# # USB Serial device configuration # menuconfig USB_SERIAL tristate "USB Serial Converter support" depends on TTY ---help--- Say Y here if you have a USB device that provides normal serial ports, or acts like a serial device, and you want to connect it to your USB bus. Please read for more information on the specifics of the different devices that are supported, and on how to use them. To compile this driver as a module, choose M here: the module will be called usbserial. if USB_SERIAL config USB_SERIAL_CONSOLE bool "USB Serial Console device support" depends on USB_SERIAL=y ---help--- If you say Y here, it will be possible to use a USB to serial converter port as the system console (the system console is the device which receives all kernel messages and warnings and which allows logins in single user mode). This could be useful if some terminal or printer is connected to that serial port. Even if you say Y here, the currently visible virtual console (/dev/tty0) will still be used as the system console by default, but you can alter that using a kernel command line option such as "console=ttyUSB0". (Try "man bootparam" or see the documentation of your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) If you don't have a VGA card installed and you say Y here, the kernel will automatically use the first USB to serial converter port, /dev/ttyUSB0, as system console. If unsure, say N. config USB_SERIAL_GENERIC bool "USB Generic Serial Driver" help Say Y here if you want to use the generic USB serial driver. Please read for more information on using this driver. It is recommended that the "USB Serial converter support" be compiled as a module for this driver to be used properly. config USB_SERIAL_SIMPLE tristate "USB Serial Simple Driver" help Say Y here to use the USB serial "simple" driver. This driver handles a wide range of very simple devices, all in one driver. Specifically, it supports: - Suunto ANT+ USB device. - Medtronic CareLink USB device - Fundamental Software dongle. - HP4x calculators - a number of Motorola phones - Motorola Tetra devices - Novatel Wireless GPS receivers - Siemens USB/MPI adapter. - ViVOtech ViVOpay USB device. - Infineon Modem Flashloader USB interface - ZIO Motherboard USB serial interface To compile this driver as a module, choose M here: the module will be called usb-serial-simple. config USB_SERIAL_AIRCABLE tristate "USB AIRcable Bluetooth Dongle Driver" help Say Y here if you want to use USB AIRcable Bluetooth Dongle. To compile this driver as a module, choose M here: the module will be called aircable. config USB_SERIAL_ARK3116 tristate "USB ARK Micro 3116 USB Serial Driver" help Say Y here if you want to use a ARK Micro 3116 USB to Serial device. To compile this driver as a module, choose M here: the module will be called ark3116 config USB_SERIAL_BELKIN tristate "USB Belkin and Peracom Single Port Serial Driver" help Say Y here if you want to use a Belkin USB Serial single port adaptor (F5U103 is one of the model numbers) or the Peracom single port USB to serial adapter. To compile this driver as a module, choose M here: the module will be called belkin_sa. config USB_SERIAL_CH341 tristate "USB Winchiphead CH341 Single Port Serial Driver" help Say Y here if you want to use a Winchiphead CH341 single port USB to serial adapter. To compile this driver as a module, choose M here: the module will be called ch341. config USB_SERIAL_WHITEHEAT tristate "USB ConnectTech WhiteHEAT Serial Driver" select USB_EZUSB_FX2 help Say Y here if you want to use a ConnectTech WhiteHEAT 4 port USB to serial converter device. To compile this driver as a module, choose M here: the module will be called whiteheat. config USB_SERIAL_DIGI_ACCELEPORT tristate "USB Digi International AccelePort USB Serial Driver" ---help--- Say Y here if you want to use Digi AccelePort USB 2 or 4 devices, 2 port (plus parallel port) and 4 port USB serial converters. The parallel port on the USB 2 appears as a third serial port on Linux. The Digi Acceleport USB 8 is not yet supported by this driver. This driver works under SMP with the usb-uhci driver. It does not work under SMP with the uhci driver. To compile this driver as a module, choose M here: the module will be called digi_acceleport. config USB_SERIAL_CP210X tristate "USB CP210x family of UART Bridge Controllers" help Say Y here if you want to use a CP2101/CP2102/CP2103 based USB to RS232 converters. To compile this driver as a module, choose M here: the module will be called cp210x. config USB_SERIAL_CYPRESS_M8 tristate "USB Cypress M8 USB Serial Driver" help Say Y here if you want to use a device that contains the Cypress USB to Serial microcontroller, such as the DeLorme Earthmate GPS. Attempted SMP support... send bug reports! Supported microcontrollers in the CY4601 family are: CY7C63741 CY7C63742 CY7C63743 CY7C64013 To compile this driver as a module, choose M here: the module will be called cypress_m8. config USB_SERIAL_EMPEG tristate "USB Empeg empeg-car Mark I/II Driver" help Say Y here if you want to connect to your Empeg empeg-car Mark I/II mp3 player via USB. The driver uses a single ttyUSB{0,1,2,...} device node. See for more tidbits of information. To compile this driver as a module, choose M here: the module will be called empeg. config USB_SERIAL_FTDI_SIO tristate "USB FTDI Single Port Serial Driver" ---help--- Say Y here if you want to use a FTDI SIO single port USB to serial converter device. The implementation I have is called the USC-1000. This driver has also be tested with the 245 and 232 devices. See for more information on this driver and the device. To compile this driver as a module, choose M here: the module will be called ftdi_sio. config USB_SERIAL_VISOR tristate "USB Handspring Visor / Palm m50x / Sony Clie Driver" help Say Y here if you want to connect to your HandSpring Visor, Palm m500 or m505 through its USB docking station. See for more information on using this driver. To compile this driver as a module, choose M here: the module will be called visor. config USB_SERIAL_IPAQ tristate "USB PocketPC PDA Driver" help Say Y here if you want to connect to your Compaq iPAQ, HP Jornada or any other PDA running Windows CE 3.0 or PocketPC 2002 using a USB cradle/cable. For information on using the driver, read . To compile this driver as a module, choose M here: the module will be called ipaq. config USB_SERIAL_IR tristate "USB IR Dongle Serial Driver" help Say Y here if you want to enable simple serial support for USB IrDA devices. This is useful if you do not want to use the full IrDA stack. To compile this driver as a module, choose M here: the module will be called ir-usb. config USB_SERIAL_EDGEPORT tristate "USB Inside Out Edgeport Serial Driver" ---help--- Say Y here if you want to use any of the following devices from Inside Out Networks (Digi): Edgeport/4 Rapidport/4 Edgeport/4t Edgeport/2 Edgeport/4i Edgeport/2i Edgeport/421 Edgeport/21 Edgeport/8 Edgeport/8 Dual Edgeport/2D8 Edgeport/4D8 Edgeport/8i Edgeport/2 DIN Edgeport/4 DIN Edgeport/16 Dual To compile this driver as a module, choose M here: the module will be called io_edgeport. config USB_SERIAL_EDGEPORT_TI tristate "USB Inside Out Edgeport Serial Driver (TI devices)" help Say Y here if you want to use any of the devices from Inside Out Networks (Digi) that are not supported by the io_edgeport driver. This includes the Edgeport/1 device. To compile this driver as a module, choose M here: the module will be called io_ti. config USB_SERIAL_F81232 tristate "USB Fintek F81232 Single Port Serial Driver" help Say Y here if you want to use the Fintek F81232 single port usb to serial adapter. To compile this driver as a module, choose M here: the module will be called f81232. config USB_SERIAL_GARMIN tristate "USB Garmin GPS driver" help Say Y here if you want to connect to your Garmin GPS. Should work with most Garmin GPS devices which have a native USB port. See for the latest version of the driver. To compile this driver as a module, choose M here: the module will be called garmin_gps. config USB_SERIAL_IPW tristate "USB IPWireless (3G UMTS TDD) Driver" select USB_SERIAL_WWAN help Say Y here if you want to use a IPWireless USB modem such as the ones supplied by Axity3G/Sentech South Africa. To compile this driver as a module, choose M here: the module will be called ipw. config USB_SERIAL_IUU tristate "USB Infinity USB Unlimited Phoenix Driver" help Say Y here if you want to use a IUU in phoenix mode and get an extra ttyUSBx device. More information available on http://eczema.ecze.com/iuu_phoenix.html To compile this driver as a module, choose M here: the module will be called iuu_phoenix.o config USB_SERIAL_KEYSPAN_PDA tristate "USB Keyspan PDA Single Port Serial Driver" select USB_EZUSB_FX2 help Say Y here if you want to use a Keyspan PDA single port USB to serial converter device. This driver makes use of firmware developed from scratch by Brian Warner. To compile this driver as a module, choose M here: the module will be called keyspan_pda. config USB_SERIAL_KEYSPAN tristate "USB Keyspan USA-xxx Serial Driver" select USB_EZUSB_FX2 ---help--- Say Y here if you want to use Keyspan USB to serial converter devices. This driver makes use of Keyspan's official firmware and was developed with their support. You must also include firmware to support your particular device(s). See for more information. To compile this driver as a module, choose M here: the module will be called keyspan. config USB_SERIAL_KEYSPAN_MPR bool "USB Keyspan MPR Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the Keyspan MPR converter. config USB_SERIAL_KEYSPAN_USA28 bool "USB Keyspan USA-28 Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-28 converter. config USB_SERIAL_KEYSPAN_USA28X bool "USB Keyspan USA-28X Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-28X converter. Be sure you have a USA-28X, there are also 28XA and 28XB models, the label underneath has the actual part number. config USB_SERIAL_KEYSPAN_USA28XA bool "USB Keyspan USA-28XA Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-28XA converter. Be sure you have a USA-28XA, there are also 28X and 28XB models, the label underneath has the actual part number. config USB_SERIAL_KEYSPAN_USA28XB bool "USB Keyspan USA-28XB Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-28XB converter. Be sure you have a USA-28XB, there are also 28X and 28XA models, the label underneath has the actual part number. config USB_SERIAL_KEYSPAN_USA19 bool "USB Keyspan USA-19 Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-19 converter. config USB_SERIAL_KEYSPAN_USA18X bool "USB Keyspan USA-18X Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-18X converter. config USB_SERIAL_KEYSPAN_USA19W bool "USB Keyspan USA-19W Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-19W converter. config USB_SERIAL_KEYSPAN_USA19QW bool "USB Keyspan USA-19QW Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-19QW converter. config USB_SERIAL_KEYSPAN_USA19QI bool "USB Keyspan USA-19QI Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-19QI converter. config USB_SERIAL_KEYSPAN_USA49W bool "USB Keyspan USA-49W Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-49W converter. config USB_SERIAL_KEYSPAN_USA49WLC bool "USB Keyspan USA-49WLC Firmware" depends on USB_SERIAL_KEYSPAN && FIRMWARE_IN_KERNEL help Say Y here to include firmware for the USA-49WLC converter. config USB_SERIAL_KLSI tristate "USB KL5KUSB105 (Palmconnect) Driver" ---help--- Say Y here if you want to use a KL5KUSB105 - based single port serial adapter. The most widely known -- and currently the only tested -- device in this category is the PalmConnect USB Serial adapter sold by Palm Inc. for use with their Palm III and Palm V series PDAs. Please read for more information. To compile this driver as a module, choose M here: the module will be called kl5kusb105. config USB_SERIAL_KOBIL_SCT tristate "USB KOBIL chipcard reader" ---help--- Say Y here if you want to use one of the following KOBIL USB chipcard readers: - USB TWIN - KAAN Standard Plus - KAAN SIM - SecOVID Reader Plus - B1 Professional - KAAN Professional Note that you need a current CT-API. To compile this driver as a module, choose M here: the module will be called kobil_sct. config USB_SERIAL_MCT_U232 tristate "USB MCT Single Port Serial Driver" ---help--- Say Y here if you want to use a USB Serial single port adapter from Magic Control Technology Corp. (U232 is one of the model numbers). This driver also works with Sitecom U232-P25 and D-Link DU-H3SP USB BAY, Belkin F5U109, and Belkin F5U409 devices. To compile this driver as a module, choose M here: the module will be called mct_u232. config USB_SERIAL_METRO tristate "USB Metrologic Instruments USB-POS Barcode Scanner Driver" ---help--- Say Y here if you want to use a USB POS Metrologic barcode scanner. To compile this driver as a module, choose M here: the module will be called metro-usb. config USB_SERIAL_MOS7720 tristate "USB Moschip 7720 Serial Driver" ---help--- Say Y here if you want to use USB Serial single and double port adapters from Moschip Semiconductor Tech. To compile this driver as a module, choose M here: the module will be called mos7720. config USB_SERIAL_MOS7715_PARPORT bool "Support for parallel port on the Moschip 7715" depends on USB_SERIAL_MOS7720 depends on PARPORT=y || PARPORT=USB_SERIAL_MOS7720 select PARPORT_NOT_PC ---help--- Say Y if you have a Moschip 7715 device and would like to use the parallel port it provides. The port will register with the parport subsystem as a low-level driver. config USB_SERIAL_MOS7840 tristate "USB Moschip 7840/7820 USB Serial Driver" ---help--- Say Y here if you want to use a MCS7840 Quad-Serial or MCS7820 Dual-Serial port device from MosChip Semiconductor. The MCS7840 and MCS7820 have been developed to connect a wide range of standard serial devices to a USB host. The MCS7840 has a USB device controller connected to four (4) individual UARTs while the MCS7820 controller connects to two (2) individual UARTs. To compile this driver as a module, choose M here: the module will be called mos7840. If unsure, choose N. config USB_SERIAL_MXUPORT tristate "USB Moxa UPORT Serial Driver" ---help--- Say Y here if you want to use a MOXA UPort Serial hub. This driver supports: [2 Port] - UPort 1250 : 2 Port RS-232/422/485 USB to Serial Hub - UPort 1250I : 2 Port RS-232/422/485 USB to Serial Hub with Isolation [4 Port] - UPort 1410 : 4 Port RS-232 USB to Serial Hub - UPort 1450 : 4 Port RS-232/422/485 USB to Serial Hub - UPort 1450I : 4 Port RS-232/422/485 USB to Serial Hub with Isolation [8 Port] - UPort 1610-8 : 8 Port RS-232 USB to Serial Hub - UPort 1650-8 : 8 Port RS-232/422/485 USB to Serial Hub [16 Port] - UPort 1610-16 : 16 Port RS-232 USB to Serial Hub - UPort 1650-16 : 16 Port RS-232/422/485 USB to Serial Hub To compile this driver as a module, choose M here: the module will be called mxuport. config USB_SERIAL_NAVMAN tristate "USB Navman GPS device" help To compile this driver as a module, choose M here: the module will be called navman. config USB_SERIAL_PL2303 tristate "USB Prolific 2303 Single Port Serial Driver" help Say Y here if you want to use the PL2303 USB Serial single port adapter from Prolific. To compile this driver as a module, choose M here: the module will be called pl2303. config USB_SERIAL_OTI6858 tristate "USB Ours Technology Inc. OTi-6858 USB To RS232 Bridge Controller" help Say Y here if you want to use the OTi-6858 single port USB to serial converter device. To compile this driver as a module, choose M here: the module will be called oti6858. config USB_SERIAL_QCAUX tristate "USB Qualcomm Auxiliary Serial Port Driver" help Say Y here if you want to use the auxiliary serial ports provided by many modems based on Qualcomm chipsets. These ports often use a proprietary protocol called DM and cannot be used for AT- or PPP-based communication. To compile this driver as a module, choose M here: the module will be called qcaux. If unsure, choose N. config USB_SERIAL_QUALCOMM tristate "USB Qualcomm Serial modem" select USB_SERIAL_WWAN help Say Y here if you have a Qualcomm USB modem device. These are usually wireless cellular modems. To compile this driver as a module, choose M here: the module will be called qcserial. config USB_SERIAL_SPCP8X5 tristate "USB SPCP8x5 USB To Serial Driver" help Say Y here if you want to use the spcp8x5 converter chip. This is commonly found in some Z-Wave USB devices. To compile this driver as a module, choose M here: the module will be called spcp8x5. config USB_SERIAL_SAFE tristate "USB Safe Serial (Encapsulated) Driver" config USB_SERIAL_SAFE_PADDED bool "USB Secure Encapsulated Driver - Padded" depends on USB_SERIAL_SAFE config USB_SERIAL_SIERRAWIRELESS tristate "USB Sierra Wireless Driver" help Say M here if you want to use Sierra Wireless devices. Many devices have a feature known as TRU-Install. For those devices to work properly, the USB Storage Sierra feature must be enabled. To compile this driver as a module, choose M here: the module will be called sierra. config USB_SERIAL_SYMBOL tristate "USB Symbol Barcode driver (serial mode)" help Say Y here if you want to use a Symbol USB Barcode device in serial emulation mode. To compile this driver as a module, choose M here: the module will be called symbolserial. config USB_SERIAL_TI tristate "USB TI 3410/5052 Serial Driver" help Say Y here if you want to use the TI USB 3410 or 5052 serial devices. To compile this driver as a module, choose M here: the module will be called ti_usb_3410_5052. config USB_SERIAL_CYBERJACK tristate "USB REINER SCT cyberJack pinpad/e-com chipcard reader" ---help--- Say Y here if you want to use a cyberJack pinpad/e-com USB chipcard reader. This is an interface to ISO 7816 compatible contact-based chipcards, e.g. GSM SIMs. To compile this driver as a module, choose M here: the module will be called cyberjack. If unsure, say N. config USB_SERIAL_XIRCOM tristate "USB Xircom / Entregra Single Port Serial Driver" select USB_EZUSB_FX2 help Say Y here if you want to use a Xircom or Entregra single port USB to serial converter device. This driver makes use of firmware developed from scratch by Brian Warner. To compile this driver as a module, choose M here: the module will be called keyspan_pda. config USB_SERIAL_WWAN tristate config USB_SERIAL_OPTION tristate "USB driver for GSM and CDMA modems" select USB_SERIAL_WWAN help Say Y here if you have a GSM or CDMA modem that's connected to USB. This driver also supports several PCMCIA cards which have a built-in OHCI-USB adapter and an internally-connected GSM modem. The USB bus on these cards is not accessible externally. Supported devices include (some of?) those made by: Option, Huawei, Audiovox, Novatel Wireless, or Anydata. To compile this driver as a module, choose M here: the module will be called option. If this driver doesn't recognize your device, it might be accessible via the FTDI_SIO driver. config USB_SERIAL_OMNINET tristate "USB ZyXEL omni.net LCD Plus Driver" help Say Y here if you want to use a ZyXEL omni.net LCD ISDN TA. To compile this driver as a module, choose M here: the module will be called omninet. config USB_SERIAL_OPTICON tristate "USB Opticon Barcode driver (serial mode)" help Say Y here if you want to use a Opticon USB Barcode device in serial emulation mode. To compile this driver as a module, choose M here: the module will be called opticon. config USB_SERIAL_XSENS_MT tristate "Xsens motion tracker serial interface driver" help Say Y here if you want to use Xsens motion trackers. This driver supports the new generation of motion trackers by Xsens. Older devices can be accessed using the FTDI_SIO driver. To compile this driver as a module, choose M here: the module will be called xsens_mt. config USB_SERIAL_WISHBONE tristate "USB-Wishbone adapter interface driver" help Say Y here if you want to use a USB attached Wishbone bus. Wishbone is an open hardware SoC bus commonly used in FPGA designs. Bus access can be serialized using the Etherbone protocol . This driver is intended to be used with devices which attach their internal Wishbone bus to a USB serial interface using the Etherbone protocol. A userspace library is required to speak the protocol made available by this driver as ttyUSBx. To compile this driver as a module, choose M here: the module will be called wishbone-serial. config USB_SERIAL_SSU100 tristate "USB Quatech SSU-100 Single Port Serial Driver" help Say Y here if you want to use the Quatech SSU-100 single port usb to serial adapter. To compile this driver as a module, choose M here: the module will be called ssu100. config USB_SERIAL_QT2 tristate "USB Quatech Serial Driver for USB 2 devices" help Say Y here if you want to use the Quatech USB 2 serial adapters. To compile this driver as a module, choose M here: the module will be called quatech-serial. config USB_SERIAL_DEBUG tristate "USB Debugging Device" help Say Y here if you have a USB debugging device used to receive debugging data from another machine. The most common of these devices is the NetChip TurboCONNECT device. To compile this driver as a module, choose M here: the module will be called usb-debug. endif # USB_SERIAL