summaryrefslogtreecommitdiff
path: root/net/mac80211
Commit message (Collapse)AuthorAgeFilesLines
...
| * | | mac80211: max_tp_rate2 management of minstrel_htLorenzo Bianconi2011-09-301-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I noticed a possible issue in the max_tp_rate2 management of minstrel_ht. In particular, if we look up just among max_tp_rate2 of each group it will be possible that the selected rate will not be the mcs with second maximum throughput. I wrote this simple patch. Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | | Merge branch 'master' of ↵John W. Linville2011-09-3014-123/+191
|\ \ \ \ | |/ / / | | | | | | | | | | | | | | | | | | | | | | | | git://git.infradead.org/users/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/iwlwifi/iwl-pci.c drivers/net/wireless/wl12xx/main.c
| * | | mac80211: save tx params per sdataEliad Peller2011-09-276-15/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | save and configure tx param per sdata, rather than per hardware. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | cfg80211/mac80211: add netdev param to set_txq_params()Eliad Peller2011-09-271-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | tx params are currently configured per hw, although they should be configured per interface. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | mac80211: Send the management frame at requested rateRajkumar Manoharan2011-09-277-7/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Whenever the scan request or tx_mgmt is requesting not to use CCK rate for managemet frames through NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should select appropriate least non-CCK rate. This could help to send P2P probes and P2P action frames at non 11b rates without diabling 11b rates globally. Cc: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | nl80211/cfg80211: Add support to disable CCK rate for management frameRajkumar Manoharan2011-09-271-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a new nl80211 attribute to specify whether to send the management frames in CCK rate or not. As of now the wpa_supplicant is disabling CCK rate at P2P init itself. So this patch helps to send P2P probe request/probe response/action frames being sent at non CCK rate in 2GHz without disabling 11b rates. This attribute is used with NL80211_CMD_TRIGGER_SCAN and NL80211_CMD_FRAME commands to disable CCK rate for management frame transmission. Cc: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | mac80211: add ieee80211_vif param to tsf functionsEliad Peller2011-09-275-74/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TSF can be kept per vif. Add ieee80211_vif param to set/get/reset_tsf, and move the debugfs entries to the per-vif directory. Update all the drivers that implement these callbacks. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | mac80211: notify peer when shutting down peer linkThomas Pedersen2011-09-211-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Send a Mesh Peering Close frame when we deactivate a mesh peer link. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | mac80211: fix AP/VLAN PS buffer raceJohannes Berg2011-09-211-6/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an AP interface is removed without the AP/VLAN interfaces having been removed before already, the AP-VLAN interface might still have sleeping stations and buffer multicast frames which will happen on the AP interface. Thus, we need to remove AP/VLAN interfaces before purging buffered broadcast frames. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | mac80211: fix indentationAlexander Simon2011-09-201-1/+1
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | Merge branch 'master' of git://git.infradead.org/users/linville/wirelessJohn W. Linville2011-09-202-2/+2
| |\ \ \ | | |/ / | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/wireless/iwlwifi/iwl-pci.c drivers/net/wireless/iwlwifi/iwl-trans-pcie-tx.c drivers/net/wireless/rt2x00/rt2800usb.c drivers/net/wireless/wl12xx/main.c
| * | | mac80211: Fix regression on queue stop during 2040 bss changeRajkumar Manoharan2011-09-191-19/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit "mac80211: stop tx before doing hw config and rate update" stops the tx queue and call drv_flush so frequently whenever a beacon got received with 11n htcap. This leads to massive "Failed to stop TX DMA" logspam on embedded hw. So the queue stop and flush should be called if and only if there is a change in the channel type. Reported-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | | Merge branch 'master' of github.com:davem330/netDavid S. Miller2011-09-222-2/+2
|\ \ \ \ | | |/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: MAINTAINERS drivers/net/Kconfig drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c drivers/net/ethernet/broadcom/tg3.c drivers/net/wireless/iwlwifi/iwl-pci.c drivers/net/wireless/iwlwifi/iwl-trans-tx-pcie.c drivers/net/wireless/rt2x00/rt2800usb.c drivers/net/wireless/wl12xx/main.c
| * | | mac80211: fix missing sta_lock in __sta_info_destroyJohannes Berg2011-09-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since my commit 34e895075e21be3e21e71d6317440d1ee7969ad0 ("mac80211: allow station add/remove to sleep") there is a race in mac80211 when it clears the TIM bit because a sleeping station disconnected, the spinlock isn't held around the relevant code any more. Use the right API to acquire the spinlock correctly. Cc: stable@kernel.org [2.6.34+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | | mac80211: fix suspend/resume races with unregister hwStanislaw Gruszka2011-08-221-1/+1
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Do not call ->suspend, ->resume methods after we unregister wiphy. Also delete sta_clanup timer after we finish wiphy unregister to avoid this: WARNING: at lib/debugobjects.c:262 debug_print_object+0x85/0xa0() Hardware name: 6369CTO ODEBUG: free active (active state 0) object type: timer_list hint: sta_info_cleanup+0x0/0x180 [mac80211] Modules linked in: aes_i586 aes_generic fuse bridge stp llc autofs4 sunrpc cpufreq_ondemand acpi_cpufreq mperf ext2 dm_mod uinput thinkpad_acpi hwmon sg arc4 rt2800usb rt2800lib crc_ccitt rt2x00usb rt2x00lib mac80211 cfg80211 i2c_i801 iTCO_wdt iTCO_vendor_support e1000e ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom yenta_socket ahci libahci pata_acpi ata_generic ata_piix i915 drm_kms_helper drm i2c_algo_bit video [last unloaded: microcode] Pid: 5663, comm: pm-hibernate Not tainted 3.1.0-rc1-wl+ #19 Call Trace: [<c0454cfd>] warn_slowpath_common+0x6d/0xa0 [<c05e05e5>] ? debug_print_object+0x85/0xa0 [<c05e05e5>] ? debug_print_object+0x85/0xa0 [<c0454dae>] warn_slowpath_fmt+0x2e/0x30 [<c05e05e5>] debug_print_object+0x85/0xa0 [<f8a808e0>] ? sta_info_alloc+0x1a0/0x1a0 [mac80211] [<c05e0bd2>] debug_check_no_obj_freed+0xe2/0x180 [<c051175b>] kfree+0x8b/0x150 [<f8a126ae>] cfg80211_dev_free+0x7e/0x90 [cfg80211] [<f8a13afd>] wiphy_dev_release+0xd/0x10 [cfg80211] [<c068d959>] device_release+0x19/0x80 [<c05d06ba>] kobject_release+0x7a/0x1c0 [<c07646a8>] ? rtnl_unlock+0x8/0x10 [<f8a13adb>] ? wiphy_resume+0x6b/0x80 [cfg80211] [<c05d0640>] ? kobject_del+0x30/0x30 [<c05d1a6d>] kref_put+0x2d/0x60 [<c05d056d>] kobject_put+0x1d/0x50 [<c08015f4>] ? mutex_lock+0x14/0x40 [<c068d60f>] put_device+0xf/0x20 [<c069716a>] dpm_resume+0xca/0x160 [<c04912bd>] hibernation_snapshot+0xcd/0x260 [<c04903df>] ? freeze_processes+0x3f/0x90 [<c049151b>] hibernate+0xcb/0x1e0 [<c048fdc0>] ? pm_async_store+0x40/0x40 [<c048fe60>] state_store+0xa0/0xb0 [<c048fdc0>] ? pm_async_store+0x40/0x40 [<c05d0200>] kobj_attr_store+0x20/0x30 [<c0575ea4>] sysfs_write_file+0x94/0xf0 [<c051e26a>] vfs_write+0x9a/0x160 [<c0575e10>] ? sysfs_open_file+0x200/0x200 [<c051e3fd>] sys_write+0x3d/0x70 [<c080959f>] sysenter_do_call+0x12/0x28 Cc: stable@kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | Merge branch 'master' of ssh://infradead/~/public_git/wireless-next into ↵John W. Linville2011-09-1925-227/+329
|\ \ \ | | |/ | |/| | | | for-davem
| * | mac80211: fix endian issues and comments for BAR failure handlingFelix Fietkau2011-09-161-6/+8
| | | | | | | | | | | | | | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Update device channel in case of HW channel switch supportedShahar Levi2011-09-141-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The hw.conf.channel value is not updated properly for drivers that support HW channel switch. Since the switch is done entirely by the driver and we don't call ieee80211_hw_config(), this value remains untouched. This patch fixes that by setting the new channel directly in ieee80211_chswitch_work(). Signed-off-by: Shahar Levi <shahar_levi@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Mark all mesh stations as QoS capableJavier Cardona2011-09-141-1/+1
| | | | | | | | | | | | | | | Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Mesh data frames must have the QoS headerJavier Cardona2011-09-147-14/+15
| | | | | | | | | | | | | | | | | | | | | | | | Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the presence of the mesh control header in their QoS header. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Start implementing QoS support for mesh interfacesJavier Cardona2011-09-144-10/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In order to support QoS in mesh, we need to assign queue mapping only after the next hop has been resolved, both for forwarded and locally originated frames. Also, now that this is fixed, remove the XXX comment in ieee80211_select_queue(). Also, V-Shy Ho reported that the queue mapping was not being applied to the forwarded frame (fwd_skb instead of skb). Fixed that as well. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: further optimise buffer expiry timerJohannes Berg2011-09-141-7/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Juuso optimised the timer to not run all the time in commit 3393a608c4979a94d1887efc05b7. However, after that it will still run once more even if all frames just expired. Fixing that also makes the function return value a little clearer in the process. Also, while at it, change the return value to bool (instead of int). Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: add ssid config to bss information in AP-modeArik Nemtsov2011-09-142-1/+20
| | | | | | | | | | | | | | | | | | | | | | | | Set SSID information from nl80211 beacon parameters. Advertise changes in SSID to low level drivers. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | minstrel_ht: fix Open BA session request floodsChristian Lamparter2011-09-141-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Minstrel HT tries very hard to establish a BA session with each peer once there's some data on the way. However the stack does not inform minstrel if an aggregation session is already in place, so it keeps trying and wastes good cycles in the tx status path. [ 8149.946393] Open BA session requested for $AP tid 0 [ 8150.048765] Open BA session requested for $AP tid 0 [ 8150.174509] Open BA session requested for $AP tid 0 [ 8150.274376] Open BA session requested for $AP tid 0 ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Acked-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: stop tx before doing hw config and rate updateRajkumar Manoharan2011-09-142-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The assumption is that during the hw config, transmission was already stopped by mac80211. Sometimes the AP can be switching b/w the ht modes due to intolerant or etc where STA is in the middle of transmission. In such scenario, buffer overflow was observed at driver side. And also before updating the rate control, the frames are continued to xmited with older rates. This patch ensures that the frames are always xmitted with updated rates and avoid buffer overflow. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Stop forwarding mesh traffic when tx queues are fullJavier Cardona2011-09-143-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tx flow control for non-mesh modes of operation only needs to act on the net device queues: when the hardware queues are full we stop accepting traffic from the net device. In mesh, however, we also need to stop forwarding traffic. This patch checks the hardware queues before attempting to forward a mesh frame. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: check if mesh frame is in RMC after decryptThomas Pedersen2011-09-141-9/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To check whether a frame is in the RMC, we need access to the mesh header. This header is encrypted in encrypted data frames, so make this check after the frame has been decrypted. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: make ieee80211_send_bar available for driversFelix Fietkau2011-09-143-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | To properly maintain the peer's block ack window, the driver needs to be able to control the new starting sequence number that is sent along with the BlockAckReq frame. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: handle allocation failures in mesh_pathtbl_init()Dan Carpenter2011-09-131-2/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | The calls to kzalloc() weren't checked here and it upsets the static checkers. Obviously they're not super likely to fail, but we might as well add some error handling. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: add flag to indicate HW only Tx-agg setup supportArik Nemtsov2011-09-133-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | When this flag is set, Tx A-MPDU sessions will not be started by mac80211. This flag is required for devices that support Tx A-MPDU setup in hardware. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Remove unnecessary OOM logging messagesJoe Perches2011-09-1310-93/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removing unnecessary messages saves code and text. Site specific OOM messages are duplications of a generic MM out of memory message and aren't really useful, so just delete them. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Consolidate mesh path duplicated functionsJavier Cardona2011-09-131-42/+28
| | | | | | | | | | | | Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Consolidate {mesh,mpp}_path_flush into one functionJavier Cardona2011-09-131-39/+26
| | | | | | | | | | | | | | | Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Don't iterate twice over all mpaths when once in sufficientJavier Cardona2011-09-131-27/+37
| | | | | | | | | | | | | | | Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Remove redundant mesh path expiration checksJavier Cardona2011-09-131-6/+3
| | | | | | | | | | | | | | | Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Improve mpath state lockingJavier Cardona2011-09-132-11/+7
| | | | | | | | | | | | | | | | | | | | | | | | No need to take the mpath state lock when an mpath is removed. Also, no need checking the lock when reading mpath flags. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Remove mesh paths when an interface is removedJavier Cardona2011-09-134-3/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When an interface is removed, the mesh paths associated with it should also be removed. This fixes a bug we observed when reloading a device driver module without reloading mac80211s. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Fix RCU pointer dereference in mesh_path_discard_frame()Javier Cardona2011-09-131-1/+6
| | | | | | | | | | | | | | | | | | | | | Reported by Pedro Larbig (ASPj) Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: retry sending failed BAR frames later instead of tearing down aggrFelix Fietkau2011-09-132-1/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Unfortunately failed BAR tx attempts happen more frequently than I expected, and the resulting aggregation teardowns cause performance issues, as the aggregation session does not always get re-established properly. Instead of tearing down the entire aggr session, we can simply store the SSN of the last failed BAR tx attempt, wait for the first successful tx status event, and then send another BAR with the same SSN. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Defer tranmission of mesh path errorsJavier Cardona2011-09-131-2/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | Under failure conditions, the mesh stack sends PERR messages to the previous sender of the failed frame. This happens in the tx feedback path, in which the transmission queue lock may be taken. Avoid a deadlock by sending the path error via the pending queue. Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | Merge branch 'master' of ↵John W. Linville2011-09-132-15/+7
|\ \ \ | |/ / | | | | | | git://git.infradead.org/users/linville/wireless-next into for-davem
| * | mac80211: refactor skb copy to failq in mesh_path_move_to_queueJohn W. Linville2011-08-291-4/+4
| | | | | | | | | | | | | | | | | | This seems a bit less awkward... Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | net/mac80211/debugfs: Convert to kstrou8_from_userPeter Huewe2011-08-291-11/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch replaces the code for getting an number from a userspace buffer by a simple call to kstrou8_from_user. This makes it easier to read and less error prone. Since the old buffer was only 10 bytes long and the value is masked by a nibble-mask anyway, we don't need to use kstrtoul but rather kstrtou8. Kernel Version: v3.0-rc2 Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | Merge branch 'master' of ↵John W. Linville2011-08-2916-365/+1148
|\ \ \ | |/ / | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
| * | mac80211: add uapsd_queues and max_sp params fieldsEliad Peller2011-08-261-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add uapsd_queues and max_sp fields to ieee80211_sta. These fields might be needed by low-level drivers in order to configure the AP. Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: allow action frames with unknown BSSID in GO modeArik Nemtsov2011-08-261-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When operating as a P2P GO, we receive some P2P action frames where the BSSID is set to the peer MAC address. Specifically, this occurs for invitation responses. These are valid action frames and they should be passed up. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: fix race condition between assoc_done and first EAP packetGuy Eilam2011-08-264-60/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When associating to an AP, the station might miss the first EAP packet that the AP sends due to a race condition between the association success procedure and the rx flow in mac80211. In such cases, the packet might fall in ieee80211_rx_h_check due to the fact that the relevant rx->sta wasn't allocated yet. Allocation of the relevant station info struct before actually sending the association request and setting it with a new dummy_sta flag solve this problem. The station will accept only EAP packets from the AP while it is in the pre-association/dummy state. This dummy station entry is not seen by normal sta_info_get() calls, only by sta_info_get_bss_rx(). The driver is not notified for the first insertion of the dummy station. The driver is notified only after the association is complete and the dummy flag is removed from the station entry. That way, all the rest of the code flow should be untouched by this change. Signed-off-by: Guy Eilam <guy@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: refactor sta_info_insert_rcu to 3 main stagesGuy Eilam2011-08-261-53/+95
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Divided the sta_info_insert_rcu function to 3 mini-functions: sta_info_insert_check - the initial checks done when inserting a new station sta_info_insert_ibss - the function that handles the station addition for IBSS interfaces sta_info_insert_non_ibss - the function that handles the station addition in other cases The outer API was not changed. The refactoring was done for better usage of the different stages in the station addition in new scenarios added in the next commit. Signed-off-by: Guy Eilam <guy@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: mesh gate fixesThomas Pedersen2011-08-263-8/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since a v1 of the mesh gate series was accidentally applied, this patch contains the changes in v2. These are: - automatically make mesh gate a root node. - use TU_TO_EXP_TIME macro. - initialize timer instead of checking for NULL timer function. - cleanups. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | {nl,cfg,mac}80211: let userspace make meshif mesh gateJavier Cardona2011-08-243-1/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute, which will advertise this mesh node as being a mesh gate. NL80211_HWMP_ROOTMODE must be set or this will do nothing. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
View Lorry Controller Status