/* * arch/arm/mach-omap2/serial.c * * OMAP2 serial support. * * Copyright (C) 2005-2008 Nokia Corporation * Author: Paul Mundt * * Major rework for PM support by Kevin Hilman * * Based off of arch/arm/mach-omap/omap1/serial.c * * Copyright (C) 2009 Texas Instruments * Added OMAP4 support - Santosh Shilimkar #include #include #include #include #include #include #include #include #include #ifdef CONFIG_SERIAL_OMAP #include #endif #include #include #include #include #include #include #include "prm.h" #include "pm.h" #include "cm.h" #include "prm-regbits-34xx.h" #include "control.h" #define UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV 0x52 #define UART_OMAP_WER 0x17 /* Wake-up enable register */ #define UART_ERRATA_FIFO_FULL_ABORT (0x1 << 0) #define UART_ERRATA_i202_MDR1_ACCESS (0x1 << 1) /* * NOTE: By default the serial timeout is disabled as it causes lost characters * over the serial ports. This means that the UART clocks will stay on until * disabled via sysfs. This also causes that any deeper omap sleep states are * blocked. */ #define DEFAULT_TIMEOUT 0 #define MAX_UART_HWMOD_NAME_LEN 16 struct omap_uart_state { int num; int can_sleep; struct timer_list timer; u32 timeout; void __iomem *wk_st; void __iomem *wk_en; u32 wk_mask; u32 padconf; u32 dma_enabled; struct clk *ick; struct clk *fck; int clocked; int irq; int regshift; int irqflags; void __iomem *membase; resource_size_t mapbase; struct list_head node; struct omap_hwmod *oh; struct platform_device *pdev; u32 errata; #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM) int context_valid; /* Registers to be saved/restored for OFF-mode */ u16 dll; u16 dlh; u16 ier; u16 sysc; u16 scr; u16 wer; u16 mcr; #endif }; static LIST_HEAD(uart_list); static u8 num_uarts; /* * Since these idle/enable hooks are used in the idle path itself * which has interrupts disabled, use the non-locking versions of * the hwmod enable/disable functions. */ static int uart_idle_hwmod(struct omap_device *od) { _omap_hwmod_idle(od->hwmods[0]); return 0; } static int uart_enable_hwmod(struct omap_device *od) { _omap_hwmod_enable(od->hwmods[0]); return 0; } static struct omap_device_pm_latency omap_uart_latency[] = { { .deactivate_func = uart_idle_hwmod, .activate_func = uart_enable_hwmod, .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST, }, }; static inline unsigned int __serial_read_reg(struct uart_port *up, int offset) { offset <<= up->regshift; return (unsigned int)__raw_readb(up->membase + offset); } static inline unsigned int serial_read_reg(struct omap_uart_state *uart, int offset) { offset <<= uart->regshift; return (unsigned int)__raw_readb(uart->membase + offset); } static inline void __serial_write_reg(struct uart_port *up, int offset, int value) { offset <<= up->regshift; __raw_writeb(value, up->membase + offset); } static inline void serial_write_reg(struct omap_uart_state *uart, int offset, int value) { offset <<= uart->regshift; __raw_writeb(value, uart->membase + offset); } /* * Internal UARTs need to be initialized for the 8250 autoconfig to work * properly. Note that the TX watermark initialization may not be needed * once the 8250.c watermark handling code is merged. */ static inline void __init omap_uart_reset(struct omap_uart_state *uart) { serial_write_reg(uart, UART_OMAP_MDR1, 0x07); serial_write_reg(uart, UART_OMAP_SCR, 0x08); serial_write_reg(uart, UART_OMAP_MDR1, 0x00); } #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3) /* * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6) * The access to uart register after MDR1 Access * causes UART to corrupt data. * * Need a delay = * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS) * give 10 times as much */ static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val, u8 fcr_val) { u8 timeout = 255; serial_write_reg(uart, UART_OMAP_MDR1, mdr1_val); udelay(2); serial_write_reg(uart, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT | UART_FCR_CLEAR_RCVR); /* * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and * TX_FIFO_E bit is 1. */ while (UART_LSR_THRE != (serial_read_reg(uart, UART_LSR) & (UART_LSR_THRE | UART_LSR_DR))) { timeout--; if (!timeout) { /* Should *never* happen. we warn and carry on */ dev_crit(&uart->pdev->dev, "Errata i202: timedout %x\n", serial_read_reg(uart, UART_LSR)); break; } udelay(1); } } static void omap_uart_save_context(struct omap_uart_state *uart) { u16 lcr = 0; if (!enable_off_mode) return; lcr = serial_read_reg(uart, UART_LCR); serial_write_reg(uart, UART_LCR, 0xBF); uart->dll = serial_read_reg(uart, UART_DLL); uart->dlh = serial_read_reg(uart, UART_DLM); serial_write_reg(uart, UART_LCR, lcr); uart->ier = serial_read_reg(uart, UART_IER); uart->sysc = serial_read_reg(uart, UART_OMAP_SYSC); uart->scr = serial_read_reg(uart, UART_OMAP_SCR); uart->wer = serial_read_reg(uart, UART_OMAP_WER); serial_write_reg(uart, UART_LCR, 0x80); uart->mcr = serial_read_reg(uart, UART_MCR); serial_write_reg(uart, UART_LCR, lcr); uart->context_valid = 1; } static void omap_uart_restore_context(struct omap_uart_state *uart) { u16 efr = 0; if (!enable_off_mode) return; if (!uart->context_valid) return; uart->context_valid = 0; if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS) omap_uart_mdr1_errataset(uart, 0x07, 0xA0); else serial_write_reg(uart, UART_OMAP_MDR1, 0x7); serial_write_reg(uart, UART_LCR, 0xBF); /* Config B mode */ efr = serial_read_reg(uart, UART_EFR); serial_write_reg(uart, UART_EFR, UART_EFR_ECB); serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */ serial_write_reg(uart, UART_IER, 0x0); serial_write_reg(uart, UART_LCR, 0xBF); /* Config B mode */ serial_write_reg(uart, UART_DLL, uart->dll); serial_write_reg(uart, UART_DLM, uart->dlh); serial_write_reg(uart, UART_LCR, 0x0); /* Operational mode */ serial_write_reg(uart, UART_IER, uart->ier); serial_write_reg(uart, UART_LCR, 0x80); serial_write_reg(uart, UART_MCR, uart->mcr); serial_write_reg(uart, UART_LCR, 0xBF); /* Config B mode */ serial_write_reg(uart, UART_EFR, efr); serial_write_reg(uart, UART_LCR, UART_LCR_WLEN8); serial_write_reg(uart, UART_OMAP_SCR, uart->scr); serial_write_reg(uart, UART_OMAP_WER, uart->wer); serial_write_reg(uart, UART_OMAP_SYSC, uart->sysc); if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS) omap_uart_mdr1_errataset(uart, 0x00, 0xA1); else /* UART 16x mode */ serial_write_reg(uart, UART_OMAP_MDR1, 0x00); } #else static inline void omap_uart_save_context(struct omap_uart_state *uart) {} static inline void omap_uart_restore_context(struct omap_uart_state *uart) {} #endif /* CONFIG_PM && CONFIG_ARCH_OMAP3 */ static inline void omap_uart_enable_clocks(struct omap_uart_state *uart) { if (uart->clocked) return; omap_device_enable(uart->pdev); uart->clocked = 1; omap_uart_restore_context(uart); } #ifdef CONFIG_PM static inline void omap_uart_disable_clocks(struct omap_uart_state *uart) { if (!uart->clocked) return; omap_uart_save_context(uart); uart->clocked = 0; omap_device_idle(uart->pdev); } static void omap_uart_enable_wakeup(struct omap_uart_state *uart) { /* Set wake-enable bit */ if (uart->wk_en && uart->wk_mask) { u32 v = __raw_readl(uart->wk_en); v |= uart->wk_mask; __raw_writel(v, uart->wk_en); } /* Ensure IOPAD wake-enables are set */ if (cpu_is_omap34xx() && uart->padconf) { u16 v = omap_ctrl_readw(uart->padconf); v |= OMAP3_PADCONF_WAKEUPENABLE0; omap_ctrl_writew(v, uart->padconf); } } static void omap_uart_disable_wakeup(struct omap_uart_state *uart) { /* Clear wake-enable bit */ if (uart->wk_en && uart->wk_mask) { u32 v = __raw_readl(uart->wk_en); v &= ~uart->wk_mask; __raw_writel(v, uart->wk_en); } /* Ensure IOPAD wake-enables are cleared */ if (cpu_is_omap34xx() && uart->padconf) { u16 v = omap_ctrl_readw(uart->padconf); v &= ~OMAP3_PADCONF_WAKEUPENABLE0; omap_ctrl_writew(v, uart->padconf); } } static void omap_uart_smart_idle_enable(struct omap_uart_state *uart, int enable) { u8 idlemode; if (enable) { /** * Errata 2.15: [UART]:Cannot Acknowledge Idle Requests * in Smartidle Mode When Configured for DMA Operations. */ if (uart->dma_enabled) idlemode = HWMOD_IDLEMODE_FORCE; else idlemode = HWMOD_IDLEMODE_SMART; } else { idlemode = HWMOD_IDLEMODE_NO; } omap_hwmod_set_slave_idlemode(uart->oh, idlemode); } static void omap_uart_block_sleep(struct omap_uart_state *uart) { omap_uart_enable_clocks(uart); omap_uart_smart_idle_enable(uart, 0); uart->can_sleep = 0; if (uart->timeout) mod_timer(&uart->timer, jiffies + uart->timeout); else del_timer(&uart->timer); } static void omap_uart_allow_sleep(struct omap_uart_state *uart) { if (device_may_wakeup(&uart->pdev->dev)) omap_uart_enable_wakeup(uart); else omap_uart_disable_wakeup(uart); if (!uart->clocked) return; omap_uart_smart_idle_enable(uart, 1); uart->can_sleep = 1; del_timer(&uart->timer); } static void omap_uart_idle_timer(unsigned long data) { struct omap_uart_state *uart = (struct omap_uart_state *)data; omap_uart_allow_sleep(uart); } void omap_uart_prepare_idle(int num) { struct omap_uart_state *uart; list_for_each_entry(uart, &uart_list, node) { if (num == uart->num && uart->can_sleep) { omap_uart_disable_clocks(uart); return; } } } void omap_uart_resume_idle(int num) { struct omap_uart_state *uart; list_for_each_entry(uart, &uart_list, node) { if (num == uart->num) { omap_uart_enable_clocks(uart); /* Check for IO pad wakeup */ if (cpu_is_omap34xx() && uart->padconf) { u16 p = omap_ctrl_readw(uart->padconf); if (p & OMAP3_PADCONF_WAKEUPEVENT0) omap_uart_block_sleep(uart); } /* Check for normal UART wakeup */ if (__raw_readl(uart->wk_st) & uart->wk_mask) omap_uart_block_sleep(uart); return; } } } void omap_uart_prepare_suspend(void) { struct omap_uart_state *uart; list_for_each_entry(uart, &uart_list, node) { omap_uart_allow_sleep(uart); } } int omap_uart_can_sleep(void) { struct omap_uart_state *uart; int can_sleep = 1; list_for_each_entry(uart, &uart_list, node) { if (!uart->clocked) continue; if (!uart->can_sleep) { can_sleep = 0; continue; } /* This UART can now safely sleep. */ omap_uart_allow_sleep(uart); } return can_sleep; } /** * omap_uart_interrupt() * * This handler is used only to detect that *any* UART interrupt has * occurred. It does _nothing_ to handle the interrupt. Rather, * any UART interrupt will trigger the inactivity timer so the * UART will not idle or sleep for its timeout period. * **/ /* static int first_interrupt; */ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id) { struct omap_uart_state *uart = dev_id; omap_uart_block_sleep(uart); return IRQ_NONE; } static void omap_uart_idle_init(struct omap_uart_state *uart) { int ret; uart->can_sleep = 0; uart->timeout = DEFAULT_TIMEOUT; setup_timer(&uart->timer, omap_uart_idle_timer, (unsigned long) uart); if (uart->timeout) mod_timer(&uart->timer, jiffies + uart->timeout); omap_uart_smart_idle_enable(uart, 0); if (cpu_is_omap34xx()) { u32 mod = (uart->num > 1) ? OMAP3430_PER_MOD : CORE_MOD; u32 wk_mask = 0; u32 padconf = 0; uart->wk_en = OMAP34XX_PRM_REGADDR(mod, PM_WKEN1); uart->wk_st = OMAP34XX_PRM_REGADDR(mod, PM_WKST1); switch (uart->num) { case 0: wk_mask = OMAP3430_ST_UART1_MASK; padconf = 0x182; break; case 1: wk_mask = OMAP3430_ST_UART2_MASK; padconf = 0x17a; break; case 2: wk_mask = OMAP3430_ST_UART3_MASK; padconf = 0x19e; break; case 3: wk_mask = OMAP3630_ST_UART4_MASK; padconf = 0x0d2; break; } uart->wk_mask = wk_mask; uart->padconf = padconf; } else if (cpu_is_omap24xx()) { u32 wk_mask = 0; u32 wk_en = PM_WKEN1, wk_st = PM_WKST1; switch (uart->num) { case 0: wk_mask = OMAP24XX_ST_UART1_MASK; break; case 1: wk_mask = OMAP24XX_ST_UART2_MASK; break; case 2: wk_en = OMAP24XX_PM_WKEN2; wk_st = OMAP24XX_PM_WKST2; wk_mask = OMAP24XX_ST_UART3_MASK; break; } uart->wk_mask = wk_mask; if (cpu_is_omap2430()) { uart->wk_en = OMAP2430_PRM_REGADDR(CORE_MOD, wk_en); uart->wk_st = OMAP2430_PRM_REGADDR(CORE_MOD, wk_st); } else if (cpu_is_omap2420()) { uart->wk_en = OMAP2420_PRM_REGADDR(CORE_MOD, wk_en); uart->wk_st = OMAP2420_PRM_REGADDR(CORE_MOD, wk_st); } } else { uart->wk_en = NULL; uart->wk_st = NULL; uart->wk_mask = 0; uart->padconf = 0; } uart->irqflags |= IRQF_SHARED; ret = request_threaded_irq(uart->irq, NULL, omap_uart_interrupt, IRQF_SHARED, "serial idle", (void *)uart); WARN_ON(ret); } void omap_uart_enable_irqs(int enable) { int ret; struct omap_uart_state *uart; list_for_each_entry(uart, &uart_list, node) { if (enable) { pm_runtime_put_sync(&uart->pdev->dev); ret = request_threaded_irq(uart->irq, NULL, omap_uart_interrupt, IRQF_SHARED, "serial idle", (void *)uart); } else { pm_runtime_get_noresume(&uart->pdev->dev); free_irq(uart->irq, (void *)uart); } } } static ssize_t sleep_timeout_show(struct device *dev, struct device_attribute *attr, char *buf) { struct platform_device *pdev = to_platform_device(dev); struct omap_device *odev = to_omap_device(pdev); struct omap_uart_state *uart = odev->hwmods[0]->dev_attr; return sprintf(buf, "%u\n", uart->timeout / HZ); } static ssize_t sleep_timeout_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t n) { struct platform_device *pdev = to_platform_device(dev); struct omap_device *odev = to_omap_device(pdev); struct omap_uart_state *uart = odev->hwmods[0]->dev_attr; unsigned int value; if (sscanf(buf, "%u", &value) != 1) { dev_err(dev, "sleep_timeout_store: Invalid value\n"); return -EINVAL; } uart->timeout = value * HZ; if (uart->timeout) mod_timer(&uart->timer, jiffies + uart->timeout); else /* A zero value means disable timeout feature */ omap_uart_block_sleep(uart); return n; } static DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); #define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr)) #else static inline void omap_uart_idle_init(struct omap_uart_state *uart) {} static void omap_uart_block_sleep(struct omap_uart_state *uart) { /* Needed to enable UART clocks when built without CONFIG_PM */ omap_uart_enable_clocks(uart); } #define DEV_CREATE_FILE(dev, attr) #endif /* CONFIG_PM */ #ifndef CONFIG_SERIAL_OMAP /* * Override the default 8250 read handler: mem_serial_in() * Empty RX fifo read causes an abort on omap3630 and omap4 * This function makes sure that an empty rx fifo is not read on these silicons * (OMAP1/2/3430 are not affected) */ static unsigned int serial_in_override(struct uart_port *up, int offset) { if (UART_RX == offset) { unsigned int lsr; lsr = __serial_read_reg(up, UART_LSR); if (!(lsr & UART_LSR_DR)) return -EPERM; } return __serial_read_reg(up, offset); } static void serial_out_override(struct uart_port *up, int offset, int value) { unsigned int status, tmout = 10000; status = __serial_read_reg(up, UART_LSR); while (!(status & UART_LSR_THRE)) { /* Wait up to 10ms for the character(s) to be sent. */ if (--tmout == 0) break; udelay(1); status = __serial_read_reg(up, UART_LSR); } __serial_write_reg(up, offset, value); } #endif void __init omap_serial_early_init(void) { int i = 0; do { char oh_name[MAX_UART_HWMOD_NAME_LEN]; struct omap_hwmod *oh; struct omap_uart_state *uart; snprintf(oh_name, MAX_UART_HWMOD_NAME_LEN, "uart%d", i + 1); oh = omap_hwmod_lookup(oh_name); if (!oh) break; uart = kzalloc(sizeof(struct omap_uart_state), GFP_KERNEL); if (WARN_ON(!uart)) return; uart->oh = oh; uart->num = i++; list_add_tail(&uart->node, &uart_list); num_uarts++; /* * NOTE: omap_hwmod_init() has not yet been called, * so no hwmod functions will work yet. */ /* * During UART early init, device need to be probed * to determine SoC specific init before omap_device * is ready. Therefore, don't allow idle here */ uart->oh->flags |= HWMOD_INIT_NO_IDLE | HWMOD_INIT_NO_RESET; } while (1); } /** * omap_serial_init_port() - initialize single serial port * @port: serial port number (0-3) * * This function initialies serial driver for given @port only. * Platforms can call this function instead of omap_serial_init() * if they don't plan to use all available UARTs as serial ports. * * Don't mix calls to omap_serial_init_port() and omap_serial_init(), * use only one of the two. */ void __init omap_serial_init_port(int port) { struct omap_uart_state *uart; struct omap_hwmod *oh; struct omap_device *od; void *pdata = NULL; u32 pdata_size = 0; char *name; #ifndef CONFIG_SERIAL_OMAP struct plat_serial8250_port ports[2] = { {}, {.flags = 0}, }; struct plat_serial8250_port *p = &ports[0]; #else struct omap_uart_port_info omap_up; #endif if (WARN_ON(port < 0)) return; if (WARN_ON(port >= num_uarts)) return; list_for_each_entry(uart, &uart_list, node) if (port == uart->num) break; oh = uart->oh; uart->dma_enabled = 0; #ifndef CONFIG_SERIAL_OMAP name = "serial8250"; /* * !! 8250 driver does not use standard IORESOURCE* It * has it's own custom pdata that can be taken from * the hwmod resource data. But, this needs to be * done after the build. * * ?? does it have to be done before the register ?? * YES, because platform_device_data_add() copies * pdata, it does not use a pointer. */ p->flags = UPF_BOOT_AUTOCONF; p->iotype = UPIO_MEM; p->regshift = 2; p->uartclk = OMAP24XX_BASE_BAUD * 16; p->irq = oh->mpu_irqs[0].irq; p->mapbase = oh->slaves[0]->addr->pa_start; p->membase = omap_hwmod_get_mpu_rt_va(oh); p->irqflags = IRQF_SHARED; p->private_data = uart; /* * omap44xx: Never read empty UART fifo * omap3xxx: Never read empty UART fifo on UARTs * with IP rev >=0x52 */ uart->regshift = p->regshift; uart->membase = p->membase; if (cpu_is_omap44xx()) uart->errata |= UART_ERRATA_FIFO_FULL_ABORT; else if ((serial_read_reg(uart, UART_OMAP_MVER) & 0xFF) >= UART_OMAP_NO_EMPTY_FIFO_READ_IP_REV) uart->errata |= UART_ERRATA_FIFO_FULL_ABORT; if (uart->errata & UART_ERRATA_FIFO_FULL_ABORT) { p->serial_in = serial_in_override; p->serial_out = serial_out_override; } pdata = &ports[0]; pdata_size = 2 * sizeof(struct plat_serial8250_port); #else name = DRIVER_NAME; omap_up.dma_enabled = uart->dma_enabled; omap_up.uartclk = OMAP24XX_BASE_BAUD * 16; omap_up.mapbase = oh->slaves[0]->addr->pa_start; omap_up.membase = omap_hwmod_get_mpu_rt_va(oh); omap_up.irqflags = IRQF_SHARED; omap_up.flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ; pdata = &omap_up; pdata_size = sizeof(struct omap_uart_port_info); #endif if (WARN_ON(!oh)) return; od = omap_device_build(name, uart->num, oh, pdata, pdata_size, omap_uart_latency, ARRAY_SIZE(omap_uart_latency), false); WARN(IS_ERR(od), "Could not build omap_device for %s: %s.\n", name, oh->name); uart->irq = oh->mpu_irqs[0].irq; uart->regshift = 2; uart->mapbase = oh->slaves[0]->addr->pa_start; uart->membase = omap_hwmod_get_mpu_rt_va(oh); uart->pdev = &od->pdev; oh->dev_attr = uart; /* * Because of early UART probing, UART did not get idled * on init. Now that omap_device is ready, ensure full idle * before doing omap_device_enable(). */ omap_hwmod_idle(uart->oh); omap_device_enable(uart->pdev); omap_uart_idle_init(uart); omap_uart_reset(uart); omap_hwmod_enable_wakeup(uart->oh); omap_device_idle(uart->pdev); /* * Need to block sleep long enough for interrupt driven * driver to start. Console driver is in polling mode * so device needs to be kept enabled while polling driver * is in use. */ if (uart->timeout) uart->timeout = (30 * HZ); omap_uart_block_sleep(uart); uart->timeout = DEFAULT_TIMEOUT; if ((cpu_is_omap34xx() && uart->padconf) || (uart->wk_en && uart->wk_mask)) { device_init_wakeup(&od->pdev.dev, true); DEV_CREATE_FILE(&od->pdev.dev, &dev_attr_sleep_timeout); } /* Enable the MDR1 errata for OMAP3 */ if (cpu_is_omap34xx()) uart->errata |= UART_ERRATA_i202_MDR1_ACCESS; } /** * omap_serial_init() - initialize all supported serial ports * * Initializes all available UARTs as serial ports. Platforms * can call this function when they want to have default behaviour * for serial ports (e.g initialize them all as serial ports). */ void __init omap_serial_init(void) { struct omap_uart_state *uart; list_for_each_entry(uart, &uart_list, node) omap_serial_init_port(uart->num); }