Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:

 1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
    Augusto von Dentz.

 2) Add GSO partial support to igc, from Sasha Neftin.

 3) Several cleanups and improvements to r8169 from Heiner Kallweit.

 4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
    device self-test. From Andrew Lunn.

 5) Start moving away from custom driver versions, use the globally
    defined kernel version instead, from Leon Romanovsky.

 6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.

 7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.

 8) Add sriov and vf support to hinic, from Luo bin.

 9) Support Media Redundancy Protocol (MRP) in the bridging code, from
    Horatiu Vultur.

10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.

11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
    Dubroca. Also add ipv6 support for espintcp.

12) Lots of ReST conversions of the networking documentation, from Mauro
    Carvalho Chehab.

13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
    from Doug Berger.

14) Allow to dump cgroup id and filter by it in inet_diag code, from
    Dmitry Yakunin.

15) Add infrastructure to export netlink attribute policies to
    userspace, from Johannes Berg.

16) Several optimizations to sch_fq scheduler, from Eric Dumazet.

17) Fallback to the default qdisc if qdisc init fails because otherwise
    a packet scheduler init failure will make a device inoperative. From
    Jesper Dangaard Brouer.

18) Several RISCV bpf jit optimizations, from Luke Nelson.

19) Correct the return type of the ->ndo_start_xmit() method in several
    drivers, it's netdev_tx_t but many drivers were using
    'int'. From Yunjian Wang.

20) Add an ethtool interface for PHY master/slave config, from Oleksij
    Rempel.

21) Add BPF iterators, from Yonghang Song.

22) Add cable test infrastructure, including ethool interfaces, from
    Andrew Lunn. Marvell PHY driver is the first to support this
    facility.

23) Remove zero-length arrays all over, from Gustavo A. R. Silva.

24) Calculate and maintain an explicit frame size in XDP, from Jesper
    Dangaard Brouer.

25) Add CAP_BPF, from Alexei Starovoitov.

26) Support terse dumps in the packet scheduler, from Vlad Buslov.

27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.

28) Add devm_register_netdev(), from Bartosz Golaszewski.

29) Minimize qdisc resets, from Cong Wang.

30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
    eliminate set_fs/get_fs calls. From Christoph Hellwig.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
  selftests: net: ip_defrag: ignore EPERM
  net_failover: fixed rollback in net_failover_open()
  Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
  Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
  vmxnet3: allow rx flow hash ops only when rss is enabled
  hinic: add set_channels ethtool_ops support
  selftests/bpf: Add a default $(CXX) value
  tools/bpf: Don't use $(COMPILE.c)
  bpf, selftests: Use bpf_probe_read_kernel
  s390/bpf: Use bcr 0,%0 as tail call nop filler
  s390/bpf: Maintain 8-byte stack alignment
  selftests/bpf: Fix verifier test
  selftests/bpf: Fix sample_cnt shared between two threads
  bpf, selftests: Adapt cls_redirect to call csum_level helper
  bpf: Add csum_level helper for fixing up csum levels
  bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
  sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
  crypto/chtls: IPv6 support for inline TLS
  Crypto/chcr: Fixes a coccinile check error
  Crypto/chcr: Fixes compilations warnings
  ...

1 files changed, 191 insertions, 1 deletions

diff --git a/drivers/net/dsa/ocelot/felix_vsc9959.c b/drivers/net/dsa/ocelot/felix_vsc9959.c
index 5211f05ef2fb..1dd9e348152d 100644
--- a/drivers/net/dsa/ocelot/felix_vsc9959.c
+++ b/drivers/net/dsa/ocelot/felix_vsc9959.c
@@ -3,9 +3,12 @@
  * Copyright 2018-2019 NXP Semiconductors
  */
 #include <linux/fsl/enetc_mdio.h>
+#include <soc/mscc/ocelot_qsys.h>
 #include <soc/mscc/ocelot_vcap.h>
+#include <soc/mscc/ocelot_ptp.h>
 #include <soc/mscc/ocelot_sys.h>
 #include <soc/mscc/ocelot.h>
+#include <net/pkt_sched.h>
 #include <linux/iopoll.h>
 #include <linux/pci.h>
 #include "felix.h"
@@ -27,6 +30,8 @@
 #define USXGMII_LPA_DUPLEX(lpa)		(((lpa) & GENMASK(12, 12)) >> 12)
 #define USXGMII_LPA_SPEED(lpa)		(((lpa) & GENMASK(11, 9)) >> 9)
 
+#define VSC9959_TAS_GCL_ENTRY_MAX	63
+
 enum usxgmii_speed {
 	USXGMII_SPEED_10	= 0,
 	USXGMII_SPEED_100	= 1,
@@ -202,7 +207,7 @@ static const u32 vsc9959_qsys_regmap[] = {
 	REG(QSYS_QMAXSDU_CFG_6,			0x00f62c),
 	REG(QSYS_QMAXSDU_CFG_7,			0x00f648),
 	REG(QSYS_PREEMPTION_CFG,		0x00f664),
-	REG_RESERVED(QSYS_CIR_CFG),
+	REG(QSYS_CIR_CFG,			0x000000),
 	REG(QSYS_EIR_CFG,			0x000004),
 	REG(QSYS_SE_CFG,			0x000008),
 	REG(QSYS_SE_DWRR_CFG,			0x00000c),
@@ -313,6 +318,8 @@ static const u32 vsc9959_ptp_regmap[] = {
 	REG(PTP_PIN_TOD_SEC_MSB,           0x000004),
 	REG(PTP_PIN_TOD_SEC_LSB,           0x000008),
 	REG(PTP_PIN_TOD_NSEC,              0x00000c),
+	REG(PTP_PIN_WF_HIGH_PERIOD,        0x000014),
+	REG(PTP_PIN_WF_LOW_PERIOD,         0x000018),
 	REG(PTP_CFG_MISC,                  0x0000a0),
 	REG(PTP_CLK_CFG_ADJ_CFG,           0x0000a4),
 	REG(PTP_CLK_CFG_ADJ_FREQ,          0x0000a8),
@@ -1205,6 +1212,186 @@ static void vsc9959_mdio_bus_free(struct ocelot *ocelot)
 	mdiobus_unregister(felix->imdio);
 }
 
+static void vsc9959_sched_speed_set(struct ocelot *ocelot, int port,
+				    u32 speed)
+{
+	ocelot_rmw_rix(ocelot,
+		       QSYS_TAG_CONFIG_LINK_SPEED(speed),
+		       QSYS_TAG_CONFIG_LINK_SPEED_M,
+		       QSYS_TAG_CONFIG, port);
+}
+
+static void vsc9959_new_base_time(struct ocelot *ocelot, ktime_t base_time,
+				  u64 cycle_time,
+				  struct timespec64 *new_base_ts)
+{
+	struct timespec64 ts;
+	ktime_t new_base_time;
+	ktime_t current_time;
+
+	ocelot_ptp_gettime64(&ocelot->ptp_info, &ts);
+	current_time = timespec64_to_ktime(ts);
+	new_base_time = base_time;
+
+	if (base_time < current_time) {
+		u64 nr_of_cycles = current_time - base_time;
+
+		do_div(nr_of_cycles, cycle_time);
+		new_base_time += cycle_time * (nr_of_cycles + 1);
+	}
+
+	*new_base_ts = ktime_to_timespec64(new_base_time);
+}
+
+static u32 vsc9959_tas_read_cfg_status(struct ocelot *ocelot)
+{
+	return ocelot_read(ocelot, QSYS_TAS_PARAM_CFG_CTRL);
+}
+
+static void vsc9959_tas_gcl_set(struct ocelot *ocelot, const u32 gcl_ix,
+				struct tc_taprio_sched_entry *entry)
+{
+	ocelot_write(ocelot,
+		     QSYS_GCL_CFG_REG_1_GCL_ENTRY_NUM(gcl_ix) |
+		     QSYS_GCL_CFG_REG_1_GATE_STATE(entry->gate_mask),
+		     QSYS_GCL_CFG_REG_1);
+	ocelot_write(ocelot, entry->interval, QSYS_GCL_CFG_REG_2);
+}
+
+static int vsc9959_qos_port_tas_set(struct ocelot *ocelot, int port,
+				    struct tc_taprio_qopt_offload *taprio)
+{
+	struct timespec64 base_ts;
+	int ret, i;
+	u32 val;
+
+	if (!taprio->enable) {
+		ocelot_rmw_rix(ocelot,
+			       QSYS_TAG_CONFIG_INIT_GATE_STATE(0xFF),
+			       QSYS_TAG_CONFIG_ENABLE |
+			       QSYS_TAG_CONFIG_INIT_GATE_STATE_M,
+			       QSYS_TAG_CONFIG, port);
+
+		return 0;
+	}
+
+	if (taprio->cycle_time > NSEC_PER_SEC ||
+	    taprio->cycle_time_extension >= NSEC_PER_SEC)
+		return -EINVAL;
+
+	if (taprio->num_entries > VSC9959_TAS_GCL_ENTRY_MAX)
+		return -ERANGE;
+
+	ocelot_rmw(ocelot, QSYS_TAS_PARAM_CFG_CTRL_PORT_NUM(port) |
+		   QSYS_TAS_PARAM_CFG_CTRL_ALWAYS_GUARD_BAND_SCH_Q,
+		   QSYS_TAS_PARAM_CFG_CTRL_PORT_NUM_M |
+		   QSYS_TAS_PARAM_CFG_CTRL_ALWAYS_GUARD_BAND_SCH_Q,
+		   QSYS_TAS_PARAM_CFG_CTRL);
+
+	/* Hardware errata -  Admin config could not be overwritten if
+	 * config is pending, need reset the TAS module
+	 */
+	val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_8);
+	if (val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING)
+		return  -EBUSY;
+
+	ocelot_rmw_rix(ocelot,
+		       QSYS_TAG_CONFIG_ENABLE |
+		       QSYS_TAG_CONFIG_INIT_GATE_STATE(0xFF) |
+		       QSYS_TAG_CONFIG_SCH_TRAFFIC_QUEUES(0xFF),
+		       QSYS_TAG_CONFIG_ENABLE |
+		       QSYS_TAG_CONFIG_INIT_GATE_STATE_M |
+		       QSYS_TAG_CONFIG_SCH_TRAFFIC_QUEUES_M,
+		       QSYS_TAG_CONFIG, port);
+
+	vsc9959_new_base_time(ocelot, taprio->base_time,
+			      taprio->cycle_time, &base_ts);
+	ocelot_write(ocelot, base_ts.tv_nsec, QSYS_PARAM_CFG_REG_1);
+	ocelot_write(ocelot, lower_32_bits(base_ts.tv_sec), QSYS_PARAM_CFG_REG_2);
+	val = upper_32_bits(base_ts.tv_sec);
+	ocelot_write(ocelot,
+		     QSYS_PARAM_CFG_REG_3_BASE_TIME_SEC_MSB(val) |
+		     QSYS_PARAM_CFG_REG_3_LIST_LENGTH(taprio->num_entries),
+		     QSYS_PARAM_CFG_REG_3);
+	ocelot_write(ocelot, taprio->cycle_time, QSYS_PARAM_CFG_REG_4);
+	ocelot_write(ocelot, taprio->cycle_time_extension, QSYS_PARAM_CFG_REG_5);
+
+	for (i = 0; i < taprio->num_entries; i++)
+		vsc9959_tas_gcl_set(ocelot, i, &taprio->entries[i]);
+
+	ocelot_rmw(ocelot, QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE,
+		   QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE,
+		   QSYS_TAS_PARAM_CFG_CTRL);
+
+	ret = readx_poll_timeout(vsc9959_tas_read_cfg_status, ocelot, val,
+				 !(val & QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE),
+				 10, 100000);
+
+	return ret;
+}
+
+static int vsc9959_qos_port_cbs_set(struct dsa_switch *ds, int port,
+				    struct tc_cbs_qopt_offload *cbs_qopt)
+{
+	struct ocelot *ocelot = ds->priv;
+	int port_ix = port * 8 + cbs_qopt->queue;
+	u32 rate, burst;
+
+	if (cbs_qopt->queue >= ds->num_tx_queues)
+		return -EINVAL;
+
+	if (!cbs_qopt->enable) {
+		ocelot_write_gix(ocelot, QSYS_CIR_CFG_CIR_RATE(0) |
+				 QSYS_CIR_CFG_CIR_BURST(0),
+				 QSYS_CIR_CFG, port_ix);
+
+		ocelot_rmw_gix(ocelot, 0, QSYS_SE_CFG_SE_AVB_ENA,
+			       QSYS_SE_CFG, port_ix);
+
+		return 0;
+	}
+
+	/* Rate unit is 100 kbps */
+	rate = DIV_ROUND_UP(cbs_qopt->idleslope, 100);
+	/* Avoid using zero rate */
+	rate = clamp_t(u32, rate, 1, GENMASK(14, 0));
+	/* Burst unit is 4kB */
+	burst = DIV_ROUND_UP(cbs_qopt->hicredit, 4096);
+	/* Avoid using zero burst size */
+	burst = clamp_t(u32, burst, 1, GENMASK(5, 0));
+	ocelot_write_gix(ocelot,
+			 QSYS_CIR_CFG_CIR_RATE(rate) |
+			 QSYS_CIR_CFG_CIR_BURST(burst),
+			 QSYS_CIR_CFG,
+			 port_ix);
+
+	ocelot_rmw_gix(ocelot,
+		       QSYS_SE_CFG_SE_FRM_MODE(0) |
+		       QSYS_SE_CFG_SE_AVB_ENA,
+		       QSYS_SE_CFG_SE_AVB_ENA |
+		       QSYS_SE_CFG_SE_FRM_MODE_M,
+		       QSYS_SE_CFG,
+		       port_ix);
+
+	return 0;
+}
+
+static int vsc9959_port_setup_tc(struct dsa_switch *ds, int port,
+				 enum tc_setup_type type,
+				 void *type_data)
+{
+	struct ocelot *ocelot = ds->priv;
+
+	switch (type) {
+	case TC_SETUP_QDISC_TAPRIO:
+		return vsc9959_qos_port_tas_set(ocelot, port, type_data);
+	case TC_SETUP_QDISC_CBS:
+		return vsc9959_qos_port_cbs_set(ds, port, type_data);
+	default:
+		return -EOPNOTSUPP;
+	}
+}
+
 struct felix_info felix_info_vsc9959 = {
 	.target_io_res		= vsc9959_target_io_res,
 	.port_io_res		= vsc9959_port_io_res,
@@ -1220,6 +1407,7 @@ struct felix_info felix_info_vsc9959 = {
 	.shared_queue_sz	= 128 * 1024,
 	.num_mact_rows		= 2048,
 	.num_ports		= 6,
+	.num_tx_queues		= FELIX_NUM_TC,
 	.switch_pci_bar		= 4,
 	.imdio_pci_bar		= 0,
 	.mdio_bus_alloc		= vsc9959_mdio_bus_alloc,
@@ -1228,4 +1416,6 @@ struct felix_info felix_info_vsc9959 = {
 	.pcs_an_restart		= vsc9959_pcs_an_restart,
 	.pcs_link_state		= vsc9959_pcs_link_state,
 	.prevalidate_phy_mode	= vsc9959_prevalidate_phy_mode,
+	.port_setup_tc          = vsc9959_port_setup_tc,
+	.port_sched_speed_set   = vsc9959_sched_speed_set,
 };