/* SPDX-License-Identifier: GPL-2.0 */ /* * ethtool.h: Defines for Linux ethtool. * * Copyright (C) 1998 David S. Miller (davem@redhat.com) * Copyright 2001 Jeff Garzik * Portions Copyright 2001 Sun Microsystems (thockin@sun.com) * Portions Copyright 2002 Intel (eli.kupermann@intel.com, * christopher.leech@intel.com, * scott.feldman@intel.com) * Portions Copyright (C) Sun Microsystems 2008 */ #ifndef _LINUX_ETHTOOL_H #define _LINUX_ETHTOOL_H #include #include #include #ifdef CONFIG_COMPAT struct compat_ethtool_rx_flow_spec { u32 flow_type; union ethtool_flow_union h_u; struct ethtool_flow_ext h_ext; union ethtool_flow_union m_u; struct ethtool_flow_ext m_ext; compat_u64 ring_cookie; u32 location; }; struct compat_ethtool_rxnfc { u32 cmd; u32 flow_type; compat_u64 data; struct compat_ethtool_rx_flow_spec fs; u32 rule_cnt; u32 rule_locs[]; }; #endif /* CONFIG_COMPAT */ #include /** * enum ethtool_phys_id_state - indicator state for physical identification * @ETHTOOL_ID_INACTIVE: Physical ID indicator should be deactivated * @ETHTOOL_ID_ACTIVE: Physical ID indicator should be activated * @ETHTOOL_ID_ON: LED should be turned on (used iff %ETHTOOL_ID_ACTIVE * is not supported) * @ETHTOOL_ID_OFF: LED should be turned off (used iff %ETHTOOL_ID_ACTIVE * is not supported) */ enum ethtool_phys_id_state { ETHTOOL_ID_INACTIVE, ETHTOOL_ID_ACTIVE, ETHTOOL_ID_ON, ETHTOOL_ID_OFF }; enum { ETH_RSS_HASH_TOP_BIT, /* Configurable RSS hash function - Toeplitz */ ETH_RSS_HASH_XOR_BIT, /* Configurable RSS hash function - Xor */ ETH_RSS_HASH_CRC32_BIT, /* Configurable RSS hash function - Crc32 */ /* * Add your fresh new hash function bits above and remember to update * rss_hash_func_strings[] in ethtool.c */ ETH_RSS_HASH_FUNCS_COUNT }; #define __ETH_RSS_HASH_BIT(bit) ((u32)1 << (bit)) #define __ETH_RSS_HASH(name) __ETH_RSS_HASH_BIT(ETH_RSS_HASH_##name##_BIT) #define ETH_RSS_HASH_TOP __ETH_RSS_HASH(TOP) #define ETH_RSS_HASH_XOR __ETH_RSS_HASH(XOR) #define ETH_RSS_HASH_CRC32 __ETH_RSS_HASH(CRC32) #define ETH_RSS_HASH_UNKNOWN 0 #define ETH_RSS_HASH_NO_CHANGE 0 struct net_device; /* Some generic methods drivers may use in their ethtool_ops */ u32 ethtool_op_get_link(struct net_device *dev); int ethtool_op_get_ts_info(struct net_device *dev, struct ethtool_ts_info *eti); /** * struct ethtool_link_ext_state_info - link extended state and substate. */ struct ethtool_link_ext_state_info { enum ethtool_link_ext_state link_ext_state; union { enum ethtool_link_ext_substate_autoneg autoneg; enum ethtool_link_ext_substate_link_training link_training; enum ethtool_link_ext_substate_link_logical_mismatch link_logical_mismatch; enum ethtool_link_ext_substate_bad_signal_integrity bad_signal_integrity; enum ethtool_link_ext_substate_cable_issue cable_issue; u8 __link_ext_substate; }; }; /** * ethtool_rxfh_indir_default - get default value for RX flow hash indirection * @index: Index in RX flow hash indirection table * @n_rx_rings: Number of RX rings to use * * This function provides the default policy for RX flow hash indirection. */ static inline u32 ethtool_rxfh_indir_default(u32 index, u32 n_rx_rings) { return index % n_rx_rings; } /* declare a link mode bitmap */ #define __ETHTOOL_DECLARE_LINK_MODE_MASK(name) \ DECLARE_BITMAP(name, __ETHTOOL_LINK_MODE_MASK_NBITS) /* drivers must ignore base.cmd and base.link_mode_masks_nwords * fields, but they are allowed to overwrite them (will be ignored). */ struct ethtool_link_ksettings { struct ethtool_link_settings base; struct { __ETHTOOL_DECLARE_LINK_MODE_MASK(supported); __ETHTOOL_DECLARE_LINK_MODE_MASK(advertising); __ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising); } link_modes; }; /** * ethtool_link_ksettings_zero_link_mode - clear link_ksettings link mode mask * @ptr : pointer to struct ethtool_link_ksettings * @name : one of supported/advertising/lp_advertising */ #define ethtool_link_ksettings_zero_link_mode(ptr, name) \ bitmap_zero((ptr)->link_modes.name, __ETHTOOL_LINK_MODE_MASK_NBITS) /** * ethtool_link_ksettings_add_link_mode - set bit in link_ksettings * link mode mask * @ptr : pointer to struct ethtool_link_ksettings * @name : one of supported/advertising/lp_advertising * @mode : one of the ETHTOOL_LINK_MODE_*_BIT * (not atomic, no bound checking) */ #define ethtool_link_ksettings_add_link_mode(ptr, name, mode) \ __set_bit(ETHTOOL_LINK_MODE_ ## mode ## _BIT, (ptr)->link_modes.name) /** * ethtool_link_ksettings_del_link_mode - clear bit in link_ksettings * link mode mask * @ptr : pointer to struct ethtool_link_ksettings * @name : one of supported/advertising/lp_advertising * @mode : one of the ETHTOOL_LINK_MODE_*_BIT * (not atomic, no bound checking) */ #define ethtool_link_ksettings_del_link_mode(ptr, name, mode) \ __clear_bit(ETHTOOL_LINK_MODE_ ## mode ## _BIT, (ptr)->link_modes.name) /** * ethtool_link_ksettings_test_link_mode - test bit in ksettings link mode mask * @ptr : pointer to struct ethtool_link_ksettings * @name : one of supported/advertising/lp_advertising * @mode : one of the ETHTOOL_LINK_MODE_*_BIT * (not atomic, no bound checking) * * Returns true/false. */ #define ethtool_link_ksettings_test_link_mode(ptr, name, mode) \ test_bit(ETHTOOL_LINK_MODE_ ## mode ## _BIT, (ptr)->link_modes.name) extern int __ethtool_get_link_ksettings(struct net_device *dev, struct ethtool_link_ksettings *link_ksettings); /** * ethtool_intersect_link_masks - Given two link masks, AND them together * @dst: first mask and where result is stored * @src: second mask to intersect with * * Given two link mode masks, AND them together and save the result in dst. */ void ethtool_intersect_link_masks(struct ethtool_link_ksettings *dst, struct ethtool_link_ksettings *src); void ethtool_convert_legacy_u32_to_link_mode(unsigned long *dst, u32 legacy_u32); /* return false if src had higher bits set. lower bits always updated. */ bool ethtool_convert_link_mode_to_legacy_u32(u32 *legacy_u32, const unsigned long *src); #define ETHTOOL_COALESCE_RX_USECS BIT(0) #define ETHTOOL_COALESCE_RX_MAX_FRAMES BIT(1) #define ETHTOOL_COALESCE_RX_USECS_IRQ BIT(2) #define ETHTOOL_COALESCE_RX_MAX_FRAMES_IRQ BIT(3) #define ETHTOOL_COALESCE_TX_USECS BIT(4) #define ETHTOOL_COALESCE_TX_MAX_FRAMES BIT(5) #define ETHTOOL_COALESCE_TX_USECS_IRQ BIT(6) #define ETHTOOL_COALESCE_TX_MAX_FRAMES_IRQ BIT(7) #define ETHTOOL_COALESCE_STATS_BLOCK_USECS BIT(8) #define ETHTOOL_COALESCE_USE_ADAPTIVE_RX BIT(9) #define ETHTOOL_COALESCE_USE_ADAPTIVE_TX BIT(10) #define ETHTOOL_COALESCE_PKT_RATE_LOW BIT(11) #define ETHTOOL_COALESCE_RX_USECS_LOW BIT(12) #define ETHTOOL_COALESCE_RX_MAX_FRAMES_LOW BIT(13) #define ETHTOOL_COALESCE_TX_USECS_LOW BIT(14) #define ETHTOOL_COALESCE_TX_MAX_FRAMES_LOW BIT(15) #define ETHTOOL_COALESCE_PKT_RATE_HIGH BIT(16) #define ETHTOOL_COALESCE_RX_USECS_HIGH BIT(17) #define ETHTOOL_COALESCE_RX_MAX_FRAMES_HIGH BIT(18) #define ETHTOOL_COALESCE_TX_USECS_HIGH BIT(19) #define ETHTOOL_COALESCE_TX_MAX_FRAMES_HIGH BIT(20) #define ETHTOOL_COALESCE_RATE_SAMPLE_INTERVAL BIT(21) #define ETHTOOL_COALESCE_USECS \ (ETHTOOL_COALESCE_RX_USECS | ETHTOOL_COALESCE_TX_USECS) #define ETHTOOL_COALESCE_MAX_FRAMES \ (ETHTOOL_COALESCE_RX_MAX_FRAMES | ETHTOOL_COALESCE_TX_MAX_FRAMES) #define ETHTOOL_COALESCE_USECS_IRQ \ (ETHTOOL_COALESCE_RX_USECS_IRQ | ETHTOOL_COALESCE_TX_USECS_IRQ) #define ETHTOOL_COALESCE_MAX_FRAMES_IRQ \ (ETHTOOL_COALESCE_RX_MAX_FRAMES_IRQ | \ ETHTOOL_COALESCE_TX_MAX_FRAMES_IRQ) #define ETHTOOL_COALESCE_USE_ADAPTIVE \ (ETHTOOL_COALESCE_USE_ADAPTIVE_RX | ETHTOOL_COALESCE_USE_ADAPTIVE_TX) #define ETHTOOL_COALESCE_USECS_LOW_HIGH \ (ETHTOOL_COALESCE_RX_USECS_LOW | ETHTOOL_COALESCE_TX_USECS_LOW | \ ETHTOOL_COALESCE_RX_USECS_HIGH | ETHTOOL_COALESCE_TX_USECS_HIGH) #define ETHTOOL_COALESCE_MAX_FRAMES_LOW_HIGH \ (ETHTOOL_COALESCE_RX_MAX_FRAMES_LOW | \ ETHTOOL_COALESCE_TX_MAX_FRAMES_LOW | \ ETHTOOL_COALESCE_RX_MAX_FRAMES_HIGH | \ ETHTOOL_COALESCE_TX_MAX_FRAMES_HIGH) #define ETHTOOL_COALESCE_PKT_RATE_RX_USECS \ (ETHTOOL_COALESCE_USE_ADAPTIVE_RX | \ ETHTOOL_COALESCE_RX_USECS_LOW | ETHTOOL_COALESCE_RX_USECS_HIGH | \ ETHTOOL_COALESCE_PKT_RATE_LOW | ETHTOOL_COALESCE_PKT_RATE_HIGH | \ ETHTOOL_COALESCE_RATE_SAMPLE_INTERVAL) #define ETHTOOL_STAT_NOT_SET (~0ULL) /** * struct ethtool_pause_stats - statistics for IEEE 802.3x pause frames * @tx_pause_frames: transmitted pause frame count. Reported to user space * as %ETHTOOL_A_PAUSE_STAT_TX_FRAMES. * * Equivalent to `30.3.4.2 aPAUSEMACCtrlFramesTransmitted` * from the standard. * * @rx_pause_frames: received pause frame count. Reported to user space * as %ETHTOOL_A_PAUSE_STAT_RX_FRAMES. Equivalent to: * * Equivalent to `30.3.4.3 aPAUSEMACCtrlFramesReceived` * from the standard. */ struct ethtool_pause_stats { u64 tx_pause_frames; u64 rx_pause_frames; }; /** * struct ethtool_ops - optional netdev operations * @supported_coalesce_params: supported types of interrupt coalescing. * @get_drvinfo: Report driver/device information. Should only set the * @driver, @version, @fw_version and @bus_info fields. If not * implemented, the @driver and @bus_info fields will be filled in * according to the netdev's parent device. * @get_regs_len: Get buffer length required for @get_regs * @get_regs: Get device registers * @get_wol: Report whether Wake-on-Lan is enabled * @set_wol: Turn Wake-on-Lan on or off. Returns a negative error code * or zero. * @get_msglevel: Report driver message level. This should be the value * of the @msg_enable field used by netif logging functions. * @set_msglevel: Set driver message level * @nway_reset: Restart autonegotiation. Returns a negative error code * or zero. * @get_link: Report whether physical link is up. Will only be called if * the netdev is up. Should usually be set to ethtool_op_get_link(), * which uses netif_carrier_ok(). * @get_link_ext_state: Report link extended state. Should set link_ext_state and * link_ext_substate (link_ext_substate of 0 means link_ext_substate is unknown, * do not attach ext_substate attribute to netlink message). If link_ext_state * and link_ext_substate are unknown, return -ENODATA. If not implemented, * link_ext_state and link_ext_substate will not be sent to userspace. * @get_eeprom: Read data from the device EEPROM. * Should fill in the magic field. Don't need to check len for zero * or wraparound. Fill in the data argument with the eeprom values * from offset to offset + len. Update len to the amount read. * Returns an error or zero. * @set_eeprom: Write data to the device EEPROM. * Should validate the magic field. Don't need to check len for zero * or wraparound. Update len to the amount written. Returns an error * or zero. * @get_coalesce: Get interrupt coalescing parameters. Returns a negative * error code or zero. * @set_coalesce: Set interrupt coalescing parameters. Supported coalescing * types should be set in @supported_coalesce_params. * Returns a negative error code or zero. * @get_ringparam: Report ring sizes * @set_ringparam: Set ring sizes. Returns a negative error code or zero. * @get_pause_stats: Report pause frame statistics. Drivers must not zero * statistics which they don't report. The stats structure is initialized * to ETHTOOL_STAT_NOT_SET indicating driver does not report statistics. * @get_pauseparam: Report pause parameters * @set_pauseparam: Set pause parameters. Returns a negative error code * or zero. * @self_test: Run specified self-tests * @get_strings: Return a set of strings that describe the requested objects * @set_phys_id: Identify the physical devices, e.g. by flashing an LED * attached to it. The implementation may update the indicator * asynchronously or synchronously, but in either case it must return * quickly. It is initially called with the argument %ETHTOOL_ID_ACTIVE, * and must either activate asynchronous updates and return zero, return * a negative error or return a positive frequency for synchronous * indication (e.g. 1 for one on/off cycle per second). If it returns * a frequency then it will be called again at intervals with the * argument %ETHTOOL_ID_ON or %ETHTOOL_ID_OFF and should set the state of * the indicator accordingly. Finally, it is called with the argument * %ETHTOOL_ID_INACTIVE and must deactivate the indicator. Returns a * negative error code or zero. * @get_ethtool_stats: Return extended statistics about the device. * This is only useful if the device maintains statistics not * included in &struct rtnl_link_stats64. * @begin: Function to be called before any other operation. Returns a * negative error code or zero. * @complete: Function to be called after any other operation except * @begin. Will be called even if the other operation failed. * @get_priv_flags: Report driver-specific feature flags. * @set_priv_flags: Set driver-specific feature flags. Returns a negative * error code or zero. * @get_sset_count: Get number of strings that @get_strings will write. * @get_rxnfc: Get RX flow classification rules. Returns a negative * error code or zero. * @set_rxnfc: Set RX flow classification rules. Returns a negative * error code or zero. * @flash_device: Write a firmware image to device's flash memory. * Returns a negative error code or zero. * @reset: Reset (part of) the device, as specified by a bitmask of * flags from &enum ethtool_reset_flags. Returns a negative * error code or zero. * @get_rxfh_key_size: Get the size of the RX flow hash key. * Returns zero if not supported for this specific device. * @get_rxfh_indir_size: Get the size of the RX flow hash indirection table. * Returns zero if not supported for this specific device. * @get_rxfh: Get the contents of the RX flow hash indirection table, hash key * and/or hash function. * Returns a negative error code or zero. * @set_rxfh: Set the contents of the RX flow hash indirection table, hash * key, and/or hash function. Arguments which are set to %NULL or zero * will remain unchanged. * Returns a negative error code or zero. An error code must be returned * if at least one unsupported change was requested. * @get_rxfh_context: Get the contents of the RX flow hash indirection table, * hash key, and/or hash function assiciated to the given rss context. * Returns a negative error code or zero. * @set_rxfh_context: Create, remove and configure RSS contexts. Allows setting * the contents of the RX flow hash indirection table, hash key, and/or * hash function associated to the given context. Arguments which are set * to %NULL or zero will remain unchanged. * Returns a negative error code or zero. An error code must be returned * if at least one unsupported change was requested. * @get_channels: Get number of channels. * @set_channels: Set number of channels. Returns a negative error code or * zero. * @get_dump_flag: Get dump flag indicating current dump length, version, * and flag of the device. * @get_dump_data: Get dump data. * @set_dump: Set dump specific flags to the device. * @get_ts_info: Get the time stamping and PTP hardware clock capabilities. * Drivers supporting transmit time stamps in software should set this to * ethtool_op_get_ts_info(). * @get_module_info: Get the size and type of the eeprom contained within * a plug-in module. * @get_module_eeprom: Get the eeprom information from the plug-in module * @get_eee: Get Energy-Efficient (EEE) supported and status. * @set_eee: Set EEE status (enable/disable) as well as LPI timers. * @get_per_queue_coalesce: Get interrupt coalescing parameters per queue. * It must check that the given queue number is valid. If neither a RX nor * a TX queue has this number, return -EINVAL. If only a RX queue or a TX * queue has this number, set the inapplicable fields to ~0 and return 0. * Returns a negative error code or zero. * @set_per_queue_coalesce: Set interrupt coalescing parameters per queue. * It must check that the given queue number is valid. If neither a RX nor * a TX queue has this number, return -EINVAL. If only a RX queue or a TX * queue has this number, ignore the inapplicable fields. Supported * coalescing types should be set in @supported_coalesce_params. * Returns a negative error code or zero. * @get_link_ksettings: Get various device settings including Ethernet link * settings. The %cmd and %link_mode_masks_nwords fields should be * ignored (use %__ETHTOOL_LINK_MODE_MASK_NBITS instead of the latter), * any change to them will be overwritten by kernel. Returns a negative * error code or zero. * @set_link_ksettings: Set various device settings including Ethernet link * settings. The %cmd and %link_mode_masks_nwords fields should be * ignored (use %__ETHTOOL_LINK_MODE_MASK_NBITS instead of the latter), * any change to them will be overwritten by kernel. Returns a negative * error code or zero. * @get_fecparam: Get the network device Forward Error Correction parameters. * @set_fecparam: Set the network device Forward Error Correction parameters. * @get_ethtool_phy_stats: Return extended statistics about the PHY device. * This is only useful if the device maintains PHY statistics and * cannot use the standard PHY library helpers. * * All operations are optional (i.e. the function pointer may be set * to %NULL) and callers must take this into account. Callers must * hold the RTNL lock. * * See the structures used by these operations for further documentation. * Note that for all operations using a structure ending with a zero- * length array, the array is allocated separately in the kernel and * is passed to the driver as an additional parameter. * * See &struct net_device and &struct net_device_ops for documentation * of the generic netdev features interface. */ struct ethtool_ops { u32 supported_coalesce_params; void (*get_drvinfo)(struct net_device *, struct ethtool_drvinfo *); int (*get_regs_len)(struct net_device *); void (*get_regs)(struct net_device *, struct ethtool_regs *, void *); void (*get_wol)(struct net_device *, struct ethtool_wolinfo *); int (*set_wol)(struct net_device *, struct ethtool_wolinfo *); u32 (*get_msglevel)(struct net_device *); void (*set_msglevel)(struct net_device *, u32); int (*nway_reset)(struct net_device *); u32 (*get_link)(struct net_device *); int (*get_link_ext_state)(struct net_device *, struct ethtool_link_ext_state_info *); int (*get_eeprom_len)(struct net_device *); int (*get_eeprom)(struct net_device *, struct ethtool_eeprom *, u8 *); int (*set_eeprom)(struct net_device *, struct ethtool_eeprom *, u8 *); int (*get_coalesce)(struct net_device *, struct ethtool_coalesce *); int (*set_coalesce)(struct net_device *, struct ethtool_coalesce *); void (*get_ringparam)(struct net_device *, struct ethtool_ringparam *); int (*set_ringparam)(struct net_device *, struct ethtool_ringparam *); void (*get_pause_stats)(struct net_device *dev, struct ethtool_pause_stats *pause_stats); void (*get_pauseparam)(struct net_device *, struct ethtool_pauseparam*); int (*set_pauseparam)(struct net_device *, struct ethtool_pauseparam*); void (*self_test)(struct net_device *, struct ethtool_test *, u64 *); void (*get_strings)(struct net_device *, u32 stringset, u8 *); int (*set_phys_id)(struct net_device *, enum ethtool_phys_id_state); void (*get_ethtool_stats)(struct net_device *, struct ethtool_stats *, u64 *); int (*begin)(struct net_device *); void (*complete)(struct net_device *); u32 (*get_priv_flags)(struct net_device *); int (*set_priv_flags)(struct net_device *, u32); int (*get_sset_count)(struct net_device *, int); int (*get_rxnfc)(struct net_device *, struct ethtool_rxnfc *, u32 *rule_locs); int (*set_rxnfc)(struct net_device *, struct ethtool_rxnfc *); int (*flash_device)(struct net_device *, struct ethtool_flash *); int (*reset)(struct net_device *, u32 *); u32 (*get_rxfh_key_size)(struct net_device *); u32 (*get_rxfh_indir_size)(struct net_device *); int (*get_rxfh)(struct net_device *, u32 *indir, u8 *key, u8 *hfunc); int (*set_rxfh)(struct net_device *, const u32 *indir, const u8 *key, const u8 hfunc); int (*get_rxfh_context)(struct net_device *, u32 *indir, u8 *key, u8 *hfunc, u32 rss_context); int (*set_rxfh_context)(struct net_device *, const u32 *indir, const u8 *key, const u8 hfunc, u32 *rss_context, bool delete); void (*get_channels)(struct net_device *, struct ethtool_channels *); int (*set_channels)(struct net_device *, struct ethtool_channels *); int (*get_dump_flag)(struct net_device *, struct ethtool_dump *); int (*get_dump_data)(struct net_device *, struct ethtool_dump *, void *); int (*set_dump)(struct net_device *, struct ethtool_dump *); int (*get_ts_info)(struct net_device *, struct ethtool_ts_info *); int (*get_module_info)(struct net_device *, struct ethtool_modinfo *); int (*get_module_eeprom)(struct net_device *, struct ethtool_eeprom *, u8 *); int (*get_eee)(struct net_device *, struct ethtool_eee *); int (*set_eee)(struct net_device *, struct ethtool_eee *); int (*get_tunable)(struct net_device *, const struct ethtool_tunable *, void *); int (*set_tunable)(struct net_device *, const struct ethtool_tunable *, const void *); int (*get_per_queue_coalesce)(struct net_device *, u32, struct ethtool_coalesce *); int (*set_per_queue_coalesce)(struct net_device *, u32, struct ethtool_coalesce *); int (*get_link_ksettings)(struct net_device *, struct ethtool_link_ksettings *); int (*set_link_ksettings)(struct net_device *, const struct ethtool_link_ksettings *); int (*get_fecparam)(struct net_device *, struct ethtool_fecparam *); int (*set_fecparam)(struct net_device *, struct ethtool_fecparam *); void (*get_ethtool_phy_stats)(struct net_device *, struct ethtool_stats *, u64 *); int (*get_phy_tunable)(struct net_device *, const struct ethtool_tunable *, void *); int (*set_phy_tunable)(struct net_device *, const struct ethtool_tunable *, const void *); }; int ethtool_check_ops(const struct ethtool_ops *ops); struct ethtool_rx_flow_rule { struct flow_rule *rule; unsigned long priv[]; }; struct ethtool_rx_flow_spec_input { const struct ethtool_rx_flow_spec *fs; u32 rss_ctx; }; struct ethtool_rx_flow_rule * ethtool_rx_flow_rule_create(const struct ethtool_rx_flow_spec_input *input); void ethtool_rx_flow_rule_destroy(struct ethtool_rx_flow_rule *rule); bool ethtool_virtdev_validate_cmd(const struct ethtool_link_ksettings *cmd); int ethtool_virtdev_set_link_ksettings(struct net_device *dev, const struct ethtool_link_ksettings *cmd, u32 *dev_speed, u8 *dev_duplex); struct netlink_ext_ack; struct phy_device; struct phy_tdr_config; /** * struct ethtool_phy_ops - Optional PHY device options * @get_sset_count: Get number of strings that @get_strings will write. * @get_strings: Return a set of strings that describe the requested objects * @get_stats: Return extended statistics about the PHY device. * @start_cable_test - Start a cable test * @start_cable_test_tdr - Start a Time Domain Reflectometry cable test * * All operations are optional (i.e. the function pointer may be set to %NULL) * and callers must take this into account. Callers must hold the RTNL lock. */ struct ethtool_phy_ops { int (*get_sset_count)(struct phy_device *dev); int (*get_strings)(struct phy_device *dev, u8 *data); int (*get_stats)(struct phy_device *dev, struct ethtool_stats *stats, u64 *data); int (*start_cable_test)(struct phy_device *phydev, struct netlink_ext_ack *extack); int (*start_cable_test_tdr)(struct phy_device *phydev, struct netlink_ext_ack *extack, const struct phy_tdr_config *config); }; /** * ethtool_set_ethtool_phy_ops - Set the ethtool_phy_ops singleton * @ops: Ethtool PHY operations to set */ void ethtool_set_ethtool_phy_ops(const struct ethtool_phy_ops *ops); #endif /* _LINUX_ETHTOOL_H */