From 2d244c81481fa5142a2ba6656ab7a8e40c849c27 Mon Sep 17 00:00:00 2001 From: Xiangliang Yu Date: Fri, 11 Dec 2015 20:02:53 +0800 Subject: i2c: designware: fix IO timeout issue for AMD controller Because of some hardware limitation, AMD I2C controller can't trigger pending interrupt if interrupt status has been changed after clearing interrupt status bits. Then, I2C will lost interrupt and IO timeout. According to hardware design, this patch implements a workaround to disable i2c controller interrupt and re-enable i2c interrupt before exiting ISR. To reduce the performance impacts on other vendors, use unlikely function to check flag in ISR. Signed-off-by: Xiangliang Yu Acked-by: Jarkko Nikula Signed-off-by: Wolfram Sang Cc: stable@kernel.org --- drivers/i2c/busses/i2c-designware-platdrv.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/i2c/busses/i2c-designware-platdrv.c') diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index 809579ecb5a4..f03ea71d6519 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -93,6 +93,7 @@ static void dw_i2c_acpi_params(struct platform_device *pdev, char method[], static int dw_i2c_acpi_configure(struct platform_device *pdev) { struct dw_i2c_dev *dev = platform_get_drvdata(pdev); + const struct acpi_device_id *id; dev->adapter.nr = -1; dev->tx_fifo_depth = 32; @@ -106,6 +107,10 @@ static int dw_i2c_acpi_configure(struct platform_device *pdev) dw_i2c_acpi_params(pdev, "FMCN", &dev->fs_hcnt, &dev->fs_lcnt, &dev->sda_hold_time); + id = acpi_match_device(pdev->dev.driver->acpi_match_table, &pdev->dev); + if (id && id->driver_data) + dev->accessor_flags |= (u32)id->driver_data; + return 0; } @@ -116,7 +121,7 @@ static const struct acpi_device_id dw_i2c_acpi_match[] = { { "INT3433", 0 }, { "80860F41", 0 }, { "808622C1", 0 }, - { "AMD0010", 0 }, + { "AMD0010", ACCESS_INTR_MASK }, { } }; MODULE_DEVICE_TABLE(acpi, dw_i2c_acpi_match); -- cgit v1.2.1 From e79e72c5a242fa21c971cfb40017f1039daf4d77 Mon Sep 17 00:00:00 2001 From: Jarkko Nikula Date: Thu, 10 Dec 2015 13:48:43 +0200 Subject: i2c: designware: Keep pm_runtime_enable/_disable calls in sync On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the runtime PM disable depth keeps increasing over repeated modprobe/rmmod cycle because pm_runtime_disable() is called without checking should it be disabled already because of bus sharing. This hasn't made any other harm than dev->power.disable_depth keeps increasing but keep it sync by calling pm_runtime_disable() only when runtime PM is not disabled. Reported-by: Wolfram Sang Signed-off-by: Jarkko Nikula Signed-off-by: Wolfram Sang --- drivers/i2c/busses/i2c-designware-platdrv.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) (limited to 'drivers/i2c/busses/i2c-designware-platdrv.c') diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index f03ea71d6519..6b00061c3746 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -245,12 +245,10 @@ static int dw_i2c_plat_probe(struct platform_device *pdev) } r = i2c_dw_probe(dev); - if (r) { + if (r && !dev->pm_runtime_disabled) pm_runtime_disable(&pdev->dev); - return r; - } - return 0; + return r; } static int dw_i2c_plat_remove(struct platform_device *pdev) @@ -265,7 +263,8 @@ static int dw_i2c_plat_remove(struct platform_device *pdev) pm_runtime_dont_use_autosuspend(&pdev->dev); pm_runtime_put_sync(&pdev->dev); - pm_runtime_disable(&pdev->dev); + if (!dev->pm_runtime_disabled) + pm_runtime_disable(&pdev->dev); return 0; } -- cgit v1.2.1