summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/spi/Kconfig3
-rw-r--r--drivers/spi/spi-armada-3700.c14
-rw-r--r--drivers/spi/spi-ath79.c23
-rw-r--r--drivers/spi/spi-bcm-qspi.c194
-rw-r--r--drivers/spi/spi-bcm53xx.c18
5 files changed, 158 insertions, 94 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 2922a9908302..0f8afeed648e 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -162,7 +162,8 @@ config SPI_BCM63XX_HSSPI
config SPI_BCM_QSPI
tristate "Broadcom BSPI and MSPI controller support"
- depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST
+ depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
+ BMIPS_GENERIC || COMPILE_TEST
default ARCH_BCM_IPROC
help
Enables support for the Broadcom SPI flash and MSPI controller.
diff --git a/drivers/spi/spi-armada-3700.c b/drivers/spi/spi-armada-3700.c
index 0314c6b9e044..6c7d7a460689 100644
--- a/drivers/spi/spi-armada-3700.c
+++ b/drivers/spi/spi-armada-3700.c
@@ -170,12 +170,12 @@ static int a3700_spi_pin_mode_set(struct a3700_spi *a3700_spi,
val &= ~(A3700_SPI_DATA_PIN0 | A3700_SPI_DATA_PIN1);
switch (pin_mode) {
- case 1:
+ case SPI_NBITS_SINGLE:
break;
- case 2:
+ case SPI_NBITS_DUAL:
val |= A3700_SPI_DATA_PIN0;
break;
- case 4:
+ case SPI_NBITS_QUAD:
val |= A3700_SPI_DATA_PIN1;
break;
default:
@@ -340,8 +340,7 @@ static irqreturn_t a3700_spi_interrupt(int irq, void *dev_id)
spireg_write(a3700_spi, A3700_SPI_INT_STAT_REG, cause);
/* Wake up the transfer */
- if (a3700_spi->wait_mask & cause)
- complete(&a3700_spi->done);
+ complete(&a3700_spi->done);
return IRQ_HANDLED;
}
@@ -421,7 +420,7 @@ static void a3700_spi_fifo_thres_set(struct a3700_spi *a3700_spi,
}
static void a3700_spi_transfer_setup(struct spi_device *spi,
- struct spi_transfer *xfer)
+ struct spi_transfer *xfer)
{
struct a3700_spi *a3700_spi;
unsigned int byte_len;
@@ -562,6 +561,7 @@ static int a3700_spi_fifo_read(struct a3700_spi *a3700_spi)
val = spireg_read(a3700_spi, A3700_SPI_DATA_IN_REG);
if (a3700_spi->buf_len >= 4) {
u32 data = le32_to_cpu(val);
+
memcpy(a3700_spi->rx_buf, &data, 4);
a3700_spi->buf_len -= 4;
@@ -901,7 +901,6 @@ static int a3700_spi_remove(struct platform_device *pdev)
struct a3700_spi *spi = spi_master_get_devdata(master);
clk_unprepare(spi->clk);
- spi_master_put(master);
return 0;
}
@@ -909,7 +908,6 @@ static int a3700_spi_remove(struct platform_device *pdev)
static struct platform_driver a3700_spi_driver = {
.driver = {
.name = DRIVER_NAME,
- .owner = THIS_MODULE,
.of_match_table = of_match_ptr(a3700_spi_dt_ids),
},
.probe = a3700_spi_probe,
diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c
index f369174fbd88..b89cee11f418 100644
--- a/drivers/spi/spi-ath79.c
+++ b/drivers/spi/spi-ath79.c
@@ -78,14 +78,16 @@ static void ath79_spi_chipselect(struct spi_device *spi, int is_active)
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
- if (spi->chip_select) {
+ if (gpio_is_valid(spi->cs_gpio)) {
/* SPI is normally active-low */
- gpio_set_value(spi->cs_gpio, cs_high);
+ gpio_set_value_cansleep(spi->cs_gpio, cs_high);
} else {
+ u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
+
if (cs_high)
- sp->ioc_base |= AR71XX_SPI_IOC_CS0;
+ sp->ioc_base |= cs_bit;
else
- sp->ioc_base &= ~AR71XX_SPI_IOC_CS0;
+ sp->ioc_base &= ~cs_bit;
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
@@ -118,11 +120,8 @@ static int ath79_spi_setup_cs(struct spi_device *spi)
struct ath79_spi *sp = ath79_spidev_to_sp(spi);
int status;
- if (spi->chip_select && !gpio_is_valid(spi->cs_gpio))
- return -EINVAL;
-
status = 0;
- if (spi->chip_select) {
+ if (gpio_is_valid(spi->cs_gpio)) {
unsigned long flags;
flags = GPIOF_DIR_OUT;
@@ -134,10 +133,12 @@ static int ath79_spi_setup_cs(struct spi_device *spi)
status = gpio_request_one(spi->cs_gpio, flags,
dev_name(&spi->dev));
} else {
+ u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select);
+
if (spi->mode & SPI_CS_HIGH)
- sp->ioc_base &= ~AR71XX_SPI_IOC_CS0;
+ sp->ioc_base &= ~cs_bit;
else
- sp->ioc_base |= AR71XX_SPI_IOC_CS0;
+ sp->ioc_base |= cs_bit;
ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base);
}
@@ -147,7 +148,7 @@ static int ath79_spi_setup_cs(struct spi_device *spi)
static void ath79_spi_cleanup_cs(struct spi_device *spi)
{
- if (spi->chip_select) {
+ if (gpio_is_valid(spi->cs_gpio)) {
gpio_free(spi->cs_gpio);
}
}
diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c
index 14f9dea3173f..958fb4ee972d 100644
--- a/drivers/spi/spi-bcm-qspi.c
+++ b/drivers/spi/spi-bcm-qspi.c
@@ -89,7 +89,7 @@
#define BSPI_BPP_MODE_SELECT_MASK BIT(8)
#define BSPI_BPP_ADDR_SELECT_MASK BIT(16)
-#define BSPI_READ_LENGTH 256
+#define BSPI_READ_LENGTH 512
/* MSPI register offsets */
#define MSPI_SPCR0_LSB 0x000
@@ -192,9 +192,11 @@ struct bcm_qspi_dev_id {
void *dev;
};
+
struct qspi_trans {
struct spi_transfer *trans;
int byte;
+ bool mspi_last_trans;
};
struct bcm_qspi {
@@ -616,6 +618,16 @@ static int bcm_qspi_setup(struct spi_device *spi)
return 0;
}
+static bool bcm_qspi_mspi_transfer_is_last(struct bcm_qspi *qspi,
+ struct qspi_trans *qt)
+{
+ if (qt->mspi_last_trans &&
+ spi_transfer_is_last(qspi->master, qt->trans))
+ return true;
+ else
+ return false;
+}
+
static int update_qspi_trans_byte_count(struct bcm_qspi *qspi,
struct qspi_trans *qt, int flags)
{
@@ -629,7 +641,6 @@ static int update_qspi_trans_byte_count(struct bcm_qspi *qspi,
if (qt->byte >= qt->trans->len) {
/* we're at the end of the spi_transfer */
-
/* in TX mode, need to pause for a delay or CS change */
if (qt->trans->delay_usecs &&
(flags & TRANS_STATUS_BREAK_DELAY))
@@ -641,7 +652,7 @@ static int update_qspi_trans_byte_count(struct bcm_qspi *qspi,
goto done;
dev_dbg(&qspi->pdev->dev, "advance msg exit\n");
- if (spi_transfer_is_last(qspi->master, qt->trans))
+ if (bcm_qspi_mspi_transfer_is_last(qspi, qt))
ret = TRANS_STATUS_BREAK_EOM;
else
ret = TRANS_STATUS_BREAK_NO_BYTES;
@@ -813,7 +824,7 @@ static int bcm_qspi_bspi_flash_read(struct spi_device *spi,
struct spi_flash_read_message *msg)
{
struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
- u32 addr = 0, len, len_words;
+ u32 addr = 0, len, rdlen, len_words;
int ret = 0;
unsigned long timeo = msecs_to_jiffies(100);
struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc;
@@ -826,7 +837,7 @@ static int bcm_qspi_bspi_flash_read(struct spi_device *spi,
bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0);
/*
- * when using flex mode mode we need to send
+ * when using flex mode we need to send
* the upper address byte to bspi
*/
if (bcm_qspi_bspi_ver_three(qspi) == false) {
@@ -840,48 +851,127 @@ static int bcm_qspi_bspi_flash_read(struct spi_device *spi,
else
addr = msg->from & 0x00ffffff;
- /* set BSPI RAF buffer max read length */
- len = msg->len;
- if (len > BSPI_READ_LENGTH)
- len = BSPI_READ_LENGTH;
-
if (bcm_qspi_bspi_ver_three(qspi) == true)
addr = (addr + 0xc00000) & 0xffffff;
- reinit_completion(&qspi->bspi_done);
- bcm_qspi_enable_bspi(qspi);
- len_words = (len + 3) >> 2;
- qspi->bspi_rf_msg = msg;
- qspi->bspi_rf_msg_status = 0;
+ /*
+ * read into the entire buffer by breaking the reads
+ * into RAF buffer read lengths
+ */
+ len = msg->len;
qspi->bspi_rf_msg_idx = 0;
- qspi->bspi_rf_msg_len = len;
- dev_dbg(&qspi->pdev->dev, "bspi xfr addr 0x%x len 0x%x", addr, len);
- bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr);
- bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words);
- bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0);
+ do {
+ if (len > BSPI_READ_LENGTH)
+ rdlen = BSPI_READ_LENGTH;
+ else
+ rdlen = len;
+
+ reinit_completion(&qspi->bspi_done);
+ bcm_qspi_enable_bspi(qspi);
+ len_words = (rdlen + 3) >> 2;
+ qspi->bspi_rf_msg = msg;
+ qspi->bspi_rf_msg_status = 0;
+ qspi->bspi_rf_msg_len = rdlen;
+ dev_dbg(&qspi->pdev->dev,
+ "bspi xfr addr 0x%x len 0x%x", addr, rdlen);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0);
+ if (qspi->soc_intc) {
+ /*
+ * clear soc MSPI and BSPI interrupts and enable
+ * BSPI interrupts.
+ */
+ soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_BSPI_DONE);
+ soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE, true);
+ }
- if (qspi->soc_intc) {
- /*
- * clear soc MSPI and BSPI interrupts and enable
- * BSPI interrupts.
- */
- soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_BSPI_DONE);
- soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE, true);
+ /* Must flush previous writes before starting BSPI operation */
+ mb();
+ bcm_qspi_bspi_lr_start(qspi);
+ if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) {
+ dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n");
+ ret = -ETIMEDOUT;
+ break;
+ }
+
+ /* set msg return length */
+ msg->retlen += rdlen;
+ addr += rdlen;
+ len -= rdlen;
+ } while (len);
+
+ return ret;
+}
+
+static int bcm_qspi_transfer_one(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *trans)
+{
+ struct bcm_qspi *qspi = spi_master_get_devdata(master);
+ int slots;
+ unsigned long timeo = msecs_to_jiffies(100);
+
+ bcm_qspi_chip_select(qspi, spi->chip_select);
+ qspi->trans_pos.trans = trans;
+ qspi->trans_pos.byte = 0;
+
+ while (qspi->trans_pos.byte < trans->len) {
+ reinit_completion(&qspi->mspi_done);
+
+ slots = write_to_hw(qspi, spi);
+ if (!wait_for_completion_timeout(&qspi->mspi_done, timeo)) {
+ dev_err(&qspi->pdev->dev, "timeout waiting for MSPI\n");
+ return -ETIMEDOUT;
+ }
+
+ read_from_hw(qspi, slots);
}
- /* Must flush previous writes before starting BSPI operation */
- mb();
+ return 0;
+}
- bcm_qspi_bspi_lr_start(qspi);
- if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) {
- dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n");
- ret = -ETIMEDOUT;
- } else {
- /* set the return length for the caller */
- msg->retlen = len;
+static int bcm_qspi_mspi_flash_read(struct spi_device *spi,
+ struct spi_flash_read_message *msg)
+{
+ struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
+ struct spi_transfer t[2];
+ u8 cmd[6];
+ int ret;
+
+ memset(cmd, 0, sizeof(cmd));
+ memset(t, 0, sizeof(t));
+
+ /* tx */
+ /* opcode is in cmd[0] */
+ cmd[0] = msg->read_opcode;
+ cmd[1] = msg->from >> (msg->addr_width * 8 - 8);
+ cmd[2] = msg->from >> (msg->addr_width * 8 - 16);
+ cmd[3] = msg->from >> (msg->addr_width * 8 - 24);
+ cmd[4] = msg->from >> (msg->addr_width * 8 - 32);
+ t[0].tx_buf = cmd;
+ t[0].len = msg->addr_width + msg->dummy_bytes + 1;
+ t[0].bits_per_word = spi->bits_per_word;
+ t[0].tx_nbits = msg->opcode_nbits;
+ /* lets mspi know that this is not last transfer */
+ qspi->trans_pos.mspi_last_trans = false;
+ ret = bcm_qspi_transfer_one(spi->master, spi, &t[0]);
+
+ /* rx */
+ qspi->trans_pos.mspi_last_trans = true;
+ if (!ret) {
+ /* rx */
+ t[1].rx_buf = msg->buf;
+ t[1].len = msg->len;
+ t[1].rx_nbits = msg->data_nbits;
+ t[1].bits_per_word = spi->bits_per_word;
+ ret = bcm_qspi_transfer_one(spi->master, spi, &t[1]);
}
+ if (!ret)
+ msg->retlen = msg->len;
+
return ret;
}
@@ -918,8 +1008,7 @@ static int bcm_qspi_flash_read(struct spi_device *spi,
mspi_read = true;
if (mspi_read)
- /* this will make the m25p80 read to fallback to mspi read */
- return -EAGAIN;
+ return bcm_qspi_mspi_flash_read(spi, msg);
io_width = msg->data_nbits ? msg->data_nbits : SPI_NBITS_SINGLE;
addrlen = msg->addr_width;
@@ -931,33 +1020,6 @@ static int bcm_qspi_flash_read(struct spi_device *spi,
return ret;
}
-static int bcm_qspi_transfer_one(struct spi_master *master,
- struct spi_device *spi,
- struct spi_transfer *trans)
-{
- struct bcm_qspi *qspi = spi_master_get_devdata(master);
- int slots;
- unsigned long timeo = msecs_to_jiffies(100);
-
- bcm_qspi_chip_select(qspi, spi->chip_select);
- qspi->trans_pos.trans = trans;
- qspi->trans_pos.byte = 0;
-
- while (qspi->trans_pos.byte < trans->len) {
- reinit_completion(&qspi->mspi_done);
-
- slots = write_to_hw(qspi, spi);
- if (!wait_for_completion_timeout(&qspi->mspi_done, timeo)) {
- dev_err(&qspi->pdev->dev, "timeout waiting for MSPI\n");
- return -ETIMEDOUT;
- }
-
- read_from_hw(qspi, slots);
- }
-
- return 0;
-}
-
static void bcm_qspi_cleanup(struct spi_device *spi)
{
struct bcm_qspi_parms *xp = spi_get_ctldata(spi);
@@ -1187,6 +1249,7 @@ int bcm_qspi_probe(struct platform_device *pdev,
qspi->pdev = pdev;
qspi->trans_pos.trans = NULL;
qspi->trans_pos.byte = 0;
+ qspi->trans_pos.mspi_last_trans = true;
qspi->master = master;
master->bus_num = -1;
@@ -1345,7 +1408,6 @@ int bcm_qspi_remove(struct platform_device *pdev)
{
struct bcm_qspi *qspi = platform_get_drvdata(pdev);
- platform_set_drvdata(pdev, NULL);
bcm_qspi_hw_uninit(qspi);
clk_disable_unprepare(qspi->clk);
kfree(qspi->dev_ids);
diff --git a/drivers/spi/spi-bcm53xx.c b/drivers/spi/spi-bcm53xx.c
index afb51699dbb5..6e409eabe1c9 100644
--- a/drivers/spi/spi-bcm53xx.c
+++ b/drivers/spi/spi-bcm53xx.c
@@ -1,3 +1,11 @@
+/*
+ * Copyright (C) 2014-2016 Rafał Miłecki <rafal@milecki.pl>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/kernel.h>
@@ -275,10 +283,6 @@ static int bcm53xxspi_flash_read(struct spi_device *spi,
* BCMA
**************************************************/
-static struct spi_board_info bcm53xx_info = {
- .modalias = "bcm53xxspiflash",
-};
-
static const struct bcma_device_id bcm53xxspi_bcma_tbl[] = {
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_QSPI, BCMA_ANY_REV, BCMA_ANY_CLASS),
{},
@@ -311,6 +315,7 @@ static int bcm53xxspi_bcma_probe(struct bcma_device *core)
b53spi->bspi = true;
bcm53xxspi_disable_bspi(b53spi);
+ master->dev.of_node = dev->of_node;
master->transfer_one = bcm53xxspi_transfer_one;
if (b53spi->mmio_base)
master->spi_flash_read = bcm53xxspi_flash_read;
@@ -324,9 +329,6 @@ static int bcm53xxspi_bcma_probe(struct bcma_device *core)
return err;
}
- /* Broadcom SoCs (at least with the CC rev 42) use SPI for flash only */
- spi_new_device(master, &bcm53xx_info);
-
return 0;
}
@@ -361,4 +363,4 @@ module_exit(bcm53xxspi_module_exit);
MODULE_DESCRIPTION("Broadcom BCM53xx SPI Controller driver");
MODULE_AUTHOR("Rafał Miłecki <zajec5@gmail.com>");
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
View Lorry Controller Status