diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2020-06-03 16:27:18 -0700 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2020-06-03 16:27:18 -0700 |
| commit | cb8e59cc87201af93dfbb6c3dccc8fcad72a09c2 (patch) | |
| tree | a334db9022f89654b777bbce8c4c6632e65b9031 /Documentation/devicetree/bindings/net | |
| parent | 2e63f6ce7ed2c4ff83ba30ad9ccad422289a6c63 (diff) | |
| parent | 065fcfd49763ec71ae345bb5c5a74f961031e70e (diff) | |
| download | linux-rt-cb8e59cc87201af93dfbb6c3dccc8fcad72a09c2.tar.gz | |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Diffstat (limited to 'Documentation/devicetree/bindings/net')
22 files changed, 1046 insertions, 190 deletions
diff --git a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml index ae91aa9d8616..64c20c92c07d 100644 --- a/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml +++ b/Documentation/devicetree/bindings/net/amlogic,meson-dwmac.yaml @@ -40,18 +40,22 @@ allOf: then: properties: clocks: + minItems: 3 + maxItems: 4 items: - description: GMAC main clock - description: First parent clock of the internal mux - description: Second parent clock of the internal mux + - description: The clock which drives the timing adjustment logic clock-names: minItems: 3 - maxItems: 3 + maxItems: 4 items: - const: stmmaceth - const: clkin0 - const: clkin1 + - const: timing-adjustment amlogic,tx-delay-ns: $ref: /schemas/types.yaml#definitions/uint32 @@ -67,6 +71,19 @@ allOf: PHY and MAC are adding a delay). Any configuration is ignored when the phy-mode is set to "rmii". + amlogic,rx-delay-ns: + enum: + - 0 + - 2 + default: 0 + description: + The internal RGMII RX clock delay (provided by this IP block) in + nanoseconds. When phy-mode is set to "rgmii" then the RX delay + should be explicitly configured. When the phy-mode is set to + either "rgmii-id" or "rgmii-rxid" the RX clock delay is already + provided by the PHY. Any configuration is ignored when the + phy-mode is set to "rmii". + properties: compatible: additionalItems: true @@ -107,7 +124,7 @@ examples: reg = <0xc9410000 0x10000>, <0xc8834540 0x8>; interrupts = <8>; interrupt-names = "macirq"; - clocks = <&clk_eth>, <&clkc_fclk_div2>, <&clk_mpll2>; - clock-names = "stmmaceth", "clkin0", "clkin1"; + clocks = <&clk_eth>, <&clk_fclk_div2>, <&clk_mpll2>, <&clk_fclk_div2>; + clock-names = "stmmaceth", "clkin0", "clkin1", "timing-adjustment"; phy-mode = "rgmii"; }; diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml index 5aa141ccc113..9b1f1147ca36 100644 --- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml @@ -81,7 +81,8 @@ properties: $ref: /schemas/types.yaml#definitions/flag description: If set, indicates the PHY device does not correctly release - the turn around line low at the end of a MDIO transaction. + the turn around line low at end of the control phase of the + MDIO transaction. enet-phy-lane-swap: $ref: /schemas/types.yaml#definitions/flag diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index ff8b0f211aa1..9b543789cd52 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -22,8 +22,11 @@ Optional properties: - fsl,err006687-workaround-present: If present indicates that the system has the hardware workaround for ERR006687 applied and does not need a software workaround. -- gpr: phandle of SoC general purpose register mode. Required for wake on LAN - on some SoCs +- fsl,stop-mode: register bits of stop mode control, the format is + <&gpr req_gpr req_bit>. + gpr is the phandle to general purpose register node. + req_gpr is the gpr register offset for ENET stop request. + req_bit is the gpr bit offset for ENET stop request. -interrupt-names: names of the interrupts listed in interrupts property in the same order. The defaults if not specified are __Number of interrupts__ __Default__ @@ -82,6 +85,7 @@ ethernet@83fec000 { phy-supply = <®_fec_supply>; phy-handle = <ðphy>; mdio { + clock-frequency = <5000000>; ethphy: ethernet-phy@6 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <6>; diff --git a/Documentation/devicetree/bindings/net/imx-dwmac.txt b/Documentation/devicetree/bindings/net/imx-dwmac.txt new file mode 100644 index 000000000000..921d522fe8d7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/imx-dwmac.txt @@ -0,0 +1,56 @@ +IMX8 glue layer controller, NXP imx8 families support Synopsys MAC 5.10a IP. + +This file documents platform glue layer for IMX. +Please see stmmac.txt for the other unchanged properties. + +The device node has following properties. + +Required properties: +- compatible: Should be "nxp,imx8mp-dwmac-eqos" to select glue layer + and "snps,dwmac-5.10a" to select IP version. +- clocks: Must contain a phandle for each entry in clock-names. +- clock-names: Should be "stmmaceth" for the host clock. + Should be "pclk" for the MAC apb clock. + Should be "ptp_ref" for the MAC timer clock. + Should be "tx" for the MAC RGMII TX clock: + Should be "mem" for EQOS MEM clock. + - "mem" clock is required for imx8dxl platform. + - "mem" clock is not required for imx8mp platform. +- interrupt-names: Should contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Should be "macirq" for the main MAC IRQ + Should be "eth_wake_irq" for the IT which wake up system +- intf_mode: Should be phandle/offset pair. The phandle to the syscon node which + encompases the GPR register, and the offset of the GPR register. + - required for imx8mp platform. + - is optional for imx8dxl platform. + +Optional properties: +- intf_mode: is optional for imx8dxl platform. +- snps,rmii_refclk_ext: to select RMII reference clock from external. + +Example: + eqos: ethernet@30bf0000 { + compatible = "nxp,imx8mp-dwmac-eqos", "snps,dwmac-5.10a"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "eth_wake_irq", "macirq"; + clocks = <&clk IMX8MP_CLK_ENET_QOS_ROOT>, + <&clk IMX8MP_CLK_QOS_ENET_ROOT>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + clock-names = "stmmaceth", "pclk", "ptp_ref", "tx"; + assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, + <&clk IMX8MP_CLK_ENET_QOS_TIMER>, + <&clk IMX8MP_CLK_ENET_QOS>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, + <&clk IMX8MP_SYS_PLL2_100M>, + <&clk IMX8MP_SYS_PLL2_125M>; + assigned-clock-rates = <0>, <100000000>, <125000000>; + nvmem-cells = <ð_mac0>; + nvmem-cell-names = "mac-address"; + nvmem_macaddr_swap; + intf_mode = <&gpr 0x4>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/net/mdio.yaml b/Documentation/devicetree/bindings/net/mdio.yaml index 50c3397a82bc..d6a3bf8550eb 100644 --- a/Documentation/devicetree/bindings/net/mdio.yaml +++ b/Documentation/devicetree/bindings/net/mdio.yaml @@ -31,13 +31,25 @@ properties: maxItems: 1 description: The phandle and specifier for the GPIO that controls the RESET - lines of all PHYs on that MDIO bus. + lines of all devices on that MDIO bus. reset-delay-us: description: - RESET pulse width in microseconds. It applies to all PHY devices - and must therefore be appropriately determined based on all PHY - requirements (maximum value of all per-PHY RESET pulse widths). + RESET pulse width in microseconds. It applies to all MDIO devices + and must therefore be appropriately determined based on all devices + requirements (maximum value of all per-device RESET pulse widths). + + clock-frequency: + description: + Desired MDIO bus clock frequency in Hz. Values greater than IEEE 802.3 + defined 2.5MHz should only be used when all devices on the bus support + the given clock speed. + + suppress-preamble: + description: + The 32 bit preamble should be suppressed. In order for this to + work, all devices on the bus must support suppressed preamble. + type: boolean patternProperties: "^ethernet-phy@[0-9a-f]+$": @@ -48,7 +60,35 @@ patternProperties: minimum: 0 maximum: 31 description: - The ID number for the PHY. + The ID number for the device. + + broken-turn-around: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates the MDIO device does not correctly release + the turn around line low at end of the control phase of the + MDIO transaction. + + resets: + maxItems: 1 + + reset-names: + const: phy + + reset-gpios: + maxItems: 1 + description: + The GPIO phandle and specifier for the MDIO reset signal. + + reset-assert-us: + description: + Delay after the reset was asserted in microseconds. If this + property is missing the delay will be skipped. + + reset-deassert-us: + description: + Delay after the reset was deasserted in microseconds. If + this property is missing the delay will be skipped. required: - reg diff --git a/Documentation/devicetree/bindings/net/mediatek,star-emac.yaml b/Documentation/devicetree/bindings/net/mediatek,star-emac.yaml new file mode 100644 index 000000000000..aea88e621792 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek,star-emac.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/mediatek,star-emac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek STAR Ethernet MAC Controller + +maintainers: + - Bartosz Golaszewski <bgolaszewski@baylibre.com> + +description: + This Ethernet MAC is used on the MT8* family of SoCs from MediaTek. + It's compliant with 802.3 standards and supports half- and full-duplex + modes with flow-control as well as CRC offloading and VLAN tags. + +allOf: + - $ref: "ethernet-controller.yaml#" + +properties: + compatible: + enum: + - mediatek,mt8516-eth + - mediatek,mt8518-eth + - mediatek,mt8175-eth + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + minItems: 3 + maxItems: 3 + + clock-names: + additionalItems: false + items: + - const: core + - const: reg + - const: trans + + mediatek,pericfg: + $ref: /schemas/types.yaml#definitions/phandle + description: + Phandle to the device containing the PERICFG register range. This is used + to control the MII mode. + + mdio: + type: object + description: + Creates and registers an MDIO bus. + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - mediatek,pericfg + - phy-handle + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/mt8516-clk.h> + + ethernet: ethernet@11180000 { + compatible = "mediatek,mt8516-eth"; + reg = <0x11180000 0x1000>; + mediatek,pericfg = <&pericfg>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_RG_ETH>, + <&topckgen CLK_TOP_66M_ETH>, + <&topckgen CLK_TOP_133M_ETH>; + clock-names = "core", "reg", "trans"; + phy-handle = <ð_phy>; + phy-mode = "rmii"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + eth_phy: ethernet-phy@0 { + reg = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml b/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml new file mode 100644 index 000000000000..42be0255512b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nxp,tja11xx.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0+ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/nxp,tja11xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP TJA11xx PHY + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Heiner Kallweit <hkallweit1@gmail.com> + +description: + Bindings for NXP TJA11xx automotive PHYs + +allOf: + - $ref: ethernet-phy.yaml# + +patternProperties: + "^ethernet-phy@[0-9a-f]+$": + type: object + description: | + Some packages have multiple PHYs. Secondary PHY should be defines as + subnode of the first (parent) PHY. + + properties: + reg: + minimum: 0 + maximum: 31 + description: + The ID number for the child PHY. Should be +1 of parent PHY. + + required: + - reg + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + tja1101_phy0: ethernet-phy@4 { + reg = <0x4>; + }; + }; + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + tja1102_phy0: ethernet-phy@4 { + reg = <0x4>; + #address-cells = <1>; + #size-cells = <0>; + + tja1102_phy1: ethernet-phy@5 { + reg = <0x5>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qca,ar71xx.txt b/Documentation/devicetree/bindings/net/qca,ar71xx.txt deleted file mode 100644 index 2a33e71ba72b..000000000000 --- a/Documentation/devicetree/bindings/net/qca,ar71xx.txt +++ /dev/null @@ -1,45 +0,0 @@ -Required properties: -- compatible: Should be "qca,<soc>-eth". Currently support compatibles are: - qca,ar7100-eth - Atheros AR7100 - qca,ar7240-eth - Atheros AR7240 - qca,ar7241-eth - Atheros AR7241 - qca,ar7242-eth - Atheros AR7242 - qca,ar9130-eth - Atheros AR9130 - qca,ar9330-eth - Atheros AR9330 - qca,ar9340-eth - Atheros AR9340 - qca,qca9530-eth - Qualcomm Atheros QCA9530 - qca,qca9550-eth - Qualcomm Atheros QCA9550 - qca,qca9560-eth - Qualcomm Atheros QCA9560 - -- reg : Address and length of the register set for the device -- interrupts : Should contain eth interrupt -- phy-mode : See ethernet.txt file in the same directory -- clocks: the clock used by the core -- clock-names: the names of the clock listed in the clocks property. These are - "eth" and "mdio". -- resets: Should contain phandles to the reset signals -- reset-names: Should contain the names of reset signal listed in the resets - property. These are "mac" and "mdio" - -Optional properties: -- phy-handle : phandle to the PHY device connected to this device. -- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. - Use instead of phy-handle. - -Optional subnodes: -- mdio : specifies the mdio bus, used as a container for phy nodes - according to phy.txt in the same directory - -Example: - -ethernet@1a000000 { - compatible = "qca,ar9330-eth"; - reg = <0x1a000000 0x200>; - interrupts = <5>; - resets = <&rst 13>, <&rst 23>; - reset-names = "mac", "mdio"; - clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_MDIO>; - clock-names = "eth", "mdio"; - - phy-mode = "gmii"; -}; diff --git a/Documentation/devicetree/bindings/net/qca,ar71xx.yaml b/Documentation/devicetree/bindings/net/qca,ar71xx.yaml new file mode 100644 index 000000000000..f99a5aabe923 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,ar71xx.yaml @@ -0,0 +1,216 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qca,ar71xx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: QCA AR71XX MAC + +allOf: + - $ref: ethernet-controller.yaml# + +maintainers: + - Oleksij Rempel <o.rempel@pengutronix.de> + +properties: + compatible: + oneOf: + - items: + - enum: + - qca,ar7100-eth # Atheros AR7100 + - qca,ar7240-eth # Atheros AR7240 + - qca,ar7241-eth # Atheros AR7241 + - qca,ar7242-eth # Atheros AR7242 + - qca,ar9130-eth # Atheros AR9130 + - qca,ar9330-eth # Atheros AR9330 + - qca,ar9340-eth # Atheros AR9340 + - qca,qca9530-eth # Qualcomm Atheros QCA9530 + - qca,qca9550-eth # Qualcomm Atheros QCA9550 + - qca,qca9560-eth # Qualcomm Atheros QCA9560 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + '#address-cells': + description: number of address cells for the MDIO bus + const: 1 + + '#size-cells': + description: number of size cells on the MDIO bus + const: 0 + + clocks: + items: + - description: MAC main clock + - description: MDIO clock + + clock-names: + items: + - const: eth + - const: mdio + + resets: + items: + - description: MAC reset + - description: MDIO reset + + reset-names: + items: + - const: mac + - const: mdio + +required: + - compatible + - reg + - interrupts + - phy-mode + - clocks + - clock-names + - resets + - reset-names + +examples: + # Lager board + - | + eth0: ethernet@19000000 { + compatible = "qca,ar9330-eth"; + reg = <0x19000000 0x200>; + interrupts = <4>; + resets = <&rst 9>, <&rst 22>; + reset-names = "mac", "mdio"; + clocks = <&pll 1>, <&pll 2>; + clock-names = "eth", "mdio"; + qca,ethcfg = <ðcfg>; + phy-mode = "mii"; + phy-handle = <&phy_port4>; + }; + + eth1: ethernet@1a000000 { + compatible = "qca,ar9330-eth"; + reg = <0x1a000000 0x200>; + interrupts = <5>; + resets = <&rst 13>, <&rst 23>; + reset-names = "mac", "mdio"; + clocks = <&pll 1>, <&pll 2>; + clock-names = "eth", "mdio"; + + phy-mode = "gmii"; + + status = "disabled"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch10: switch@10 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "qca,ar9331-switch"; + reg = <0x10>; + resets = <&rst 8>; + reset-names = "switch"; + + interrupt-parent = <&miscintc>; + interrupts = <12>; + + interrupt-controller; + #interrupt-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + switch_port0: port@0 { + reg = <0x0>; + label = "cpu"; + ethernet = <ð1>; + + phy-mode = "gmii"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch_port1: port@1 { + reg = <0x1>; + phy-handle = <&phy_port0>; + phy-mode = "internal"; + + status = "disabled"; + }; + + switch_port2: port@2 { + reg = <0x2>; + phy-handle = <&phy_port1>; + phy-mode = "internal"; + + status = "disabled"; + }; + + switch_port3: port@3 { + reg = <0x3>; + phy-handle = <&phy_port2>; + phy-mode = "internal"; + + status = "disabled"; + }; + + switch_port4: port@4 { + reg = <0x4>; + phy-handle = <&phy_port3>; + phy-mode = "internal"; + + status = "disabled"; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&switch10>; + + phy_port0: phy@0 { + reg = <0x0>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port1: phy@1 { + reg = <0x1>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port2: phy@2 { + reg = <0x2>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port3: phy@3 { + reg = <0x3>; + interrupts = <0>; + status = "disabled"; + }; + + phy_port4: phy@4 { + reg = <0x4>; + interrupts = <0>; + status = "disabled"; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qcom,ipa.yaml b/Documentation/devicetree/bindings/net/qcom,ipa.yaml index 140f15245654..7b749fc04c32 100644 --- a/Documentation/devicetree/bindings/net/qcom,ipa.yaml +++ b/Documentation/devicetree/bindings/net/qcom,ipa.yaml @@ -20,7 +20,10 @@ description: The GSI is an integral part of the IPA, but it is logically isolated and has a distinct interrupt and a separately-defined address space. - See also soc/qcom/qcom,smp2p.txt and interconnect/interconnect.txt. + See also soc/qcom/qcom,smp2p.txt and interconnect/interconnect.txt. See + iommu/iommu.txt and iommu/arm,smmu.yaml for more information about SMMU + bindings. + - | -------- --------- @@ -54,6 +57,9 @@ properties: - const: ipa-shared - const: gsi + iommus: + maxItems: 1 + clocks: maxItems: 1 @@ -126,6 +132,7 @@ properties: required: - compatible + - iommus - reg - clocks - interrupts @@ -164,6 +171,7 @@ examples: modem-init; modem-remoteproc = <&mss_pil>; + iommus = <&apps_smmu 0x720 0x3>; reg = <0 0x1e40000 0 0x7000>, <0 0x1e47000 0 0x2000>, <0 0x1e04000 0 0x2c000>; diff --git a/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml new file mode 100644 index 000000000000..13555a89975f --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom,ipq4019-mdio.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/qcom,ipq4019-mdio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm IPQ40xx MDIO Controller Device Tree Bindings + +maintainers: + - Robert Marko <robert.marko@sartura.hr> + +allOf: + - $ref: "mdio.yaml#" + +properties: + compatible: + const: qcom,ipq4019-mdio + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + reg: + maxItems: 1 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +examples: + - | + mdio@90000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,ipq4019-mdio"; + reg = <0x90000 0x64>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + reg = <1>; + }; + + ethphy2: ethernet-phy@2 { + reg = <2>; + }; + + ethphy3: ethernet-phy@3 { + reg = <3>; + }; + + ethphy4: ethernet-phy@4 { + reg = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt index d2202791c1d4..709ca6d51650 100644 --- a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt @@ -10,9 +10,11 @@ device the slave device is attached to. Required properties: - compatible: should contain one of the following: * "qcom,qca6174-bt" + * "qcom,qca9377-bt" * "qcom,wcn3990-bt" * "qcom,wcn3991-bt" * "qcom,wcn3998-bt" + * "qcom,qca6390-bt" Optional properties for compatible string qcom,qca6174-bt: @@ -20,6 +22,10 @@ Optional properties for compatible string qcom,qca6174-bt: - clocks: clock provided to the controller (SUSCLK_32KHZ) - firmware-name: specify the name of nvm firmware to load +Optional properties for compatible string qcom,qca9377-bt: + + - max-speed: see Documentation/devicetree/bindings/serial/serial.yaml + Required properties for compatible string qcom,wcn399x-bt: - vddio-supply: VDD_IO supply regulator handle. diff --git a/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml b/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml new file mode 100644 index 000000000000..f15a5e5e4859 --- /dev/null +++ b/Documentation/devicetree/bindings/net/realtek-bluetooth.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/realtek-bluetooth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RTL8723BS/RTL8723CS/RTL8822CS Bluetooth Device Tree Bindings + +maintainers: + - Vasily Khoruzhick <anarsoul@gmail.com> + - Alistair Francis <alistair@alistair23.me> + +description: + RTL8723CS/RTL8723CS/RTL8822CS is WiFi + BT chip. WiFi part is connected over + SDIO, while BT is connected over serial. It speaks H5 protocol with few + extra commands to upload firmware and change module speed. + +properties: + compatible: + oneOf: + - const: "realtek,rtl8723bs-bt" + - const: "realtek,rtl8723cs-bt" + - const: "realtek,rtl8822cs-bt" + + device-wake-gpios: + maxItems: 1 + description: GPIO specifier, used to wakeup the BT module + + enable-gpios: + maxItems: 1 + description: GPIO specifier, used to enable the BT module + + host-wake-gpios: + maxItems: 1 + description: GPIO specifier, used to wakeup the host processor + +required: + - compatible + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts = <1>; + + bluetooth { + compatible = "realtek,rtl8723bs-bt"; + device-wake-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ + host-wakeup-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ + }; + }; diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt deleted file mode 100644 index 4e85fc495e87..000000000000 --- a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt +++ /dev/null @@ -1,64 +0,0 @@ -* Socionext AVE ethernet controller - -This describes the devicetree bindings for AVE ethernet controller -implemented on Socionext UniPhier SoCs. - -Required properties: - - compatible: Should be - - "socionext,uniphier-pro4-ave4" : for Pro4 SoC - - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC - - "socionext,uniphier-ld11-ave4" : for LD11 SoC - - "socionext,uniphier-ld20-ave4" : for LD20 SoC - - "socionext,uniphier-pxs3-ave4" : for PXs3 SoC - - reg: Address where registers are mapped and size of region. - - interrupts: Should contain the MAC interrupt. - - phy-mode: See ethernet.txt in the same directory. Allow to choose - "rgmii", "rmii", "mii", or "internal" according to the PHY. - The acceptable mode is SoC-dependent. - - phy-handle: Should point to the external phy device. - See ethernet.txt file in the same directory. - - clocks: A phandle to the clock for the MAC. - For Pro4 SoC, that is "socionext,uniphier-pro4-ave4", - another MAC clock, GIO bus clock and PHY clock are also required. - - clock-names: Should contain - - "ether", "ether-gb", "gio", "ether-phy" for Pro4 SoC - - "ether" for others - - resets: A phandle to the reset control for the MAC. For Pro4 SoC, - GIO bus reset is also required. - - reset-names: Should contain - - "ether", "gio" for Pro4 SoC - - "ether" for others - - socionext,syscon-phy-mode: A phandle to syscon with one argument - that configures phy mode. The argument is the ID of MAC instance. - -The MAC address will be determined using the optional properties -defined in ethernet.txt. - -Required subnode: - - mdio: A container for child nodes representing phy nodes. - See phy.txt in the same directory. - -Example: - - ether: ethernet@65000000 { - compatible = "socionext,uniphier-ld20-ave4"; - reg = <0x65000000 0x8500>; - interrupts = <0 66 4>; - phy-mode = "rgmii"; - phy-handle = <ðphy>; - clock-names = "ether"; - clocks = <&sys_clk 6>; - reset-names = "ether"; - resets = <&sys_rst 6>; - socionext,syscon-phy-mode = <&soc_glue 0>; - local-mac-address = [00 00 00 00 00 00]; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - ethphy: ethphy@1 { - reg = <1>; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.yaml b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.yaml new file mode 100644 index 000000000000..7d84a863b9b9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.yaml @@ -0,0 +1,111 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/socionext,uniphier-ave4.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext AVE ethernet controller + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +description: | + This describes the devicetree bindings for AVE ethernet controller + implemented on Socionext UniPhier SoCs. + +allOf: + - $ref: ethernet-controller.yaml# + +properties: + compatible: + enum: + - socionext,uniphier-pro4-ave4 + - socionext,uniphier-pxs2-ave4 + - socionext,uniphier-ld11-ave4 + - socionext,uniphier-ld20-ave4 + - socionext,uniphier-pxs3-ave4 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + phy-mode: true + + phy-handle: true + + mac-address: true + + local-mac-address: true + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + oneOf: + - items: # for Pro4 + - const: gio + - const: ether + - const: ether-gb + - const: ether-phy + - const: ether # for others + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + oneOf: + - items: # for Pro4 + - const: gio + - const: ether + - const: ether # for others + + socionext,syscon-phy-mode: + $ref: /schemas/types.yaml#definitions/phandle-array + description: + A phandle to syscon with one argument that configures phy mode. + The argument is the ID of MAC instance. + + mdio: + $ref: mdio.yaml# + +required: + - compatible + - reg + - interrupts + - phy-mode + - phy-handle + - clocks + - clock-names + - resets + - reset-names + - mdio + +additionalProperties: false + +examples: + - | + ether: ethernet@65000000 { + compatible = "socionext,uniphier-ld20-ave4"; + reg = <0x65000000 0x8500>; + interrupts = <0 66 4>; + phy-mode = "rgmii"; + phy-handle = <ðphy>; + clock-names = "ether"; + clocks = <&sys_clk 6>; + reset-names = "ether"; + resets = <&sys_rst 6>; + socionext,syscon-phy-mode = <&soc_glue 0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethernet-phy@1 { + reg = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt deleted file mode 100644 index 44e2a4fab29e..000000000000 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ /dev/null @@ -1,68 +0,0 @@ -* Texas Instruments - dp83867 Giga bit ethernet phy - -Required properties: - - reg - The ID number for the phy, usually a small integer - - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values. Required only if interface type is - PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID - - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h - for applicable values. Required only if interface type is - PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID - -Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock delays - will be left at their default values, as set by the PHY's pin strapping. - The default strapping will use a delay of 2.00 ns. Thus - PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no - internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree - should use "rgmii-id" if internal delays are desired as this may be - changed in future to cause "rgmii" mode to disable delays. - -Optional property: - - ti,min-output-impedance - MAC Interface Impedance control to set - the programmable output impedance to - minimum value (35 ohms). - - ti,max-output-impedance - MAC Interface Impedance control to set - the programmable output impedance to - maximum value (70 ohms). - - ti,dp83867-rxctrl-strap-quirk - This denotes the fact that the - board has RX_DV/RX_CTRL pin strapped in - mode 1 or 2. To ensure PHY operation, - there are specific actions that - software needs to take when this pin is - strapped in these modes. See data manual - for details. - - ti,clk-output-sel - Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h - for applicable values. The CLK_OUT pin can also - be disabled by this property. When omitted, the - PHY's default will be left as is. - - ti,sgmii-ref-clock-output-enable - This denotes which - SGMII configuration is used (4 or 6-wire modes). - Some MACs work with differential SGMII clock. - See data manual for details. - - - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h - for applicable values (deprecated) - - -tx-fifo-depth - As defined in the ethernet-controller.yaml. Values for - the depth can be found in dt-bindings/net/ti-dp83867.h - -rx-fifo-depth - As defined in the ethernet-controller.yaml. Values for - the depth can be found in dt-bindings/net/ti-dp83867.h - -Note: ti,min-output-impedance and ti,max-output-impedance are mutually - exclusive. When both properties are present ti,max-output-impedance - takes precedence. - -Default child nodes are standard Ethernet PHY device -nodes as described in Documentation/devicetree/bindings/net/phy.txt - -Example: - - ethernet-phy@0 { - reg = <0>; - ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; - ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; - tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; - }; - -Datasheet can be found: -http://www.ti.com/product/DP83867IR/datasheet diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.yaml b/Documentation/devicetree/bindings/net/ti,dp83867.yaml new file mode 100644 index 000000000000..554dcd7a40a9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,dp83867.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +# Copyright (C) 2019 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/ti,dp83867.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI DP83867 ethernet PHY + +allOf: + - $ref: "ethernet-controller.yaml#" + +maintainers: + - Dan Murphy <dmurphy@ti.com> + +description: | + The DP83867 device is a robust, low power, fully featured Physical Layer + transceiver with integrated PMD sublayers to support 10BASE-Te, 100BASE-TX + and 1000BASE-T Ethernet protocols. + + The DP83867 is designed for easy implementation of 10/100/1000 Mbps Ethernet + LANs. It interfaces directly to twisted pair media via an external + transformer. This device interfaces directly to the MAC layer through the + IEEE 802.3 Standard Media Independent Interface (MII), the IEEE 802.3 Gigabit + Media Independent Interface (GMII) or Reduced GMII (RGMII). + + Specifications about the charger can be found at: + https://www.ti.com/lit/gpn/dp83867ir + +properties: + reg: + maxItems: 1 + + ti,min-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a minimum value (35 ohms). + + ti,max-output-impedance: + type: boolean + description: | + MAC Interface Impedance control to set the programmable output impedance + to a maximum value (70 ohms). + Note: ti,min-output-impedance and ti,max-output-impedance are mutually + exclusive. When both properties are present ti,max-output-impedance + takes precedence. + + tx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Transmitt FIFO depth see dt-bindings/net/ti-dp83867.h for values + + rx-fifo-depth: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Receive FIFO depth see dt-bindings/net/ti-dp83867.h for values + + ti,clk-output-sel: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Muxing option for CLK_OUT pin. See dt-bindings/net/ti-dp83867.h + for applicable values. The CLK_OUT pin can also be disabled by this + property. When omitted, the PHY's default will be left as is. + + ti,rx-internal-delay: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID. + + ti,tx-internal-delay: + $ref: /schemas/types.yaml#definitions/uint32 + description: | + RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID. + + Note: If the interface type is PHY_INTERFACE_MODE_RGMII the TX/RX clock + delays will be left at their default values, as set by the PHY's pin + strapping. The default strapping will use a delay of 2.00 ns. Thus + PHY_INTERFACE_MODE_RGMII, by default, does not behave as RGMII with no + internal delay, but as PHY_INTERFACE_MODE_RGMII_ID. The device tree + should use "rgmii-id" if internal delays are desired as this may be + changed in future to cause "rgmii" mode to disable delays. + + ti,dp83867-rxctrl-strap-quirk: + type: boolean + description: | + This denotes the fact that the board has RX_DV/RX_CTRL pin strapped in + mode 1 or 2. To ensure PHY operation, there are specific actions that + software needs to take when this pin is strapped in these modes. + See data manual for details. + + ti,sgmii-ref-clock-output-enable: + type: boolean + description: | + This denotes which SGMII configuration is used (4 or 6-wire modes). + Some MACs work with differential SGMII clock. See data manual for details. + + ti,fifo-depth: + deprecated: true + $ref: /schemas/types.yaml#definitions/uint32 + description: | + Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h for applicable + values. + +required: + - reg + +examples: + - | + #include <dt-bindings/net/ti-dp83867.h> + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + ethphy0: ethernet-phy@0 { + reg = <0>; + tx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + rx-fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,max-output-impedance; + ti,clk-output-sel = <DP83867_CLK_O_SEL_CHN_A_RCLK>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83869.yaml b/Documentation/devicetree/bindings/net/ti,dp83869.yaml index 6fe3e451da8a..5b69ef03bbf7 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83869.yaml +++ b/Documentation/devicetree/bindings/net/ti,dp83869.yaml @@ -1,4 +1,4 @@ -# SPDX-License-Identifier: GPL-2.0 +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) # Copyright (C) 2019 Texas Instruments Incorporated %YAML 1.2 --- diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml index 78bf511e2892..c87395f360a6 100644 --- a/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml +++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml @@ -144,6 +144,13 @@ patternProperties: description: CPSW MDIO bus. + "^cpts@[0-9a-f]+": + type: object + allOf: + - $ref: "ti,k3-am654-cpts.yaml#" + description: + CPSW Common Platform Time Sync (CPTS) module. + required: - compatible - reg @@ -164,6 +171,8 @@ examples: #include <dt-bindings/pinctrl/k3.h> #include <dt-bindings/soc/ti,sci_pm_domain.h> #include <dt-bindings/net/ti-dp83867.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> mcu_cpsw: ethernet@46000000 { compatible = "ti,am654-cpsw-nuss"; @@ -222,4 +231,15 @@ examples: ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; }; }; + + cpts@3d000 { + compatible = "ti,am65-cpts"; + reg = <0x0 0x3d000 0x0 0x400>; + clocks = <&k3_clks 18 2>; + clock-names = "cpts"; + interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-ext-ts-inputs = <4>; + ti,cpts-periodic-outputs = <2>; + }; }; diff --git a/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml new file mode 100644 index 000000000000..50e027911dd4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml @@ -0,0 +1,145 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ti,k3-am654-cpts.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: The TI AM654x/J721E Common Platform Time Sync (CPTS) module Device Tree Bindings + +maintainers: + - Grygorii Strashko <grygorii.strashko@ti.com> + - Sekhar Nori <nsekhar@ti.com> + +description: |+ + The TI AM654x/J721E CPTS module is used to facilitate host control of time + sync operations. + Main features of CPTS module are + - selection of multiple external clock sources + - Software control of time sync events via interrupt or polling + - 64-bit timestamp mode in ns with PPM and nudge adjustment. + - hardware timestamp push inputs (HWx_TS_PUSH) + - timestamp counter compare output (TS_COMP) + - timestamp counter bit output (TS_SYNC) + - periodic Generator function outputs (TS_GENFx) + - Ethernet Enhanced Scheduled Traffic Operations (CPTS_ESTFn) (TSN) + - external hardware timestamp push inputs (HWx_TS_PUSH) timestamping + + Depending on integration it enables compliance with the IEEE 1588-2008 + standard for a precision clock synchronization protocol, Ethernet Enhanced + Scheduled Traffic Operations (CPTS_ESTFn) and PCIe Subsystem Precision Time + Measurement (PTM). + + TI AM654x/J721E SoCs has several similar CPTS modules integrated into the + different parts of the system which could be synchronized with each other + - Main CPTS + - MCU CPSW CPTS with IEEE 1588-2008 support + - PCIe subsystem CPTS for PTM support + + Depending on CPTS module integration and when CPTS is integral part of + another module (MCU CPSW for example) "compatible" and "reg" can + be omitted - parent module is fully responsible for CPTS enabling and + configuration. + +properties: + $nodename: + pattern: "^cpts@[0-9a-f]+$" + + compatible: + oneOf: + - const: ti,am65-cpts + - const: ti,j721e-cpts + + reg: + maxItems: 1 + description: + The physical base address and size of CPTS IO range + + reg-names: + items: + - const: cpts + + clocks: + description: CPTS reference clock + + clock-names: + items: + - const: cpts + + interrupts: + items: + - description: CPTS events interrupt + + interrupt-names: + items: + - const: cpts + + ti,cpts-ext-ts-inputs: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 8 + description: + Number of hardware timestamp push inputs (HWx_TS_PUSH) + + ti,cpts-periodic-outputs: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 8 + description: + Number of timestamp Generator function outputs (TS_GENFx) + + refclk-mux: + type: object + description: CPTS reference clock multiplexer clock + properties: + '#clock-cells': + const: 0 + + clocks: + maxItems: 8 + + assigned-clocks: + maxItems: 1 + + assigned-clocks-parents: + maxItems: 1 + + required: + - clocks + +required: + - compatible + - reg + - clocks + - clock-names + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + cpts@310d0000 { + compatible = "ti,am65-cpts"; + reg = <0x0 0x310d0000 0x0 0x400>; + reg-names = "cpts"; + clocks = <&main_cpts_mux>; + clock-names = "cpts"; + interrupts-extended = <&k3_irq 163 0 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-periodic-outputs = <6>; + ti,cpts-ext-ts-inputs = <8>; + + main_cpts_mux: refclk-mux { + #clock-cells = <0>; + clocks = <&k3_clks 118 5>, <&k3_clks 118 11>, + <&k3_clks 157 91>, <&k3_clks 157 77>, + <&k3_clks 157 102>, <&k3_clks 157 80>, + <&k3_clks 120 3>, <&k3_clks 121 3>; + assigned-clocks = <&main_cpts_mux>; + assigned-clock-parents = <&k3_clks 118 11>; + }; + }; + diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt index 3a76d8faaaed..ab7e7a00e534 100644 --- a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt @@ -25,6 +25,9 @@ Optional properties: - mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data - big-endian: if the radio eeprom partition is written in big-endian, specify this property +- mediatek,eeprom-merge-otp: Merge EEPROM data with OTP data. Can be used on + boards where the flash calibration data is generic and specific calibration + data should be pulled from the OTP ROM The MAC address can as well be set with corresponding optional properties defined in net/ethernet.txt. diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 71bf91f97386..65ee68efd574 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -96,6 +96,17 @@ Optional properties: - qcom,coexist-gpio-pin : gpio pin number information to support coex which will be used by wifi firmware. +* Subnodes +The ath10k wifi node can contain one optional firmware subnode. +Firmware subnode is needed when the platform does not have TustZone. +The firmware subnode must have: + +- iommus: + Usage: required + Value type: <prop-encoded-array> + Definition: A list of phandle and IOMMU specifier pairs. + + Example (to supply PCI based wifi block details): In this example, the node is defined as child node of the PCI controller. @@ -196,4 +207,7 @@ wifi@18000000 { memory-region = <&wifi_msa_mem>; iommus = <&apps_smmu 0x0040 0x1>; qcom,msa-fixed-perm; + wifi-firmware { + iommus = <&apps_iommu 0xc22 0x1>; + }; }; |