diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display')
41 files changed, 1772 insertions, 187 deletions
diff --git a/Documentation/devicetree/bindings/display/arm,malidp.txt b/Documentation/devicetree/bindings/display/arm,malidp.txt new file mode 100644 index 000000000000..2f7870983ef1 --- /dev/null +++ b/Documentation/devicetree/bindings/display/arm,malidp.txt @@ -0,0 +1,65 @@ +ARM Mali-DP + +The following bindings apply to a family of Display Processors sold as +licensable IP by ARM Ltd. The bindings describe the Mali DP500, DP550 and +DP650 processors that offer multiple composition layers, support for +rotation and scaling output. + +Required properties: + - compatible: should be one of + "arm,mali-dp500" + "arm,mali-dp550" + "arm,mali-dp650" + depending on the particular implementation present in the hardware + - reg: Physical base address and size of the block of registers used by + the processor. + - interrupts: Interrupt list, as defined in ../interrupt-controller/interrupts.txt, + interrupt client nodes. + - interrupt-names: name of the engine inside the processor that will + use the corresponding interrupt. Should be one of "DE" or "SE". + - clocks: A list of phandle + clock-specifier pairs, one for each entry + in 'clock-names' + - clock-names: A list of clock names. It should contain: + - "pclk": for the APB interface clock + - "aclk": for the AXI interface clock + - "mclk": for the main processor clock + - "pxlclk": for the pixel clock feeding the output PLL of the processor. + - arm,malidp-output-port-lines: Array of u8 values describing the number + of output lines per channel (R, G and B). + +Required sub-nodes: + - port: The Mali DP connection to an encoder input port. The connection + is modelled using the OF graph bindings specified in + Documentation/devicetree/bindings/graph.txt + +Optional properties: + - memory-region: phandle to a node describing memory (see + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) + to be used for the framebuffer; if not present, the framebuffer may + be located anywhere in memory. + + +Example: + +/ { + ... + + dp0: malidp@6f200000 { + compatible = "arm,mali-dp650"; + reg = <0 0x6f200000 0 0x20000>; + memory-region = <&display_reserved>; + interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>, + <0 168 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "DE", "SE"; + clocks = <&oscclk2>, <&fpgaosc0>, <&fpgaosc1>, <&fpgaosc1>; + clock-names = "pxlclk", "mclk", "aclk", "pclk"; + arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; + port { + dp0_output: endpoint { + remote-endpoint = <&tda998x_2_input>; + }; + }; + }; + + ... +}; diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt index 9f97df4d5152..a5ea451e67fc 100644 --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt @@ -35,12 +35,22 @@ Optional properties for HDMI: as an interrupt/status bit in the HDMI controller itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt +Required properties for DPI: +- compatible: Should be "brcm,bcm2835-dpi" +- reg: Physical base address and length of the registers +- clocks: a) core: The core clock the unit runs on + b) pixel: The pixel clock that feeds the pixelvalve +- port: Port node with a single endpoint connecting to the panel + device, as defined in [1] + Required properties for V3D: - compatible: Should be "brcm,bcm2835-v3d" - reg: Physical base address and length of the V3D's registers - interrupts: The interrupt number See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +[1] Documentation/devicetree/bindings/media/video-interfaces.txt + Example: pixelvalve@7e807000 { compatible = "brcm,bcm2835-pixelvalve2"; @@ -66,6 +76,22 @@ hdmi: hdmi@7e902000 { clock-names = "pixel", "hdmi"; }; +dpi: dpi@7e208000 { + compatible = "brcm,bcm2835-dpi"; + reg = <0x7e208000 0x8c>; + clocks = <&clocks BCM2835_CLOCK_VPU>, + <&clocks BCM2835_CLOCK_DPI>; + clock-names = "core", "pixel"; + #address-cells = <1>; + #size-cells = <0>; + + port { + dpi_out: endpoint@0 { + remote-endpoint = <&panel_in>; + }; + }; +}; + v3d: v3d@7ec00000 { compatible = "brcm,bcm2835-v3d"; reg = <0x7ec00000 0x1000>; @@ -75,3 +101,13 @@ v3d: v3d@7ec00000 { vc4: gpu { compatible = "brcm,bcm2835-vc4"; }; + +panel: panel { + compatible = "ontat,yx700wv03", "simple-panel"; + + port { + panel_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 96c25ee01501..6532a59c9b43 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -1,13 +1,19 @@ -Analog Device ADV7511(W)/13 HDMI Encoders +Analog Device ADV7511(W)/13/33 HDMI Encoders ----------------------------------------- -The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters +The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, -S/PDIF, CEC and HDCP. +S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while +the others support RGB interface. Required properties: -- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513" +- compatible: Should be one of: + "adi,adv7511" + "adi,adv7511w" + "adi,adv7513" + "adi,adv7533" + - reg: I2C slave address The ADV7511 supports a large number of input data formats that differ by their @@ -32,6 +38,11 @@ The following input format properties are required except in "rgb 1x" and - adi,input-justification: The input bit justification ("left", "evenly", "right"). +The following properties are required for ADV7533: + +- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should + be one of 1, 2, 3 or 4. + Optional properties: - interrupts: Specifier for the ADV7511 interrupt @@ -42,13 +53,18 @@ Optional properties: - adi,embedded-sync: The input uses synchronization signals embedded in the data stream (similar to BT.656). Defaults to separate H/V synchronization signals. +- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing + generator. The chip will rely on the sync signals in the DSI data lanes, + rather than generate its own timings for HDMI output. Required nodes: The ADV7511 has two video ports. Their connections are modelled using the OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. -- Video port 0 for the RGB or YUV input +- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the + remote endpoint phandle should be a reference to a valid mipi_dsi_host device + node. - Video port 1 for the HDMI output diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt new file mode 100644 index 000000000000..4a0f4f7682ad --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt @@ -0,0 +1,53 @@ +Analogix Display Port bridge bindings + +Required properties for dp-controller: + -compatible: + platform specific such as: + * "samsung,exynos5-dp" + * "rockchip,rk3288-dp" + * "rockchip,rk3399-edp" + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". + -interrupt-parent: + phandle to Interrupt combiner node. + -phys: + from general PHY binding: the phandle for the PHY device. + -phy-names: + from general PHY binding: Should be "dp". + +Optional properties for dp-controller: + -force-hpd: + Indicate driver need force hpd when hpd detect failed, this + is used for some eDP screen which don't have hpd signal. + -hpd-gpios: + Hotplug detect GPIO. + Indicates which GPIO should be used for hotplug detection + -port@[X]: SoC specific port nodes with endpoint definitions as defined + in Documentation/devicetree/bindings/media/video-interfaces.txt, + please refer to the SoC specific binding document: + * Documentation/devicetree/bindings/display/exynos/exynos_dp.txt + * Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt +------------------------------------------------------------------------------- + +Example: + + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; + + phys = <&dp_phy>; + phy-names = "dp"; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt new file mode 100644 index 000000000000..56a3e68ccb80 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt @@ -0,0 +1,35 @@ +sii902x HDMI bridge bindings + +Required properties: + - compatible: "sil,sii9022" + - reg: i2c address of the bridge + +Optional properties: + - interrupts-extended or interrupt-parent + interrupts: describe + the interrupt line used to inform the host about hotplug events. + - reset-gpios: OF device-tree gpio specification for RST_N pin. + +Optional subnodes: + - video input: this subnode can contain a video input port node + to connect the bridge to a display controller output (See this + documentation [1]). + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + hdmi-bridge@39 { + compatible = "sil,sii9022"; + reg = <0x39>; + reset-gpios = <&pioA 1 0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + bridge_in: endpoint { + remote-endpoint = <&dc_out>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt new file mode 100644 index 000000000000..e3f6aa6a214d --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt @@ -0,0 +1,53 @@ +Toshiba TC358767 eDP bridge bindings + +Required properties: + - compatible: "toshiba,tc358767" + - reg: i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins + - clock-names: should be "ref" + - clocks: OF device-tree clock specification for refclk input. The reference + clock rate must be 13 MHz, 19.2 MHz, 26 MHz, or 38.4 MHz. + +Optional properties: + - shutdown-gpios: OF device-tree gpio specification for SD pin + (active high shutdown input) + - reset-gpios: OF device-tree gpio specification for RSTX pin + (active low system reset) + - ports: the ports node can contain video interface port nodes to connect + to a DPI/DSI source and to an eDP/DP sink according to [1][2]: + - port@0: DSI input port + - port@1: DPI input port + - port@2: eDP/DP output port + +[1]: Documentation/devicetree/bindings/graph.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + edp-bridge@68 { + compatible = "toshiba,tc358767"; + reg = <0x68>; + shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>; + clock-names = "ref"; + clocks = <&edp_refclk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + bridge_in: endpoint { + remote-endpoint = <&dpi_out>; + }; + }; + + port@2 { + reg = <2>; + + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt index d685be898d0c..e9c65746e2f1 100644 --- a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt +++ b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt @@ -1,7 +1,7 @@ * Currus Logic CLPS711X Framebuffer Required properties: -- compatible: Shall contain "cirrus,clps711x-fb". +- compatible: Shall contain "cirrus,ep7209-fb". - reg : Physical base address and length of the controller's registers + location and size of the framebuffer memory. - clocks : phandle + clock specifier pair of the FB reference clock. @@ -18,7 +18,7 @@ Optional properties: Example: fb: fb@800002c0 { - compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb"; + compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb"; reg = <0x800002c0 0xd44>, <0x60000000 0xc000>; clocks = <&clks 2>; lcd-supply = <®5v0>; diff --git a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt index acd5668b1ce1..508aee461e0d 100644 --- a/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt +++ b/Documentation/devicetree/bindings/display/connector/hdmi-connector.txt @@ -8,6 +8,7 @@ Required properties: Optional properties: - label: a symbolic name for the connector - hpd-gpios: HPD GPIO number +- ddc-i2c-bus: phandle link to the I2C controller used for DDC EDID probing Required nodes: - Video port for HDMI input diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index 377afbf5122a..c9fd7b3807e7 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -5,7 +5,8 @@ Exynos series of SoCs which transfers the image data from a video memory buffer to an external LCD interface. Required properties: -- compatible: value should be "samsung,exynos5433-decon"; +- compatible: value should be one of: + "samsung,exynos5433-decon", "samsung,exynos5433-decon-tv"; - reg: physical base address and length of the DECON registers set. - interrupts: should contain a list of all DECON IP block interrupts in the order: VSYNC, LCD_SYSTEM. The interrupt specifier format @@ -16,7 +17,7 @@ Required properties: - clocks: must include clock specifiers corresponding to entries in the clock-names property. - clock-names: list of clock names sorted in the same order as the clocks - property. Must contain "aclk_decon", "aclk_smmu_decon0x", + property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", "sclk_decon_eclk" - ports: contains a port which is connected to mic node. address-cells and diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt index fe4a7a2dea9c..ade5d8eebf85 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -1,20 +1,3 @@ -Device-Tree bindings for Samsung Exynos Embedded DisplayPort Transmitter(eDP) - -DisplayPort is industry standard to accommodate the growing board adoption -of digital display technology within the PC and CE industries. -It consolidates the internal and external connection methods to reduce device -complexity and cost. It also supports necessary features for important cross -industry applications and provides performance scalability to enable the next -generation of displays that feature higher color depths, refresh rates, and -display resolutions. - -eDP (embedded display port) device is compliant with Embedded DisplayPort -standard as follows, -- DisplayPort standard 1.1a for Exynos5250 and Exynos5260. -- DisplayPort standard 1.3 for Exynos5422s and Exynos5800. - -eDP resides between FIMD and panel or FIMD and bridge such as LVDS. - The Exynos display port interface should be configured based on the type of panel connected to it. @@ -48,26 +31,6 @@ Required properties for dp-controller: from general PHY binding: the phandle for the PHY device. -phy-names: from general PHY binding: Should be "dp". - -samsung,color-space: - input video data format. - COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 - -samsung,dynamic-range: - dynamic range for input video data. - VESA = 0, CEA = 1 - -samsung,ycbcr-coeff: - YCbCr co-efficients for input video. - COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 - -samsung,color-depth: - number of bits per colour component. - COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 - -samsung,link-rate: - link rate supported by the panel. - LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A - -samsung,lane-count: - number of lanes supported by the panel. - LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4 - - display-timings: timings for the connected panel as described by - Documentation/devicetree/bindings/display/display-timing.txt Optional properties for dp-controller: -interlaced: @@ -83,17 +46,31 @@ Optional properties for dp-controller: Hotplug detect GPIO. Indicates which GPIO should be used for hotplug detection -Video interfaces: - Device node can contain video interface port nodes according to [1]. - The following are properties specific to those nodes: - - endpoint node connected to bridge or panel node: - - remote-endpoint: specifies the endpoint in panel or bridge node. - This node is required in all kinds of exynos dp - to represent the connection between dp and bridge - or dp and panel. - -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + -video interfaces: Device node can contain video interface port + nodes according to [1]. + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/display/panel/display-timing.txt + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/display/bridge/analogix_dp.txt + -phys (required) + -phy-names (required) + -hpd-gpios (optional) + force-hpd (optional) + +Deprecated properties for DisplayPort: +-interlaced: deprecated prop that can parsed from drm_display_mode. +-vsync-active-high: deprecated prop that can parsed from drm_display_mode. +-hsync-active-high: deprecated prop that can parsed from drm_display_mode. +-samsung,ycbcr-coeff: deprecated prop that can parsed from drm_display_mode. +-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode. +-samsung,color-space: deprecated prop that can parsed from drm_display_info. +-samsung,color-depth: deprecated prop that can parsed from drm_display_info. +-samsung,link-rate: deprecated prop that can reading from monitor by dpcd method. +-samsung,lane-count: deprecated prop that can reading from monitor by dpcd method. +-samsung,hpd-gpio: deprecated name for hpd-gpios. + +------------------------------------------------------------------------------- Example: @@ -112,13 +89,6 @@ SOC specific portion: Board Specific portion: dp-controller { - samsung,color-space = <0>; - samsung,dynamic-range = <0>; - samsung,ycbcr-coeff = <0>; - samsung,color-depth = <1>; - samsung,link-rate = <0x0a>; - samsung,lane-count = <4>; - display-timings { native-mode = <&lcd_timing>; lcd_timing: 1366x768 { @@ -135,18 +105,9 @@ Board Specific portion: }; ports { - port { + port@0 { dp_out: endpoint { - remote-endpoint = <&dp_in>; - }; - }; - }; - - panel { - ... - port { - dp_in: endpoint { - remote-endpoint = <&dp_out>; + remote-endpoint = <&bridge_in>; }; }; }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt index 22756b3dede2..a78265993665 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -41,7 +41,7 @@ Video interfaces: endpoint node connected from mic node (reg = 0): - remote-endpoint: specifies the endpoint in mic node. This node is required for Exynos5433 mipi dsi. So mic can access to panel node - thoughout this dsi node. + throughout this dsi node. endpoint node connected to panel node (reg = 1): - remote-endpoint: specifies the endpoint in panel node. This node is required in all kinds of exynos mipi dsi to represent diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt index d474f59be6d6..a2ec4c1c9382 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos_hdmi.txt @@ -5,6 +5,7 @@ Required properties: 1) "samsung,exynos4210-hdmi" 2) "samsung,exynos4212-hdmi" 3) "samsung,exynos5420-hdmi" + 4) "samsung,exynos5433-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -12,6 +13,11 @@ Required properties: a) phandle of the gpio controller node. b) pin number within the gpio controller. c) optional flags and pull up/down. +- ddc: phandle to the hdmi ddc node +- phy: phandle to the hdmi phy node +- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 4210, 4212, 5420 and 5433: - clocks: list of clock IDs from SoC clock driver. a) hdmi: Gate of HDMI IP bus clock. b) sclk_hdmi: Gate of HDMI special clock. @@ -25,9 +31,24 @@ Required properties: sclk_pixel. - clock-names: aliases as per driver requirements for above clock IDs: "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy" and "mout_hdmi". -- ddc: phandle to the hdmi ddc node -- phy: phandle to the hdmi phy node -- samsung,syscon-phandle: phandle for system controller node for PMU. + +Required properties for Exynos 5433: +- clocks: list of clock specifiers according to common clock bindings. + a) hdmi_pclk: Gate of HDMI IP APB bus. + b) hdmi_i_pclk: Gate of HDMI-PHY IP APB bus. + d) i_tmds_clk: Gate of HDMI TMDS clock. + e) i_pixel_clk: Gate of HDMI pixel clock. + f) i_spdif_clk: Gate of HDMI SPDIF clock. + g) oscclk: Oscillator clock, used as parent of following *_user clocks + in case HDMI-PHY is not operational. + h) tmds_clko: TMDS clock generated by HDMI-PHY. + i) tmds_clko_user: MUX used to switch between oscclk and tmds_clko, + respectively if HDMI-PHY is off and operational. + j) pixel_clko: Pixel clock generated by HDMI-PHY. + k) pixel_clko_user: MUX used to switch between oscclk and pixel_clko, + respectively if HDMI-PHY is off and operational. +- clock-names: aliases for above clock specfiers. +- samsung,sysreg: handle to syscon used to control the system registers. Example: diff --git a/Documentation/devicetree/bindings/display/fsl,dcu.txt b/Documentation/devicetree/bindings/display/fsl,dcu.txt index ebf1be9ae393..63ec2a624aa9 100644 --- a/Documentation/devicetree/bindings/display/fsl,dcu.txt +++ b/Documentation/devicetree/bindings/display/fsl,dcu.txt @@ -6,17 +6,29 @@ Required properties: * "fsl,vf610-dcu". - reg: Address and length of the register set for dcu. -- clocks: From common clock binding: handle to dcu clock. -- clock-names: From common clock binding: Shall be "dcu". +- clocks: Handle to "dcu" and "pix" clock (in the order below) + This can be the same clock (e.g. LS1021a) + See ../clocks/clock-bindings.txt for details. +- clock-names: Should be "dcu" and "pix" + See ../clocks/clock-bindings.txt for details. - big-endian Boolean property, LS1021A DCU registers are big-endian. -- fsl,panel: The phandle to panel node. +- port Video port for the panel output + +Optional properties: +- fsl,tcon: The phandle to the timing controller node. Examples: dcu: dcu@2ce0000 { compatible = "fsl,ls1021a-dcu"; reg = <0x0 0x2ce0000 0x0 0x10000>; - clocks = <&platform_clk 0>; - clock-names = "dcu"; + clocks = <&platform_clk 0>, <&platform_clk 0>; + clock-names = "dcu", "pix"; big-endian; - fsl,panel = <&panel>; + fsl,tcon = <&tcon>; + + port { + dcu_out: endpoint { + remote-endpoint = <&panel_out>; + }; + }; }; diff --git a/Documentation/devicetree/bindings/display/fsl,tcon.txt b/Documentation/devicetree/bindings/display/fsl,tcon.txt new file mode 100644 index 000000000000..6fa4ab668db5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/fsl,tcon.txt @@ -0,0 +1,18 @@ +Device Tree bindings for Freescale TCON Driver + +Required properties: +- compatible: Should be one of + * "fsl,vf610-tcon". + +- reg: Address and length of the register set for tcon. +- clocks: From common clock binding: handle to tcon ipg clock. +- clock-names: From common clock binding: Shall be "ipg". + +Examples: +timing-controller@4003d000 { + compatible = "fsl,vf610-tcon"; + reg = <0x4003d000 0x1000>; + clocks = <&clks VF610_CLK_TCON0>; + clock-names = "ipg"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt new file mode 100644 index 000000000000..d270bfe4e4e0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/dw-dsi.txt @@ -0,0 +1,72 @@ +Device-Tree bindings for DesignWare DSI Host Controller v1.20a driver + +A DSI Host Controller resides in the middle of display controller and external +HDMI converter or panel. + +Required properties: +- compatible: value should be "hisilicon,hi6220-dsi". +- reg: physical base address and length of dsi controller's registers. +- clocks: contains APB clock phandle + clock-specifier pair. +- clock-names: should be "pclk". +- ports: contains DSI controller input and output sub port. + The input port connects to ADE output port with the reg value "0". + The output port with the reg value "1", it could connect to panel or + any other bridge endpoints. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +A example of HiKey board hi6220 SoC and board specific DT entry: +Example: + +SoC specific: + dsi: dsi@f4107800 { + compatible = "hisilicon,hi6220-dsi"; + reg = <0x0 0xf4107800 0x0 0x100>; + clocks = <&media_ctrl HI6220_DSI_PCLK>; + clock-names = "pclk"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* 0 for input port */ + port@0 { + reg = <0>; + dsi_in: endpoint { + remote-endpoint = <&ade_out>; + }; + }; + }; + }; + + +Board specific: + &dsi { + status = "ok"; + + ports { + /* 1 for output port */ + port@1 { + reg = <1>; + + dsi_out0: endpoint@0 { + remote-endpoint = <&adv7533_in>; + }; + }; + }; + }; + + &i2c2 { + ... + + adv7533: adv7533@39 { + ... + + port { + adv7533_in: endpoint { + remote-endpoint = <&dsi_out0>; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt new file mode 100644 index 000000000000..38dc9d60eef8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/hisilicon/hisi-ade.txt @@ -0,0 +1,64 @@ +Device-Tree bindings for hisilicon ADE display controller driver + +ADE (Advanced Display Engine) is the display controller which grab image +data from memory, do composition, do post image processing, generate RGB +timing stream and transfer to DSI. + +Required properties: +- compatible: value should be "hisilicon,hi6220-ade". +- reg: physical base address and length of the ADE controller's registers. +- hisilicon,noc-syscon: ADE NOC QoS syscon. +- resets: The ADE reset controller node. +- interrupt: the ldi vblank interrupt number used. +- clocks: a list of phandle + clock-specifier pairs, one for each entry + in clock-names. +- clock-names: should contain: + "clk_ade_core" for the ADE core clock. + "clk_codec_jpeg" for the media NOC QoS clock, which use the same clock with + jpeg codec. + "clk_ade_pix" for the ADE pixel clok. +- assigned-clocks: Should contain "clk_ade_core" and "clk_codec_jpeg" clocks' + phandle + clock-specifier pairs. +- assigned-clock-rates: clock rates, one for each entry in assigned-clocks. + The rate of "clk_ade_core" could be "360000000" or "180000000"; + The rate of "clk_codec_jpeg" could be or less than "1440000000". + These rate values could be configured according to performance and power + consumption. +- port: the output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected DSI input endpoint. + See Documentation/devicetree/bindings/graph.txt for more device graph info. + +Optional properties: +- dma-coherent: Present if dma operations are coherent. + + +A example of HiKey board hi6220 SoC specific DT entry: +Example: + + ade: ade@f4100000 { + compatible = "hisilicon,hi6220-ade"; + reg = <0x0 0xf4100000 0x0 0x7800>; + reg-names = "ade_base"; + hisilicon,noc-syscon = <&medianoc_ade>; + resets = <&media_ctrl MEDIA_ADE>; + interrupts = <0 115 4>; /* ldi interrupt */ + + clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>, + <&media_ctrl HI6220_ADE_PIX_SRC>; + /*clock name*/ + clock-names = "clk_ade_core", + "clk_codec_jpeg", + "clk_ade_pix"; + + assigned-clocks = <&media_ctrl HI6220_ADE_CORE>, + <&media_ctrl HI6220_CODEC_JPEG>; + assigned-clock-rates = <360000000>, <288000000>; + dma-coherent; + + port { + ade_out: endpoint { + remote-endpoint = <&dsi_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt index 0a175d991b52..a407462c885e 100644 --- a/Documentation/devicetree/bindings/display/imx/ldb.txt +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -62,6 +62,7 @@ Required properties: display-timings are used instead. Optional properties (required if display-timings are used): + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing - display-timings : A node that describes the display timings as defined in Documentation/devicetree/bindings/display/display-timing.txt. - fsl,data-mapping : should be "spwg" or "jeida" diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt new file mode 100644 index 000000000000..db6e77edbea8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,disp.txt @@ -0,0 +1,203 @@ +Mediatek display subsystem +========================== + +The Mediatek display subsystem consists of various DISP function blocks in the +MMSYS register space. The connections between them can be configured by output +and input selectors in the MMSYS_CONFIG register space. Pixel clock and start +of frame signal are distributed to the other function blocks by a DISP_MUTEX +function block. + +All DISP device tree nodes must be siblings to the central MMSYS_CONFIG node. +For a description of the MMSYS_CONFIG binding, see +Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt. + +DISP function blocks +==================== + +A display stream starts at a source function block that reads pixel data from +memory and ends with a sink function block that drives pixels on a display +interface, or writes pixels back to memory. All DISP function blocks have +their own register space, interrupt, and clock gate. The blocks that can +access memory additionally have to list the IOMMU and local arbiter they are +connected to. + +For a description of the display interface sink function blocks, see +Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt and +Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt. + +Required properties (all function blocks): +- compatible: "mediatek,<chip>-disp-<function>", one of + "mediatek,<chip>-disp-ovl" - overlay (4 layers, blending, csc) + "mediatek,<chip>-disp-rdma" - read DMA / line buffer + "mediatek,<chip>-disp-wdma" - write DMA + "mediatek,<chip>-disp-color" - color processor + "mediatek,<chip>-disp-aal" - adaptive ambient light controller + "mediatek,<chip>-disp-gamma" - gamma correction + "mediatek,<chip>-disp-merge" - merge streams from two RDMA sources + "mediatek,<chip>-disp-split" - split stream to two encoders + "mediatek,<chip>-disp-ufoe" - data compression engine + "mediatek,<chip>-dsi" - DSI controller, see mediatek,dsi.txt + "mediatek,<chip>-dpi" - DPI controller, see mediatek,dpi.txt + "mediatek,<chip>-disp-mutex" - display mutex + "mediatek,<chip>-disp-od" - overdrive +- reg: Physical base address and length of the function block register space +- interrupts: The interrupt signal from the function block (required, except for + merge and split function blocks). +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. + For most function blocks this is just a single clock input. Only the DSI and + DPI controller nodes have multiple clock inputs. These are documented in + mediatek,dsi.txt and mediatek,dpi.txt, respectively. + +Required properties (DMA function blocks): +- compatible: Should be one of + "mediatek,<chip>-disp-ovl" + "mediatek,<chip>-disp-rdma" + "mediatek,<chip>-disp-wdma" +- larb: Should contain a phandle pointing to the local arbiter device as defined + in Documentation/devicetree/bindings/soc/mediatek/mediatek,smi-larb.txt +- iommus: Should point to the respective IOMMU block with master port as + argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt + for details. + +Examples: + +mmsys: clock-controller@14000000 { + compatible = "mediatek,mt8173-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + #clock-cells = <1>; +}; + +ovl0: ovl@1400c000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400c000 0 0x1000>; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL0>; + iommus = <&iommu M4U_PORT_DISP_OVL0>; + mediatek,larb = <&larb0>; +}; + +ovl1: ovl@1400d000 { + compatible = "mediatek,mt8173-disp-ovl"; + reg = <0 0x1400d000 0 0x1000>; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OVL1>; + iommus = <&iommu M4U_PORT_DISP_OVL1>; + mediatek,larb = <&larb4>; +}; + +rdma0: rdma@1400e000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400e000 0 0x1000>; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA0>; + iommus = <&iommu M4U_PORT_DISP_RDMA0>; + mediatek,larb = <&larb0>; +}; + +rdma1: rdma@1400f000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x1400f000 0 0x1000>; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA1>; + iommus = <&iommu M4U_PORT_DISP_RDMA1>; + mediatek,larb = <&larb4>; +}; + +rdma2: rdma@14010000 { + compatible = "mediatek,mt8173-disp-rdma"; + reg = <0 0x14010000 0 0x1000>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_RDMA2>; + iommus = <&iommu M4U_PORT_DISP_RDMA2>; + mediatek,larb = <&larb4>; +}; + +wdma0: wdma@14011000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14011000 0 0x1000>; + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA0>; + iommus = <&iommu M4U_PORT_DISP_WDMA0>; + mediatek,larb = <&larb0>; +}; + +wdma1: wdma@14012000 { + compatible = "mediatek,mt8173-disp-wdma"; + reg = <0 0x14012000 0 0x1000>; + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_WDMA1>; + iommus = <&iommu M4U_PORT_DISP_WDMA1>; + mediatek,larb = <&larb4>; +}; + +color0: color@14013000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14013000 0 0x1000>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR0>; +}; + +color1: color@14014000 { + compatible = "mediatek,mt8173-disp-color"; + reg = <0 0x14014000 0 0x1000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_COLOR1>; +}; + +aal@14015000 { + compatible = "mediatek,mt8173-disp-aal"; + reg = <0 0x14015000 0 0x1000>; + interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_AAL>; +}; + +gamma@14016000 { + compatible = "mediatek,mt8173-disp-gamma"; + reg = <0 0x14016000 0 0x1000>; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_GAMMA>; +}; + +ufoe@1401a000 { + compatible = "mediatek,mt8173-disp-ufoe"; + reg = <0 0x1401a000 0 0x1000>; + interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_UFOE>; +}; + +dsi0: dsi@1401b000 { + /* See mediatek,dsi.txt for details */ +}; + +dpi0: dpi@1401d000 { + /* See mediatek,dpi.txt for details */ +}; + +mutex: mutex@14020000 { + compatible = "mediatek,mt8173-disp-mutex"; + reg = <0 0x14020000 0 0x1000>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MUTEX_32K>; +}; + +od@14023000 { + compatible = "mediatek,mt8173-disp-od"; + reg = <0 0x14023000 0 0x1000>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_DISP_OD>; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt new file mode 100644 index 000000000000..b6a7e7397b8b --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt @@ -0,0 +1,35 @@ +Mediatek DPI Device +=================== + +The Mediatek DPI function block is a sink of the display subsystem and +provides 8-bit RGB/YUV444 or 8/10/10-bit YUV422 pixel data on a parallel +output bus. + +Required properties: +- compatible: "mediatek,<chip>-dpi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "engine", and "pll" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached HDMI or LVDS encoder chip. + +Example: + +dpi0: dpi@1401d000 { + compatible = "mediatek,mt8173-dpi"; + reg = <0 0x1401d000 0 0x1000>; + interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_DPI_PIXEL>, + <&mmsys CLK_MM_DPI_ENGINE>, + <&apmixedsys CLK_APMIXED_TVDPLL>; + clock-names = "pixel", "engine", "pll"; + + port { + dpi0_out: endpoint { + remote-endpoint = <&hdmi0_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt new file mode 100644 index 000000000000..2b1585a34b85 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt @@ -0,0 +1,60 @@ +Mediatek DSI Device +=================== + +The Mediatek DSI function block is a sink of the display subsystem and can +drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual- +channel output. + +Required properties: +- compatible: "mediatek,<chip>-dsi" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "engine", "digital", and "hs" +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached DSI panel or DSI-to-eDP encoder chip. + +MIPI TX Configuration Module +============================ + +The MIPI TX configuration module controls the MIPI D-PHY. + +Required properties: +- compatible: "mediatek,<chip>-mipi-tx" +- reg: Physical base address and length of the controller's registers +- clocks: PLL reference clock +- clock-output-names: name of the output clock line to the DSI encoder +- #clock-cells: must be <0>; +- #phy-cells: must be <0>. + +Example: + +mipi_tx0: mipi-dphy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10215000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +dsi0: dsi@1401b000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401b000 0 0x1000>; + interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt new file mode 100644 index 000000000000..7b124242b0c5 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt @@ -0,0 +1,148 @@ +Mediatek HDMI Encoder +===================== + +The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from +its parallel input. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi". +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "pixel", "pll", "bclk", and "spdif". +- phys: phandle link to the HDMI PHY node. + See Documentation/devicetree/bindings/phy/phy-bindings.txt for details. +- phy-names: must contain "hdmi" +- mediatek,syscon-hdmi: phandle link and register offset to the system + configuration registers. For mt8173 this must be offset 0x900 into the + MMSYS_CONFIG region: <&mmsys 0x900>. +- ports: A node containing input and output port nodes with endpoint + definitions as documented in Documentation/devicetree/bindings/graph.txt. +- port@0: The input port in the ports node should be connected to a DPI output + port. +- port@1: The output port in the ports node should be connected to the input + port of a connector node that contains a ddc-i2c-bus property, or to the + input port of an attached bridge chip, such as a SlimPort transmitter. + +HDMI CEC +======== + +The HDMI CEC controller handles hotplug detection and CEC communication. + +Required properties: +- compatible: Should be "mediatek,<chip>-cec" +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clock + +HDMI DDC +======== + +The HDMI DDC i2c controller is used to interface with the HDMI DDC pins. +The Mediatek's I2C controller is used to interface with I2C devices. + +Required properties: +- compatible: Should be "mediatek,<chip>-hdmi-ddc" +- reg: Physical base address and length of the controller's registers +- clocks: device clock +- clock-names: Should be "ddc-i2c". + +HDMI PHY +======== + +The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel +output and drives the HDMI pads. + +Required properties: +- compatible: "mediatek,<chip>-hdmi-phy" +- reg: Physical base address and length of the module's registers +- clocks: PLL reference clock +- clock-names: must contain "pll_ref" +- clock-output-names: must be "hdmitx_dig_cts" on mt8173 +- #phy-cells: must be <0> +- #clock-cells: must be <0> + +Optional properties: +- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa +- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c + +Example: + +cec: cec@10013000 { + compatible = "mediatek,mt8173-cec"; + reg = <0 0x10013000 0 0xbc>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_CEC>; +}; + +hdmi_phy: hdmi-phy@10209100 { + compatible = "mediatek,mt8173-hdmi-phy"; + reg = <0 0x10209100 0 0x24>; + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>; + clock-names = "pll_ref"; + clock-output-names = "hdmitx_dig_cts"; + mediatek,ibias = <0xa>; + mediatek,ibias_up = <0x1c>; + #clock-cells = <0>; + #phy-cells = <0>; +}; + +hdmi_ddc0: i2c@11012000 { + compatible = "mediatek,mt8173-hdmi-ddc"; + reg = <0 0x11012000 0 0x1c>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_I2C5>; + clock-names = "ddc-i2c"; +}; + +hdmi0: hdmi@14025000 { + compatible = "mediatek,mt8173-hdmi"; + reg = <0 0x14025000 0 0x400>; + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>; + clocks = <&mmsys CLK_MM_HDMI_PIXEL>, + <&mmsys CLK_MM_HDMI_PLLCK>, + <&mmsys CLK_MM_HDMI_AUDIO>, + <&mmsys CLK_MM_HDMI_SPDIF>; + clock-names = "pixel", "pll", "bclk", "spdif"; + pinctrl-names = "default"; + pinctrl-0 = <&hdmi_pin>; + phys = <&hdmi_phy>; + phy-names = "hdmi"; + mediatek,syscon-hdmi = <&mmsys 0x900>; + assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>; + assigned-clock-parents = <&hdmi_phy>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi0_in: endpoint { + remote-endpoint = <&dpi0_out>; + }; + }; + + port@1 { + reg = <1>; + + hdmi0_out: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; + }; + }; +}; + +connector { + compatible = "hdmi-connector"; + type = "a"; + ddc-i2c-bus = <&hdmiddc0>; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi0_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt index f5948c48b9a2..6b1cab17f52d 100644 --- a/Documentation/devicetree/bindings/display/msm/dsi.txt +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -11,8 +11,7 @@ Required properties: be 0 or 1, since we have 2 DSI controllers at most for now. - interrupts: The interrupt signal from the DSI block. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. - clock-names: the following clocks are required: * "mdp_core_clk" * "iface_clk" @@ -23,16 +22,21 @@ Required properties: * "core_clk" For DSIv2, we need an additional clock: * "src_clk" +- assigned-clocks: Parents of "byte_clk" and "pixel_clk" for the given platform. +- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided + by a DSI PHY block. See [1] for details on clock bindings. - vdd-supply: phandle to vdd regulator device node - vddio-supply: phandle to vdd-io regulator device node - vdda-supply: phandle to vdda regulator device node -- qcom,dsi-phy: phandle to DSI PHY device node +- phys: phandle to DSI PHY device node +- phy-names: the name of the corresponding PHY device - syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) +- ports: Contains 2 DSI controller ports as child nodes. Each port contains + an endpoint subnode as defined in [2] and [3]. Optional properties: - panel@0: Node of panel connected to this DSI controller. - See files in Documentation/devicetree/bindings/display/panel/ for each supported - panel. + See files in [4] for each supported panel. - qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is driving a panel which needs 2 DSI links. - qcom,master-dsi: Boolean value indicating if the DSI controller is driving @@ -44,34 +48,38 @@ Optional properties: - pinctrl-names: the pin control state names; should contain "default" - pinctrl-0: the default pinctrl state (active) - pinctrl-n: the "sleep" pinctrl state -- port: DSI controller output port, containing one endpoint subnode. +- ports: contains DSI controller input and output ports as children, each + containing one endpoint subnode. DSI Endpoint properties: - - remote-endpoint: set to phandle of the connected panel's endpoint. - See Documentation/devicetree/bindings/graph.txt for device graph info. - - qcom,data-lane-map: this describes how the logical DSI lanes are mapped - to the physical lanes on the given platform. The value contained in - index n describes what logical data lane is mapped to the physical data - lane n (DATAn, where n lies between 0 and 3). + - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's + input endpoint. For port@1, set to the MDP interface output. See [2] for + device graph info. + + - data-lanes: this describes how the physical DSI data lanes are mapped + to the logical lanes on the given platform. The value contained in + index n describes what physical lane is mapped to the logical lane n + (DATAn, where n lies between 0 and 3). The clock lane position is fixed + and can't be changed. Hence, they aren't a part of the DT bindings. See + [3] for more info on the data-lanes property. For example: - qcom,data-lane-map = <3 0 1 2>; + data-lanes = <3 0 1 2>; - The above mapping describes that the logical data lane DATA3 is mapped to - the physical data lane DATA0, logical DATA0 to physical DATA1, logic DATA1 - to phys DATA2 and logic DATA2 to phys DATA3. + The above mapping describes that the logical data lane DATA0 is mapped to + the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 + to phys DATA1 and logic DATA3 to phys DATA2. There are only a limited number of physical to logical mappings possible: - - "0123": Logic 0->Phys 0; Logic 1->Phys 1; Logic 2->Phys 2; Logic 3->Phys 3; - "3012": Logic 3->Phys 0; Logic 0->Phys 1; Logic 1->Phys 2; Logic 2->Phys 3; - "2301": Logic 2->Phys 0; Logic 3->Phys 1; Logic 0->Phys 2; Logic 1->Phys 3; - "1230": Logic 1->Phys 0; Logic 2->Phys 1; Logic 3->Phys 2; Logic 0->Phys 3; - "0321": Logic 0->Phys 0; Logic 3->Phys 1; Logic 2->Phys 2; Logic 1->Phys 3; - "1032": Logic 1->Phys 0; Logic 0->Phys 1; Logic 3->Phys 2; Logic 2->Phys 3; - "2103": Logic 2->Phys 0; Logic 1->Phys 1; Logic 0->Phys 2; Logic 3->Phys 3; - "3210": Logic 3->Phys 0; Logic 2->Phys 1; Logic 1->Phys 2; Logic 0->Phys 3; + <0 1 2 3> + <1 2 3 0> + <2 3 0 1> + <3 0 1 2> + <0 3 2 1> + <1 0 3 2> + <2 1 0 3> + <3 2 1 0> DSI PHY: Required properties: @@ -86,11 +94,12 @@ Required properties: * "dsi_pll" * "dsi_phy" * "dsi_phy_regulator" +- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating + 2 clocks: A byte clock (index 0), and a pixel clock (index 1). - qcom,dsi-phy-index: The ID of DSI PHY hardware instance. This should be 0 or 1, since we have 2 DSI PHYs at most for now. - power-domains: Should be <&mmcc MDSS_GDSC>. -- clocks: device clocks - See Documentation/devicetree/bindings/clocks/clock-bindings.txt for details. +- clocks: Phandles to device clocks. See [1] for details on clock bindings. - clock-names: the following clocks are required: * "iface_clk" - vddio-supply: phandle to vdd-io regulator device node @@ -99,11 +108,16 @@ Optional properties: - qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY regulator is wanted. +[1] Documentation/devicetree/bindings/clocks/clock-bindings.txt +[2] Documentation/devicetree/bindings/graph.txt +[3] Documentation/devicetree/bindings/media/video-interfaces.txt +[4] Documentation/devicetree/bindings/display/panel/ + Example: - mdss_dsi0: qcom,mdss_dsi@fd922800 { + dsi0: dsi@fd922800 { compatible = "qcom,mdss-dsi-ctrl"; qcom,dsi-host-index = <0>; - interrupt-parent = <&mdss_mdp>; + interrupt-parent = <&mdp>; interrupts = <4 0>; reg-names = "dsi_ctrl"; reg = <0xfd922800 0x200>; @@ -124,19 +138,48 @@ Example: <&mmcc MDSS_AHB_CLK>, <&mmcc MDSS_MDP_CLK>, <&mmcc MDSS_PCLK0_CLK>; + + assigned-clocks = + <&mmcc BYTE0_CLK_SRC>, + <&mmcc PCLK0_CLK_SRC>; + assigned-clock-parents = + <&dsi_phy0 0>, + <&dsi_phy0 1>; + vdda-supply = <&pma8084_l2>; vdd-supply = <&pma8084_l22>; vddio-supply = <&pma8084_l12>; - qcom,dsi-phy = <&mdss_dsi_phy0>; + phys = <&dsi_phy0>; + phy-names ="dsi-phy"; qcom,dual-dsi-mode; qcom,master-dsi; qcom,sync-dual-dsi; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mdss_dsi_active>; - pinctrl-1 = <&mdss_dsi_suspend>; + pinctrl-0 = <&dsi_active>; + pinctrl-1 = <&dsi_suspend>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; panel: panel@0 { compatible = "sharp,lq101r1sx01"; @@ -152,16 +195,9 @@ Example: }; }; }; - - port { - dsi0_out: endpoint { - remote-endpoint = <&panel_in>; - lanes = <0 1 2 3>; - }; - }; }; - mdss_dsi_phy0: qcom,mdss_dsi_phy@fd922a00 { + dsi_phy0: dsi-phy@fd922a00 { compatible = "qcom,dsi-phy-28nm-hpm"; qcom,dsi-phy-index = <0>; reg-names = @@ -173,6 +209,7 @@ Example: <0xfd922d80 0x7b>; clock-names = "iface_clk"; clocks = <&mmcc MDSS_AHB_CLK>; + #clock-cells = <1>; vddio-supply = <&pma8084_l12>; qcom,dsi-phy-regulator-ldo-mode; diff --git a/Documentation/devicetree/bindings/display/msm/mdp.txt b/Documentation/devicetree/bindings/display/msm/mdp.txt deleted file mode 100644 index a214f6cd0363..000000000000 --- a/Documentation/devicetree/bindings/display/msm/mdp.txt +++ /dev/null @@ -1,59 +0,0 @@ -Qualcomm adreno/snapdragon display controller - -Required properties: -- compatible: - * "qcom,mdp4" - mdp4 - * "qcom,mdp5" - mdp5 -- reg: Physical base address and length of the controller's registers. -- interrupts: The interrupt signal from the display controller. -- connectors: array of phandles for output device(s) -- clocks: device clocks - See ../clocks/clock-bindings.txt for details. -- clock-names: the following clocks are required. - For MDP4: - * "core_clk" - * "iface_clk" - * "lut_clk" - * "src_clk" - * "hdmi_clk" - * "mdp_clk" - For MDP5: - * "bus_clk" - * "iface_clk" - * "core_clk_src" - * "core_clk" - * "lut_clk" (some MDP5 versions may not need this) - * "vsync_clk" - -Optional properties: -- gpus: phandle for gpu device -- clock-names: the following clocks are optional: - * "lut_clk" - -Example: - -/ { - ... - - mdp: qcom,mdp@5100000 { - compatible = "qcom,mdp4"; - reg = <0x05100000 0xf0000>; - interrupts = <GIC_SPI 75 0>; - connectors = <&hdmi>; - gpus = <&gpu>; - clock-names = - "core_clk", - "iface_clk", - "lut_clk", - "src_clk", - "hdmi_clk", - "mdp_clk"; - clocks = - <&mmcc MDP_SRC>, - <&mmcc MDP_AHB_CLK>, - <&mmcc MDP_LUT_CLK>, - <&mmcc TV_SRC>, - <&mmcc HDMI_TV_CLK>, - <&mmcc MDP_TV_CLK>; - }; -}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp4.txt b/Documentation/devicetree/bindings/display/msm/mdp4.txt new file mode 100644 index 000000000000..3c341a15ccdc --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp4.txt @@ -0,0 +1,112 @@ +Qualcomm adreno/snapdragon MDP4 display controller + +Description: + +This is the bindings documentation for the MDP4 display controller found in +SoCs like MSM8960, APQ8064 and MSM8660. + +Required properties: +- compatible: + * "qcom,mdp4" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "core_clk" + * "iface_clk" + * "bus_clk" + * "lut_clk" + * "hdmi_clk" + * "tv_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The output port mappings are: + Port 0 -> LCDC/LVDS + Port 1 -> DSI1 Cmd/Video + Port 2 -> DSI2 Cmd/Video + Port 3 -> DTV + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + hdmi: hdmi@4a00000 { + ... + ports { + ... + port@0 { + reg = <0>; + hdmi_in: endpoint { + remote-endpoint = <&mdp_dtv_out>; + }; + }; + ... + }; + ... + }; + + ... + + mdp: mdp@5100000 { + compatible = "qcom,mdp4"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "hdmi_clk", + "tv_clk"; + clocks = + <&mmcc MDP_CLK>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_AXI_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp_lvds_out: endpoint { + }; + }; + + port@1 { + reg = <1>; + mdp_dsi1_out: endpoint { + }; + }; + + port@2 { + reg = <2>; + mdp_dsi2_out: endpoint { + }; + }; + + port@3 { + reg = <3>; + mdp_dtv_out: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt new file mode 100644 index 000000000000..30c11ea83754 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp5.txt @@ -0,0 +1,160 @@ +Qualcomm adreno/snapdragon MDP5 display controller + +Description: + +This is the bindings documentation for the Mobile Display Subsytem(MDSS) that +encapsulates sub-blocks like MDP5, DSI, HDMI, eDP etc, and the MDP5 display +controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994 and MSM8996. + +MDSS: +Required properties: +- compatible: + * "qcom,mdss" - MDSS +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdss_phys" + * "vbif_phys" +- interrupts: The interrupt signal from MDSS. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "iface_clk" + * "bus_clk" + * "vsync_clk" +- #address-cells: number of address cells for the MDSS children. Should be 1. +- #size-cells: Should be 1. +- ranges: parent bus address space is the same as the child bus address space. + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +MDP5: +Required properties: +- compatible: + * "qcom,mdp5" - MDP5 +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdp_phys" +- interrupts: Interrupt line from MDP5 to MDSS interrupt controller. +- interrupt-parent: phandle to the MDSS block + through MDP block +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. +- * "bus_clk" +- * "iface_clk" +- * "core_clk" +- * "vsync_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The availability of output ports can vary across SoC revisions: + + For MSM8974 and APQ8084: + Port 0 -> MDP_INTF0 (eDP) + Port 1 -> MDP_INTF1 (DSI1) + Port 2 -> MDP_INTF2 (DSI2) + Port 3 -> MDP_INTF3 (HDMI) + + For MSM8916: + Port 0 -> MDP_INTF1 (DSI1) + + For MSM8994 and MSM8996: + Port 0 -> MDP_INTF1 (DSI1) + Port 1 -> MDP_INTF2 (DSI2) + Port 2 -> MDP_INTF3 (HDMI) + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + mdss: mdss@1a00000 { + compatible = "qcom,mdss"; + reg = <0x1a00000 0x1000>, + <0x1ac8000 0x3000>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "vsync_clk" + + interrupts = <0 72 0>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mdp: mdp@1a01000 { + compatible = "qcom,mdp5"; + reg = <0x1a01000 0x90000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0 0>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface_clk", + "bus_clk", + "core_clk", + "vsync_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp5_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: dsi@1a98000 { + ... + ports { + ... + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + ... + }; + ... + }; + + dsi_phy0: dsi-phy@1a98300 { + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt new file mode 100644 index 000000000000..3e10cd782491 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/innolux,at070tn92.txt @@ -0,0 +1,7 @@ +Innolux AT070TN92 7.0" WQVGA TFT LCD panel + +Required properties: +- compatible: should be "innolux,at070tn92" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt b/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt new file mode 100644 index 000000000000..b9877acad012 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp079qx1-sp0v.txt @@ -0,0 +1,7 @@ +LG LP079QX1-SP0V 7.9" (1536x2048 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp079qx1-sp0v" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt b/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt new file mode 100644 index 000000000000..42141516f078 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/lg,lp097qx1-spa1.txt @@ -0,0 +1,7 @@ +LG 9.7" (2048x1536 pixels) TFT LCD panel + +Required properties: +- compatible: should be "lg,lp097qx1-spa1" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt new file mode 100644 index 000000000000..74540a090669 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/olimex,lcd-olinuxino-43-ts.txt @@ -0,0 +1,7 @@ +Olimex 4.3" TFT LCD panel + +Required properties: +- compatible: should be "olimex,lcd-olinuxino-43-ts" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt new file mode 100644 index 000000000000..3d8a5e029242 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/ontat,yx700wv03.txt @@ -0,0 +1,7 @@ +On Tat Industrial Company 7" DPI TFT panel. + +Required properties: +- compatible: should be "ontat,yx700wv03" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt index 216c894d4f99..b52ac52757df 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-dpi.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-dpi.txt @@ -7,6 +7,8 @@ Required properties: Optional properties: - label: a symbolic name for the panel - enable-gpios: panel enable gpio +- reset-gpios: GPIO to control the RESET pin +- vcc-supply: phandle of regulator that will be used to enable power to the display Required nodes: - "panel-timing" containing video timings diff --git a/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt b/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt new file mode 100644 index 000000000000..dba298b43b24 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/samsung,lsn122dl01-c01.txt @@ -0,0 +1,7 @@ +Samsung 12.2" (2560x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "samsung,lsn122dl01-c01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt new file mode 100644 index 000000000000..4aff25b8dfe6 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq101k1ly04.txt @@ -0,0 +1,7 @@ +Sharp Display Corp. LQ101K1LY04 10.07" WXGA TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq101k1ly04" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt b/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt new file mode 100644 index 000000000000..bcb0e8a29f71 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/sharp,lq123p1jx31.txt @@ -0,0 +1,7 @@ +Sharp 12.3" (2400x1600 pixels) TFT LCD panel + +Required properties: +- compatible: should be "sharp,lq123p1jx31" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt b/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt new file mode 100644 index 000000000000..1e87fe6078af --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/starry,kr122ea0sra.txt @@ -0,0 +1,7 @@ +Starry 12.2" (1920x1200 pixels) TFT LCD panel + +Required properties: +- compatible: should be "starry,kr122ea0sra" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt new file mode 100644 index 000000000000..a2613b9675df --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f07a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 7" integrated projected capacitive touch display with, +800 x 480 (WVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f07a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt new file mode 100644 index 000000000000..b9d051196ba9 --- /dev/null +++ b/Documentation/devicetree/bindings/display/panel/tpk,f10a-0102.txt @@ -0,0 +1,8 @@ +TPK U.S.A. LLC Fusion 10.1" integrated projected capacitive touch display with, +1024 x 600 (WSVGA) LCD panel. + +Required properties: +- compatible: should be "tpk,f10a-0102" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt new file mode 100644 index 000000000000..01cced1c2a18 --- /dev/null +++ b/Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt @@ -0,0 +1,99 @@ +Rockchip RK3288 specific extensions to the Analogix Display Port +================================ + +Required properties: +- compatible: "rockchip,rk3288-dp", + "rockchip,rk3399-edp"; + +- reg: physical base address of the controller and length + +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. + +- clock-names: from common clock binding: + Required elements: "dp" "pclk" + +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + +- pinctrl-names: Names corresponding to the chip hotplug pinctrl states. +- pinctrl-0: pin-control mode. should be <&edp_hpd> + +- reset-names: Must include the name "dp" + +- rockchip,grf: this soc should set GRF regs, so need get grf here. + +- ports: there are 2 port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0: contained 2 endpoints, connecting to the output of vop. + Port 1: contained 1 endpoint, connecting to the input of panel. + +Optional property for different chips: +- clocks: from common clock binding: handle to grf_vio clock. + +- clock-names: from common clock binding: + Required elements: "grf" + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt +- phys (required) +- phy-names (required) +- hpd-gpios (optional) +- force-hpd (optional) +------------------------------------------------------------------------------- + +Example: + dp-controller: dp@ff970000 { + compatible = "rockchip,rk3288-dp"; + reg = <0xff970000 0x4000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_EDP>, <&cru PCLK_EDP_CTRL>; + clock-names = "dp", "pclk"; + phys = <&dp_phy>; + phy-names = "dp"; + + rockchip,grf = <&grf>; + resets = <&cru 111>; + reset-names = "dp"; + + pinctrl-names = "default"; + pinctrl-0 = <&edp_hpd>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + edp_in: port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + edp_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_edp>; + }; + edp_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_edp>; + }; + }; + + edp_out: port@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + edp_out_panel: endpoint { + reg = <0>; + remote-endpoint = <&panel_in_edp> + }; + }; + }; + }; + + pinctrl { + edp { + edp_hpd: edp-hpd { + rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/snps,arcpgu.txt b/Documentation/devicetree/bindings/display/snps,arcpgu.txt new file mode 100644 index 000000000000..c5c7dfd37df2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/snps,arcpgu.txt @@ -0,0 +1,35 @@ +ARC PGU + +This is a display controller found on several development boards produced +by Synopsys. The ARC PGU is an RGB streamer that reads the data from a +framebuffer and sends it to a single digital encoder (usually HDMI). + +Required properties: + - compatible: "snps,arcpgu" + - reg: Physical base address and length of the controller's registers. + - clocks: A list of phandle + clock-specifier pairs, one for each + entry in 'clock-names'. + - clock-names: A list of clock names. For ARC PGU it should contain: + - "pxlclk" for the clock feeding the output PLL of the controller. + +Required sub-nodes: + - port: The PGU connection to an encoder chip. + +Example: + +/ { + ... + + pgu@XXXXXXXX { + compatible = "snps,arcpgu"; + reg = <0xXXXXXXXX 0x400>; + clocks = <&clock_node>; + clock-names = "pxlclk"; + + port { + pgu_output: endpoint { + remote-endpoint = <&hdmi_enc_input>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt new file mode 100644 index 000000000000..df8f4aeefe4c --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt @@ -0,0 +1,258 @@ +Allwinner A10 Display Pipeline +============================== + +The Allwinner A10 Display pipeline is composed of several components +that are going to be documented below: + +TV Encoder +---------- + +The TV Encoder supports the composite and VGA output. It is one end of +the pipeline. + +Required properties: + - compatible: value should be "allwinner,sun4i-a10-tv-encoder". + - reg: base address and size of memory-mapped region + - clocks: the clocks driving the TV encoder + - resets: phandle to the reset controller driving the encoder + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint. + +TCON +---- + +The TCON acts as a timing controller for RGB, LVDS and TV interfaces. + +Required properties: + - compatible: value should be "allwinner,sun5i-a13-tcon". + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the TCON. Three are needed: + - 'ahb': the interface clocks + - 'tcon-ch0': The clock driving the TCON channel 0 + - 'tcon-ch1': The clock driving the TCON channel 1 + - resets: phandles to the reset controllers driving the encoder + - "lcd": the reset line for the TCON channel 0 + + - clock-names: the clock names mentioned above + - reset-names: the reset names mentioned above + - clock-output-names: Name of the pixel clock created + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint, the second one the output + + The output should have two endpoints. The first is the block + connected to the TCON channel 0 (usually a panel or a bridge), the + second the block connected to the TCON channel 1 (usually the TV + encoder) + + +Display Engine Backend +---------------------- + +The display engine backend exposes layers and sprites to the +system. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-backend + - reg: base address and size of the memory-mapped region. + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the output + +Display Engine Frontend +----------------------- + +The display engine frontend does formats conversion, scaling, +deinterlacing and color space conversion. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-frontend + - reg: base address and size of the memory-mapped region. + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the frontend and backend + * ahb: the backend interface clock + * mod: the backend module clock + * ram: the backend DRAM clock + - clock-names: the clock names mentioned above + - resets: phandles to the reset controllers driving the backend + +- ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoints, the second one the outputs + + +Display Engine Pipeline +----------------------- + +The display engine pipeline (and its entry point, since it can be +either directly the backend or the frontend) is represented as an +extra node. + +Required properties: + - compatible: value must be one of: + * allwinner,sun5i-a13-display-engine + + - allwinner,pipelines: list of phandle to the display engine + frontends available. + +Example: + +panel: panel { + compatible = "olimex,lcd-olinuxino-43-ts"; + #address-cells = <1>; + #size-cells = <0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + panel_input: endpoint { + remote-endpoint = <&tcon0_out_panel>; + }; + }; +}; + +tve0: tv-encoder@01c0a000 { + compatible = "allwinner,sun4i-a10-tv-encoder"; + reg = <0x01c0a000 0x1000>; + clocks = <&ahb_gates 34>; + resets = <&tcon_ch0_clk 0>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + tve0_in_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_out_tve0>; + }; + }; +}; + +tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun5i-a13-tcon"; + reg = <0x01c0c000 0x1000>; + interrupts = <44>; + resets = <&tcon_ch0_clk 1>; + reset-names = "lcd"; + clocks = <&ahb_gates 36>, + <&tcon_ch0_clk>, + <&tcon_ch1_clk>; + clock-names = "ahb", + "tcon-ch0", + "tcon-ch1"; + clock-output-names = "tcon-pixel-clock"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_be0: endpoint@0 { + reg = <0>; + remote-endpoint = <&be0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tcon0_out_panel: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + + tcon0_out_tve0: endpoint@1 { + reg = <1>; + remote-endpoint = <&tve0_in_tcon0>; + }; + }; + }; +}; + +fe0: display-frontend@1e00000 { + compatible = "allwinner,sun5i-a13-display-frontend"; + reg = <0x01e00000 0x20000>; + interrupts = <47>; + clocks = <&ahb_gates 46>, <&de_fe_clk>, + <&dram_gates 25>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_fe_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + fe0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + fe0_out_be0: endpoint { + remote-endpoint = <&be0_in_fe0>; + }; + }; + }; +}; + +be0: display-backend@1e60000 { + compatible = "allwinner,sun5i-a13-display-backend"; + reg = <0x01e60000 0x10000>; + clocks = <&ahb_gates 44>, <&de_be_clk>, + <&dram_gates 26>; + clock-names = "ahb", "mod", + "ram"; + resets = <&de_be_clk>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + be0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + be0_in_fe0: endpoint@0 { + reg = <0>; + remote-endpoint = <&fe0_out_be0>; + }; + }; + + be0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + be0_out_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_in_be0>; + }; + }; + }; +}; + +display-engine { + compatible = "allwinner,sun5i-a13-display-engine"; + allwinner,pipelines = <&fe0>; +}; diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt index a3bd8c050c4e..0fad7ed2ea19 100644 --- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt @@ -208,6 +208,7 @@ of the following host1x client modules: See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: - sor: clock input for the SOR hardware + - source: source clock for the SOR clock - parent: input for the pixel clock - dp: reference clock for the SOR clock - safe: safe reference for the SOR clock during power up @@ -226,9 +227,9 @@ of the following host1x client modules: - nvidia,dpaux: phandle to a DispayPort AUX interface - dpaux: DisplayPort AUX interface - - compatible: For Tegra124, must contain "nvidia,tegra124-dpaux". Otherwise, - must contain '"nvidia,<chip>-dpaux", "nvidia,tegra124-dpaux"', where - <chip> is tegra132. + - compatible : Should contain one of the following: + - "nvidia,tegra124-dpaux": for Tegra124 and Tegra132 + - "nvidia,tegra210-dpaux": for Tegra210 - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. - clocks: Must contain an entry for each entry in clock-names. @@ -241,6 +242,12 @@ of the following host1x client modules: - reset-names: Must include the following entries: - dpaux - vdd-supply: phandle of a supply that powers the DisplayPort link + - i2c-bus: Subnode where I2C slave devices are listed. This subnode + must be always present. If there are no I2C slave devices, an empty + node should be added. See ../../i2c/i2c.txt for more information. + + See ../pinctrl/nvidia,tegra124-dpaux-padctl.txt for information + regarding the DPAUX pad controller bindings. Example: |