO, /* VIPER_CF_CD_GPIO */ + GPIO82_GPIO, /* VIPER_CF_POWER_GPIO */ + + /* Integrated UPS control */ + GPIO20_GPIO, /* VIPER_UPS_GPIO */ + + /* Vcc regulator control */ + GPIO6_GPIO, /* VIPER_PSU_DATA_GPIO */ + GPIO11_GPIO, /* VIPER_PSU_CLK_GPIO */ + GPIO19_GPIO, /* VIPER_PSU_nCS_LD_GPIO */ + + /* i2c busses */ + GPIO26_GPIO, /* VIPER_TPM_I2C_SDA_GPIO */ + GPIO27_GPIO, /* VIPER_TPM_I2C_SCL_GPIO */ + GPIO83_GPIO, /* VIPER_RTC_I2C_SDA_GPIO */ + GPIO84_GPIO, /* VIPER_RTC_I2C_SCL_GPIO */ + + /* PC/104 Interrupt */ + GPIO1_GPIO | WAKEUP_ON_EDGE_RISE, /* VIPER_CPLD_GPIO */ +}; + +static unsigned long viper_tpm; + +static int __init viper_tpm_setup(char *str) +{ + strict_strtoul(str, 10, &viper_tpm); + return 1; +} + +__setup("tpm=", viper_tpm_setup); + +static void __init viper_tpm_init(void) +{ + struct platform_device *tpm_device; + struct i2c_gpio_platform_data i2c_tpm_data = { + .sda_pin = VIPER_TPM_I2C_SDA_GPIO, + .scl_pin = VIPER_TPM_I2C_SCL_GPIO, + .udelay = 10, + .timeout = 100, + }; + char *errstr; + + /* Allocate TPM i2c bus if requested */ + if (!viper_tpm) + return; + + tpm_device = platform_device_alloc("i2c-gpio", 2); + if (tpm_device) { + if (!platform_device_add_data(tpm_device, + &i2c_tpm_data, + sizeof(i2c_tpm_data))) { + if (platform_device_add(tpm_device)) { + errstr = "register TPM i2c bus"; + goto error_free_tpm; + } + } else { + errstr = "allocate TPM i2c bus data"; + goto error_free_tpm; + } + } else { + errstr = "allocate TPM i2c device"; + goto error_tpm; + } + + return; + +error_free_tpm: + kfree(tpm_device); +error_tpm: + pr_err("viper: Couldn't %s, giving up\n", errstr); +} + +static void __init viper_init_vcore_gpios(void) +{ + if (gpio_request(VIPER_PSU_DATA_GPIO, "PSU data")) + goto err_request_data; + + if (gpio_request(VIPER_PSU_CLK_GPIO, "PSU clock")) + goto err_request_clk; + + if (gpio_request(VIPER_PSU_nCS_LD_GPIO, "PSU cs")) + goto err_request_cs; + + if (gpio_direction_output(VIPER_PSU_DATA_GPIO, 0) || + gpio_direction_output(VIPER_PSU_CLK_GPIO, 0) || + gpio_direction_output(VIPER_PSU_nCS_LD_GPIO, 0)) + goto err_dir; + + /* c/should assume redboot set the correct level ??? */ + viper_set_core_cpu_voltage(get_clk_frequency_khz(0), 1); + + return; + +err_dir: + gpio_free(VIPER_PSU_nCS_LD_GPIO); +err_request_cs: + gpio_free(VIPER_PSU_CLK_GPIO); +err_request_clk: + gpio_free(VIPER_PSU_DATA_GPIO); +err_request_data: + pr_err("viper: Failed to setup vcore control GPIOs\n"); +} + +static void __init viper_init_serial_gpio(void) +{ + if (gpio_request(VIPER_UART_SHDN_GPIO, "UARTs shutdown")) + goto err_request; + + if (gpio_direction_output(VIPER_UART_SHDN_GPIO, 0)) + goto err_dir; + + return; + +err_dir: + gpio_free(VIPER_UART_SHDN_GPIO); +err_request: + pr_err("viper: Failed to setup UART shutdown GPIO\n"); +} + +#ifdef CONFIG_CPU_FREQ +static int viper_cpufreq_notifier(struct notifier_block *nb, + unsigned long val, void *data) +{ + struct cpufreq_freqs *freq = data; + + /* TODO: Adjust timings??? */ + + switch (val) { + case CPUFREQ_PRECHANGE: + if (freq->old < freq->new) { + /* we are getting faster so raise the voltage + * before we change freq */ + viper_set_core_cpu_voltage(freq->new, 0); + } + break; + case CPUFREQ_POSTCHANGE: + if (freq->old > freq->new) { + /* we are slowing down so drop the power + * after we change freq */ + viper_set_core_cpu_voltage(freq->new, 0); + } + break; + case CPUFREQ_RESUMECHANGE: + viper_set_core_cpu_voltage(freq->new, 0); + break; + default: + /* ignore */ + break; + } + + return 0; +} + +static struct notifier_block viper_cpufreq_notifier_block = { + .notifier_call = viper_cpufreq_notifier +}; + +static void __init viper_init_cpufreq(void) +{ + if (cpufreq_register_notifier(&viper_cpufreq_notifier_block, + CPUFREQ_TRANSITION_NOTIFIER)) + pr_err("viper: Failed to setup cpufreq notifier\n"); +} +#else +static inline void viper_init_cpufreq(void) {} +#endif + +static void viper_power_off(void) +{ + pr_notice("Shutting off UPS\n"); + gpio_set_value(VIPER_UPS_GPIO, 1); + /* Spin to death... */ + while (1); +} + +static void __init viper_init(void) +{ + u8 version; + + pm_power_off = viper_power_off; + + pxa2xx_mfp_config(ARRAY_AND_SIZE(viper_pin_config)); + + /* Wake-up serial console */ + viper_init_serial_gpio(); + + set_pxa_fb_info(&fb_info); + + /* v1 hardware cannot use the datacs line */ + version = viper_hw_version(); + if (version == 0) + smc91x_device.num_resources--; + + pxa_set_i2c_info(NULL); + platform_add_devices(viper_devs, ARRAY_SIZE(viper_devs)); + + viper_init_vcore_gpios(); + viper_init_cpufreq(); + + sysdev_driver_register(&cpu_sysdev_class, &viper_cpu_sysdev_driver); + + if (version) { + pr_info("viper: hardware v%di%d detected. " + "CPLD revision %d.\n", + VIPER_BOARD_VERSION(version), + VIPER_BOARD_ISSUE(version), + VIPER_CPLD_REVISION(version)); + system_rev = (VIPER_BOARD_VERSION(version) << 8) | + (VIPER_BOARD_ISSUE(version) << 4) | + VIPER_CPLD_REVISION(version); + } else { + pr_info("viper: No version register.\n"); + } + + i2c_register_board_info(1, ARRAY_AND_SIZE(viper_i2c_devices)); + + viper_tpm_init(); + pxa_set_ac97_info(NULL); +} + +static struct map_desc viper_io_desc[] __initdata = { + { + .virtual = VIPER_CPLD_BASE, + .pfn = __phys_to_pfn(VIPER_CPLD_PHYS), + .length = 0x00300000, + .type = MT_DEVICE, + }, + { + .virtual = VIPER_PC104IO_BASE, + .pfn = __phys_to_pfn(_PCMCIA1IO), + .length = 0x00800000, + .type = MT_DEVICE, + }, +}; + +static void __init viper_map_io(void) +{ + pxa_map_io(); + + iotable_init(viper_io_desc, ARRAY_SIZE(viper_io_desc)); + + PCFR |= PCFR_OPDE; +} + +MACHINE_START(VIPER, "Arcom/Eurotech VIPER SBC") + /* Maintainer: Marc Zyngier */ + .phys_io = 0x40000000, + .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc, + .boot_params = 0xa0000100, + .map_io = viper_map_io, + .init_irq = viper_init_irq, + .timer = &pxa_timer, + .init_machine = viper_init, +MACHINE_END -- cgit v1.2.1 From 19ec95df2c4ec2d28919f267c4d17178f8fe9d9c Mon Sep 17 00:00:00 2001 From: Marc Zyngier Date: Tue, 29 Jul 2008 11:33:15 +0200 Subject: Add default configuration for Arcom/Eurotech Viper SBC Signed-off-by: Marc Zyngier --- arch/arm/configs/viper_defconfig | 1678 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 1678 insertions(+) create mode 100644 arch/arm/configs/viper_defconfig (limited to 'arch') diff --git a/arch/arm/configs/viper_defconfig b/arch/arm/configs/viper_defconfig new file mode 100644 index 000000000000..d01fecb8673e --- /dev/null +++ b/arch/arm/configs/viper_defconfig @@ -0,0 +1,1678 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc4 +# Thu Aug 21 17:12:07 2008 +# +CONFIG_ARM=y +CONFIG_HAVE_PWM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_SUPPORTS_AOUT=y +CONFIG_ZONE_DMA=y +CONFIG_ARCH_MTD_XIP=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +# CONFIG_SWAP is not set +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_AUDIT is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=13 +# CONFIG_CGROUPS is not set +# CONFIG_GROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +# CONFIG_ELF_CORE is not set +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +# CONFIG_SHMEM is not set +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_ARCH_TRACEHOOK is not set +# CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +CONFIG_TINY_SHMEM=y +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +# CONFIG_IOSCHED_AS is not set +CONFIG_IOSCHED_DEADLINE=y +# CONFIG_IOSCHED_CFQ is not set +# CONFIG_DEFAULT_AS is not set +CONFIG_DEFAULT_DEADLINE=y +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="deadline" +CONFIG_CLASSIC_RCU=y + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_PNX4008 is not set +CONFIG_ARCH_PXA=y +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +# CONFIG_ARCH_OMAP is not set +# CONFIG_ARCH_MSM7X00A is not set + +# +# Intel PXA2xx/PXA3xx Implementations +# +# CONFIG_ARCH_GUMSTIX is not set +# CONFIG_ARCH_LUBBOCK is not set +# CONFIG_MACH_LOGICPD_PXA270 is not set +# CONFIG_MACH_MAINSTONE is not set +# CONFIG_ARCH_PXA_IDP is not set +# CONFIG_PXA_SHARPSL is not set +CONFIG_ARCH_VIPER=y +# CONFIG_ARCH_PXA_ESERIES is not set +# CONFIG_MACH_TRIZEPS4 is not set +# CONFIG_MACH_EM_X270 is not set +# CONFIG_MACH_COLIBRI is not set +# CONFIG_MACH_ZYLONITE is not set +# CONFIG_MACH_LITTLETON is not set +# CONFIG_MACH_TAVOREVB is not set +# CONFIG_MACH_SAAR is not set +# CONFIG_MACH_ARMCORE is not set +# CONFIG_MACH_MAGICIAN is not set +# CONFIG_MACH_PCM027 is not set +# CONFIG_ARCH_PXA_PALM is not set +# CONFIG_PXA_EZX is not set +CONFIG_PXA25x=y +CONFIG_PXA_PWM=m +CONFIG_PXA_HAVE_ISA_IRQS=y + +# +# Boot options +# + +# +# Power management +# + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_XSCALE=y +CONFIG_CPU_32v5=y +CONFIG_CPU_ABRT_EV5T=y +CONFIG_CPU_PABRT_NOIFAR=y +CONFIG_CPU_CACHE_VIVT=y +CONFIG_CPU_TLB_V4WBI=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_OUTER_CACHE is not set +CONFIG_IWMMXT=y +CONFIG_XSCALE_PMU=y + +# +# Bus support +# +CONFIG_ISA=y +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_PCCARD=m +# CONFIG_PCMCIA_DEBUG is not set +CONFIG_PCMCIA=m +CONFIG_PCMCIA_LOAD_CIS=y +CONFIG_PCMCIA_IOCTL=y + +# +# PC-card bridges +# +# CONFIG_I82365 is not set +# CONFIG_TCIC is not set +CONFIG_PCMCIA_PXA2XX=m +CONFIG_PCMCIA_PROBE=y + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +# CONFIG_NO_HZ is not set +# CONFIG_HIGH_RES_TIMERS is not set +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_PREEMPT is not set +CONFIG_HZ=100 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4096 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="root=31:02 rootfstype=jffs2 ro console=ttyS0,115200" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Frequency scaling +# +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_TABLE=y +# CONFIG_CPU_FREQ_DEBUG is not set +CONFIG_CPU_FREQ_STAT=y +# CONFIG_CPU_FREQ_STAT_DETAILS is not set +CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set +# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +CONFIG_CPU_FREQ_GOV_POWERSAVE=m +CONFIG_CPU_FREQ_GOV_USERSPACE=m +CONFIG_CPU_FREQ_GOV_ONDEMAND=m +CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m +CONFIG_CPU_FREQ_PXA=y + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +# CONFIG_FPE_NWFPE is not set +CONFIG_FPE_FASTFPE=y + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +CONFIG_PM=y +# CONFIG_PM_DEBUG is not set +CONFIG_PM_SLEEP=y +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +# CONFIG_APM_EMULATION is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_XFRM_STATISTICS is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +CONFIG_BT=m +CONFIG_BT_L2CAP=m +# CONFIG_BT_SCO is not set +CONFIG_BT_RFCOMM=m +CONFIG_BT_RFCOMM_TTY=y +CONFIG_BT_BNEP=m +# CONFIG_BT_BNEP_MC_FILTER is not set +# CONFIG_BT_BNEP_PROTO_FILTER is not set +# CONFIG_BT_HIDP is not set + +# +# Bluetooth device drivers +# +CONFIG_BT_HCIUSB=m +# CONFIG_BT_HCIUSB_SCO is not set +# CONFIG_BT_HCIBTUSB is not set +CONFIG_BT_HCIUART=m +CONFIG_BT_HCIUART_H4=y +CONFIG_BT_HCIUART_BCSP=y +# CONFIG_BT_HCIUART_LL is not set +# CONFIG_BT_HCIBCM203X is not set +# CONFIG_BT_HCIBPA10X is not set +# CONFIG_BT_HCIBFUSB is not set +# CONFIG_BT_HCIDTL1 is not set +# CONFIG_BT_HCIBT3C is not set +# CONFIG_BT_HCIBLUECARD is not set +# CONFIG_BT_HCIBTUART is not set +# CONFIG_BT_HCIVHCI is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +CONFIG_IEEE80211=m +# CONFIG_IEEE80211_DEBUG is not set +CONFIG_IEEE80211_CRYPT_WEP=m +# CONFIG_IEEE80211_CRYPT_CCMP is not set +# CONFIG_IEEE80211_CRYPT_TKIP is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +CONFIG_FW_LOADER=m +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_EXTRA_FIRMWARE="" +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +CONFIG_MTD_REDBOOT_PARTS=y +CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=0 +# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set +# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set +# CONFIG_MTD_CMDLINE_PARTS is not set +# CONFIG_MTD_AFS_PARTS is not set +# CONFIG_MTD_AR7_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=m +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set +# CONFIG_MTD_OOPS is not set + +# +# RAM/ROM/Flash chip drivers +# +CONFIG_MTD_CFI=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_NOSWAP=y +# CONFIG_MTD_CFI_BE_BYTE_SWAP is not set +# CONFIG_MTD_CFI_LE_BYTE_SWAP is not set +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +# CONFIG_MTD_CFI_I2 is not set +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_OTP is not set +CONFIG_MTD_CFI_INTELEXT=y +CONFIG_MTD_CFI_AMDSTD=y +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +CONFIG_MTD_RAM=y +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_ABSENT is not set +# CONFIG_MTD_XIP is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_PHYSMAP_START=0x8000000 +CONFIG_MTD_PHYSMAP_LEN=0 +CONFIG_MTD_PHYSMAP_BANKWIDTH=2 +CONFIG_MTD_PXA2XX=y +# CONFIG_MTD_ARM_INTEGRATOR is not set +# CONFIG_MTD_IMPA7 is not set +# CONFIG_MTD_SHARP_SL is not set +# CONFIG_MTD_PLATRAM is not set +CONFIG_MTD_SPARSE_RAM=y + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +# CONFIG_MTD_NAND is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set +# CONFIG_PARPORT is not set +# CONFIG_PNP is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=m +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +# CONFIG_BLK_DEV_NBD is not set +# CONFIG_BLK_DEV_UB is not set +# CONFIG_BLK_DEV_RAM is not set +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set +CONFIG_MISC_DEVICES=y +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=m +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_SCSI_PROC_FS is not set + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=m +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_ISCSI_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_ISCSI_TCP is not set +# CONFIG_SCSI_AHA152X is not set +# CONFIG_SCSI_AIC7XXX_OLD is not set +# CONFIG_SCSI_ADVANSYS is not set +# CONFIG_SCSI_IN2000 is not set +# CONFIG_SCSI_DTC3280 is not set +# CONFIG_SCSI_FUTURE_DOMAIN is not set +# CONFIG_SCSI_GENERIC_NCR5380 is not set +# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set +# CONFIG_SCSI_NCR53C406A is not set +# CONFIG_SCSI_PAS16 is not set +# CONFIG_SCSI_QLOGIC_FAS is not set +# CONFIG_SCSI_SYM53C416 is not set +# CONFIG_SCSI_T128 is not set +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set +# CONFIG_SCSI_DH is not set +CONFIG_ATA=m +# CONFIG_ATA_NONSTANDARD is not set +# CONFIG_SATA_PMP is not set +CONFIG_ATA_SFF=y +# CONFIG_SATA_MV is not set +# CONFIG_PATA_LEGACY is not set +CONFIG_PATA_PCMCIA=m +# CONFIG_PATA_QDI is not set +# CONFIG_PATA_WINBOND_VLB is not set +# CONFIG_PATA_PLATFORM is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +# CONFIG_ARCNET is not set +# CONFIG_PHYLIB is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_NET_VENDOR_3COM is not set +# CONFIG_NET_VENDOR_SMC is not set +CONFIG_SMC91X=y +# CONFIG_DM9000 is not set +# CONFIG_SMC911X is not set +# CONFIG_NET_VENDOR_RACAL is not set +# CONFIG_AT1700 is not set +# CONFIG_DEPCA is not set +# CONFIG_HP100 is not set +# CONFIG_NET_ISA is not set +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_NET_PCI is not set +# CONFIG_B44 is not set +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETDEV_10000 is not set +# CONFIG_TR is not set + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +CONFIG_USB_PEGASUS=m +# CONFIG_USB_RTL8150 is not set +CONFIG_USB_USBNET=m +CONFIG_USB_NET_AX8817X=m +CONFIG_USB_NET_CDCETHER=m +# CONFIG_USB_NET_DM9601 is not set +# CONFIG_USB_NET_GL620A is not set +CONFIG_USB_NET_NET1080=m +# CONFIG_USB_NET_PLUSB is not set +# CONFIG_USB_NET_MCS7830 is not set +# CONFIG_USB_NET_RNDIS_HOST is not set +# CONFIG_USB_NET_CDC_SUBSET is not set +CONFIG_USB_NET_ZAURUS=m +CONFIG_NET_PCMCIA=y +# CONFIG_PCMCIA_3C589 is not set +# CONFIG_PCMCIA_3C574 is not set +# CONFIG_PCMCIA_FMVJ18X is not set +# CONFIG_PCMCIA_PCNET is not set +# CONFIG_PCMCIA_NMCLAN is not set +# CONFIG_PCMCIA_SMC91C92 is not set +# CONFIG_PCMCIA_XIRC2PS is not set +# CONFIG_PCMCIA_AXNET is not set +# CONFIG_WAN is not set +CONFIG_PPP=m +# CONFIG_PPP_MULTILINK is not set +# CONFIG_PPP_FILTER is not set +CONFIG_PPP_ASYNC=m +# CONFIG_PPP_SYNC_TTY is not set +CONFIG_PPP_DEFLATE=m +CONFIG_PPP_BSDCOMP=m +# CONFIG_PPP_MPPE is not set +# CONFIG_PPPOE is not set +# CONFIG_PPPOL2TP is not set +# CONFIG_SLIP is not set +CONFIG_SLHC=m +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +CONFIG_INPUT_MOUSEDEV=m +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=m +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_FUJITSU=m +# CONFIG_TOUCHSCREEN_GUNZE is not set +CONFIG_TOUCHSCREEN_ELO=m +CONFIG_TOUCHSCREEN_MTOUCH=m +CONFIG_TOUCHSCREEN_INEXIO=m +# CONFIG_TOUCHSCREEN_MK712 is not set +CONFIG_TOUCHSCREEN_HTCPEN=m +CONFIG_TOUCHSCREEN_PENMOUNT=m +CONFIG_TOUCHSCREEN_TOUCHRIGHT=m +CONFIG_TOUCHSCREEN_TOUCHWIN=m +# CONFIG_TOUCHSCREEN_UCB1400 is not set +# CONFIG_TOUCHSCREEN_WM97XX is not set +# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set +CONFIG_TOUCHSCREEN_TOUCHIT213=m +CONFIG_INPUT_MISC=y +# CONFIG_INPUT_ATI_REMOTE is not set +# CONFIG_INPUT_ATI_REMOTE2 is not set +# CONFIG_INPUT_KEYSPAN_REMOTE is not set +# CONFIG_INPUT_POWERMATE is not set +# CONFIG_INPUT_YEALINK is not set +CONFIG_INPUT_UINPUT=m + +# +# Hardware I/O ports +# +CONFIG_SERIO=y +CONFIG_SERIO_SERPORT=y +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_RAW is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +# CONFIG_CONSOLE_TRANSLATIONS is not set +# CONFIG_VT_CONSOLE is not set +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=m +# CONFIG_SERIAL_8250_CS is not set +CONFIG_SERIAL_8250_NR_UARTS=5 +CONFIG_SERIAL_8250_RUNTIME_UARTS=5 +# CONFIG_SERIAL_8250_EXTENDED is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_PXA=y +CONFIG_SERIAL_PXA_CONSOLE=y +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=m +# CONFIG_NVRAM is not set +# CONFIG_DTLK is not set +# CONFIG_R3964 is not set + +# +# PCMCIA character devices +# +# CONFIG_SYNCLINK_CS is not set +# CONFIG_CARDMAN_4000 is not set +# CONFIG_CARDMAN_4040 is not set +# CONFIG_IPWIRELESS is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_DEVPORT=y +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +# CONFIG_I2C_HELPER_AUTO is not set + +# +# I2C Algorithms +# +CONFIG_I2C_ALGOBIT=y +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +CONFIG_I2C_GPIO=y +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_PXA=y +# CONFIG_I2C_PXA_SLAVE is not set +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set +# CONFIG_I2C_TINY_USB is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_ELEKTOR is not set +# CONFIG_I2C_PCA_ISA is not set +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_AT24 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_TPS65010 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +# CONFIG_SPI is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +CONFIG_GPIO_SYSFS=y + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_W1 is not set +# CONFIG_POWER_SUPPLY is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_AD7414 is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ADT7470 is not set +# CONFIG_SENSORS_ADT7473 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_F71882FG is not set +# CONFIG_SENSORS_F75375S is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_LM93 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_DME1737 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_ADS7828 is not set +# CONFIG_SENSORS_THMC50 is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83L786NG is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +# CONFIG_SA1100_WATCHDOG is not set + +# +# ISA-based Watchdog Cards +# +# CONFIG_PCWATCHDOG is not set +# CONFIG_MIXCOMWD is not set +# CONFIG_WDT is not set + +# +# USB-based Watchdog Cards +# +# CONFIG_USBPCWATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +# CONFIG_VIDEO_OUTPUT_CONTROL is not set +CONFIG_FB=y +# CONFIG_FIRMWARE_EDID is not set +# CONFIG_FB_DDC is not set +CONFIG_FB_CFB_FILLRECT=m +CONFIG_FB_CFB_COPYAREA=m +CONFIG_FB_CFB_IMAGEBLIT=m +# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set +# CONFIG_FB_SYS_FILLRECT is not set +# CONFIG_FB_SYS_COPYAREA is not set +# CONFIG_FB_SYS_IMAGEBLIT is not set +# CONFIG_FB_FOREIGN_ENDIAN is not set +# CONFIG_FB_SYS_FOPS is not set +# CONFIG_FB_SVGALIB is not set +# CONFIG_FB_MACMODES is not set +# CONFIG_FB_BACKLIGHT is not set +# CONFIG_FB_MODE_HELPERS is not set +# CONFIG_FB_TILEBLITTING is not set + +# +# Frame buffer hardware drivers +# +# CONFIG_FB_S1D13XXX is not set +CONFIG_FB_PXA=m +# CONFIG_FB_PXA_SMARTPANEL is not set +CONFIG_FB_PXA_PARAMETERS=y +# CONFIG_FB_MBX is not set +# CONFIG_FB_W100 is not set +# CONFIG_FB_AM200EPD is not set +# CONFIG_FB_VIRTUAL is not set +CONFIG_BACKLIGHT_LCD_SUPPORT=y +CONFIG_LCD_CLASS_DEVICE=m +# CONFIG_LCD_ILI9320 is not set +# CONFIG_LCD_PLATFORM is not set +CONFIG_BACKLIGHT_CLASS_DEVICE=m +# CONFIG_BACKLIGHT_CORGI is not set +CONFIG_BACKLIGHT_PWM=m + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +# CONFIG_MDA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_FRAMEBUFFER_CONSOLE=m +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set +# CONFIG_FONTS is not set +CONFIG_FONT_8x8=y +CONFIG_FONT_8x16=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_MONO=y +CONFIG_LOGO_LINUX_VGA16=y +CONFIG_LOGO_LINUX_CLUT224=y +CONFIG_SOUND=m +CONFIG_SND=m +CONFIG_SND_TIMER=m +CONFIG_SND_PCM=m +# CONFIG_SND_SEQUENCER is not set +CONFIG_SND_OSSEMUL=y +CONFIG_SND_MIXER_OSS=m +CONFIG_SND_PCM_OSS=m +CONFIG_SND_PCM_OSS_PLUGINS=y +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_VMASTER=y +CONFIG_SND_AC97_CODEC=m +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +# CONFIG_SND_AC97_POWER_SAVE is not set +CONFIG_SND_ARM=y +CONFIG_SND_PXA2XX_PCM=m +CONFIG_SND_PXA2XX_AC97=m +CONFIG_SND_USB=y +# CONFIG_SND_USB_AUDIO is not set +# CONFIG_SND_USB_CAIAQ is not set +CONFIG_SND_PCMCIA=y +# CONFIG_SND_VXPOCKET is not set +# CONFIG_SND_PDAUDIOCF is not set +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_AC97_BUS=m +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set + +# +# USB Input Devices +# +CONFIG_USB_HID=m +# CONFIG_USB_HIDINPUT_POWERBOOK is not set +# CONFIG_HID_FF is not set +# CONFIG_USB_HIDDEV is not set + +# +# USB HID Boot Protocol drivers +# +# CONFIG_USB_KBD is not set +# CONFIG_USB_MOUSE is not set +CONFIG_USB_SUPPORT=y +CONFIG_USB_ARCH_HAS_HCD=y +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set +CONFIG_USB=m +# CONFIG_USB_DEBUG is not set +# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set + +# +# Miscellaneous USB options +# +CONFIG_USB_DEVICEFS=y +CONFIG_USB_DEVICE_CLASS=y +# CONFIG_USB_DYNAMIC_MINORS is not set +CONFIG_USB_SUSPEND=y +# CONFIG_USB_OTG is not set +# CONFIG_USB_OTG_WHITELIST is not set +# CONFIG_USB_OTG_BLACKLIST_HUB is not set +# CONFIG_USB_MON is not set + +# +# USB Host Controller Drivers +# +# CONFIG_USB_C67X00_HCD is not set +CONFIG_USB_ISP116X_HCD=m +# CONFIG_USB_ISP1760_HCD is not set +CONFIG_USB_SL811_HCD=m +# CONFIG_USB_SL811_CS is not set +CONFIG_USB_R8A66597_HCD=m +# CONFIG_USB_MUSB_HDRC is not set +# CONFIG_USB_GADGET_MUSB_HDRC is not set + +# +# USB Device Class drivers +# +CONFIG_USB_ACM=m +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_WDM is not set + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# may also be needed; see USB_STORAGE Help for more information +# +CONFIG_USB_STORAGE=m +# CONFIG_USB_STORAGE_DEBUG is not set +# CONFIG_USB_STORAGE_DATAFAB is not set +# CONFIG_USB_STORAGE_FREECOM is not set +# CONFIG_USB_STORAGE_ISD200 is not set +# CONFIG_USB_STORAGE_DPCM is not set +# CONFIG_USB_STORAGE_USBAT is not set +# CONFIG_USB_STORAGE_SDDR09 is not set +# CONFIG_USB_STORAGE_SDDR55 is not set +# CONFIG_USB_STORAGE_JUMPSHOT is not set +# CONFIG_USB_STORAGE_ALAUDA is not set +# CONFIG_USB_STORAGE_ONETOUCH is not set +# CONFIG_USB_STORAGE_KARMA is not set +# CONFIG_USB_STORAGE_SIERRA is not set +# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set +# CONFIG_USB_LIBUSUAL is not set + +# +# USB Imaging devices +# +# CONFIG_USB_MDC800 is not set +# CONFIG_USB_MICROTEK is not set + +# +# USB port drivers +# +CONFIG_USB_SERIAL=m +# CONFIG_USB_EZUSB is not set +CONFIG_USB_SERIAL_GENERIC=y +# CONFIG_USB_SERIAL_AIRCABLE is not set +# CONFIG_USB_SERIAL_ARK3116 is not set +# CONFIG_USB_SERIAL_BELKIN is not set +# CONFIG_USB_SERIAL_CH341 is not set +# CONFIG_USB_SERIAL_WHITEHEAT is not set +# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set +# CONFIG_USB_SERIAL_CP2101 is not set +# CONFIG_USB_SERIAL_CYPRESS_M8 is not set +# CONFIG_USB_SERIAL_EMPEG is not set +# CONFIG_USB_SERIAL_FTDI_SIO is not set +# CONFIG_USB_SERIAL_FUNSOFT is not set +# CONFIG_USB_SERIAL_VISOR is not set +# CONFIG_USB_SERIAL_IPAQ is not set +# CONFIG_USB_SERIAL_IR is not set +# CONFIG_USB_SERIAL_EDGEPORT is not set +# CONFIG_USB_SERIAL_EDGEPORT_TI is not set +# CONFIG_USB_SERIAL_GARMIN is not set +# CONFIG_USB_SERIAL_IPW is not set +# CONFIG_USB_SERIAL_IUU is not set +# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set +# CONFIG_USB_SERIAL_KEYSPAN is not set +# CONFIG_USB_SERIAL_KLSI is not set +# CONFIG_USB_SERIAL_KOBIL_SCT is not set +CONFIG_USB_SERIAL_MCT_U232=m +# CONFIG_USB_SERIAL_MOS7720 is not set +# CONFIG_USB_SERIAL_MOS7840 is not set +# CONFIG_USB_SERIAL_MOTOROLA is not set +# CONFIG_USB_SERIAL_NAVMAN is not set +# CONFIG_USB_SERIAL_PL2303 is not set +# CONFIG_USB_SERIAL_OTI6858 is not set +# CONFIG_USB_SERIAL_SPCP8X5 is not set +# CONFIG_USB_SERIAL_HP4X is not set +# CONFIG_USB_SERIAL_SAFE is not set +# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set +# CONFIG_USB_SERIAL_TI is not set +# CONFIG_USB_SERIAL_CYBERJACK is not set +# CONFIG_USB_SERIAL_XIRCOM is not set +# CONFIG_USB_SERIAL_OPTION is not set +# CONFIG_USB_SERIAL_OMNINET is not set +# CONFIG_USB_SERIAL_DEBUG is not set + +# +# USB Miscellaneous drivers +# +# CONFIG_USB_EMI62 is not set +# CONFIG_USB_EMI26 is not set +# CONFIG_USB_ADUTUX is not set +# CONFIG_USB_RIO500 is not set +# CONFIG_USB_LEGOTOWER is not set +# CONFIG_USB_LCD is not set +# CONFIG_USB_BERRY_CHARGE is not set +# CONFIG_USB_LED is not set +# CONFIG_USB_CYPRESS_CY7C63 is not set +# CONFIG_USB_CYTHERM is not set +# CONFIG_USB_PHIDGET is not set +# CONFIG_USB_IDMOUSE is not set +# CONFIG_USB_FTDI_ELAN is not set +# CONFIG_USB_APPLEDISPLAY is not set +# CONFIG_USB_LD is not set +# CONFIG_USB_TRANCEVIBRATOR is not set +# CONFIG_USB_IOWARRIOR is not set +# CONFIG_USB_TEST is not set +# CONFIG_USB_ISIGHTFW is not set +CONFIG_USB_GADGET=m +# CONFIG_USB_GADGET_DEBUG is not set +# CONFIG_USB_GADGET_DEBUG_FILES is not set +CONFIG_USB_GADGET_SELECTED=y +# CONFIG_USB_GADGET_AMD5536UDC is not set +# CONFIG_USB_GADGET_ATMEL_USBA is not set +# CONFIG_USB_GADGET_FSL_USB2 is not set +# CONFIG_USB_GADGET_NET2280 is not set +CONFIG_USB_GADGET_PXA25X=y +CONFIG_USB_PXA25X=m +# CONFIG_USB_PXA25X_SMALL is not set +# CONFIG_USB_GADGET_M66592 is not set +# CONFIG_USB_GADGET_PXA27X is not set +# CONFIG_USB_GADGET_GOKU is not set +# CONFIG_USB_GADGET_LH7A40X is not set +# CONFIG_USB_GADGET_OMAP is not set +# CONFIG_USB_GADGET_S3C2410 is not set +# CONFIG_USB_GADGET_AT91 is not set +# CONFIG_USB_GADGET_DUMMY_HCD is not set +# CONFIG_USB_GADGET_DUALSPEED is not set +# CONFIG_USB_ZERO is not set +CONFIG_USB_ETH=m +CONFIG_USB_ETH_RNDIS=y +CONFIG_USB_GADGETFS=m +CONFIG_USB_FILE_STORAGE=m +# CONFIG_USB_FILE_STORAGE_TEST is not set +CONFIG_USB_G_SERIAL=m +# CONFIG_USB_MIDI_GADGET is not set +CONFIG_USB_G_PRINTER=m +# CONFIG_USB_CDC_COMPOSITE is not set +# CONFIG_MMC is not set +# CONFIG_NEW_LEDS is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=m + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +CONFIG_RTC_DRV_DS1307=m +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_SA1100=m +# CONFIG_DMADEVICES is not set + +# +# Voltage and Current regulators +# +# CONFIG_REGULATOR is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=m +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=m +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=m +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_DNOTIFY is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=m +# CONFIG_MSDOS_FS is not set +CONFIG_VFAT_FS=m +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_JFFS2_FS=y +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_FS_WBUF_VERIFY is not set +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +# CONFIG_JFFS2_LZO is not set +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +CONFIG_ROOT_NFS=y +CONFIG_NFSD=m +CONFIG_NFSD_V3=y +# CONFIG_NFSD_V3_ACL is not set +# CONFIG_NFSD_V4 is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_EXPORTFS=m +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=m +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=m +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +CONFIG_NLS_CODEPAGE_850=m +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=m +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +CONFIG_NLS_ISO8859_15=m +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +CONFIG_NLS_UTF8=m +# CONFIG_DLM is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +CONFIG_DEBUG_BUGVERBOSE=y +# CONFIG_DEBUG_INFO is not set +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_SYSCTL_SYSCALL_CHECK=y +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_USER is not set +CONFIG_DEBUG_ERRORS=y +# CONFIG_DEBUG_STACK_USAGE is not set +# CONFIG_DEBUG_LL is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=m +CONFIG_CRYPTO_BLKCIPHER=m +CONFIG_CRYPTO_MANAGER=m +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +# CONFIG_CRYPTO_CBC is not set +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +# CONFIG_CRYPTO_PCBC is not set +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +# CONFIG_CRYPTO_MD5 is not set +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +CONFIG_CRYPTO_ARC4=m +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +# CONFIG_CRYPTO_DES is not set +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set +CONFIG_CRC_CCITT=m +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=m +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y -- cgit v1.2.1