Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking changes from David S Miller:

 1) Remove the ipv4 routing cache.  Now lookups go directly into the FIB
    trie and use prebuilt routes cached there.

    No more garbage collection, no more rDOS attacks on the routing
    cache.  Instead we now get predictable and consistent performance,
    no matter what the pattern of traffic we service.

    This has been almost 2 years in the making.  Special thanks to
    Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
    have helped along the way.

    I'm sure that with a change of this magnitude there will be some
    kind of fallout, but such things ought the be simple to fix at this
    point.  Luckily I'm not European so I'll be around all of August to
    fix things :-)

    The major stages of this work here are each fronted by a forced
    merge commit whose commit message contains a top-level description
    of the motivations and implementation issues.

 2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
    input.

 3) TCP SYN/ACK performance tweaks from Eric Dumazet.

 4) Add namespace support for netfilter L4 conntrack helpers, from Gao
    Feng.

 5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
    Yuval Mintz.

 6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.

 7) Support for connection tracker helpers in userspace, from Pablo
    Neira Ayuso.

 8) Allow userspace driven TX load balancing functions in TEAM driver,
    from Jiri Pirko.

 9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
    embedded gotos.

10) TCP Small Queues, essentially minimize the amount of TCP data queued
    up in the packet scheduler layer.  Whereas the existing BQL (Byte
    Queue Limits) limits the pkt_sched --> netdevice queuing levels,
    this controls the TCP --> pkt_sched queueing levels.

    From Eric Dumazet.

11) Reduce the number of get_page/put_page ops done on SKB fragments,
    from Alexander Duyck.

12) Implement protection against blind resets in TCP (RFC 5961), from
    Eric Dumazet.

13) Support the client side of TCP Fast Open, basically the ability to
    send data in the SYN exchange, from Yuchung Cheng.

    Basically, the sender queues up data with a sendmsg() call using
    MSG_FASTOPEN, then they do the connect() which emits the queued up
    fastopen data.

14) Avoid all the problems we get into in TCP when timers or PMTU events
    hit a locked socket.  The TCP Small Queues changes added a
    tcp_release_cb() that allows us to queue work up to the
    release_sock() caller, and that's what we use here too.  From Eric
    Dumazet.

15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
  genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
  r8169: revert "add byte queue limit support".
  ipv4: Change rt->rt_iif encoding.
  net: Make skb->skb_iif always track skb->dev
  ipv4: Prepare for change of rt->rt_iif encoding.
  ipv4: Remove all RTCF_DIRECTSRC handliing.
  ipv4: Really ignore ICMP address requests/replies.
  decnet: Don't set RTCF_DIRECTSRC.
  net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
  ipv4: Remove redundant assignment
  rds: set correct msg_namelen
  openvswitch: potential NULL deref in sample()
  tcp: dont drop MTU reduction indications
  bnx2x: Add new 57840 device IDs
  tcp: avoid oops in tcp_metrics and reset tcpm_stamp
  niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
  niu: Fix to check for dma mapping errors.
  net: Fix references to out-of-scope variables in put_cmsg_compat()
  net: ethernet: davinci_emac: add pm_runtime support
  net: ethernet: davinci_emac: Remove unnecessary #include
  ...

1 files changed, 298 insertions, 18 deletions

diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 3cbda0851f83..7ca2ff97c368 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -15,6 +15,9 @@
  * option) any later version.
  *
  */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/kernel.h>
 #include <linux/string.h>
 #include <linux/errno.h>
@@ -32,6 +35,7 @@
 #include <linux/phy.h>
 #include <linux/timer.h>
 #include <linux/workqueue.h>
+#include <linux/mdio.h>
 
 #include <linux/atomic.h>
 #include <asm/io.h>
@@ -44,18 +48,16 @@
  */
 void phy_print_status(struct phy_device *phydev)
 {
-	pr_info("PHY: %s - Link is %s", dev_name(&phydev->dev),
-			phydev->link ? "Up" : "Down");
 	if (phydev->link)
-		printk(KERN_CONT " - %d/%s", phydev->speed,
-				DUPLEX_FULL == phydev->duplex ?
-				"Full" : "Half");
-
-	printk(KERN_CONT "\n");
+		pr_info("%s - Link is Up - %d/%s\n",
+			dev_name(&phydev->dev),
+			phydev->speed,
+			DUPLEX_FULL == phydev->duplex ? "Full" : "Half");
+	else
+		pr_info("%s - Link is Down\n", dev_name(&phydev->dev));
 }
 EXPORT_SYMBOL(phy_print_status);
 
-
 /**
  * phy_clear_interrupt - Ack the phy device's interrupt
  * @phydev: the phy_device struct
@@ -482,9 +484,8 @@ static void phy_force_reduction(struct phy_device *phydev)
 	phydev->speed = settings[idx].speed;
 	phydev->duplex = settings[idx].duplex;
 
-	pr_info("Trying %d/%s\n", phydev->speed,
-			DUPLEX_FULL == phydev->duplex ?
-			"FULL" : "HALF");
+	pr_info("Trying %d/%s\n",
+		phydev->speed, DUPLEX_FULL == phydev->duplex ? "FULL" : "HALF");
 }
 
 
@@ -598,9 +599,8 @@ int phy_start_interrupts(struct phy_device *phydev)
 				IRQF_SHARED,
 				"phy_interrupt",
 				phydev) < 0) {
-		printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n",
-				phydev->bus->name,
-				phydev->irq);
+		pr_warn("%s: Can't get IRQ %d (PHY)\n",
+			phydev->bus->name, phydev->irq);
 		phydev->irq = PHY_POLL;
 		return 0;
 	}
@@ -838,10 +838,10 @@ void phy_state_machine(struct work_struct *work)
 
 				phydev->autoneg = AUTONEG_DISABLE;
 
-				pr_info("Trying %d/%s\n", phydev->speed,
-						DUPLEX_FULL ==
-						phydev->duplex ?
-						"FULL" : "HALF");
+				pr_info("Trying %d/%s\n",
+					phydev->speed,
+					DUPLEX_FULL == phydev->duplex ?
+					"FULL" : "HALF");
 			}
 			break;
 		case PHY_NOLINK:
@@ -968,3 +968,283 @@ void phy_state_machine(struct work_struct *work)
 
 	schedule_delayed_work(&phydev->state_queue, PHY_STATE_TIME * HZ);
 }
+
+static inline void mmd_phy_indirect(struct mii_bus *bus, int prtad, int devad,
+				    int addr)
+{
+	/* Write the desired MMD Devad */
+	bus->write(bus, addr, MII_MMD_CTRL, devad);
+
+	/* Write the desired MMD register address */
+	bus->write(bus, addr, MII_MMD_DATA, prtad);
+
+	/* Select the Function : DATA with no post increment */
+	bus->write(bus, addr, MII_MMD_CTRL, (devad | MII_MMD_CTRL_NOINCR));
+}
+
+/**
+ * phy_read_mmd_indirect - reads data from the MMD registers
+ * @bus: the target MII bus
+ * @prtad: MMD Address
+ * @devad: MMD DEVAD
+ * @addr: PHY address on the MII bus
+ *
+ * Description: it reads data from the MMD registers (clause 22 to access to
+ * clause 45) of the specified phy address.
+ * To read these register we have:
+ * 1) Write reg 13 // DEVAD
+ * 2) Write reg 14 // MMD Address
+ * 3) Write reg 13 // MMD Data Command for MMD DEVAD
+ * 3) Read  reg 14 // Read MMD data
+ */
+static int phy_read_mmd_indirect(struct mii_bus *bus, int prtad, int devad,
+				 int addr)
+{
+	u32 ret;
+
+	mmd_phy_indirect(bus, prtad, devad, addr);
+
+	/* Read the content of the MMD's selected register */
+	ret = bus->read(bus, addr, MII_MMD_DATA);
+
+	return ret;
+}
+
+/**
+ * phy_write_mmd_indirect - writes data to the MMD registers
+ * @bus: the target MII bus
+ * @prtad: MMD Address
+ * @devad: MMD DEVAD
+ * @addr: PHY address on the MII bus
+ * @data: data to write in the MMD register
+ *
+ * Description: Write data from the MMD registers of the specified
+ * phy address.
+ * To write these register we have:
+ * 1) Write reg 13 // DEVAD
+ * 2) Write reg 14 // MMD Address
+ * 3) Write reg 13 // MMD Data Command for MMD DEVAD
+ * 3) Write reg 14 // Write MMD data
+ */
+static void phy_write_mmd_indirect(struct mii_bus *bus, int prtad, int devad,
+				   int addr, u32 data)
+{
+	mmd_phy_indirect(bus, prtad, devad, addr);
+
+	/* Write the data into MMD's selected register */
+	bus->write(bus, addr, MII_MMD_DATA, data);
+}
+
+static u32 phy_eee_to_adv(u16 eee_adv)
+{
+	u32 adv = 0;
+
+	if (eee_adv & MDIO_EEE_100TX)
+		adv |= ADVERTISED_100baseT_Full;
+	if (eee_adv & MDIO_EEE_1000T)
+		adv |= ADVERTISED_1000baseT_Full;
+	if (eee_adv & MDIO_EEE_10GT)
+		adv |= ADVERTISED_10000baseT_Full;
+	if (eee_adv & MDIO_EEE_1000KX)
+		adv |= ADVERTISED_1000baseKX_Full;
+	if (eee_adv & MDIO_EEE_10GKX4)
+		adv |= ADVERTISED_10000baseKX4_Full;
+	if (eee_adv & MDIO_EEE_10GKR)
+		adv |= ADVERTISED_10000baseKR_Full;
+
+	return adv;
+}
+
+static u32 phy_eee_to_supported(u16 eee_caported)
+{
+	u32 supported = 0;
+
+	if (eee_caported & MDIO_EEE_100TX)
+		supported |= SUPPORTED_100baseT_Full;
+	if (eee_caported & MDIO_EEE_1000T)
+		supported |= SUPPORTED_1000baseT_Full;
+	if (eee_caported & MDIO_EEE_10GT)
+		supported |= SUPPORTED_10000baseT_Full;
+	if (eee_caported & MDIO_EEE_1000KX)
+		supported |= SUPPORTED_1000baseKX_Full;
+	if (eee_caported & MDIO_EEE_10GKX4)
+		supported |= SUPPORTED_10000baseKX4_Full;
+	if (eee_caported & MDIO_EEE_10GKR)
+		supported |= SUPPORTED_10000baseKR_Full;
+
+	return supported;
+}
+
+static u16 phy_adv_to_eee(u32 adv)
+{
+	u16 reg = 0;
+
+	if (adv & ADVERTISED_100baseT_Full)
+		reg |= MDIO_EEE_100TX;
+	if (adv & ADVERTISED_1000baseT_Full)
+		reg |= MDIO_EEE_1000T;
+	if (adv & ADVERTISED_10000baseT_Full)
+		reg |= MDIO_EEE_10GT;
+	if (adv & ADVERTISED_1000baseKX_Full)
+		reg |= MDIO_EEE_1000KX;
+	if (adv & ADVERTISED_10000baseKX4_Full)
+		reg |= MDIO_EEE_10GKX4;
+	if (adv & ADVERTISED_10000baseKR_Full)
+		reg |= MDIO_EEE_10GKR;
+
+	return reg;
+}
+
+/**
+ * phy_init_eee - init and check the EEE feature
+ * @phydev: target phy_device struct
+ * @clk_stop_enable: PHY may stop the clock during LPI
+ *
+ * Description: it checks if the Energy-Efficient Ethernet (EEE)
+ * is supported by looking at the MMD registers 3.20 and 7.60/61
+ * and it programs the MMD register 3.0 setting the "Clock stop enable"
+ * bit if required.
+ */
+int phy_init_eee(struct phy_device *phydev, bool clk_stop_enable)
+{
+	int ret = -EPROTONOSUPPORT;
+
+	/* According to 802.3az,the EEE is supported only in full duplex-mode.
+	 * Also EEE feature is active when core is operating with MII, GMII
+	 * or RGMII.
+	 */
+	if ((phydev->duplex == DUPLEX_FULL) &&
+	    ((phydev->interface == PHY_INTERFACE_MODE_MII) ||
+	    (phydev->interface == PHY_INTERFACE_MODE_GMII) ||
+	    (phydev->interface == PHY_INTERFACE_MODE_RGMII))) {
+		int eee_lp, eee_cap, eee_adv;
+		u32 lp, cap, adv;
+		int idx, status;
+
+		/* Read phy status to properly get the right settings */
+		status = phy_read_status(phydev);
+		if (status)
+			return status;
+
+		/* First check if the EEE ability is supported */
+		eee_cap = phy_read_mmd_indirect(phydev->bus, MDIO_PCS_EEE_ABLE,
+						MDIO_MMD_PCS, phydev->addr);
+		if (eee_cap < 0)
+			return eee_cap;
+
+		cap = phy_eee_to_supported(eee_cap);
+		if (!cap)
+			goto eee_exit;
+
+		/* Check which link settings negotiated and verify it in
+		 * the EEE advertising registers.
+		 */
+		eee_lp = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_LPABLE,
+					       MDIO_MMD_AN, phydev->addr);
+		if (eee_lp < 0)
+			return eee_lp;
+
+		eee_adv = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_ADV,
+						MDIO_MMD_AN, phydev->addr);
+		if (eee_adv < 0)
+			return eee_adv;
+
+		adv = phy_eee_to_adv(eee_adv);
+		lp = phy_eee_to_adv(eee_lp);
+		idx = phy_find_setting(phydev->speed, phydev->duplex);
+		if ((lp & adv & settings[idx].setting))
+			goto eee_exit;
+
+		if (clk_stop_enable) {
+			/* Configure the PHY to stop receiving xMII
+			 * clock while it is signaling LPI.
+			 */
+			int val = phy_read_mmd_indirect(phydev->bus, MDIO_CTRL1,
+							MDIO_MMD_PCS,
+							phydev->addr);
+			if (val < 0)
+				return val;
+
+			val |= MDIO_PCS_CTRL1_CLKSTOP_EN;
+			phy_write_mmd_indirect(phydev->bus, MDIO_CTRL1,
+					       MDIO_MMD_PCS, phydev->addr, val);
+		}
+
+		ret = 0; /* EEE supported */
+	}
+
+eee_exit:
+	return ret;
+}
+EXPORT_SYMBOL(phy_init_eee);
+
+/**
+ * phy_get_eee_err - report the EEE wake error count
+ * @phydev: target phy_device struct
+ *
+ * Description: it is to report the number of time where the PHY
+ * failed to complete its normal wake sequence.
+ */
+int phy_get_eee_err(struct phy_device *phydev)
+{
+	return phy_read_mmd_indirect(phydev->bus, MDIO_PCS_EEE_WK_ERR,
+				     MDIO_MMD_PCS, phydev->addr);
+
+}
+EXPORT_SYMBOL(phy_get_eee_err);
+
+/**
+ * phy_ethtool_get_eee - get EEE supported and status
+ * @phydev: target phy_device struct
+ * @data: ethtool_eee data
+ *
+ * Description: it reportes the Supported/Advertisement/LP Advertisement
+ * capabilities.
+ */
+int phy_ethtool_get_eee(struct phy_device *phydev, struct ethtool_eee *data)
+{
+	int val;
+
+	/* Get Supported EEE */
+	val = phy_read_mmd_indirect(phydev->bus, MDIO_PCS_EEE_ABLE,
+				    MDIO_MMD_PCS, phydev->addr);
+	if (val < 0)
+		return val;
+	data->supported = phy_eee_to_supported(val);
+
+	/* Get advertisement EEE */
+	val = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_ADV,
+				    MDIO_MMD_AN, phydev->addr);
+	if (val < 0)
+		return val;
+	data->advertised = phy_eee_to_adv(val);
+
+	/* Get LP advertisement EEE */
+	val = phy_read_mmd_indirect(phydev->bus, MDIO_AN_EEE_LPABLE,
+				    MDIO_MMD_AN, phydev->addr);
+	if (val < 0)
+		return val;
+	data->lp_advertised = phy_eee_to_adv(val);
+
+	return 0;
+}
+EXPORT_SYMBOL(phy_ethtool_get_eee);
+
+/**
+ * phy_ethtool_set_eee - set EEE supported and status
+ * @phydev: target phy_device struct
+ * @data: ethtool_eee data
+ *
+ * Description: it is to program the Advertisement EEE register.
+ */
+int phy_ethtool_set_eee(struct phy_device *phydev, struct ethtool_eee *data)
+{
+	int val;
+
+	val = phy_adv_to_eee(data->advertised);
+	phy_write_mmd_indirect(phydev->bus, MDIO_AN_EEE_ADV, MDIO_MMD_AN,
+			       phydev->addr, val);
+
+	return 0;
+}
+EXPORT_SYMBOL(phy_ethtool_set_eee);