diff options
Diffstat (limited to 'arch')
70 files changed, 1367 insertions, 3631 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index db3c5414223e..3a45547b20e7 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -755,7 +755,7 @@ config ARCH_S3C64XX select ATAGS select CLKDEV_LOOKUP select CLKSRC_SAMSUNG_PWM - select COMMON_CLK + select COMMON_CLK_SAMSUNG select CPU_V6K select GENERIC_CLOCKEVENTS select GPIO_SAMSUNG @@ -836,7 +836,7 @@ config ARCH_EXYNOS select ARCH_REQUIRE_GPIOLIB select ARCH_SPARSEMEM_ENABLE select ARM_GIC - select COMMON_CLK + select COMMON_CLK_SAMSUNG select CPU_V7 select GENERIC_CLOCKEVENTS select HAVE_S3C2410_I2C if I2C @@ -844,6 +844,7 @@ config ARCH_EXYNOS select HAVE_S3C_RTC if RTC_CLASS select NEED_MACH_MEMORY_H select SPARSE_IRQ + select SRAM select USE_OF help Support for SAMSUNG's EXYNOS SoCs (EXYNOS4/5) diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 377b7c364033..b20c46233bd9 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ exynos5420-arndale-octa.dtb \ + exynos5420-peach-pit.dtb \ exynos5420-smdk5420.dtb \ exynos5440-sd5v1.dtb \ exynos5440-ssdk5440.dtb diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index 2f8bcd068d17..58ff8e28c74f 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -129,12 +129,10 @@ status = "disabled"; #address-cells = <1>; #size-cells = <1>; + #clock-cells = <1>; + clock-output-names = "cam_a_clkout", "cam_b_clkout"; ranges; - clock_cam: clock-controller { - #clock-cells = <1>; - }; - fimc_0: fimc@11800000 { compatible = "samsung,exynos4210-fimc"; reg = <0x11800000 0x1000>; @@ -371,6 +369,8 @@ interrupts = <0 60 0>; clocks = <&clock CLK_I2C2>; clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_bus>; status = "disabled"; }; @@ -382,6 +382,8 @@ interrupts = <0 61 0>; clocks = <&clock CLK_I2C3>; clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_bus>; status = "disabled"; }; @@ -393,6 +395,8 @@ interrupts = <0 62 0>; clocks = <&clock CLK_I2C4>; clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_bus>; status = "disabled"; }; @@ -404,6 +408,8 @@ interrupts = <0 63 0>; clocks = <&clock CLK_I2C5>; clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_bus>; status = "disabled"; }; @@ -415,6 +421,8 @@ interrupts = <0 64 0>; clocks = <&clock CLK_I2C6>; clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c6_bus>; status = "disabled"; }; @@ -426,6 +434,8 @@ interrupts = <0 65 0>; clocks = <&clock CLK_I2C7>; clock-names = "i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c7_bus>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts index 63e34b24b04f..9296dee10e26 100644 --- a/arch/arm/boot/dts/exynos4210-universal_c210.dts +++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts @@ -28,6 +28,21 @@ bootargs = "console=ttySAC2,115200N8 root=/dev/mmcblk0p5 rw rootwait earlyprintk panic=5 maxcpus=1"; }; + sysram@02020000 { + smp-sysram@0 { + status = "disabled"; + }; + + smp-sysram@5000 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x5000 0x1000>; + }; + + smp-sysram@1f000 { + status = "disabled"; + }; + }; + mct@10050000 { compatible = "none"; }; diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi index cacf6140dd2f..ee3001f38821 100644 --- a/arch/arm/boot/dts/exynos4210.dtsi +++ b/arch/arm/boot/dts/exynos4210.dtsi @@ -31,6 +31,24 @@ pinctrl2 = &pinctrl_2; }; + sysram@02020000 { + compatible = "mmio-sram"; + reg = <0x02020000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x02020000 0x20000>; + + smp-sysram@0 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x0 0x1000>; + }; + + smp-sysram@1f000 { + compatible = "samsung,exynos4210-sysram-ns"; + reg = <0x1f000 0x1000>; + }; + }; + pd_lcd1: lcd1-power-domain@10023CA0 { compatible = "samsung,exynos4210-pd"; reg = <0x10023CA0 0x20>; diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts index 9583563dd0ef..f621fd976815 100644 --- a/arch/arm/boot/dts/exynos4412-trats2.dts +++ b/arch/arm/boot/dts/exynos4412-trats2.dts @@ -20,7 +20,7 @@ compatible = "samsung,trats2", "samsung,exynos4412", "samsung,exynos4"; aliases { - i2c8 = &i2c_ak8975; + i2c9 = &i2c_ak8975; }; memory { @@ -80,7 +80,24 @@ enable-active-high; }; - /* More to come */ + cam_af_reg: voltage-regulator-3 { + compatible = "regulator-fixed"; + regulator-name = "CAM_AF"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpm0 4 0>; + enable-active-high; + }; + + cam_isp_core_reg: voltage-regulator-4 { + compatible = "regulator-fixed"; + regulator-name = "CAM_ISP_CORE_1.2V_EN"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + gpio = <&gpm0 3 0>; + enable-active-high; + regulator-always-on; + }; }; gpio-keys { @@ -140,6 +157,38 @@ }; }; + i2c_0: i2c@13860000 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c0_bus>; + pinctrl-names = "default"; + status = "okay"; + + s5c73m3@3c { + compatible = "samsung,s5c73m3"; + reg = <0x3c>; + standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */ + xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */ + vdd-int-supply = <&buck9_reg>; + vddio-cis-supply = <&ldo9_reg>; + vdda-supply = <&ldo17_reg>; + vddio-host-supply = <&ldo18_reg>; + vdd-af-supply = <&cam_af_reg>; + vdd-reg-supply = <&cam_io_reg>; + clock-frequency = <24000000>; + /* CAM_A_CLKOUT */ + clocks = <&camera 0>; + clock-names = "cis_extclk"; + port { + s5c73m3_ep: endpoint { + remote-endpoint = <&csis0_ep>; + data-lanes = <1 2 3 4>; + }; + }; + }; + }; + i2c@138D0000 { samsung,i2c-sda-delay = <100>; samsung,i2c-slave-addr = <0x10>; @@ -586,8 +635,8 @@ status = "okay"; }; - camera { - pinctrl-0 = <&cam_port_b_clk_active>; + camera: camera { + pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>; pinctrl-names = "default"; status = "okay"; @@ -607,6 +656,23 @@ status = "okay"; }; + csis_0: csis@11880000 { + status = "okay"; + vddcore-supply = <&ldo8_reg>; + vddio-supply = <&ldo10_reg>; + clock-frequency = <176000000>; + + /* Camera C (3) MIPI CSI-2 (CSIS0) */ + port@3 { + reg = <3>; + csis0_ep: endpoint { + remote-endpoint = <&s5c73m3_ep>; + data-lanes = <1 2 3 4>; + samsung,csis-hs-settle = <12>; + }; + }; + }; + csis_1: csis@11890000 { vddcore-supply = <&ldo8_reg>; vddio-supply = <&ldo10_reg>; @@ -647,10 +713,11 @@ reg = <0x10>; svdda-supply = <&cam_io_reg>; svddio-supply = <&ldo19_reg>; + afvdd-supply = <&ldo19_reg>; clock-frequency = <24000000>; /* CAM_B_CLKOUT */ - clocks = <&clock_cam 1>; - clock-names = "mclk"; + clocks = <&camera 1>; + clock-names = "extclk"; samsung,camclk-out = <1>; gpios = <&gpm1 6 0>; diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi index c4a9306f8529..70e3765b51ee 100644 --- a/arch/arm/boot/dts/exynos4x12.dtsi +++ b/arch/arm/boot/dts/exynos4x12.dtsi @@ -37,6 +37,24 @@ interrupts = <2 2>, <3 2>, <18 2>, <19 2>; }; + sysram@02020000 { + compatible = "mmio-sram"; + reg = <0x02020000 0x40000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x02020000 0x40000>; + + smp-sysram@0 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x0 0x1000>; + }; + + smp-sysram@2f000 { + compatible = "samsung,exynos4210-sysram-ns"; + reg = <0x2f000 0x1000>; + }; + }; + pd_isp: isp-power-domain@10023CA0 { compatible = "samsung,exynos4210-pd"; reg = <0x10023CA0 0x20>; diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index 37423314a028..e44693e2cfda 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -72,6 +72,24 @@ }; }; + sysram@02020000 { + compatible = "mmio-sram"; + reg = <0x02020000 0x30000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x02020000 0x30000>; + + smp-sysram@0 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x0 0x1000>; + }; + + smp-sysram@2f000 { + compatible = "samsung,exynos4210-sysram-ns"; + reg = <0x2f000 0x1000>; + }; + }; + pd_gsc: gsc-power-domain@10044000 { compatible = "samsung,exynos4210-pd"; reg = <0x10044000 0x20>; diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts new file mode 100644 index 000000000000..fae33dddac39 --- /dev/null +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts @@ -0,0 +1,147 @@ +/* + * Google Peach Pit Rev 6+ board device tree source + * + * Copyright (c) 2014 Google, Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "exynos5420.dtsi" + +/ { + model = "Google Peach Pit Rev 6+"; + + compatible = "google,pit-rev16", + "google,pit-rev15", "google,pit-rev14", + "google,pit-rev13", "google,pit-rev12", + "google,pit-rev11", "google,pit-rev10", + "google,pit-rev9", "google,pit-rev8", + "google,pit-rev7", "google,pit-rev6", + "google,pit", "google,peach","samsung,exynos5420", + "samsung,exynos5"; + + memory { + reg = <0x20000000 0x80000000>; + }; + + fixed-rate-clocks { + oscclk { + compatible = "samsung,exynos5420-oscclk"; + clock-frequency = <24000000>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&power_key_irq>; + + power { + label = "Power"; + gpios = <&gpx1 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + gpio-key,wakeup; + }; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 1000000 0>; + brightness-levels = <0 100 500 1000 1500 2000 2500 2800>; + default-brightness-level = <7>; + pinctrl-0 = <&pwm0_out>; + pinctrl-names = "default"; + }; +}; + +&pinctrl_0 { + tpm_irq: tpm-irq { + samsung,pins = "gpx1-0"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + power_key_irq: power-key-irq { + samsung,pins = "gpx1-2"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; +}; + +&rtc { + status = "okay"; +}; + +&uart_3 { + status = "okay"; +}; + +&mmc_0 { + status = "okay"; + num-slots = <1>; + broken-cd; + caps2-mmc-hs200-1_8v; + supports-highspeed; + non-removable; + card-detect-delay = <200>; + clock-frequency = <400000000>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <0 4>; + samsung,dw-mshc-ddr-timing = <0 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + + slot@0 { + reg = <0>; + bus-width = <8>; + }; +}; + +&mmc_2 { + status = "okay"; + num-slots = <1>; + supports-highspeed; + card-detect-delay = <200>; + clock-frequency = <400000000>; + samsung,dw-mshc-ciu-div = <3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; + pinctrl-names = "default"; + pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + + slot@0 { + reg = <0>; + bus-width = <4>; + }; +}; + +&hsi2c_9 { + status = "okay"; + clock-frequency = <400000>; + + tpm@20 { + compatible = "infineon,slb9645tt"; + reg = <0x20>; + + /* Unused irq; but still need to configure the pins */ + pinctrl-names = "default"; + pinctrl-0 = <&tpm_irq>; + }; +}; + +/* + * Use longest HW watchdog in SoC (32 seconds) since the hardware + * watchdog provides no debugging information (compared to soft/hard + * lockup detectors) and so should be last resort. + */ +&watchdog { + timeout-sec = <32>; +}; diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi index e62c8eb57438..ba686e40eac7 100644 --- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi +++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi @@ -624,6 +624,34 @@ samsung,pin-drv = <0>; }; + pwm0_out: pwm0-out { + samsung,pins = "gpb2-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + pwm1_out: pwm1-out { + samsung,pins = "gpb2-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + pwm2_out: pwm2-out { + samsung,pins = "gpb2-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + pwm3_out: pwm3-out { + samsung,pins = "gpb2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + i2c7_hs_bus: i2c7-hs-bus { samsung,pins = "gpb2-2", "gpb2-3"; samsung,pin-function = <3>; diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index c3a9a66c5767..3c530722e8dc 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -58,6 +58,7 @@ compatible = "arm,cortex-a15"; reg = <0x0>; clock-frequency = <1800000000>; + cci-control-port = <&cci_control1>; }; cpu1: cpu@1 { @@ -65,6 +66,7 @@ compatible = "arm,cortex-a15"; reg = <0x1>; clock-frequency = <1800000000>; + cci-control-port = <&cci_control1>; }; cpu2: cpu@2 { @@ -72,6 +74,7 @@ compatible = "arm,cortex-a15"; reg = <0x2>; clock-frequency = <1800000000>; + cci-control-port = <&cci_control1>; }; cpu3: cpu@3 { @@ -79,6 +82,7 @@ compatible = "arm,cortex-a15"; reg = <0x3>; clock-frequency = <1800000000>; + cci-control-port = <&cci_control1>; }; cpu4: cpu@100 { @@ -86,6 +90,7 @@ compatible = "arm,cortex-a7"; reg = <0x100>; clock-frequency = <1000000000>; + cci-control-port = <&cci_control0>; }; cpu5: cpu@101 { @@ -93,6 +98,7 @@ compatible = "arm,cortex-a7"; reg = <0x101>; clock-frequency = <1000000000>; + cci-control-port = <&cci_control0>; }; cpu6: cpu@102 { @@ -100,6 +106,7 @@ compatible = "arm,cortex-a7"; reg = <0x102>; clock-frequency = <1000000000>; + cci-control-port = <&cci_control0>; }; cpu7: cpu@103 { @@ -107,6 +114,44 @@ compatible = "arm,cortex-a7"; reg = <0x103>; clock-frequency = <1000000000>; + cci-control-port = <&cci_control0>; + }; + }; + + cci@10d20000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x10d20000 0x1000>; + ranges = <0x0 0x10d20000 0x6000>; + + cci_control0: slave-if@4000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x4000 0x1000>; + }; + cci_control1: slave-if@5000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x5000 0x1000>; + }; + }; + + sysram@02020000 { + compatible = "mmio-sram"; + reg = <0x02020000 0x54000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x02020000 0x54000>; + + smp-sysram@0 { + compatible = "samsung,exynos4210-sysram"; + reg = <0x0 0x1000>; + }; + + smp-sysram@53000 { + compatible = "samsung,exynos4210-sysram-ns"; + reg = <0x53000 0x1000>; }; }; @@ -125,7 +170,7 @@ clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in"; }; - codec@11000000 { + mfc: codec@11000000 { compatible = "samsung,mfc-v7"; reg = <0x11000000 0x10000>; interrupts = <0 96 0>; @@ -169,7 +214,7 @@ status = "disabled"; }; - mct@101C0000 { + mct: mct@101C0000 { compatible = "samsung,exynos4210-mct"; reg = <0x101C0000 0x800>; interrupt-controller; @@ -270,7 +315,7 @@ interrupts = <0 47 0>; }; - rtc@101E0000 { + rtc: rtc@101E0000 { clocks = <&clock CLK_RTC>; clock-names = "rtc"; status = "disabled"; @@ -430,22 +475,22 @@ status = "disabled"; }; - serial@12C00000 { + uart_0: serial@12C00000 { clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; clock-names = "uart", "clk_uart_baud0"; }; - serial@12C10000 { + uart_1: serial@12C10000 { clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>; clock-names = "uart", "clk_uart_baud0"; }; - serial@12C20000 { + uart_2: serial@12C20000 { clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; - serial@12C30000 { + uart_3: serial@12C30000 { clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>; clock-names = "uart", "clk_uart_baud0"; }; @@ -465,14 +510,14 @@ #phy-cells = <0>; }; - dp-controller@145B0000 { + dp: dp-controller@145B0000 { clocks = <&clock CLK_DP1>; clock-names = "dp"; phys = <&dp_phy>; phy-names = "dp"; }; - fimd@14400000 { + fimd: fimd@14400000 { samsung,power-domain = <&disp_pd>; clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>; clock-names = "sclk_fimd", "fimd"; @@ -549,7 +594,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c4_hs_bus>; - clocks = <&clock CLK_I2C4>; + clocks = <&clock CLK_USI0>; clock-names = "hsi2c"; status = "disabled"; }; @@ -562,7 +607,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c5_hs_bus>; - clocks = <&clock CLK_I2C5>; + clocks = <&clock CLK_USI1>; clock-names = "hsi2c"; status = "disabled"; }; @@ -575,7 +620,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c6_hs_bus>; - clocks = <&clock CLK_I2C6>; + clocks = <&clock CLK_USI2>; clock-names = "hsi2c"; status = "disabled"; }; @@ -588,7 +633,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c7_hs_bus>; - clocks = <&clock CLK_I2C7>; + clocks = <&clock CLK_USI3>; clock-names = "hsi2c"; status = "disabled"; }; @@ -601,7 +646,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c8_hs_bus>; - clocks = <&clock CLK_I2C8>; + clocks = <&clock CLK_USI4>; clock-names = "hsi2c"; status = "disabled"; }; @@ -614,7 +659,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c9_hs_bus>; - clocks = <&clock CLK_I2C9>; + clocks = <&clock CLK_USI5>; clock-names = "hsi2c"; status = "disabled"; }; @@ -627,12 +672,12 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c10_hs_bus>; - clocks = <&clock CLK_I2C10>; + clocks = <&clock CLK_USI6>; clock-names = "hsi2c"; status = "disabled"; }; - hdmi@14530000 { + hdmi: hdmi@14530000 { compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x70000>; interrupts = <0 95 0>; @@ -644,7 +689,7 @@ status = "disabled"; }; - mixer@14450000 { + mixer: mixer@14450000 { compatible = "samsung,exynos5420-mixer"; reg = <0x14450000 0x10000>; interrupts = <0 94 0>; @@ -715,7 +760,7 @@ clock-names = "tmu_apbif", "tmu_triminfo_apbif"; }; - watchdog@101D0000 { + watchdog: watchdog@101D0000 { compatible = "samsung,exynos5420-wdt"; reg = <0x101D0000 0x100>; interrupts = <0 42 0>; @@ -724,7 +769,7 @@ samsung,syscon-phandle = <&pmu_system_controller>; }; - sss@10830000 { + sss: sss@10830000 { compatible = "samsung,exynos4210-secss"; reg = <0x10830000 0x10000>; interrupts = <0 112 0>; diff --git a/arch/arm/boot/dts/s3c2416-smdk2416.dts b/arch/arm/boot/dts/s3c2416-smdk2416.dts index 59594cf15998..ea92fd69529a 100644 --- a/arch/arm/boot/dts/s3c2416-smdk2416.dts +++ b/arch/arm/boot/dts/s3c2416-smdk2416.dts @@ -19,6 +19,19 @@ reg = <0x30000000 0x4000000>; }; + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + + xti: xti { + compatible = "fixed-clock"; + clock-frequency = <12000000>; + clock-output-names = "xti"; + #clock-cells = <0>; + }; + }; + serial@50000000 { status = "okay"; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/s3c2416.dtsi b/arch/arm/boot/dts/s3c2416.dtsi index e6555bdd81b8..955e4a4f8c31 100644 --- a/arch/arm/boot/dts/s3c2416.dtsi +++ b/arch/arm/boot/dts/s3c2416.dtsi @@ -8,6 +8,7 @@ * published by the Free Software Foundation. */ +#include <dt-bindings/clock/s3c2443.h> #include "s3c24xx.dtsi" #include "s3c2416-pinctrl.dtsi" @@ -28,26 +29,53 @@ compatible = "samsung,s3c2416-irq"; }; + clocks: clock-controller@0x4c000000 { + compatible = "samsung,s3c2416-clock"; + reg = <0x4c000000 0x40>; + #clock-cells = <1>; + }; + pinctrl@56000000 { compatible = "samsung,s3c2416-pinctrl"; }; + timer@51000000 { + clocks = <&clocks PCLK_PWM>; + clock-names = "timers"; + }; + serial@50000000 { compatible = "samsung,s3c2440-uart"; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; }; serial@50004000 { compatible = "samsung,s3c2440-uart"; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>, + <&clocks SCLK_UART>; }; serial@50008000 { compatible = "samsung,s3c2440-uart"; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART2>, <&clocks PCLK_UART2>, + <&clocks SCLK_UART>; }; serial@5000C000 { compatible = "samsung,s3c2440-uart"; reg = <0x5000C000 0x4000>; interrupts = <1 18 24 4>, <1 18 25 4>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART3>, <&clocks PCLK_UART3>, + <&clocks SCLK_UART>; status = "disabled"; }; @@ -55,6 +83,10 @@ compatible = "samsung,s3c6410-sdhci"; reg = <0x4AC00000 0x100>; interrupts = <0 0 21 3>; + clock-names = "hsmmc", "mmc_busclk.0", + "mmc_busclk.2"; + clocks = <&clocks HCLK_HSMMC0>, <&clocks HCLK_HSMMC0>, + <&clocks MUX_HSMMC0>; status = "disabled"; }; @@ -62,18 +94,28 @@ compatible = "samsung,s3c6410-sdhci"; reg = <0x4A800000 0x100>; interrupts = <0 0 20 3>; + clock-names = "hsmmc", "mmc_busclk.0", + "mmc_busclk.2"; + clocks = <&clocks HCLK_HSMMC1>, <&clocks HCLK_HSMMC1>, + <&clocks MUX_HSMMC1>; status = "disabled"; }; watchdog@53000000 { interrupts = <1 9 27 3>; + clocks = <&clocks PCLK_WDT>; + clock-names = "watchdog"; }; rtc@57000000 { compatible = "samsung,s3c2416-rtc"; + clocks = <&clocks PCLK_RTC>; + clock-names = "rtc"; }; i2c@54000000 { compatible = "samsung,s3c2440-i2c"; + clocks = <&clocks PCLK_I2C0>; + clock-names = "i2c"; }; }; diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig index fc8bf18e222d..1602abce6ec0 100644 --- a/arch/arm/mach-exynos/Kconfig +++ b/arch/arm/mach-exynos/Kconfig @@ -110,4 +110,12 @@ config SOC_EXYNOS5440 endmenu +config EXYNOS5420_MCPM + bool "Exynos5420 Multi-Cluster PM support" + depends on MCPM && SOC_EXYNOS5420 + select ARM_CCI + help + This is needed to provide CPU and cluster power management + on Exynos5420 implementing big.LITTLE. + endif diff --git a/arch/arm/mach-exynos/Makefile b/arch/arm/mach-exynos/Makefile index a656dbe3b78c..3705048f744a 100644 --- a/arch/arm/mach-exynos/Makefile +++ b/arch/arm/mach-exynos/Makefile @@ -16,7 +16,6 @@ obj-$(CONFIG_ARCH_EXYNOS) += exynos.o obj-$(CONFIG_PM_SLEEP) += pm.o sleep.o obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o -obj-$(CONFIG_CPU_IDLE) += cpuidle.o obj-$(CONFIG_ARCH_EXYNOS) += pmu.o @@ -29,3 +28,5 @@ obj-$(CONFIG_ARCH_EXYNOS) += firmware.o plus_sec := $(call as-instr,.arch_extension sec,+sec) AFLAGS_exynos-smc.o :=-Wa,-march=armv7-a$(plus_sec) + +obj-$(CONFIG_EXYNOS5420_MCPM) += mcpm-exynos.o diff --git a/arch/arm/mach-exynos/common.h b/arch/arm/mach-exynos/common.h index 9ef3f83efaff..5848d3cc29e9 100644 --- a/arch/arm/mach-exynos/common.h +++ b/arch/arm/mach-exynos/common.h @@ -18,6 +18,8 @@ void mct_init(void __iomem *base, int irq_g0, int irq_l0, int irq_l1); struct map_desc; +extern void __iomem *sysram_ns_base_addr; +extern void __iomem *sysram_base_addr; void exynos_init_io(void); void exynos_restart(enum reboot_mode mode, const char *cmd); void exynos_cpuidle_init(void); @@ -62,5 +64,12 @@ struct exynos_pmu_conf { }; extern void exynos_sys_powerdown_conf(enum sys_powerdown mode); +extern void exynos_cpu_power_down(int cpu); +extern void exynos_cpu_power_up(int cpu); +extern int exynos_cpu_power_state(int cpu); +extern void exynos_cluster_power_down(int cluster); +extern void exynos_cluster_power_up(int cluster); +extern int exynos_cluster_power_state(int cluster); +extern void exynos_enter_aftr(void); #endif /* __ARCH_ARM_MACH_EXYNOS_COMMON_H */ diff --git a/arch/arm/mach-exynos/cpuidle.c b/arch/arm/mach-exynos/cpuidle.c deleted file mode 100644 index c57cae0e8779..000000000000 --- a/arch/arm/mach-exynos/cpuidle.c +++ /dev/null @@ -1,256 +0,0 @@ -/* linux/arch/arm/mach-exynos4/cpuidle.c - * - * Copyright (c) 2011 Samsung Electronics Co., Ltd. - * http://www.samsung.com - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. -*/ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/cpuidle.h> -#include <linux/cpu_pm.h> -#include <linux/io.h> -#include <linux/export.h> -#include <linux/module.h> -#include <linux/time.h> -#include <linux/platform_device.h> - -#include <asm/proc-fns.h> -#include <asm/smp_scu.h> -#include <asm/suspend.h> -#include <asm/unified.h> -#include <asm/cpuidle.h> - -#include <plat/cpu.h> -#include <plat/pm.h> - -#include <mach/map.h> - -#include "common.h" -#include "regs-pmu.h" - -#define REG_DIRECTGO_ADDR (samsung_rev() == EXYNOS4210_REV_1_1 ? \ - S5P_INFORM7 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \ - (S5P_VA_SYSRAM + 0x24) : S5P_INFORM0)) -#define REG_DIRECTGO_FLAG (samsung_rev() == EXYNOS4210_REV_1_1 ? \ - S5P_INFORM6 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \ - (S5P_VA_SYSRAM + 0x20) : S5P_INFORM1)) - -#define S5P_CHECK_AFTR 0xFCBA0D10 - -#define EXYNOS5_PWR_CTRL1 (S5P_VA_CMU + 0x01020) -#define EXYNOS5_PWR_CTRL2 (S5P_VA_CMU + 0x01024) - -#define PWR_CTRL1_CORE2_DOWN_RATIO (7 << 28) -#define PWR_CTRL1_CORE1_DOWN_RATIO (7 << 16) -#define PWR_CTRL1_DIV2_DOWN_EN (1 << 9) -#define PWR_CTRL1_DIV1_DOWN_EN (1 << 8) -#define PWR_CTRL1_USE_CORE1_WFE (1 << 5) -#define PWR_CTRL1_USE_CORE0_WFE (1 << 4) -#define PWR_CTRL1_USE_CORE1_WFI (1 << 1) -#define PWR_CTRL1_USE_CORE0_WFI (1 << 0) - -#define PWR_CTRL2_DIV2_UP_EN (1 << 25) -#define PWR_CTRL2_DIV1_UP_EN (1 << 24) -#define PWR_CTRL2_DUR_STANDBY2_VAL (1 << 16) -#define PWR_CTRL2_DUR_STANDBY1_VAL (1 << 8) -#define PWR_CTRL2_CORE2_UP_RATIO (1 << 4) -#define PWR_CTRL2_CORE1_UP_RATIO (1 << 0) - -static int exynos4_enter_lowpower(struct cpuidle_device *dev, - struct cpuidle_driver *drv, - int index); - -static DEFINE_PER_CPU(struct cpuidle_device, exynos4_cpuidle_device); - -static struct cpuidle_driver exynos4_idle_driver = { - .name = "exynos4_idle", - .owner = THIS_MODULE, - .states = { - [0] = ARM_CPUIDLE_WFI_STATE, - [1] = { - .enter = exynos4_enter_lowpower, - .exit_latency = 300, - .target_residency = 100000, - .flags = CPUIDLE_FLAG_TIME_VALID, - .name = "C1", - .desc = "ARM power down", - }, - }, - .state_count = 2, - .safe_state_index = 0, -}; - -/* Ext-GIC nIRQ/nFIQ is the only wakeup source in AFTR */ -static void exynos4_set_wakeupmask(void) -{ - __raw_writel(0x0000ff3e, S5P_WAKEUP_MASK); -} - -static unsigned int g_pwr_ctrl, g_diag_reg; - -static void save_cpu_arch_register(void) -{ - /*read power control register*/ - asm("mrc p15, 0, %0, c15, c0, 0" : "=r"(g_pwr_ctrl) : : "cc"); - /*read diagnostic register*/ - asm("mrc p15, 0, %0, c15, c0, 1" : "=r"(g_diag_reg) : : "cc"); - return; -} - -static void restore_cpu_arch_register(void) -{ - /*write power control register*/ - asm("mcr p15, 0, %0, c15, c0, 0" : : "r"(g_pwr_ctrl) : "cc"); - /*write diagnostic register*/ - asm("mcr p15, 0, %0, c15, c0, 1" : : "r"(g_diag_reg) : "cc"); - return; -} - -static int idle_finisher(unsigned long flags) -{ - cpu_do_idle(); - return 1; -} - -static int exynos4_enter_core0_aftr(struct cpuidle_device *dev, - struct cpuidle_driver *drv, - int index) -{ - unsigned long tmp; - - exynos4_set_wakeupmask(); - - /* Set value of power down register for aftr mode */ - exynos_sys_powerdown_conf(SYS_AFTR); - - __raw_writel(virt_to_phys(exynos_cpu_resume), REG_DIRECTGO_ADDR); - __raw_writel(S5P_CHECK_AFTR, REG_DIRECTGO_FLAG); - - save_cpu_arch_register(); - - /* Setting Central Sequence Register for power down mode */ - tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION); - tmp &= ~S5P_CENTRAL_LOWPWR_CFG; - __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION); - - cpu_pm_enter(); - cpu_suspend(0, idle_finisher); - -#ifdef CONFIG_SMP - if (!soc_is_exynos5250()) - scu_enable(S5P_VA_SCU); -#endif - cpu_pm_exit(); - - restore_cpu_arch_register(); - - /* - * If PMU failed while entering sleep mode, WFI will be - * ignored by PMU and then exiting cpu_do_idle(). - * S5P_CENTRAL_LOWPWR_CFG bit will not be set automatically - * in this situation. - */ - tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION); - if (!(tmp & S5P_CENTRAL_LOWPWR_CFG)) { - tmp |= S5P_CENTRAL_LOWPWR_CFG; - __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION); - } - - /* Clear wakeup state register */ - __raw_writel(0x0, S5P_WAKEUP_STAT); - - return index; -} - -static int exynos4_enter_lowpower(struct cpuidle_device *dev, - struct cpuidle_driver *drv, - int index) -{ - int new_index = index; - - /* AFTR can only be entered when cores other than CPU0 are offline */ - if (num_online_cpus() > 1 || dev->cpu != 0) - new_index = drv->safe_state_index; - - if (new_index == 0) - return arm_cpuidle_simple_enter(dev, drv, new_index); - else - return exynos4_enter_core0_aftr(dev, drv, new_index); -} - -static void __init exynos5_core_down_clk(void) -{ - unsigned int tmp; - - /* - * Enable arm clock down (in idle) and set arm divider - * ratios in WFI/WFE state. - */ - tmp = PWR_CTRL1_CORE2_DOWN_RATIO | \ - PWR_CTRL1_CORE1_DOWN_RATIO | \ - PWR_CTRL1_DIV2_DOWN_EN | \ - PWR_CTRL1_DIV1_DOWN_EN | \ - PWR_CTRL1_USE_CORE1_WFE | \ - PWR_CTRL1_USE_CORE0_WFE | \ - PWR_CTRL1_USE_CORE1_WFI | \ - PWR_CTRL1_USE_CORE0_WFI; - __raw_writel(tmp, EXYNOS5_PWR_CTRL1); - - /* - * Enable arm clock up (on exiting idle). Set arm divider - * ratios when not in idle along with the standby duration - * ratios. - */ - tmp = PWR_CTRL2_DIV2_UP_EN | \ - PWR_CTRL2_DIV1_UP_EN | \ - PWR_CTRL2_DUR_STANDBY2_VAL | \ - PWR_CTRL2_DUR_STANDBY1_VAL | \ - PWR_CTRL2_CORE2_UP_RATIO | \ - PWR_CTRL2_CORE1_UP_RATIO; - __raw_writel(tmp, EXYNOS5_PWR_CTRL2); -} - -static int exynos_cpuidle_probe(struct platform_device *pdev) -{ - int cpu_id, ret; - struct cpuidle_device *device; - - if (soc_is_exynos5250()) - exynos5_core_down_clk(); - - if (soc_is_exynos5440()) - exynos4_idle_driver.state_count = 1; - - ret = cpuidle_register_driver(&exynos4_idle_driver); - if (ret) { - dev_err(&pdev->dev, "failed to register cpuidle driver\n"); - return ret; - } - - for_each_online_cpu(cpu_id) { - device = &per_cpu(exynos4_cpuidle_device, cpu_id); - device->cpu = cpu_id; - - ret = cpuidle_register_device(device); - if (ret) { - dev_err(&pdev->dev, "failed to register cpuidle device\n"); - return ret; - } - } - - return 0; -} - -static struct platform_driver exynos_cpuidle_driver = { - .probe = exynos_cpuidle_probe, - .driver = { - .name = "exynos_cpuidle", - .owner = THIS_MODULE, - }, -}; - -module_platform_driver(exynos_cpuidle_driver); diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c index b32a907d021d..7d9d8762b56e 100644 --- a/arch/arm/mach-exynos/exynos.c +++ b/arch/arm/mach-exynos/exynos.c @@ -114,51 +114,6 @@ static struct map_desc exynos4_iodesc[] __initdata = { }, }; -static struct map_desc exynos4_iodesc0[] __initdata = { - { - .virtual = (unsigned long)S5P_VA_SYSRAM, - .pfn = __phys_to_pfn(EXYNOS4_PA_SYSRAM0), - .length = SZ_4K, - .type = MT_DEVICE, - }, -}; - -static struct map_desc exynos4_iodesc1[] __initdata = { - { - .virtual = (unsigned long)S5P_VA_SYSRAM, - .pfn = __phys_to_pfn(EXYNOS4_PA_SYSRAM1), - .length = SZ_4K, - .type = MT_DEVICE, - }, -}; - -static struct map_desc exynos4210_iodesc[] __initdata = { - { - .virtual = (unsigned long)S5P_VA_SYSRAM_NS, - .pfn = __phys_to_pfn(EXYNOS4210_PA_SYSRAM_NS), - .length = SZ_4K, - .type = MT_DEVICE, - }, -}; - -static struct map_desc exynos4x12_iodesc[] __initdata = { - { - .virtual = (unsigned long)S5P_VA_SYSRAM_NS, - .pfn = __phys_to_pfn(EXYNOS4x12_PA_SYSRAM_NS), - .length = SZ_4K, - .type = MT_DEVICE, - }, -}; - -static struct map_desc exynos5250_iodesc[] __initdata = { - { - .virtual = (unsigned long)S5P_VA_SYSRAM_NS, - .pfn = __phys_to_pfn(EXYNOS5250_PA_SYSRAM_NS), - .length = SZ_4K, - .type = MT_DEVICE, - }, -}; - static struct map_desc exynos5_iodesc[] __initdata = { { .virtual = (unsigned long)S3C_VA_SYS, @@ -181,11 +136,6 @@ static struct map_desc exynos5_iodesc[] __initdata = { .length = SZ_4K, .type = MT_DEVICE, }, { - .virtual = (unsigned long)S5P_VA_SYSRAM, - .pfn = __phys_to_pfn(EXYNOS5_PA_SYSRAM), - .length = SZ_4K, - .type = MT_DEVICE, - }, { .virtual = (unsigned long)S5P_VA_CMU, .pfn = __phys_to_pfn(EXYNOS5_PA_CMU), .length = 144 * SZ_1K, @@ -221,12 +171,16 @@ void exynos_restart(enum reboot_mode mode, const char *cmd) } static struct platform_device exynos_cpuidle = { - .name = "exynos_cpuidle", - .id = -1, + .name = "exynos_cpuidle", + .dev.platform_data = exynos_enter_aftr, + .id = -1, }; void __init exynos_cpuidle_init(void) { + if (soc_is_exynos5440()) + return; + platform_device_register(&exynos_cpuidle); } @@ -280,20 +234,6 @@ static void __init exynos_map_io(void) if (soc_is_exynos5()) iotable_init(exynos5_iodesc, ARRAY_SIZE(exynos5_iodesc)); - - if (soc_is_exynos4210()) { - if (samsung_rev() == EXYNOS4210_REV_0) - iotable_init(exynos4_iodesc0, - ARRAY_SIZE(exynos4_iodesc0)); - else - iotable_init(exynos4_iodesc1, - ARRAY_SIZE(exynos4_iodesc1)); - iotable_init(exynos4210_iodesc, ARRAY_SIZE(exynos4210_iodesc)); - } - if (soc_is_exynos4212() || soc_is_exynos4412()) - iotable_init(exynos4x12_iodesc, ARRAY_SIZE(exynos4x12_iodesc)); - if (soc_is_exynos5250()) - iotable_init(exynos5250_iodesc, ARRAY_SIZE(exynos5250_iodesc)); } void __init exynos_init_io(void) diff --git a/arch/arm/mach-exynos/firmware.c b/arch/arm/mach-exynos/firmware.c index 932129ef26c6..483dfcd69065 100644 --- a/arch/arm/mach-exynos/firmware.c +++ b/arch/arm/mach-exynos/firmware.c @@ -18,6 +18,7 @@ #include <mach/map.h> +#include "common.h" #include "smc.h" static int exynos_do_idle(void) @@ -34,7 +35,12 @@ static int exynos_cpu_boot(int cpu) static int exynos_set_cpu_boot_addr(int cpu, unsigned long boot_addr) { - void __iomem *boot_reg = S5P_VA_SYSRAM_NS + 0x1c + 4*cpu; + void __iomem *boot_reg; + + if (!sysram_ns_base_addr) + return -ENODEV; + + boot_reg = sysram_ns_base_addr + 0x1c + 4*cpu; __raw_writel(boot_addr, boot_reg); return 0; diff --git a/arch/arm/mach-exynos/hotplug.c b/arch/arm/mach-exynos/hotplug.c index 5eead530c6f8..609c99ca59c4 100644 --- a/arch/arm/mach-exynos/hotplug.c +++ b/arch/arm/mach-exynos/hotplug.c @@ -96,7 +96,7 @@ static inline void platform_do_lowpower(unsigned int cpu, int *spurious) /* make cpu1 to be turned off at next WFI command */ if (cpu == 1) - __raw_writel(0, S5P_ARM_CORE1_CONFIGURATION); + exynos_cpu_power_down(cpu); /* * here's the WFI diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h index 7b046b59d9ec..548269a60634 100644 --- a/arch/arm/mach-exynos/include/mach/map.h +++ b/arch/arm/mach-exynos/include/mach/map.h @@ -23,13 +23,6 @@ #include <plat/map-s5p.h> -#define EXYNOS4_PA_SYSRAM0 0x02025000 -#define EXYNOS4_PA_SYSRAM1 0x02020000 -#define EXYNOS5_PA_SYSRAM 0x02020000 -#define EXYNOS4210_PA_SYSRAM_NS 0x0203F000 -#define EXYNOS4x12_PA_SYSRAM_NS 0x0204F000 -#define EXYNOS5250_PA_SYSRAM_NS 0x0204F000 - #define EXYNOS_PA_CHIPID 0x10000000 #define EXYNOS4_PA_SYSCON 0x10010000 diff --git a/arch/arm/mach-exynos/mcpm-exynos.c b/arch/arm/mach-exynos/mcpm-exynos.c new file mode 100644 index 000000000000..1ac618ce440b --- /dev/null +++ b/arch/arm/mach-exynos/mcpm-exynos.c @@ -0,0 +1,351 @@ +/* + * Copyright (c) 2014 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * arch/arm/mach-exynos/mcpm-exynos.c + * + * Based on arch/arm/mach-vexpress/dcscb.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/arm-cci.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/of_address.h> + +#include <asm/cputype.h> +#include <asm/cp15.h> +#include <asm/mcpm.h> + +#include "regs-pmu.h" +#include "common.h" + +#define EXYNOS5420_CPUS_PER_CLUSTER 4 +#define EXYNOS5420_NR_CLUSTERS 2 +#define MCPM_BOOT_ADDR_OFFSET 0x1c + +/* + * The common v7_exit_coherency_flush API could not be used because of the + * Erratum 799270 workaround. This macro is the same as the common one (in + * arch/arm/include/asm/cacheflush.h) except for the erratum handling. + */ +#define exynos_v7_exit_coherency_flush(level) \ + asm volatile( \ + "stmfd sp!, {fp, ip}\n\t"\ + "mrc p15, 0, r0, c1, c0, 0 @ get SCTLR\n\t" \ + "bic r0, r0, #"__stringify(CR_C)"\n\t" \ + "mcr p15, 0, r0, c1, c0, 0 @ set SCTLR\n\t" \ + "isb\n\t"\ + "bl v7_flush_dcache_"__stringify(level)"\n\t" \ + "clrex\n\t"\ + "mrc p15, 0, r0, c1, c0, 1 @ get ACTLR\n\t" \ + "bic r0, r0, #(1 << 6) @ disable local coherency\n\t" \ + /* Dummy Load of a device register to avoid Erratum 799270 */ \ + "ldr r4, [%0]\n\t" \ + "and r4, r4, #0\n\t" \ + "orr r0, r0, r4\n\t" \ + "mcr p15, 0, r0, c1, c0, 1 @ set ACTLR\n\t" \ + "isb\n\t" \ + "dsb\n\t" \ + "ldmfd sp!, {fp, ip}" \ + : \ + : "Ir" (S5P_INFORM0) \ + : "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", \ + "r9", "r10", "lr", "memory") + +/* + * We can't use regular spinlocks. In the switcher case, it is possible + * for an outbound CPU to call power_down() after its inbound counterpart + * is already live using the same logical CPU number which trips lockdep + * debugging. + */ +static arch_spinlock_t exynos_mcpm_lock = __ARCH_SPIN_LOCK_UNLOCKED; +static int +cpu_use_count[EXYNOS5420_CPUS_PER_CLUSTER][EXYNOS5420_NR_CLUSTERS]; + +#define exynos_cluster_usecnt(cluster) \ + (cpu_use_count[0][cluster] + \ + cpu_use_count[1][cluster] + \ + cpu_use_count[2][cluster] + \ + cpu_use_count[3][cluster]) + +#define exynos_cluster_unused(cluster) !exynos_cluster_usecnt(cluster) + +static int exynos_cluster_power_control(unsigned int cluster, int enable) +{ + unsigned int tries = 100; + unsigned int val; + + if (enable) { + exynos_cluster_power_up(cluster); + val = S5P_CORE_LOCAL_PWR_EN; + } else { + exynos_cluster_power_down(cluster); + val = 0; + } + + /* Wait until cluster power control is applied */ + while (tries--) { + if (exynos_cluster_power_state(cluster) == val) + return 0; + + cpu_relax(); + } + pr_debug("timed out waiting for cluster %u to power %s\n", cluster, + enable ? "on" : "off"); + + return -ETIMEDOUT; +} + +static int exynos_power_up(unsigned int cpu, unsigned int cluster) +{ + unsigned int cpunr = cpu + (cluster * EXYNOS5420_CPUS_PER_CLUSTER); + int err = 0; + + pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); + if (cpu >= EXYNOS5420_CPUS_PER_CLUSTER || + cluster >= EXYNOS5420_NR_CLUSTERS) + return -EINVAL; + + /* + * Since this is called with IRQs enabled, and no arch_spin_lock_irq + * variant exists, we need to disable IRQs manually here. + */ + local_irq_disable(); + arch_spin_lock(&exynos_mcpm_lock); + + cpu_use_count[cpu][cluster]++; + if (cpu_use_count[cpu][cluster] == 1) { + bool was_cluster_down = + (exynos_cluster_usecnt(cluster) == 1); + + /* + * Turn on the cluster (L2/COMMON) and then power on the + * cores. + */ + if (was_cluster_down) + err = exynos_cluster_power_control(cluster, 1); + + if (!err) + exynos_cpu_power_up(cpunr); + else + exynos_cluster_power_control(cluster, 0); + } else if (cpu_use_count[cpu][cluster] != 2) { + /* + * The only possible values are: + * 0 = CPU down + * 1 = CPU (still) up + * 2 = CPU requested to be up before it had a chance + * to actually make itself down. + * Any other value is a bug. + */ + BUG(); + } + + arch_spin_unlock(&exynos_mcpm_lock); + local_irq_enable(); + + return err; +} + +/* + * NOTE: This function requires the stack data to be visible through power down + * and can only be executed on processors like A15 and A7 that hit the cache + * with the C bit clear in the SCTLR register. + */ +static void exynos_power_down(void) +{ + unsigned int mpidr, cpu, cluster; + bool last_man = false, skip_wfi = false; + unsigned int cpunr; + + mpidr = read_cpuid_mpidr(); + cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); + cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); + cpunr = cpu + (cluster * EXYNOS5420_CPUS_PER_CLUSTER); + + pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); + BUG_ON(cpu >= EXYNOS5420_CPUS_PER_CLUSTER || + cluster >= EXYNOS5420_NR_CLUSTERS); + + __mcpm_cpu_going_down(cpu, cluster); + + arch_spin_lock(&exynos_mcpm_lock); + BUG_ON(__mcpm_cluster_state(cluster) != CLUSTER_UP); + cpu_use_count[cpu][cluster]--; + if (cpu_use_count[cpu][cluster] == 0) { + exynos_cpu_power_down(cpunr); + + if (exynos_cluster_unused(cluster)) + /* TODO: Turn off the cluster here to save power. */ + last_man = true; + } else if (cpu_use_count[cpu][cluster] == 1) { + /* + * A power_up request went ahead of us. + * Even if we do not want to shut this CPU down, + * the caller expects a certain state as if the WFI + * was aborted. So let's continue with cache cleaning. + */ + skip_wfi = true; + } else { + BUG(); + } + + if (last_man && __mcpm_outbound_enter_critical(cpu, cluster)) { + arch_spin_unlock(&exynos_mcpm_lock); + + if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A15) { + /* + * On the Cortex-A15 we need to disable + * L2 prefetching before flushing the cache. + */ + asm volatile( + "mcr p15, 1, %0, c15, c0, 3\n\t" + "isb\n\t" + "dsb" + : : "r" (0x400)); + } + + /* Flush all cache levels for this cluster. */ + exynos_v7_exit_coherency_flush(all); + + /* + * Disable cluster-level coherency by masking + * incoming snoops and DVM messages: + */ + cci_disable_port_by_cpu(mpidr); + + __mcpm_outbound_leave_critical(cluster, CLUSTER_DOWN); + } else { + arch_spin_unlock(&exynos_mcpm_lock); + + /* Disable and flush the local CPU cache. */ + exynos_v7_exit_coherency_flush(louis); + } + + __mcpm_cpu_down(cpu, cluster); + + /* Now we are prepared for power-down, do it: */ + if (!skip_wfi) + wfi(); + + /* Not dead at this point? Let our caller cope. */ +} + +static int exynos_power_down_finish(unsigned int cpu, unsigned int cluster) +{ + unsigned int tries = 100; + unsigned int cpunr = cpu + (cluster * EXYNOS5420_CPUS_PER_CLUSTER); + + pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); + BUG_ON(cpu >= EXYNOS5420_CPUS_PER_CLUSTER || + cluster >= EXYNOS5420_NR_CLUSTERS); + + /* Wait for the core state to be OFF */ + while (tries--) { + if (ACCESS_ONCE(cpu_use_count[cpu][cluster]) == 0) { + if ((exynos_cpu_power_state(cpunr) == 0)) + return 0; /* success: the CPU is halted */ + } + + /* Otherwise, wait and retry: */ + msleep(1); + } + + return -ETIMEDOUT; /* timeout */ +} + +static const struct mcpm_platform_ops exynos_power_ops = { + .power_up = exynos_power_up, + .power_down = exynos_power_down, + .power_down_finish = exynos_power_down_finish, +}; + +static void __init exynos_mcpm_usage_count_init(void) +{ + unsigned int mpidr, cpu, cluster; + + mpidr = read_cpuid_mpidr(); + cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0); + cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1); + + pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster); + BUG_ON(cpu >= EXYNOS5420_CPUS_PER_CLUSTER || + cluster >= EXYNOS5420_NR_CLUSTERS); + + cpu_use_count[cpu][cluster] = 1; +} + +/* + * Enable cluster-level coherency, in preparation for turning on the MMU. + */ +static void __naked exynos_pm_power_up_setup(unsigned int affinity_level) +{ + asm volatile ("\n" + "cmp r0, #1\n" + "bxne lr\n" + "b cci_enable_port_for_self"); +} + +static int __init exynos_mcpm_init(void) +{ + struct device_node *node; + void __iomem *ns_sram_base_addr; + int ret; + + node = of_find_compatible_node(NULL, NULL, "samsung,exynos5420"); + if (!node) + return -ENODEV; + of_node_put(node); + + if (!cci_probed()) + return -ENODEV; + + node = of_find_compatible_node(NULL, NULL, + "samsung,exynos4210-sysram-ns"); + if (!node) + return -ENODEV; + + ns_sram_base_addr = of_iomap(node, 0); + of_node_put(node); + if (!ns_sram_base_addr) { + pr_err("failed to map non-secure iRAM base address\n"); + return -ENOMEM; + } + + /* + * To increase the stability of KFC reset we need to program + * the PMU SPARE3 register + */ + __raw_writel(EXYNOS5420_SWRESET_KFC_SEL, S5P_PMU_SPARE3); + + exynos_mcpm_usage_count_init(); + + ret = mcpm_platform_register(&exynos_power_ops); + if (!ret) + ret = mcpm_sync_init(exynos_pm_power_up_setup); + if (ret) { + iounmap(ns_sram_base_addr); + return ret; + } + + mcpm_smp_set_ops(); + + pr_info("Exynos MCPM support installed\n"); + + /* + * Future entries into the kernel can now go + * through the cluster entry vectors. + */ + __raw_writel(virt_to_phys(mcpm_entry_point), + ns_sram_base_addr + MCPM_BOOT_ADDR_OFFSET); + + iounmap(ns_sram_base_addr); + + return ret; +} + +early_initcall(exynos_mcpm_init); diff --git a/arch/arm/mach-exynos/platsmp.c b/arch/arm/mach-exynos/platsmp.c index 03e5e9f94705..9e5e230575dd 100644 --- a/arch/arm/mach-exynos/platsmp.c +++ b/arch/arm/mach-exynos/platsmp.c @@ -20,6 +20,7 @@ #include <linux/jiffies.h> #include <linux/smp.h> #include <linux/io.h> +#include <linux/of_address.h> #include <asm/cacheflush.h> #include <asm/smp_plat.h> @@ -33,11 +34,33 @@ extern void exynos4_secondary_startup(void); +void __iomem *sysram_base_addr; +void __iomem *sysram_ns_base_addr; + +static void __init exynos_smp_prepare_sysram(void) +{ + struct device_node *node; + + for_each_compatible_node(node, NULL, "samsung,exynos4210-sysram") { + if (!of_device_is_available(node)) + continue; + sysram_base_addr = of_iomap(node, 0); + break; + } + + for_each_compatible_node(node, NULL, "samsung,exynos4210-sysram-ns") { + if (!of_device_is_available(node)) + continue; + sysram_ns_base_addr = of_iomap(node, 0); + break; + } +} + static inline void __iomem *cpu_boot_reg_base(void) { if (soc_is_exynos4210() && samsung_rev() == EXYNOS4210_REV_1_1) return S5P_INFORM5; - return S5P_VA_SYSRAM; + return sysram_base_addr; } static inline void __iomem *cpu_boot_reg(int cpu) @@ -45,6 +68,8 @@ static inline void __iomem *cpu_boot_reg(int cpu) void __iomem *boot_reg; boot_reg = cpu_boot_reg_base(); + if (!boot_reg) + return ERR_PTR(-ENODEV); if (soc_is_exynos4412()) boot_reg += 4*cpu; else if (soc_is_exynos5420()) @@ -90,6 +115,7 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle) { unsigned long timeout; unsigned long phys_cpu = cpu_logical_map(cpu); + int ret = -ENOSYS; /* * Set synchronisation state between this boot processor @@ -107,15 +133,12 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle) */ write_pen_release(phys_cpu); - if (!(__raw_readl(S5P_ARM_CORE1_STATUS) & S5P_CORE_LOCAL_PWR_EN)) { - __raw_writel(S5P_CORE_LOCAL_PWR_EN, - S5P_ARM_CORE1_CONFIGURATION); - + if (!exynos_cpu_power_state(cpu)) { + exynos_cpu_power_up(cpu); timeout = 10; /* wait max 10 ms until cpu1 is on */ - while ((__raw_readl(S5P_ARM_CORE1_STATUS) - & S5P_CORE_LOCAL_PWR_EN) != S5P_CORE_LOCAL_PWR_EN) { + while (exynos_cpu_power_state(cpu) != S5P_CORE_LOCAL_PWR_EN) { if (timeout-- == 0) break; @@ -146,8 +169,18 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle) * Try to set boot address using firmware first * and fall back to boot register if it fails. */ - if (call_firmware_op(set_cpu_boot_addr, phys_cpu, boot_addr)) + ret = call_firmware_op(set_cpu_boot_addr, phys_cpu, boot_addr); + if (ret && ret != -ENOSYS) + goto fail; + if (ret == -ENOSYS) { + void __iomem *boot_reg = cpu_boot_reg(phys_cpu); + + if (IS_ERR(boot_reg)) { + ret = PTR_ERR(boot_reg); + goto fail; + } __raw_writel(boot_addr, cpu_boot_reg(phys_cpu)); + } call_firmware_op(cpu_boot, phys_cpu); @@ -163,9 +196,10 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle) * now the secondary core is starting up let it run its * calibrations, then wait for it to finish */ +fail: spin_unlock(&boot_lock); - return pen_release != -1 ? -ENOSYS : 0; + return pen_release != -1 ? ret : 0; } /* @@ -205,6 +239,8 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus) if (read_cpuid_part_number() == ARM_CPU_PART_CORTEX_A9) scu_enable(scu_base_addr()); + exynos_smp_prepare_sysram(); + /* * Write the address of secondary startup into the * system-wide flags register. The boot monitor waits @@ -217,12 +253,21 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus) for (i = 1; i < max_cpus; ++i) { unsigned long phys_cpu; unsigned long boot_addr; + int ret; phys_cpu = cpu_logical_map(i); boot_addr = virt_to_phys(exynos4_secondary_startup); - if (call_firmware_op(set_cpu_boot_addr, phys_cpu, boot_addr)) + ret = call_firmware_op(set_cpu_boot_addr, phys_cpu, boot_addr); + if (ret && ret != -ENOSYS) + break; + if (ret == -ENOSYS) { + void __iomem *boot_reg = cpu_boot_reg(phys_cpu); + + if (IS_ERR(boot_reg)) + break; __raw_writel(boot_addr, cpu_boot_reg(phys_cpu)); + } } } diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c index 15af0ceb0a66..0d1a46e7b021 100644 --- a/arch/arm/mach-exynos/pm.c +++ b/arch/arm/mach-exynos/pm.c @@ -16,6 +16,7 @@ #include <linux/init.h> #include <linux/suspend.h> #include <linux/syscore_ops.h> +#include <linux/cpu_pm.h> #include <linux/io.h> #include <linux/irqchip/arm-gic.h> #include <linux/err.h> @@ -100,9 +101,141 @@ static int exynos_irq_set_wake(struct irq_data *data, unsigned int state) return -ENOENT; } +/** + * exynos_core_power_down : power down the specified cpu + * @cpu : the cpu to power down + * + * Power down the specified cpu. The sequence must be finished by a + * call to cpu_do_idle() + * + */ +void exynos_cpu_power_down(int cpu) +{ + __raw_writel(0, EXYNOS_ARM_CORE_CONFIGURATION(cpu)); +} + +/** + * exynos_cpu_power_up : power up the specified cpu + * @cpu : the cpu to power up + * + * Power up the specified cpu + */ +void exynos_cpu_power_up(int cpu) +{ + __raw_writel(S5P_CORE_LOCAL_PWR_EN, + EXYNOS_ARM_CORE_CONFIGURATION(cpu)); +} + +/** + * exynos_cpu_power_state : returns the power state of the cpu + * @cpu : the cpu to retrieve the power state from + * + */ +int exynos_cpu_power_state(int cpu) +{ + return (__raw_readl(EXYNOS_ARM_CORE_STATUS(cpu)) & + S5P_CORE_LOCAL_PWR_EN); +} + +/** + * exynos_cluster_power_down : power down the specified cluster + * @cluster : the cluster to power down + */ +void exynos_cluster_power_down(int cluster) +{ + __raw_writel(0, EXYNOS_COMMON_CONFIGURATION(cluster)); +} + +/** + * exynos_cluster_power_up : power up the specified cluster + * @cluster : the cluster to power up + */ +void exynos_cluster_power_up(int cluster) +{ + __raw_writel(S5P_CORE_LOCAL_PWR_EN, + EXYNOS_COMMON_CONFIGURATION(cluster)); +} + +/** + * exynos_cluster_power_state : returns the power state of the cluster + * @cluster : the cluster to retrieve the power state from + * + */ +int exynos_cluster_power_state(int cluster) +{ + return (__raw_readl(EXYNOS_COMMON_STATUS(cluster)) & + S5P_CORE_LOCAL_PWR_EN); +} + +#define EXYNOS_BOOT_VECTOR_ADDR (samsung_rev() == EXYNOS4210_REV_1_1 ? \ + S5P_INFORM7 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \ + (sysram_base_addr + 0x24) : S5P_INFORM0)) +#define EXYNOS_BOOT_VECTOR_FLAG (samsung_rev() == EXYNOS4210_REV_1_1 ? \ + S5P_INFORM6 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \ + (sysram_base_addr + 0x20) : S5P_INFORM1)) + +#define S5P_CHECK_AFTR 0xFCBA0D10 +#define S5P_CHECK_SLEEP 0x00000BAD + +/* Ext-GIC nIRQ/nFIQ is the only wakeup source in AFTR */ +static void exynos_set_wakeupmask(long mask) +{ + __raw_writel(mask, S5P_WAKEUP_MASK); +} + +static void exynos_cpu_set_boot_vector(long flags) +{ + __raw_writel(virt_to_phys(exynos_cpu_resume), EXYNOS_BOOT_VECTOR_ADDR); + __raw_writel(flags, EXYNOS_BOOT_VECTOR_FLAG); +} + +void exynos_enter_aftr(void) +{ + exynos_set_wakeupmask(0x0000ff3e); + exynos_cpu_set_boot_vector(S5P_CHECK_AFTR); + /* Set value of power down register for aftr mode */ + exynos_sys_powerdown_conf(SYS_AFTR); +} + /* For Cortex-A9 Diagnostic and Power control register */ static unsigned int save_arm_register[2]; +static void exynos_cpu_save_register(void) +{ + unsigned long tmp; + + /* Save Power control register */ + asm ("mrc p15, 0, %0, c15, c0, 0" + : "=r" (tmp) : : "cc"); + + save_arm_register[0] = tmp; + + /* Save Diagnostic register */ + asm ("mrc p15, 0, %0, c15, c0, 1" + : "=r" (tmp) : : "cc"); + + save_arm_register[1] = tmp; +} + +static void exynos_cpu_restore_register(void) +{ + unsigned long tmp; + + /* Restore Power control register */ + tmp = save_arm_register[0]; + + asm volatile ("mcr p15, 0, %0, c15, c0, 0" + : : "r" (tmp) + : "cc"); + + /* Restore Diagnostic register */ + tmp = save_arm_register[1]; + + asm volatile ("mcr p15, 0, %0, c15, c0, 1" + : : "r" (tmp) + : "cc"); +} + static int exynos_cpu_suspend(unsigned long arg) { #ifdef CONFIG_CACHE_L2X0 @@ -147,37 +280,34 @@ static void exynos_pm_prepare(void) __raw_writel(virt_to_phys(exynos_cpu_resume), S5P_INFORM0); } -static int exynos_pm_suspend(void) +static void exynos_pm_central_suspend(void) { unsigned long tmp; /* Setting Central Sequence Register for power down mode */ - tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION); tmp &= ~S5P_CENTRAL_LOWPWR_CFG; __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION); +} + +static int exynos_pm_suspend(void) +{ + unsigned long tmp; + + exynos_pm_central_suspend(); /* Setting SEQ_OPTION register */ tmp = (S5P_USE_STANDBY_WFI0 | S5P_USE_STANDBY_WFE0); __raw_writel(tmp, S5P_CENTRAL_SEQ_OPTION); - if (!soc_is_exynos5250()) { - /* Save Power control register */ - asm ("mrc p15, 0, %0, c15, c0, 0" - : "=r" (tmp) : : "cc"); - save_arm_register[0] = tmp; - - /* Save Diagnostic register */ - asm ("mrc p15, 0, %0, c15, c0, 1" - : "=r" (tmp) : : "cc"); - save_arm_register[1] = tmp; - } + if (!soc_is_exynos5250()) + exynos_cpu_save_register(); return 0; } -static void exynos_pm_resume(void) +static int exynos_pm_central_resume(void) { unsigned long tmp; @@ -194,22 +324,20 @@ static void exynos_pm_resume(void) /* clear the wakeup state register */ __raw_writel(0x0, S5P_WAKEUP_STAT); /* No need to perform below restore code */ - goto early_wakeup; - } - if (!soc_is_exynos5250()) { - /* Restore Power control register */ - tmp = save_arm_register[0]; - asm volatile ("mcr p15, 0, %0, c15, c0, 0" - : : "r" (tmp) - : "cc"); - - /* Restore Diagnostic register */ - tmp = save_arm_register[1]; - asm volatile ("mcr p15, 0, %0, c15, c0, 1" - : : "r" (tmp) - : "cc"); + return -1; } + return 0; +} + +static void exynos_pm_resume(void) +{ + if (exynos_pm_central_resume()) + goto early_wakeup; + + if (!soc_is_exynos5250()) + exynos_cpu_restore_register(); + /* For release retention */ __raw_writel((1 << 28), S5P_PAD_RET_MAUDIO_OPTION); @@ -226,7 +354,7 @@ static void exynos_pm_resume(void) s3c_pm_do_restore_core(exynos_core_save, ARRAY_SIZE(exynos_core_save)); - if (IS_ENABLED(CONFIG_SMP) && !soc_is_exynos5250()) + if (!soc_is_exynos5250()) scu_enable(S5P_VA_SCU); early_wakeup: @@ -304,10 +432,42 @@ static const struct platform_suspend_ops exynos_suspend_ops = { .valid = suspend_valid_only_mem, }; +static int exynos_cpu_pm_notifier(struct notifier_block *self, + unsigned long cmd, void *v) +{ + int cpu = smp_processor_id(); + + switch (cmd) { + case CPU_PM_ENTER: + if (cpu == 0) { + exynos_pm_central_suspend(); + exynos_cpu_save_register(); + } + break; + + case CPU_PM_EXIT: + if (cpu == 0) { + if (!soc_is_exynos5250()) + scu_enable(S5P_VA_SCU); + exynos_cpu_restore_register(); + exynos_pm_central_resume(); + } + break; + } + + return NOTIFY_OK; +} + +static struct notifier_block exynos_cpu_pm_notifier_block = { + .notifier_call = exynos_cpu_pm_notifier, +}; + void __init exynos_pm_init(void) { u32 tmp; + cpu_pm_register_notifier(&exynos_cpu_pm_notifier_block); + /* Platform-specific GIC callback */ gic_arch_extn.irq_set_wake = exynos_irq_set_wake; diff --git a/arch/arm/mach-exynos/regs-pmu.h b/arch/arm/mach-exynos/regs-pmu.h index 4f6a2560d022..1d13b08708f0 100644 --- a/arch/arm/mach-exynos/regs-pmu.h +++ b/arch/arm/mach-exynos/regs-pmu.h @@ -38,6 +38,7 @@ #define S5P_INFORM5 S5P_PMUREG(0x0814) #define S5P_INFORM6 S5P_PMUREG(0x0818) #define S5P_INFORM7 S5P_PMUREG(0x081C) +#define S5P_PMU_SPARE3 S5P_PMUREG(0x090C) #define S5P_ARM_CORE0_LOWPWR S5P_PMUREG(0x1000) #define S5P_DIS_IRQ_CORE0 S5P_PMUREG(0x1004) @@ -105,8 +106,17 @@ #define S5P_GPS_LOWPWR S5P_PMUREG(0x139C) #define S5P_GPS_ALIVE_LOWPWR S5P_PMUREG(0x13A0) -#define S5P_ARM_CORE1_CONFIGURATION S5P_PMUREG(0x2080) -#define S5P_ARM_CORE1_STATUS S5P_PMUREG(0x2084) +#define EXYNOS_ARM_CORE0_CONFIGURATION S5P_PMUREG(0x2000) +#define EXYNOS_ARM_CORE_CONFIGURATION(_nr) \ + (EXYNOS_ARM_CORE0_CONFIGURATION + (0x80 * (_nr))) +#define EXYNOS_ARM_CORE_STATUS(_nr) \ + (EXYNOS_ARM_CORE_CONFIGURATION(_nr) + 0x4) + +#define EXYNOS_ARM_COMMON_CONFIGURATION S5P_PMUREG(0x2500) +#define EXYNOS_COMMON_CONFIGURATION(_nr) \ + (EXYNOS_ARM_COMMON_CONFIGURATION + (0x80 * (_nr))) +#define EXYNOS_COMMON_STATUS(_nr) \ + (EXYNOS_COMMON_CONFIGURATION(_nr) + 0x4) #define S5P_PAD_RET_MAUDIO_OPTION S5P_PMUREG(0x3028) #define S5P_PAD_RET_GPIO_OPTION S5P_PMUREG(0x3108) @@ -119,8 +129,6 @@ #define S5P_CORE_LOCAL_PWR_EN 0x3 #define S5P_INT_LOCAL_PWR_EN 0x7 -#define S5P_CHECK_SLEEP 0x00000BAD - /* Only for EXYNOS4210 */ #define S5P_CMU_CLKSTOP_LCD1_LOWPWR S5P_PMUREG(0x1154) #define S5P_CMU_RESET_LCD1_LOWPWR S5P_PMUREG(0x1174) @@ -313,4 +321,6 @@ #define EXYNOS5_OPTION_USE_RETENTION (1 << 4) +#define EXYNOS5420_SWRESET_KFC_SEL 0x3 + #endif /* __ASM_ARCH_REGS_PMU_H */ diff --git a/arch/arm/mach-s3c24xx/Kconfig b/arch/arm/mach-s3c24xx/Kconfig index 40cf50b9940c..1e52b6926374 100644 --- a/arch/arm/mach-s3c24xx/Kconfig +++ b/arch/arm/mach-s3c24xx/Kconfig @@ -18,6 +18,8 @@ config PLAT_S3C24XX help Base platform code for any Samsung S3C24XX device + + menu "SAMSUNG S3C24XX SoCs Support" comment "S3C24XX SoCs" @@ -27,7 +29,7 @@ config CPU_S3C2410 default y select CPU_ARM920T select CPU_LLSERIAL_S3C2410 - select S3C2410_CLOCK + select S3C2410_COMMON_CLK select S3C2410_DMA if S3C24XX_DMA select ARM_S3C2410_CPUFREQ if ARM_S3C24XX_CPUFREQ select S3C2410_PM if PM @@ -40,6 +42,7 @@ config CPU_S3C2412 bool "SAMSUNG S3C2412" select CPU_ARM926T select CPU_LLSERIAL_S3C2440 + select S3C2412_COMMON_CLK select S3C2412_DMA if S3C24XX_DMA select S3C2412_PM if PM help @@ -50,9 +53,8 @@ config CPU_S3C2416 select CPU_ARM926T select CPU_LLSERIAL_S3C2440 select S3C2416_PM if PM - select S3C2443_COMMON + select S3C2443_COMMON_CLK select S3C2443_DMA if S3C24XX_DMA - select SAMSUNG_CLKSRC help Support for the S3C2416 SoC from the S3C24XX line @@ -60,7 +62,7 @@ config CPU_S3C2440 bool "SAMSUNG S3C2440" select CPU_ARM920T select CPU_LLSERIAL_S3C2440 - select S3C2410_CLOCK + select S3C2410_COMMON_CLK select S3C2410_PM if PM select S3C2440_DMA if S3C24XX_DMA help @@ -70,7 +72,7 @@ config CPU_S3C2442 bool "SAMSUNG S3C2442" select CPU_ARM920T select CPU_LLSERIAL_S3C2440 - select S3C2410_CLOCK + select S3C2410_COMMON_CLK select S3C2410_DMA if S3C24XX_DMA select S3C2410_PM if PM help @@ -85,25 +87,13 @@ config CPU_S3C2443 bool "SAMSUNG S3C2443" select CPU_ARM920T select CPU_LLSERIAL_S3C2440 - select S3C2443_COMMON + select S3C2443_COMMON_CLK select S3C2443_DMA if S3C24XX_DMA - select SAMSUNG_CLKSRC help Support for the S3C2443 SoC from the S3C24XX line # common code -config S3C2410_CLOCK - bool - help - Clock code for the S3C2410, and similar processors which - is currently includes the S3C2410, S3C2440, S3C2442. - -config S3C24XX_DCLK - bool - help - Clock code for supporting DCLK/CLKOUT on S3C24XX architectures - config S3C24XX_SMDK bool help @@ -258,8 +248,8 @@ config ARCH_BAST bool "Simtec Electronics BAST (EB2410ITX)" select ISA select MACH_BAST_IDE + select S3C2410_COMMON_DCLK select S3C2410_IOTIMING if ARM_S3C2410_CPUFREQ - select S3C24XX_DCLK select S3C24XX_SIMTEC_NOR select S3C24XX_SIMTEC_PM if PM select S3C24XX_SIMTEC_USB @@ -340,7 +330,7 @@ config MACH_TCT_HAMMER config MACH_VR1000 bool "Thorcom VR1000" select MACH_BAST_IDE - select S3C24XX_DCLK + select S3C2410_COMMON_DCLK select S3C24XX_SIMTEC_NOR select S3C24XX_SIMTEC_PM if PM select S3C24XX_SIMTEC_USB @@ -519,8 +509,8 @@ comment "S3C2440 Boards" config MACH_ANUBIS bool "Simtec Electronics ANUBIS" select HAVE_PATA_PLATFORM + select S3C2410_COMMON_DCLK select S3C2440_XTAL_12000000 - select S3C24XX_DCLK select S3C24XX_SIMTEC_PM if PM select S3C_DEV_USB_HOST help @@ -558,9 +548,9 @@ config MACH_NEXCODER_2440 config MACH_OSIRIS bool "Simtec IM2440D20 (OSIRIS) module" + select S3C2410_COMMON_DCLK select S3C2410_IOTIMING if ARM_S3C2440_CPUFREQ select S3C2440_XTAL_12000000 - select S3C24XX_DCLK select S3C24XX_SIMTEC_PM if PM select S3C_DEV_NAND select S3C_DEV_USB_HOST @@ -629,9 +619,9 @@ config MACH_RX1950 bool "HP iPAQ rx1950" select I2C select PM_H1940 if PM + select S3C2410_COMMON_DCLK select S3C2410_IOTIMING if ARM_S3C2440_CPUFREQ select S3C2440_XTAL_16934400 - select S3C24XX_DCLK select S3C24XX_PWM select S3C_DEV_NAND help @@ -641,12 +631,6 @@ endif # CPU_S3C2442 if CPU_S3C2443 || CPU_S3C2416 -config S3C2443_COMMON - bool - help - Common code for the S3C2443 and similar processors, which includes - the S3C2416 and S3C2450. - config S3C2443_DMA bool help diff --git a/arch/arm/mach-s3c24xx/Makefile b/arch/arm/mach-s3c24xx/Makefile index 7f54e5b954ca..2235d0d3b38d 100644 --- a/arch/arm/mach-s3c24xx/Makefile +++ b/arch/arm/mach-s3c24xx/Makefile @@ -21,22 +21,22 @@ obj-$(CONFIG_S3C2410_DMA) += dma-s3c2410.o obj-$(CONFIG_S3C2410_PLL) += pll-s3c2410.o obj-$(CONFIG_S3C2410_PM) += pm-s3c2410.o sleep-s3c2410.o -obj-$(CONFIG_CPU_S3C2412) += s3c2412.o clock-s3c2412.o +obj-$(CONFIG_CPU_S3C2412) += s3c2412.o obj-$(CONFIG_S3C2412_DMA) += dma-s3c2412.o obj-$(CONFIG_S3C2412_PM) += pm-s3c2412.o obj-$(CONFIG_S3C2412_PM_SLEEP) += sleep-s3c2412.o -obj-$(CONFIG_CPU_S3C2416) += s3c2416.o clock-s3c2416.o +obj-$(CONFIG_CPU_S3C2416) += s3c2416.o obj-$(CONFIG_S3C2416_PM) += pm-s3c2416.o -obj-$(CONFIG_CPU_S3C2440) += s3c2440.o clock-s3c2440.o +obj-$(CONFIG_CPU_S3C2440) += s3c2440.o obj-$(CONFIG_CPU_S3C2442) += s3c2442.o -obj-$(CONFIG_CPU_S3C244X) += s3c244x.o clock-s3c244x.o +obj-$(CONFIG_CPU_S3C244X) += s3c244x.o obj-$(CONFIG_S3C2440_DMA) += dma-s3c2440.o obj-$(CONFIG_S3C2440_PLL_12000000) += pll-s3c2440-12000000.o obj-$(CONFIG_S3C2440_PLL_16934400) += pll-s3c2440-16934400.o -obj-$(CONFIG_CPU_S3C2443) += s3c2443.o clock-s3c2443.o +obj-$(CONFIG_CPU_S3C2443) += s3c2443.o # PM @@ -44,16 +44,13 @@ obj-$(CONFIG_PM) += pm.o irq-pm.o sleep.o # common code -obj-$(CONFIG_S3C24XX_DCLK) += clock-dclk.o obj-$(CONFIG_S3C24XX_DMA) += dma.o -obj-$(CONFIG_S3C2410_CLOCK) += clock-s3c2410.o obj-$(CONFIG_S3C2410_CPUFREQ_UTILS) += cpufreq-utils.o obj-$(CONFIG_S3C2410_IOTIMING) += iotiming-s3c2410.o obj-$(CONFIG_S3C2412_IOTIMING) += iotiming-s3c2412.o -obj-$(CONFIG_S3C2443_COMMON) += common-s3c2443.o obj-$(CONFIG_S3C2443_DMA) += dma-s3c2443.o # diff --git a/arch/arm/mach-s3c24xx/clock-dclk.c b/arch/arm/mach-s3c24xx/clock-dclk.c deleted file mode 100644 index 1edd9b2369c5..000000000000 --- a/arch/arm/mach-s3c24xx/clock-dclk.c +++ /dev/null @@ -1,195 +0,0 @@ -/* - * Copyright (c) 2004-2008 Simtec Electronics - * Ben Dooks <ben@simtec.co.uk> - * http://armlinux.simtec.co.uk/ - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * - * S3C24XX - definitions for DCLK and CLKOUT registers - */ - -#include <linux/kernel.h> -#include <linux/errno.h> -#include <linux/clk.h> -#include <linux/io.h> - -#include <mach/regs-clock.h> -#include <mach/regs-gpio.h> - -#include <plat/clock.h> -#include <plat/cpu.h> - -/* clocks that could be registered by external code */ - -static int s3c24xx_dclk_enable(struct clk *clk, int enable) -{ - unsigned long dclkcon = __raw_readl(S3C24XX_DCLKCON); - - if (enable) - dclkcon |= clk->ctrlbit; - else - dclkcon &= ~clk->ctrlbit; - - __raw_writel(dclkcon, S3C24XX_DCLKCON); - - return 0; -} - -static int s3c24xx_dclk_setparent(struct clk *clk, struct clk *parent) -{ - unsigned long dclkcon; - unsigned int uclk; - - if (parent == &clk_upll) - uclk = 1; - else if (parent == &clk_p) - uclk = 0; - else - return -EINVAL; - - clk->parent = parent; - - dclkcon = __raw_readl(S3C24XX_DCLKCON); - - if (clk->ctrlbit == S3C2410_DCLKCON_DCLK0EN) { - if (uclk) - dclkcon |= S3C2410_DCLKCON_DCLK0_UCLK; - else - dclkcon &= ~S3C2410_DCLKCON_DCLK0_UCLK; - } else { - if (uclk) - dclkcon |= S3C2410_DCLKCON_DCLK1_UCLK; - else - dclkcon &= ~S3C2410_DCLKCON_DCLK1_UCLK; - } - - __raw_writel(dclkcon, S3C24XX_DCLKCON); - - return 0; -} -static unsigned long s3c24xx_calc_div(struct clk *clk, unsigned long rate) -{ - unsigned long div; - - if ((rate == 0) || !clk->parent) - return 0; - - div = clk_get_rate(clk->parent) / rate; - if (div < 2) - div = 2; - else if (div > 16) - div = 16; - - return div; -} - -static unsigned long s3c24xx_round_dclk_rate(struct clk *clk, - unsigned long rate) -{ - unsigned long div = s3c24xx_calc_div(clk, rate); - - if (div == 0) - return 0; - - return clk_get_rate(clk->parent) / div; -} - -static int s3c24xx_set_dclk_rate(struct clk *clk, unsigned long rate) -{ - unsigned long mask, data, div = s3c24xx_calc_div(clk, rate); - - if (div == 0) - return -EINVAL; - - if (clk == &s3c24xx_dclk0) { - mask = S3C2410_DCLKCON_DCLK0_DIV_MASK | - S3C2410_DCLKCON_DCLK0_CMP_MASK; - data = S3C2410_DCLKCON_DCLK0_DIV(div) | - S3C2410_DCLKCON_DCLK0_CMP((div + 1) / 2); - } else if (clk == &s3c24xx_dclk1) { - mask = S3C2410_DCLKCON_DCLK1_DIV_MASK | - S3C2410_DCLKCON_DCLK1_CMP_MASK; - data = S3C2410_DCLKCON_DCLK1_DIV(div) | - S3C2410_DCLKCON_DCLK1_CMP((div + 1) / 2); - } else - return -EINVAL; - - clk->rate = clk_get_rate(clk->parent) / div; - __raw_writel(((__raw_readl(S3C24XX_DCLKCON) & ~mask) | data), - S3C24XX_DCLKCON); - return clk->rate; -} -static int s3c24xx_clkout_setparent(struct clk *clk, struct clk *parent) -{ - unsigned long mask; - unsigned long source; - - /* calculate the MISCCR setting for the clock */ - - if (parent == &clk_mpll) - source = S3C2410_MISCCR_CLK0_MPLL; - else if (parent == &clk_upll) - source = S3C2410_MISCCR_CLK0_UPLL; - else if (parent == &clk_f) - source = S3C2410_MISCCR_CLK0_FCLK; - else if (parent == &clk_h) - source = S3C2410_MISCCR_CLK0_HCLK; - else if (parent == &clk_p) - source = S3C2410_MISCCR_CLK0_PCLK; - else if (clk == &s3c24xx_clkout0 && parent == &s3c24xx_dclk0) - source = S3C2410_MISCCR_CLK0_DCLK0; - else if (clk == &s3c24xx_clkout1 && parent == &s3c24xx_dclk1) - source = S3C2410_MISCCR_CLK0_DCLK0; - else - return -EINVAL; - - clk->parent = parent; - - if (clk == &s3c24xx_clkout0) - mask = S3C2410_MISCCR_CLK0_MASK; - else { - source <<= 4; - mask = S3C2410_MISCCR_CLK1_MASK; - } - - s3c2410_modify_misccr(mask, source); - return 0; -} - -/* external clock definitions */ - -static struct clk_ops dclk_ops = { - .set_parent = s3c24xx_dclk_setparent, - .set_rate = s3c24xx_set_dclk_rate, - .round_rate = s3c24xx_round_dclk_rate, -}; - -struct clk s3c24xx_dclk0 = { - .name = "dclk0", - .ctrlbit = S3C2410_DCLKCON_DCLK0EN, - .enable = s3c24xx_dclk_enable, - .ops = &dclk_ops, -}; - -struct clk s3c24xx_dclk1 = { - .name = "dclk1", - .ctrlbit = S3C2410_DCLKCON_DCLK1EN, - .enable = s3c24xx_dclk_enable, - .ops = &dclk_ops, -}; - -static struct clk_ops clkout_ops = { - .set_parent = s3c24xx_clkout_setparent, -}; - -struct clk s3c24xx_clkout0 = { - .name = "clkout0", - .ops = &clkout_ops, -}; - -struct clk s3c24xx_clkout1 = { - .name = "clkout1", - .ops = &clkout_ops, -}; diff --git a/arch/arm/mach-s3c24xx/clock-s3c2410.c b/arch/arm/mach-s3c24xx/clock-s3c2410.c deleted file mode 100644 index d1afcf9252d1..000000000000 --- a/arch/arm/mach-s3c24xx/clock-s3c2410.c +++ /dev/null @@ -1,284 +0,0 @@ -/* - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks <ben@simtec.co.uk> - * - * S3C2410,S3C2440,S3C2442 Clock control support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include <linux/init.h> -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/list.h> -#include <linux/errno.h> -#include <linux/err.h> -#include <linux/device.h> -#include <linux/clk.h> -#include <linux/mutex.h> -#include <linux/delay.h> -#include <linux/serial_core.h> -#include <linux/serial_s3c.h> -#include <linux/io.h> - -#include <asm/mach/map.h> - -#include <mach/hardware.h> -#include <mach/regs-clock.h> -#include <mach/regs-gpio.h> - -#include <plat/clock.h> -#include <plat/cpu.h> - -int s3c2410_clkcon_enable(struct clk *clk, int enable) -{ - unsigned int clocks = clk->ctrlbit; - unsigned long clkcon; - - clkcon = __raw_readl(S3C2410_CLKCON); - - if (enable) - clkcon |= clocks; - else - clkcon &= ~clocks; - - /* ensure none of the special function bits set */ - clkcon &= ~(S3C2410_CLKCON_IDLE|S3C2410_CLKCON_POWER); - - __raw_writel(clkcon, S3C2410_CLKCON); - - return 0; -} - -static int s3c2410_upll_enable(struct clk *clk, int enable) -{ - unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW); - unsigned long orig = clkslow; - - if (enable) - clkslow &= ~S3C2410_CLKSLOW_UCLK_OFF; - else - clkslow |= S3C2410_CLKSLOW_UCLK_OFF; - - __raw_writel(clkslow, S3C2410_CLKSLOW); - - /* if we started the UPLL, then allow to settle */ - - if (enable && (orig & S3C2410_CLKSLOW_UCLK_OFF)) - udelay(200); - - return 0; -} - -/* standard clock definitions */ - -static struct clk init_clocks_off[] = { - { - .name = "nand", - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_NAND, - }, { - .name = "sdi", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_SDI, - }, { - .name = "adc", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_ADC, - }, { - .name = "i2c", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_IIC, - }, { - .name = "iis", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_IIS, - }, { - .name = "spi", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_SPI, - } -}; - -static struct clk clk_lcd = { - .name = "lcd", - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_LCDC, -}; - -static struct clk clk_gpio = { - .name = "gpio", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_GPIO, -}; - -static struct clk clk_usb_host = { - .name = "usb-host", - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBH, -}; - -static struct clk clk_usb_device = { - .name = "usb-device", - .parent = &clk_h, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_USBD, -}; - -static struct clk clk_timers = { - .name = "timers", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_PWMT, -}; - -struct clk s3c24xx_clk_uart0 = { - .name = "uart", - .devname = "s3c2410-uart.0", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART0, -}; - -struct clk s3c24xx_clk_uart1 = { - .name = "uart", - .devname = "s3c2410-uart.1", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART1, -}; - -struct clk s3c24xx_clk_uart2 = { - .name = "uart", - .devname = "s3c2410-uart.2", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_UART2, -}; - -static struct clk clk_rtc = { - .name = "rtc", - .parent = &clk_p, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2410_CLKCON_RTC, -}; - -static struct clk clk_watchdog = { - .name = "watchdog", - .parent = &clk_p, - .ctrlbit = 0, -}; - -static struct clk clk_usb_bus_host = { - .name = "usb-bus-host", - .parent = &clk_usb_bus, -}; - -static struct clk clk_usb_bus_gadget = { - .name = "usb-bus-gadget", - .parent = &clk_usb_bus, -}; - -static struct clk *init_clocks[] = { - &clk_lcd, - &clk_gpio, - &clk_usb_host, - &clk_usb_device, - &clk_timers, - &s3c24xx_clk_uart0, - &s3c24xx_clk_uart1, - &s3c24xx_clk_uart2, - &clk_rtc, - &clk_watchdog, - &clk_usb_bus_host, - &clk_usb_bus_gadget, -}; - -/* s3c2410_baseclk_add() - * - * Add all the clocks used by the s3c2410 or compatible CPUs - * such as the S3C2440 and S3C2442. - * - * We cannot use a system device as we are needed before any - * of the init-calls that initialise the devices are actually - * done. -*/ - -int __init s3c2410_baseclk_add(void) -{ - unsigned long clkslow = __raw_readl(S3C2410_CLKSLOW); - unsigned long clkcon = __raw_readl(S3C2410_CLKCON); - struct clk *xtal; - int ret; - int ptr; - - clk_upll.enable = s3c2410_upll_enable; - - if (s3c24xx_register_clock(&clk_usb_bus) < 0) - printk(KERN_ERR "failed to register usb bus clock\n"); - - /* register clocks from clock array */ - - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++) { - struct clk *clkp = init_clocks[ptr]; - - /* ensure that we note the clock state */ - - clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0; - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - } - - /* We must be careful disabling the clocks we are not intending to - * be using at boot time, as subsystems such as the LCD which do - * their own DMA requests to the bus can cause the system to lockup - * if they where in the middle of requesting bus access. - * - * Disabling the LCD clock if the LCD is active is very dangerous, - * and therefore the bootloader should be careful to not enable - * the LCD clock if it is not needed. - */ - - /* install (and disable) the clocks we do not need immediately */ - - s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off)); - s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off)); - - /* show the clock-slow value */ - - xtal = clk_get(NULL, "xtal"); - - printk("CLOCK: Slow mode (%ld.%ld MHz), %s, MPLL %s, UPLL %s\n", - print_mhz(clk_get_rate(xtal) / - ( 2 * S3C2410_CLKSLOW_GET_SLOWVAL(clkslow))), - (clkslow & S3C2410_CLKSLOW_SLOW) ? "slow" : "fast", - (clkslow & S3C2410_CLKSLOW_MPLL_OFF) ? "off" : "on", - (clkslow & S3C2410_CLKSLOW_UCLK_OFF) ? "off" : "on"); - - return 0; -} diff --git a/arch/arm/mach-s3c24xx/clock-s3c2412.c b/arch/arm/mach-s3c24xx/clock-s3c2412.c deleted file mode 100644 index 192a5b2550b0..000000000000 --- a/arch/arm/mach-s3c24xx/clock-s3c2412.c +++ /dev/null @@ -1,760 +0,0 @@ -/* linux/arch/arm/mach-s3c2412/clock.c - * - * Copyright (c) 2006 Simtec Electronics - * Ben Dooks <ben@simtec.co.uk> - * - * S3C2412,S3C2413 Clock control support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include <linux/init.h> -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/list.h> -#include <linux/errno.h> -#include <linux/err.h> -#include <linux/device.h> -#include <linux/clk.h> -#include <linux/mutex.h> -#include <linux/delay.h> -#include <linux/serial_core.h> -#include <linux/serial_s3c.h> -#include <linux/io.h> - -#include <asm/mach/map.h> - -#include <mach/hardware.h> -#include <mach/regs-clock.h> -#include <mach/regs-gpio.h> - -#include <plat/clock.h> -#include <plat/cpu.h> - -/* We currently have to assume that the system is running - * from the XTPll input, and that all ***REFCLKs are being - * fed from it, as we cannot read the state of OM[4] from - * software. - * - * It would be possible for each board initialisation to - * set the correct muxing at initialisation -*/ - -static int s3c2412_clkcon_enable(struct clk *clk, int enable) -{ - unsigned int clocks = clk->ctrlbit; - unsigned long clkcon; - - clkcon = __raw_readl(S3C2410_CLKCON); - - if (enable) - clkcon |= clocks; - else - clkcon &= ~clocks; - - __raw_writel(clkcon, S3C2410_CLKCON); - - return 0; -} - -static int s3c2412_upll_enable(struct clk *clk, int enable) -{ - unsigned long upllcon = __raw_readl(S3C2410_UPLLCON); - unsigned long orig = upllcon; - - if (!enable) - upllcon |= S3C2412_PLLCON_OFF; - else - upllcon &= ~S3C2412_PLLCON_OFF; - - __raw_writel(upllcon, S3C2410_UPLLCON); - - /* allow ~150uS for the PLL to settle and lock */ - - if (enable && (orig & S3C2412_PLLCON_OFF)) - udelay(150); - - return 0; -} - -/* clock selections */ - -static struct clk clk_erefclk = { - .name = "erefclk", -}; - -static struct clk clk_urefclk = { - .name = "urefclk", -}; - -static int s3c2412_setparent_usysclk(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_urefclk) - clksrc &= ~S3C2412_CLKSRC_USYSCLK_UPLL; - else if (parent == &clk_upll) - clksrc |= S3C2412_CLKSRC_USYSCLK_UPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static struct clk clk_usysclk = { - .name = "usysclk", - .parent = &clk_xtal, - .ops = &(struct clk_ops) { - .set_parent = s3c2412_setparent_usysclk, - }, -}; - -static struct clk clk_mrefclk = { - .name = "mrefclk", - .parent = &clk_xtal, -}; - -static struct clk clk_mdivclk = { - .name = "mdivclk", - .parent = &clk_xtal, -}; - -static int s3c2412_setparent_usbsrc(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_usysclk) - clksrc &= ~S3C2412_CLKSRC_USBCLK_HCLK; - else if (parent == &clk_h) - clksrc |= S3C2412_CLKSRC_USBCLK_HCLK; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static unsigned long s3c2412_roundrate_usbsrc(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - div = parent_rate / rate; - if (div > 2) - div = 2; - - return parent_rate / div; -} - -static unsigned long s3c2412_getrate_usbsrc(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - return parent_rate / ((div & S3C2412_CLKDIVN_USB48DIV) ? 2 : 1); -} - -static int s3c2412_setrate_usbsrc(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_usbsrc(clk, rate); - - if ((parent_rate / rate) == 2) - clkdivn |= S3C2412_CLKDIVN_USB48DIV; - else - clkdivn &= ~S3C2412_CLKDIVN_USB48DIV; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_usbsrc = { - .name = "usbsrc", - .ops = &(struct clk_ops) { - .get_rate = s3c2412_getrate_usbsrc, - .set_rate = s3c2412_setrate_usbsrc, - .round_rate = s3c2412_roundrate_usbsrc, - .set_parent = s3c2412_setparent_usbsrc, - }, -}; - -static int s3c2412_setparent_msysclk(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_mdivclk) - clksrc &= ~S3C2412_CLKSRC_MSYSCLK_MPLL; - else if (parent == &clk_mpll) - clksrc |= S3C2412_CLKSRC_MSYSCLK_MPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static struct clk clk_msysclk = { - .name = "msysclk", - .ops = &(struct clk_ops) { - .set_parent = s3c2412_setparent_msysclk, - }, -}; - -static int s3c2412_setparent_armclk(struct clk *clk, struct clk *parent) -{ - unsigned long flags; - unsigned long clkdiv; - unsigned long dvs; - - /* Note, we current equate fclk andf msysclk for S3C2412 */ - - if (parent == &clk_msysclk || parent == &clk_f) - dvs = 0; - else if (parent == &clk_h) - dvs = S3C2412_CLKDIVN_DVSEN; - else - return -EINVAL; - - clk->parent = parent; - - /* update this under irq lockdown, clkdivn is not protected - * by the clock system. */ - - local_irq_save(flags); - - clkdiv = __raw_readl(S3C2410_CLKDIVN); - clkdiv &= ~S3C2412_CLKDIVN_DVSEN; - clkdiv |= dvs; - __raw_writel(clkdiv, S3C2410_CLKDIVN); - - local_irq_restore(flags); - - return 0; -} - -static struct clk clk_armclk = { - .name = "armclk", - .parent = &clk_msysclk, - .ops = &(struct clk_ops) { - .set_parent = s3c2412_setparent_armclk, - }, -}; - -/* these next clocks have an divider immediately after them, - * so we can register them with their divider and leave out the - * intermediate clock stage -*/ -static unsigned long s3c2412_roundrate_clksrc(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - /* note, we remove the +/- 1 calculations as they cancel out */ - - div = (rate / parent_rate); - - if (div < 1) - div = 1; - else if (div > 16) - div = 16; - - return parent_rate / div; -} - -static int s3c2412_setparent_uart(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_erefclk) - clksrc &= ~S3C2412_CLKSRC_UARTCLK_MPLL; - else if (parent == &clk_mpll) - clksrc |= S3C2412_CLKSRC_UARTCLK_MPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static unsigned long s3c2412_getrate_uart(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - div &= S3C2412_CLKDIVN_UARTDIV_MASK; - div >>= S3C2412_CLKDIVN_UARTDIV_SHIFT; - - return parent_rate / (div + 1); -} - -static int s3c2412_setrate_uart(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_clksrc(clk, rate); - - clkdivn &= ~S3C2412_CLKDIVN_UARTDIV_MASK; - clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_UARTDIV_SHIFT; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_uart = { - .name = "uartclk", - .ops = &(struct clk_ops) { - .get_rate = s3c2412_getrate_uart, - .set_rate = s3c2412_setrate_uart, - .set_parent = s3c2412_setparent_uart, - .round_rate = s3c2412_roundrate_clksrc, - }, -}; - -static int s3c2412_setparent_i2s(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_erefclk) - clksrc &= ~S3C2412_CLKSRC_I2SCLK_MPLL; - else if (parent == &clk_mpll) - clksrc |= S3C2412_CLKSRC_I2SCLK_MPLL; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} - -static unsigned long s3c2412_getrate_i2s(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - div &= S3C2412_CLKDIVN_I2SDIV_MASK; - div >>= S3C2412_CLKDIVN_I2SDIV_SHIFT; - - return parent_rate / (div + 1); -} - -static int s3c2412_setrate_i2s(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_clksrc(clk, rate); - - clkdivn &= ~S3C2412_CLKDIVN_I2SDIV_MASK; - clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_I2SDIV_SHIFT; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_i2s = { - .name = "i2sclk", - .ops = &(struct clk_ops) { - .get_rate = s3c2412_getrate_i2s, - .set_rate = s3c2412_setrate_i2s, - .set_parent = s3c2412_setparent_i2s, - .round_rate = s3c2412_roundrate_clksrc, - }, -}; - -static int s3c2412_setparent_cam(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - - if (parent == &clk_usysclk) - clksrc &= ~S3C2412_CLKSRC_CAMCLK_HCLK; - else if (parent == &clk_h) - clksrc |= S3C2412_CLKSRC_CAMCLK_HCLK; - else - return -EINVAL; - - clk->parent = parent; - - __raw_writel(clksrc, S3C2412_CLKSRC); - return 0; -} -static unsigned long s3c2412_getrate_cam(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2410_CLKDIVN); - - div &= S3C2412_CLKDIVN_CAMDIV_MASK; - div >>= S3C2412_CLKDIVN_CAMDIV_SHIFT; - - return parent_rate / (div + 1); -} - -static int s3c2412_setrate_cam(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long clkdivn = __raw_readl(S3C2410_CLKDIVN); - - rate = s3c2412_roundrate_clksrc(clk, rate); - - clkdivn &= ~S3C2412_CLKDIVN_CAMDIV_MASK; - clkdivn |= ((parent_rate / rate) - 1) << S3C2412_CLKDIVN_CAMDIV_SHIFT; - - __raw_writel(clkdivn, S3C2410_CLKDIVN); - return 0; -} - -static struct clk clk_cam = { - .name = "camif-upll", /* same as 2440 name */ - .ops = &(struct clk_ops) { - .get_rate = s3c2412_getrate_cam, - .set_rate = s3c2412_setrate_cam, - .set_parent = s3c2412_setparent_cam, - .round_rate = s3c2412_roundrate_clksrc, - }, -}; - -/* standard clock definitions */ - -static struct clk init_clocks_disable[] = { - { - .name = "nand", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_NAND, - }, { - .name = "sdi", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_SDI, - }, { - .name = "adc", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_ADC, - }, { - .name = "i2c", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_IIC, - }, { - .name = "iis", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_IIS, - }, { - .name = "spi", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_SPI, - } -}; - -static struct clk init_clocks[] = { - { - .name = "dma.0", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA0, - }, { - .name = "dma.1", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA1, - }, { - .name = "dma.2", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA2, - }, { - .name = "dma.3", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_DMA3, - }, { - .name = "lcd", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_LCDC, - }, { - .name = "gpio", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_GPIO, - }, { - .name = "usb-host", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USBH, - }, { - .name = "usb-device", - .parent = &clk_h, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USBD, - }, { - .name = "timers", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_PWMT, - }, { - .name = "uart", - .devname = "s3c2412-uart.0", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_UART0, - }, { - .name = "uart", - .devname = "s3c2412-uart.1", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_UART1, - }, { - .name = "uart", - .devname = "s3c2412-uart.2", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_UART2, - }, { - .name = "rtc", - .parent = &clk_p, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_RTC, - }, { - .name = "watchdog", - .parent = &clk_p, - .ctrlbit = 0, - }, { - .name = "usb-bus-gadget", - .parent = &clk_usb_bus, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USB_DEV48, - }, { - .name = "usb-bus-host", - .parent = &clk_usb_bus, - .enable = s3c2412_clkcon_enable, - .ctrlbit = S3C2412_CLKCON_USB_HOST48, - } -}; - -/* clocks to add where we need to check their parentage */ - -struct clk_init { - struct clk *clk; - unsigned int bit; - struct clk *src_0; - struct clk *src_1; -}; - -static struct clk_init clks_src[] __initdata = { - { - .clk = &clk_usysclk, - .bit = S3C2412_CLKSRC_USBCLK_HCLK, - .src_0 = &clk_urefclk, - .src_1 = &clk_upll, - }, { - .clk = &clk_i2s, - .bit = S3C2412_CLKSRC_I2SCLK_MPLL, - .src_0 = &clk_erefclk, - .src_1 = &clk_mpll, - }, { - .clk = &clk_cam, - .bit = S3C2412_CLKSRC_CAMCLK_HCLK, - .src_0 = &clk_usysclk, - .src_1 = &clk_h, - }, { - .clk = &clk_msysclk, - .bit = S3C2412_CLKSRC_MSYSCLK_MPLL, - .src_0 = &clk_mdivclk, - .src_1 = &clk_mpll, - }, { - .clk = &clk_uart, - .bit = S3C2412_CLKSRC_UARTCLK_MPLL, - .src_0 = &clk_erefclk, - .src_1 = &clk_mpll, - }, { - .clk = &clk_usbsrc, - .bit = S3C2412_CLKSRC_USBCLK_HCLK, - .src_0 = &clk_usysclk, - .src_1 = &clk_h, - /* here we assume OM[4] select xtal */ - }, { - .clk = &clk_erefclk, - .bit = S3C2412_CLKSRC_EREFCLK_EXTCLK, - .src_0 = &clk_xtal, - .src_1 = &clk_ext, - }, { - .clk = &clk_urefclk, - .bit = S3C2412_CLKSRC_UREFCLK_EXTCLK, - .src_0 = &clk_xtal, - .src_1 = &clk_ext, - }, -}; - -/* s3c2412_clk_initparents - * - * Initialise the parents for the clocks that we get at start-time -*/ - -static void __init s3c2412_clk_initparents(void) -{ - unsigned long clksrc = __raw_readl(S3C2412_CLKSRC); - struct clk_init *cip = clks_src; - struct clk *src; - int ptr; - int ret; - - for (ptr = 0; ptr < ARRAY_SIZE(clks_src); ptr++, cip++) { - ret = s3c24xx_register_clock(cip->clk); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - cip->clk->name, ret); - } - - src = (clksrc & cip->bit) ? cip->src_1 : cip->src_0; - - printk(KERN_INFO "%s: parent %s\n", cip->clk->name, src->name); - clk_set_parent(cip->clk, src); - } -} - -/* clocks to add straight away */ - -static struct clk *clks[] __initdata = { - &clk_ext, - &clk_usb_bus, - &clk_mrefclk, - &clk_armclk, -}; - -static struct clk_lookup s3c2412_clk_lookup[] = { - CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk), - CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p), - CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_usysclk), -}; - -int __init s3c2412_baseclk_add(void) -{ - unsigned long clkcon = __raw_readl(S3C2410_CLKCON); - unsigned int dvs; - struct clk *clkp; - int ret; - int ptr; - - clk_upll.enable = s3c2412_upll_enable; - clk_usb_bus.parent = &clk_usbsrc; - clk_usb_bus.rate = 0x0; - - clk_f.parent = &clk_msysclk; - - s3c2412_clk_initparents(); - - for (ptr = 0; ptr < ARRAY_SIZE(clks); ptr++) { - clkp = clks[ptr]; - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - } - - /* set the dvs state according to what we got at boot time */ - - dvs = __raw_readl(S3C2410_CLKDIVN) & S3C2412_CLKDIVN_DVSEN; - - if (dvs) - clk_armclk.parent = &clk_h; - - printk(KERN_INFO "S3C2412: DVS is %s\n", dvs ? "on" : "off"); - - /* ensure usb bus clock is within correct rate of 48MHz */ - - if (clk_get_rate(&clk_usb_bus) != (48 * 1000 * 1000)) { - printk(KERN_INFO "Warning: USB bus clock not at 48MHz\n"); - - /* for the moment, let's use the UPLL, and see if we can - * get 48MHz */ - - clk_set_parent(&clk_usysclk, &clk_upll); - clk_set_parent(&clk_usbsrc, &clk_usysclk); - clk_set_rate(&clk_usbsrc, 48*1000*1000); - } - - printk("S3C2412: upll %s, %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n", - (__raw_readl(S3C2410_UPLLCON) & S3C2412_PLLCON_OFF) ? "off":"on", - print_mhz(clk_get_rate(&clk_upll)), - print_mhz(clk_get_rate(&clk_usb_bus))); - - /* register clocks from clock array */ - - clkp = init_clocks; - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks); ptr++, clkp++) { - /* ensure that we note the clock state */ - - clkp->usage = clkcon & clkp->ctrlbit ? 1 : 0; - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - } - - /* We must be careful disabling the clocks we are not intending to - * be using at boot time, as subsystems such as the LCD which do - * their own DMA requests to the bus can cause the system to lockup - * if they where in the middle of requesting bus access. - * - * Disabling the LCD clock if the LCD is active is very dangerous, - * and therefore the bootloader should be careful to not enable - * the LCD clock if it is not needed. - */ - - /* install (and disable) the clocks we do not need immediately */ - - clkp = init_clocks_disable; - for (ptr = 0; ptr < ARRAY_SIZE(init_clocks_disable); ptr++, clkp++) { - - ret = s3c24xx_register_clock(clkp); - if (ret < 0) { - printk(KERN_ERR "Failed to register clock %s (%d)\n", - clkp->name, ret); - } - - s3c2412_clkcon_enable(clkp, 0); - } - - clkdev_add_table(s3c2412_clk_lookup, ARRAY_SIZE(s3c2412_clk_lookup)); - return 0; -} diff --git a/arch/arm/mach-s3c24xx/clock-s3c2416.c b/arch/arm/mach-s3c24xx/clock-s3c2416.c deleted file mode 100644 index d421a72920a5..000000000000 --- a/arch/arm/mach-s3c24xx/clock-s3c2416.c +++ /dev/null @@ -1,171 +0,0 @@ -/* linux/arch/arm/mach-s3c2416/clock.c - * - * Copyright (c) 2010 Simtec Electronics - * Copyright (c) 2010 Ben Dooks <ben-linux@fluff.org> - * - * S3C2416 Clock control support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#include <linux/init.h> -#include <linux/clk.h> - -#include <plat/clock.h> -#include <plat/clock-clksrc.h> -#include <plat/cpu.h> - -#include <plat/cpu-freq.h> -#include <plat/pll.h> - -#include <asm/mach/map.h> - -#include <mach/regs-clock.h> -#include <mach/regs-s3c2443-clock.h> - -/* armdiv - * - * this clock is sourced from msysclk and can have a number of - * divider values applied to it to then be fed into armclk. - * The real clock definition is done in s3c2443-clock.c, - * only the armdiv divisor table must be defined here. -*/ - -static unsigned int armdiv[8] = { - [0] = 1, - [1] = 2, - [2] = 3, - [3] = 4, - [5] = 6, - [7] = 8, -}; - -static struct clksrc_clk hsspi_eplldiv = { - .clk = { - .name = "hsspi-eplldiv", - .parent = &clk_esysclk.clk, - .ctrlbit = (1 << 14), - .enable = s3c2443_clkcon_enable_s, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 24 }, -}; - -static struct clk *hsspi_sources[] = { - [0] = &hsspi_eplldiv.clk, - [1] = NULL, /* to fix */ -}; - -static struct clksrc_clk hsspi_mux = { - .clk = { - .name = "hsspi-if", - }, - .sources = &(struct clksrc_sources) { - .sources = hsspi_sources, - .nr_sources = ARRAY_SIZE(hsspi_sources), - }, - .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 18 }, -}; - -static struct clksrc_clk hsmmc_div[] = { - [0] = { - .clk = { - .name = "hsmmc-div", - .devname = "s3c-sdhci.0", - .parent = &clk_esysclk.clk, - }, - .reg_div = { .reg = S3C2416_CLKDIV2, .size = 2, .shift = 6 }, - }, - [1] = { - .clk = { - .name = "hsmmc-div", - .devname = "s3c-sdhci.1", - .parent = &clk_esysclk.clk, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 6 }, - }, -}; - -static struct clksrc_clk hsmmc_mux0 = { - .clk = { - .name = "hsmmc-if", - .devname = "s3c-sdhci.0", - .ctrlbit = (1 << 6), - .enable = s3c2443_clkcon_enable_s, - }, - .sources = &(struct clksrc_sources) { - .nr_sources = 2, - .sources = (struct clk * []) { - [0] = &hsmmc_div[0].clk, - [1] = NULL, /* to fix */ - }, - }, - .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 16 }, -}; - -static struct clksrc_clk hsmmc_mux1 = { - .clk = { - .name = "hsmmc-if", - .devname = "s3c-sdhci.1", - .ctrlbit = (1 << 12), - .enable = s3c2443_clkcon_enable_s, - }, - .sources = &(struct clksrc_sources) { - .nr_sources = 2, - .sources = (struct clk * []) { - [0] = &hsmmc_div[1].clk, - [1] = NULL, /* to fix */ - }, - }, - .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 17 }, -}; - -static struct clk hsmmc0_clk = { - .name = "hsmmc", - .devname = "s3c-sdhci.0", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2416_HCLKCON_HSMMC0, -}; - -static struct clksrc_clk *clksrcs[] __initdata = { - &hsspi_eplldiv, - &hsspi_mux, - &hsmmc_div[0], - &hsmmc_div[1], - &hsmmc_mux0, - &hsmmc_mux1, -}; - -static struct clk_lookup s3c2416_clk_lookup[] = { - CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &hsmmc0_clk), - CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &hsmmc_mux0.clk), - CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &hsmmc_mux1.clk), - /* s3c2443-spi.0 is used on s3c2416 and s3c2450 as well */ - CLKDEV_INIT("s3c2443-spi.0", "spi_busclk2", &hsspi_mux.clk), -}; - -void __init s3c2416_init_clocks(int xtal) -{ - u32 epllcon = __raw_readl(S3C2443_EPLLCON); - u32 epllcon1 = __raw_readl(S3C2443_EPLLCON+4); - int ptr; - - /* s3c2416 EPLL compatible with s3c64xx */ - clk_epll.rate = s3c_get_pll6553x(xtal, epllcon, epllcon1); - - clk_epll.parent = &clk_epllref.clk; - - s3c2443_common_init_clocks(xtal, s3c2416_get_pll, - armdiv, ARRAY_SIZE(armdiv), - S3C2416_CLKDIV0_ARMDIV_MASK); - - for (ptr = 0; ptr < ARRAY_SIZE(clksrcs); ptr++) - s3c_register_clksrc(clksrcs[ptr], 1); - - s3c24xx_register_clock(&hsmmc0_clk); - clkdev_add_table(s3c2416_clk_lookup, ARRAY_SIZE(s3c2416_clk_lookup)); - -} diff --git a/arch/arm/mach-s3c24xx/clock-s3c2440.c b/arch/arm/mach-s3c24xx/clock-s3c2440.c deleted file mode 100644 index 5527226fd61f..000000000000 --- a/arch/arm/mach-s3c24xx/clock-s3c2440.c +++ /dev/null @@ -1,217 +0,0 @@ -/* linux/arch/arm/mach-s3c2440/clock.c - * - * Copyright (c) 2004-2005 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * Ben Dooks <ben@simtec.co.uk> - * - * S3C2440 Clock support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include <linux/init.h> -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/list.h> -#include <linux/errno.h> -#include <linux/err.h> -#include <linux/device.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/mutex.h> -#include <linux/clk.h> -#include <linux/io.h> -#include <linux/serial_core.h> -#include <linux/serial_s3c.h> - -#include <mach/hardware.h> -#include <linux/atomic.h> -#include <asm/irq.h> - -#include <mach/regs-clock.h> - -#include <plat/clock.h> -#include <plat/cpu.h> - -/* S3C2440 extended clock support */ - -static unsigned long s3c2440_camif_upll_round(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - /* note, we remove the +/- 1 calculations for the divisor */ - - div = (parent_rate / rate) / 2; - - if (div < 1) - div = 1; - else if (div > 16) - div = 16; - - return parent_rate / (div * 2); -} - -static int s3c2440_camif_upll_setrate(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - - rate = s3c2440_camif_upll_round(clk, rate); - - camdivn &= ~(S3C2440_CAMDIVN_CAMCLK_SEL | S3C2440_CAMDIVN_CAMCLK_MASK); - - if (rate != parent_rate) { - camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; - camdivn |= (((parent_rate / rate) / 2) - 1); - } - - __raw_writel(camdivn, S3C2440_CAMDIVN); - - return 0; -} - -static unsigned long s3c2440_camif_upll_getrate(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - - if (!(camdivn & S3C2440_CAMDIVN_CAMCLK_SEL)) - return parent_rate; - - camdivn &= S3C2440_CAMDIVN_CAMCLK_MASK; - - return parent_rate / (camdivn + 1) / 2; -} - -/* Extra S3C2440 clocks */ - -static struct clk s3c2440_clk_cam = { - .name = "camif", - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2440_CLKCON_CAMERA, -}; - -static struct clk s3c2440_clk_cam_upll = { - .name = "camif-upll", - .ops = &(struct clk_ops) { - .set_rate = s3c2440_camif_upll_setrate, - .get_rate = s3c2440_camif_upll_getrate, - .round_rate = s3c2440_camif_upll_round, - }, -}; - -static struct clk s3c2440_clk_ac97 = { - .name = "ac97", - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2440_CLKCON_AC97, -}; - -#define S3C24XX_VA_UART0 (S3C_VA_UART) -#define S3C24XX_VA_UART1 (S3C_VA_UART + 0x4000 ) -#define S3C24XX_VA_UART2 (S3C_VA_UART + 0x8000 ) -#define S3C24XX_VA_UART3 (S3C_VA_UART + 0xC000 ) - -static unsigned long s3c2440_fclk_n_getrate(struct clk *clk) -{ - unsigned long ucon0, ucon1, ucon2, divisor; - - /* the fun of calculating the uart divisors on the s3c2440 */ - ucon0 = __raw_readl(S3C24XX_VA_UART0 + S3C2410_UCON); - ucon1 = __raw_readl(S3C24XX_VA_UART1 + S3C2410_UCON); - ucon2 = __raw_readl(S3C24XX_VA_UART2 + S3C2410_UCON); - - ucon0 &= S3C2440_UCON0_DIVMASK; - ucon1 &= S3C2440_UCON1_DIVMASK; - ucon2 &= S3C2440_UCON2_DIVMASK; - - if (ucon0 != 0) - divisor = (ucon0 >> S3C2440_UCON_DIVSHIFT) + 6; - else if (ucon1 != 0) - divisor = (ucon1 >> S3C2440_UCON_DIVSHIFT) + 21; - else if (ucon2 != 0) - divisor = (ucon2 >> S3C2440_UCON_DIVSHIFT) + 36; - else - /* manual calims 44, seems to be 9 */ - divisor = 9; - - return clk_get_rate(clk->parent) / divisor; -} - -static struct clk s3c2440_clk_fclk_n = { - .name = "fclk_n", - .parent = &clk_f, - .ops = &(struct clk_ops) { - .get_rate = s3c2440_fclk_n_getrate, - }, -}; - -static struct clk_lookup s3c2440_clk_lookup[] = { - CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk), - CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p), - CLKDEV_INIT(NULL, "clk_uart_baud3", &s3c2440_clk_fclk_n), - CLKDEV_INIT("s3c2440-uart.0", "uart", &s3c24xx_clk_uart0), - CLKDEV_INIT("s3c2440-uart.1", "uart", &s3c24xx_clk_uart1), - CLKDEV_INIT("s3c2440-uart.2", "uart", &s3c24xx_clk_uart2), - CLKDEV_INIT("s3c2440-camif", "camera", &s3c2440_clk_cam_upll), -}; - -static int __init_refok s3c2440_clk_add(struct device *dev, struct subsys_interface *sif) -{ - struct clk *clock_upll; - struct clk *clock_h; - struct clk *clock_p; - - clock_p = clk_get(NULL, "pclk"); - clock_h = clk_get(NULL, "hclk"); - clock_upll = clk_get(NULL, "upll"); - - if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) { - printk(KERN_ERR "S3C2440: Failed to get parent clocks\n"); - return -EINVAL; - } - - s3c2440_clk_cam.parent = clock_h; - s3c2440_clk_ac97.parent = clock_p; - s3c2440_clk_cam_upll.parent = clock_upll; - s3c24xx_register_clock(&s3c2440_clk_fclk_n); - - s3c24xx_register_clock(&s3c2440_clk_ac97); - s3c24xx_register_clock(&s3c2440_clk_cam); - s3c24xx_register_clock(&s3c2440_clk_cam_upll); - clkdev_add_table(s3c2440_clk_lookup, ARRAY_SIZE(s3c2440_clk_lookup)); - - clk_disable(&s3c2440_clk_ac97); - clk_disable(&s3c2440_clk_cam); - - return 0; -} - -static struct subsys_interface s3c2440_clk_interface = { - .name = "s3c2440_clk", - .subsys = &s3c2440_subsys, - .add_dev = s3c2440_clk_add, -}; - -static __init int s3c24xx_clk_init(void) -{ - return subsys_interface_register(&s3c2440_clk_interface); -} - -arch_initcall(s3c24xx_clk_init); diff --git a/arch/arm/mach-s3c24xx/clock-s3c2443.c b/arch/arm/mach-s3c24xx/clock-s3c2443.c deleted file mode 100644 index 76cd31f7804e..000000000000 --- a/arch/arm/mach-s3c24xx/clock-s3c2443.c +++ /dev/null @@ -1,212 +0,0 @@ -/* linux/arch/arm/mach-s3c2443/clock.c - * - * Copyright (c) 2007, 2010 Simtec Electronics - * Ben Dooks <ben@simtec.co.uk> - * - * S3C2443 Clock control support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include <linux/init.h> - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/list.h> -#include <linux/errno.h> -#include <linux/err.h> -#include <linux/device.h> -#include <linux/clk.h> -#include <linux/mutex.h> -#include <linux/serial_core.h> -#include <linux/io.h> - -#include <asm/mach/map.h> - -#include <mach/hardware.h> - -#include <mach/regs-s3c2443-clock.h> - -#include <plat/cpu-freq.h> - -#include <plat/clock.h> -#include <plat/clock-clksrc.h> -#include <plat/cpu.h> - -/* We currently have to assume that the system is running - * from the XTPll input, and that all ***REFCLKs are being - * fed from it, as we cannot read the state of OM[4] from - * software. - * - * It would be possible for each board initialisation to - * set the correct muxing at initialisation -*/ - -/* clock selections */ - -/* armdiv - * - * this clock is sourced from msysclk and can have a number of - * divider values applied to it to then be fed into armclk. - * The real clock definition is done in s3c2443-clock.c, - * only the armdiv divisor table must be defined here. -*/ - -static unsigned int armdiv[16] = { - [S3C2443_CLKDIV0_ARMDIV_1 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 1, - [S3C2443_CLKDIV0_ARMDIV_2 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 2, - [S3C2443_CLKDIV0_ARMDIV_3 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 3, - [S3C2443_CLKDIV0_ARMDIV_4 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 4, - [S3C2443_CLKDIV0_ARMDIV_6 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 6, - [S3C2443_CLKDIV0_ARMDIV_8 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 8, - [S3C2443_CLKDIV0_ARMDIV_12 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 12, - [S3C2443_CLKDIV0_ARMDIV_16 >> S3C2443_CLKDIV0_ARMDIV_SHIFT] = 16, -}; - -/* hsspi - * - * high-speed spi clock, sourced from esysclk -*/ - -static struct clksrc_clk clk_hsspi = { - .clk = { - .name = "hsspi-if", - .parent = &clk_esysclk.clk, - .ctrlbit = S3C2443_SCLKCON_HSSPICLK, - .enable = s3c2443_clkcon_enable_s, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 4 }, -}; - - -/* clk_hsmcc_div - * - * this clock is sourced from epll, and is fed through a divider, - * to a mux controlled by sclkcon where either it or a extclk can - * be fed to the hsmmc block -*/ - -static struct clksrc_clk clk_hsmmc_div = { - .clk = { - .name = "hsmmc-div", - .devname = "s3c-sdhci.1", - .parent = &clk_esysclk.clk, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 6 }, -}; - -static int s3c2443_setparent_hsmmc(struct clk *clk, struct clk *parent) -{ - unsigned long clksrc = __raw_readl(S3C2443_SCLKCON); - - clksrc &= ~(S3C2443_SCLKCON_HSMMCCLK_EXT | - S3C2443_SCLKCON_HSMMCCLK_EPLL); - - if (parent == &clk_epll) - clksrc |= S3C2443_SCLKCON_HSMMCCLK_EPLL; - else if (parent == &clk_ext) - clksrc |= S3C2443_SCLKCON_HSMMCCLK_EXT; - else - return -EINVAL; - - if (clk->usage > 0) { - __raw_writel(clksrc, S3C2443_SCLKCON); - } - - clk->parent = parent; - return 0; -} - -static int s3c2443_enable_hsmmc(struct clk *clk, int enable) -{ - return s3c2443_setparent_hsmmc(clk, clk->parent); -} - -static struct clk clk_hsmmc = { - .name = "hsmmc-if", - .devname = "s3c-sdhci.1", - .parent = &clk_hsmmc_div.clk, - .enable = s3c2443_enable_hsmmc, - .ops = &(struct clk_ops) { - .set_parent = s3c2443_setparent_hsmmc, - }, -}; - -/* standard clock definitions */ - -static struct clk init_clocks_off[] = { - { - .name = "sdi", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_SDI, - }, { - .name = "spi", - .devname = "s3c2410-spi.0", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_SPI1, - } -}; - -/* clocks to add straight away */ - -static struct clksrc_clk *clksrcs[] __initdata = { - &clk_hsspi, - &clk_hsmmc_div, -}; - -static struct clk *clks[] __initdata = { - &clk_hsmmc, -}; - -static struct clk_lookup s3c2443_clk_lookup[] = { - CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_hsmmc), - CLKDEV_INIT("s3c2443-spi.0", "spi_busclk2", &clk_hsspi.clk), -}; - -void __init s3c2443_init_clocks(int xtal) -{ - unsigned long epllcon = __raw_readl(S3C2443_EPLLCON); - int ptr; - - clk_epll.rate = s3c2443_get_epll(epllcon, xtal); - clk_epll.parent = &clk_epllref.clk; - - s3c2443_common_init_clocks(xtal, s3c2443_get_mpll, - armdiv, ARRAY_SIZE(armdiv), - S3C2443_CLKDIV0_ARMDIV_MASK); - - s3c24xx_register_clocks(clks, ARRAY_SIZE(clks)); - - for (ptr = 0; ptr < ARRAY_SIZE(clksrcs); ptr++) - s3c_register_clksrc(clksrcs[ptr], 1); - - /* We must be careful disabling the clocks we are not intending to - * be using at boot time, as subsystems such as the LCD which do - * their own DMA requests to the bus can cause the system to lockup - * if they where in the middle of requesting bus access. - * - * Disabling the LCD clock if the LCD is active is very dangerous, - * and therefore the bootloader should be careful to not enable - * the LCD clock if it is not needed. - */ - - /* install (and disable) the clocks we do not need immediately */ - - s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off)); - s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off)); - clkdev_add_table(s3c2443_clk_lookup, ARRAY_SIZE(s3c2443_clk_lookup)); -} diff --git a/arch/arm/mach-s3c24xx/clock-s3c244x.c b/arch/arm/mach-s3c24xx/clock-s3c244x.c deleted file mode 100644 index 6d9b688c442b..000000000000 --- a/arch/arm/mach-s3c24xx/clock-s3c244x.c +++ /dev/null @@ -1,141 +0,0 @@ -/* linux/arch/arm/plat-s3c24xx/s3c24xx-clock.c - * - * Copyright (c) 2004-2008 Simtec Electronics - * http://armlinux.simtec.co.uk/ - * Ben Dooks <ben@simtec.co.uk> - * - * S3C2440/S3C2442 Common clock support - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -*/ - -#include <linux/init.h> -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/list.h> -#include <linux/errno.h> -#include <linux/err.h> -#include <linux/device.h> -#include <linux/interrupt.h> -#include <linux/ioport.h> -#include <linux/clk.h> -#include <linux/io.h> - -#include <mach/hardware.h> -#include <linux/atomic.h> -#include <asm/irq.h> - -#include <mach/regs-clock.h> - -#include <plat/clock.h> -#include <plat/cpu.h> - -static int s3c2440_setparent_armclk(struct clk *clk, struct clk *parent) -{ - unsigned long camdivn; - unsigned long dvs; - - if (parent == &clk_f) - dvs = 0; - else if (parent == &clk_h) - dvs = S3C2440_CAMDIVN_DVSEN; - else - return -EINVAL; - - clk->parent = parent; - - camdivn = __raw_readl(S3C2440_CAMDIVN); - camdivn &= ~S3C2440_CAMDIVN_DVSEN; - camdivn |= dvs; - __raw_writel(camdivn, S3C2440_CAMDIVN); - - return 0; -} - -static struct clk clk_arm = { - .name = "armclk", - .id = -1, - .ops = &(struct clk_ops) { - .set_parent = s3c2440_setparent_armclk, - }, -}; - -static int s3c244x_clk_add(struct device *dev, struct subsys_interface *sif) -{ - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - unsigned long clkdivn; - struct clk *clock_upll; - int ret; - - printk("S3C244X: Clock Support, DVS %s\n", - (camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off"); - - clk_arm.parent = (camdivn & S3C2440_CAMDIVN_DVSEN) ? &clk_h : &clk_f; - - ret = s3c24xx_register_clock(&clk_arm); - if (ret < 0) { - printk(KERN_ERR "S3C24XX: Failed to add armclk (%d)\n", ret); - return ret; - } - - clock_upll = clk_get(NULL, "upll"); - if (IS_ERR(clock_upll)) { - printk(KERN_ERR "S3C244X: Failed to get upll clock\n"); - return -ENOENT; - } - - /* check rate of UPLL, and if it is near 96MHz, then change - * to using half the UPLL rate for the system */ - - if (clk_get_rate(clock_upll) > (94 * MHZ)) { - clk_usb_bus.rate = clk_get_rate(clock_upll) / 2; - - spin_lock(&clocks_lock); - - clkdivn = __raw_readl(S3C2410_CLKDIVN); - clkdivn |= S3C2440_CLKDIVN_UCLK; - __raw_writel(clkdivn, S3C2410_CLKDIVN); - - spin_unlock(&clocks_lock); - } - - return 0; -} - -static struct subsys_interface s3c2440_clk_interface = { - .name = "s3c2440_clk", - .subsys = &s3c2440_subsys, - .add_dev = s3c244x_clk_add, -}; - -static int s3c2440_clk_init(void) -{ - return subsys_interface_register(&s3c2440_clk_interface); -} - -arch_initcall(s3c2440_clk_init); - -static struct subsys_interface s3c2442_clk_interface = { - .name = "s3c2442_clk", - .subsys = &s3c2442_subsys, - .add_dev = s3c244x_clk_add, -}; - -static int s3c2442_clk_init(void) -{ - return subsys_interface_register(&s3c2442_clk_interface); -} - -arch_initcall(s3c2442_clk_init); diff --git a/arch/arm/mach-s3c24xx/common-s3c2443.c b/arch/arm/mach-s3c24xx/common-s3c2443.c deleted file mode 100644 index 65d3eef73090..000000000000 --- a/arch/arm/mach-s3c24xx/common-s3c2443.c +++ /dev/null @@ -1,675 +0,0 @@ -/* - * Common code for SoCs starting with the S3C2443 - * - * Copyright (c) 2007, 2010 Simtec Electronics - * Ben Dooks <ben@simtec.co.uk> - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -#include <linux/init.h> -#include <linux/clk.h> -#include <linux/io.h> - -#include <mach/regs-s3c2443-clock.h> - -#include <plat/clock.h> -#include <plat/clock-clksrc.h> -#include <plat/cpu.h> - -#include <plat/cpu-freq.h> - - -static int s3c2443_gate(void __iomem *reg, struct clk *clk, int enable) -{ - u32 ctrlbit = clk->ctrlbit; - u32 con = __raw_readl(reg); - - if (enable) - con |= ctrlbit; - else - con &= ~ctrlbit; - - __raw_writel(con, reg); - return 0; -} - -int s3c2443_clkcon_enable_h(struct clk *clk, int enable) -{ - return s3c2443_gate(S3C2443_HCLKCON, clk, enable); -} - -int s3c2443_clkcon_enable_p(struct clk *clk, int enable) -{ - return s3c2443_gate(S3C2443_PCLKCON, clk, enable); -} - -int s3c2443_clkcon_enable_s(struct clk *clk, int enable) -{ - return s3c2443_gate(S3C2443_SCLKCON, clk, enable); -} - -/* mpllref is a direct descendant of clk_xtal by default, but it is not - * elided as the EPLL can be either sourced by the XTAL or EXTCLK and as - * such directly equating the two source clocks is impossible. - */ -static struct clk clk_mpllref = { - .name = "mpllref", - .parent = &clk_xtal, -}; - -static struct clk *clk_epllref_sources[] = { - [0] = &clk_mpllref, - [1] = &clk_mpllref, - [2] = &clk_xtal, - [3] = &clk_ext, -}; - -struct clksrc_clk clk_epllref = { - .clk = { - .name = "epllref", - }, - .sources = &(struct clksrc_sources) { - .sources = clk_epllref_sources, - .nr_sources = ARRAY_SIZE(clk_epllref_sources), - }, - .reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 7 }, -}; - -/* esysclk - * - * this is sourced from either the EPLL or the EPLLref clock -*/ - -static struct clk *clk_sysclk_sources[] = { - [0] = &clk_epllref.clk, - [1] = &clk_epll, -}; - -struct clksrc_clk clk_esysclk = { - .clk = { - .name = "esysclk", - .parent = &clk_epll, - }, - .sources = &(struct clksrc_sources) { - .sources = clk_sysclk_sources, - .nr_sources = ARRAY_SIZE(clk_sysclk_sources), - }, - .reg_src = { .reg = S3C2443_CLKSRC, .size = 1, .shift = 6 }, -}; - -static unsigned long s3c2443_getrate_mdivclk(struct clk *clk) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long div = __raw_readl(S3C2443_CLKDIV0); - - div &= S3C2443_CLKDIV0_EXTDIV_MASK; - div >>= (S3C2443_CLKDIV0_EXTDIV_SHIFT-1); /* x2 */ - - return parent_rate / (div + 1); -} - -static struct clk clk_mdivclk = { - .name = "mdivclk", - .parent = &clk_mpllref, - .ops = &(struct clk_ops) { - .get_rate = s3c2443_getrate_mdivclk, - }, -}; - -static struct clk *clk_msysclk_sources[] = { - [0] = &clk_mpllref, - [1] = &clk_mpll, - [2] = &clk_mdivclk, - [3] = &clk_mpllref, -}; - -static struct clksrc_clk clk_msysclk = { - .clk = { - .name = "msysclk", - .parent = &clk_xtal, - }, - .sources = &(struct clksrc_sources) { - .sources = clk_msysclk_sources, - .nr_sources = ARRAY_SIZE(clk_msysclk_sources), - }, - .reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 3 }, -}; - -/* prediv - * - * this divides the msysclk down to pass to h/p/etc. - */ - -static unsigned long s3c2443_prediv_getrate(struct clk *clk) -{ - unsigned long rate = clk_get_rate(clk->parent); - unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0); - - clkdiv0 &= S3C2443_CLKDIV0_PREDIV_MASK; - clkdiv0 >>= S3C2443_CLKDIV0_PREDIV_SHIFT; - - return rate / (clkdiv0 + 1); -} - -static struct clk clk_prediv = { - .name = "prediv", - .parent = &clk_msysclk.clk, - .ops = &(struct clk_ops) { - .get_rate = s3c2443_prediv_getrate, - }, -}; - -/* hclk divider - * - * divides the prediv and provides the hclk. - */ - -static unsigned long s3c2443_hclkdiv_getrate(struct clk *clk) -{ - unsigned long rate = clk_get_rate(clk->parent); - unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0); - - clkdiv0 &= S3C2443_CLKDIV0_HCLKDIV_MASK; - - return rate / (clkdiv0 + 1); -} - -static struct clk_ops clk_h_ops = { - .get_rate = s3c2443_hclkdiv_getrate, -}; - -/* pclk divider - * - * divides the hclk and provides the pclk. - */ - -static unsigned long s3c2443_pclkdiv_getrate(struct clk *clk) -{ - unsigned long rate = clk_get_rate(clk->parent); - unsigned long clkdiv0 = __raw_readl(S3C2443_CLKDIV0); - - clkdiv0 = ((clkdiv0 & S3C2443_CLKDIV0_HALF_PCLK) ? 1 : 0); - - return rate / (clkdiv0 + 1); -} - -static struct clk_ops clk_p_ops = { - .get_rate = s3c2443_pclkdiv_getrate, -}; - -/* armdiv - * - * this clock is sourced from msysclk and can have a number of - * divider values applied to it to then be fed into armclk. -*/ - -static unsigned int *armdiv; -static int nr_armdiv; -static int armdivmask; - -static unsigned long s3c2443_armclk_roundrate(struct clk *clk, - unsigned long rate) -{ - unsigned long parent = clk_get_rate(clk->parent); - unsigned long calc; - unsigned best = 256; /* bigger than any value */ - unsigned div; - int ptr; - - if (!nr_armdiv) - return -EINVAL; - - for (ptr = 0; ptr < nr_armdiv; ptr++) { - div = armdiv[ptr]; - if (div) { - /* cpufreq provides 266mhz as 266666000 not 266666666 */ - calc = (parent / div / 1000) * 1000; - if (calc <= rate && div < best) - best = div; - } - } - - return parent / best; -} - -static unsigned long s3c2443_armclk_getrate(struct clk *clk) -{ - unsigned long rate = clk_get_rate(clk->parent); - unsigned long clkcon0; - int val; - - if (!nr_armdiv || !armdivmask) - return -EINVAL; - - clkcon0 = __raw_readl(S3C2443_CLKDIV0); - clkcon0 &= armdivmask; - val = clkcon0 >> S3C2443_CLKDIV0_ARMDIV_SHIFT; - - return rate / armdiv[val]; -} - -static int s3c2443_armclk_setrate(struct clk *clk, unsigned long rate) -{ - unsigned long parent = clk_get_rate(clk->parent); - unsigned long calc; - unsigned div; - unsigned best = 256; /* bigger than any value */ - int ptr; - int val = -1; - - if (!nr_armdiv || !armdivmask) - return -EINVAL; - - for (ptr = 0; ptr < nr_armdiv; ptr++) { - div = armdiv[ptr]; - if (div) { - /* cpufreq provides 266mhz as 266666000 not 266666666 */ - calc = (parent / div / 1000) * 1000; - if (calc <= rate && div < best) { - best = div; - val = ptr; - } - } - } - - if (val >= 0) { - unsigned long clkcon0; - - clkcon0 = __raw_readl(S3C2443_CLKDIV0); - clkcon0 &= ~armdivmask; - clkcon0 |= val << S3C2443_CLKDIV0_ARMDIV_SHIFT; - __raw_writel(clkcon0, S3C2443_CLKDIV0); - } - - return (val == -1) ? -EINVAL : 0; -} - -static struct clk clk_armdiv = { - .name = "armdiv", - .parent = &clk_msysclk.clk, - .ops = &(struct clk_ops) { - .round_rate = s3c2443_armclk_roundrate, - .get_rate = s3c2443_armclk_getrate, - .set_rate = s3c2443_armclk_setrate, - }, -}; - -/* armclk - * - * this is the clock fed into the ARM core itself, from armdiv or from hclk. - */ - -static struct clk *clk_arm_sources[] = { - [0] = &clk_armdiv, - [1] = &clk_h, -}; - -static struct clksrc_clk clk_arm = { - .clk = { - .name = "armclk", - }, - .sources = &(struct clksrc_sources) { - .sources = clk_arm_sources, - .nr_sources = ARRAY_SIZE(clk_arm_sources), - }, - .reg_src = { .reg = S3C2443_CLKDIV0, .size = 1, .shift = 13 }, -}; - -/* usbhost - * - * usb host bus-clock, usually 48MHz to provide USB bus clock timing -*/ - -static struct clksrc_clk clk_usb_bus_host = { - .clk = { - .name = "usb-bus-host-parent", - .parent = &clk_esysclk.clk, - .ctrlbit = S3C2443_SCLKCON_USBHOST, - .enable = s3c2443_clkcon_enable_s, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 2, .shift = 4 }, -}; - -/* common clksrc clocks */ - -static struct clksrc_clk clksrc_clks[] = { - { - /* camera interface bus-clock, divided down from esysclk */ - .clk = { - .name = "camif-upll", /* same as 2440 name */ - .parent = &clk_esysclk.clk, - .ctrlbit = S3C2443_SCLKCON_CAMCLK, - .enable = s3c2443_clkcon_enable_s, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 26 }, - }, { - .clk = { - .name = "display-if", - .parent = &clk_esysclk.clk, - .ctrlbit = S3C2443_SCLKCON_DISPCLK, - .enable = s3c2443_clkcon_enable_s, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 8, .shift = 16 }, - }, -}; - -static struct clksrc_clk clk_esys_uart = { - /* ART baud-rate clock sourced from esysclk via a divisor */ - .clk = { - .name = "uartclk", - .parent = &clk_esysclk.clk, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 8 }, -}; - -static struct clk clk_i2s_ext = { - .name = "i2s-ext", -}; - -/* i2s_eplldiv - * - * This clock is the output from the I2S divisor of ESYSCLK, and is separate - * from the mux that comes after it (cannot merge into one single clock) -*/ - -static struct clksrc_clk clk_i2s_eplldiv = { - .clk = { - .name = "i2s-eplldiv", - .parent = &clk_esysclk.clk, - }, - .reg_div = { .reg = S3C2443_CLKDIV1, .size = 4, .shift = 12, }, -}; - -/* i2s-ref - * - * i2s bus reference clock, selectable from external, esysclk or epllref - * - * Note, this used to be two clocks, but was compressed into one. -*/ - -static struct clk *clk_i2s_srclist[] = { - [0] = &clk_i2s_eplldiv.clk, - [1] = &clk_i2s_ext, - [2] = &clk_epllref.clk, - [3] = &clk_epllref.clk, -}; - -static struct clksrc_clk clk_i2s = { - .clk = { - .name = "i2s-if", - .ctrlbit = S3C2443_SCLKCON_I2SCLK, - .enable = s3c2443_clkcon_enable_s, - - }, - .sources = &(struct clksrc_sources) { - .sources = clk_i2s_srclist, - .nr_sources = ARRAY_SIZE(clk_i2s_srclist), - }, - .reg_src = { .reg = S3C2443_CLKSRC, .size = 2, .shift = 14 }, -}; - -static struct clk init_clocks_off[] = { - { - .name = "iis", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_IIS, - }, { - .name = "adc", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_ADC, - }, { - .name = "i2c", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_IIC, - } -}; - -static struct clk init_clocks[] = { - { - .name = "dma.0", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_DMA0, - }, { - .name = "dma.1", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_DMA1, - }, { - .name = "dma.2", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_DMA2, - }, { - .name = "dma.3", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_DMA3, - }, { - .name = "dma.4", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_DMA4, - }, { - .name = "dma.5", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_DMA5, - }, { - .name = "gpio", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_GPIO, - }, { - .name = "usb-host", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_USBH, - }, { - .name = "usb-device", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_USBD, - }, { - .name = "lcd", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_LCDC, - - }, { - .name = "timers", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_PWMT, - }, { - .name = "cfc", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_CFC, - }, { - .name = "ssmc", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_SSMC, - }, { - .name = "uart", - .devname = "s3c2440-uart.0", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_UART0, - }, { - .name = "uart", - .devname = "s3c2440-uart.1", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_UART1, - }, { - .name = "uart", - .devname = "s3c2440-uart.2", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_UART2, - }, { - .name = "uart", - .devname = "s3c2440-uart.3", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_UART3, - }, { - .name = "rtc", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_RTC, - }, { - .name = "watchdog", - .parent = &clk_p, - .ctrlbit = S3C2443_PCLKCON_WDT, - }, { - .name = "ac97", - .parent = &clk_p, - .ctrlbit = S3C2443_PCLKCON_AC97, - }, { - .name = "nand", - .parent = &clk_h, - }, { - .name = "usb-bus-host", - .parent = &clk_usb_bus_host.clk, - } -}; - -static struct clk hsmmc1_clk = { - .name = "hsmmc", - .devname = "s3c-sdhci.1", - .parent = &clk_h, - .enable = s3c2443_clkcon_enable_h, - .ctrlbit = S3C2443_HCLKCON_HSMMC, -}; - -static struct clk hsspi_clk = { - .name = "spi", - .devname = "s3c2443-spi.0", - .parent = &clk_p, - .enable = s3c2443_clkcon_enable_p, - .ctrlbit = S3C2443_PCLKCON_HSSPI, -}; - -/* EPLLCON compatible enough to get on/off information */ - -void __init_or_cpufreq s3c2443_common_setup_clocks(pll_fn get_mpll) -{ - unsigned long epllcon = __raw_readl(S3C2443_EPLLCON); - unsigned long mpllcon = __raw_readl(S3C2443_MPLLCON); - struct clk *xtal_clk; - unsigned long xtal; - unsigned long pll; - int ptr; - - xtal_clk = clk_get(NULL, "xtal"); - xtal = clk_get_rate(xtal_clk); - clk_put(xtal_clk); - - pll = get_mpll(mpllcon, xtal); - clk_msysclk.clk.rate = pll; - clk_mpll.rate = pll; - - printk("CPU: MPLL %s %ld.%03ld MHz, cpu %ld.%03ld MHz, mem %ld.%03ld MHz, pclk %ld.%03ld MHz\n", - (mpllcon & S3C2443_PLLCON_OFF) ? "off" : "on", - print_mhz(pll), print_mhz(clk_get_rate(&clk_armdiv)), - print_mhz(clk_get_rate(&clk_h)), - print_mhz(clk_get_rate(&clk_p))); - - for (ptr = 0; ptr < ARRAY_SIZE(clksrc_clks); ptr++) - s3c_set_clksrc(&clksrc_clks[ptr], true); - - /* ensure usb bus clock is within correct rate of 48MHz */ - - if (clk_get_rate(&clk_usb_bus_host.clk) != (48 * 1000 * 1000)) { - printk(KERN_INFO "Warning: USB host bus not at 48MHz\n"); - clk_set_rate(&clk_usb_bus_host.clk, 48*1000*1000); - } - - printk("CPU: EPLL %s %ld.%03ld MHz, usb-bus %ld.%03ld MHz\n", - (epllcon & S3C2443_PLLCON_OFF) ? "off" : "on", - print_mhz(clk_get_rate(&clk_epll)), - print_mhz(clk_get_rate(&clk_usb_bus))); -} - -static struct clk *clks[] __initdata = { - &clk_prediv, - &clk_mpllref, - &clk_mdivclk, - &clk_ext, - &clk_epll, - &clk_usb_bus, - &clk_armdiv, - &hsmmc1_clk, - &hsspi_clk, -}; - -static struct clksrc_clk *clksrcs[] __initdata = { - &clk_i2s_eplldiv, - &clk_i2s, - &clk_usb_bus_host, - &clk_epllref, - &clk_esysclk, - &clk_msysclk, - &clk_arm, -}; - -static struct clk_lookup s3c2443_clk_lookup[] = { - CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk), - CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p), - CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_esys_uart.clk), - CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &hsmmc1_clk), - CLKDEV_INIT("s3c2443-spi.0", "spi_busclk0", &hsspi_clk), -}; - -void __init s3c2443_common_init_clocks(int xtal, pll_fn get_mpll, - unsigned int *divs, int nr_divs, - int divmask) -{ - int ptr; - - armdiv = divs; - nr_armdiv = nr_divs; - armdivmask = divmask; - - /* s3c2443 parents h clock from prediv */ - clk_h.parent = &clk_prediv; - clk_h.ops = &clk_h_ops; - - /* and p clock from h clock */ - clk_p.parent = &clk_h; - clk_p.ops = &clk_p_ops; - - clk_usb_bus.parent = &clk_usb_bus_host.clk; - clk_epll.parent = &clk_epllref.clk; - - s3c24xx_register_baseclocks(xtal); - s3c24xx_register_clocks(clks, ARRAY_SIZE(clks)); - - for (ptr = 0; ptr < ARRAY_SIZE(clksrcs); ptr++) - s3c_register_clksrc(clksrcs[ptr], 1); - - s3c_register_clksrc(clksrc_clks, ARRAY_SIZE(clksrc_clks)); - s3c_register_clocks(init_clocks, ARRAY_SIZE(init_clocks)); - - /* See s3c2443/etc notes on disabling clocks at init time */ - s3c_register_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off)); - s3c_disable_clocks(init_clocks_off, ARRAY_SIZE(init_clocks_off)); - clkdev_add_table(s3c2443_clk_lookup, ARRAY_SIZE(s3c2443_clk_lookup)); - - s3c2443_common_setup_clocks(get_mpll); -} diff --git a/arch/arm/mach-s3c24xx/common.c b/arch/arm/mach-s3c24xx/common.c index 1bc8e73c94f9..c0763b837745 100644 --- a/arch/arm/mach-s3c24xx/common.c +++ b/arch/arm/mach-s3c24xx/common.c @@ -53,6 +53,7 @@ #include <plat/cpu-freq.h> #include <plat/pll.h> #include <plat/pwm-core.h> +#include <plat/watchdog-reset.h> #include "common.h" @@ -73,7 +74,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32410000, .idmask = 0xffffffff, .map_io = s3c2410_map_io, - .init_clocks = s3c2410_init_clocks, .init_uarts = s3c2410_init_uarts, .init = s3c2410_init, .name = name_s3c2410 @@ -82,7 +82,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32410002, .idmask = 0xffffffff, .map_io = s3c2410_map_io, - .init_clocks = s3c2410_init_clocks, .init_uarts = s3c2410_init_uarts, .init = s3c2410a_init, .name = name_s3c2410a @@ -91,7 +90,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32440000, .idmask = 0xffffffff, .map_io = s3c2440_map_io, - .init_clocks = s3c244x_init_clocks, .init_uarts = s3c244x_init_uarts, .init = s3c2440_init, .name = name_s3c2440 @@ -100,7 +98,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32440001, .idmask = 0xffffffff, .map_io = s3c2440_map_io, - .init_clocks = s3c244x_init_clocks, .init_uarts = s3c244x_init_uarts, .init = s3c2440_init, .name = name_s3c2440a @@ -109,7 +106,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32440aaa, .idmask = 0xffffffff, .map_io = s3c2442_map_io, - .init_clocks = s3c244x_init_clocks, .init_uarts = s3c244x_init_uarts, .init = s3c2442_init, .name = name_s3c2442 @@ -118,7 +114,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32440aab, .idmask = 0xffffffff, .map_io = s3c2442_map_io, - .init_clocks = s3c244x_init_clocks, .init_uarts = s3c244x_init_uarts, .init = s3c2442_init, .name = name_s3c2442b @@ -127,7 +122,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32412001, .idmask = 0xffffffff, .map_io = s3c2412_map_io, - .init_clocks = s3c2412_init_clocks, .init_uarts = s3c2412_init_uarts, .init = s3c2412_init, .name = name_s3c2412, @@ -136,7 +130,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32412003, .idmask = 0xffffffff, .map_io = s3c2412_map_io, - .init_clocks = s3c2412_init_clocks, .init_uarts = s3c2412_init_uarts, .init = s3c2412_init, .name = name_s3c2412, @@ -145,7 +138,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32450003, .idmask = 0xffffffff, .map_io = s3c2416_map_io, - .init_clocks = s3c2416_init_clocks, .init_uarts = s3c2416_init_uarts, .init = s3c2416_init, .name = name_s3c2416, @@ -154,7 +146,6 @@ static struct cpu_table cpu_ids[] __initdata = { .idcode = 0x32443001, .idmask = 0xffffffff, .map_io = s3c2443_map_io, - .init_clocks = s3c2443_init_clocks, .init_uarts = s3c2443_init_uarts, .init = s3c2443_init, .name = name_s3c2443, @@ -316,21 +307,6 @@ struct s3c24xx_uart_resources s3c2410_uart_resources[] __initdata = { }, }; -/* initialise all the clocks */ - -void __init_or_cpufreq s3c24xx_setup_clocks(unsigned long fclk, - unsigned long hclk, - unsigned long pclk) -{ - clk_upll.rate = s3c24xx_get_pll(__raw_readl(S3C2410_UPLLCON), - clk_xtal.rate); - - clk_mpll.rate = fclk; - clk_h.rate = hclk; - clk_p.rate = pclk; - clk_f.rate = fclk; -} - #if defined(CONFIG_CPU_S3C2410) || defined(CONFIG_CPU_S3C2412) || \ defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) static struct resource s3c2410_dma_resource[] = { @@ -534,3 +510,62 @@ struct platform_device s3c2443_device_dma = { }, }; #endif + +#if defined(CONFIG_COMMON_CLK) && defined(CONFIG_CPU_S3C2410) +void __init s3c2410_init_clocks(int xtal) +{ + s3c2410_common_clk_init(NULL, xtal, 0, S3C24XX_VA_CLKPWR); + samsung_wdt_reset_init(S3C24XX_VA_WATCHDOG); +} +#endif + +#ifdef CONFIG_CPU_S3C2412 +void __init s3c2412_init_clocks(int xtal) +{ + s3c2412_common_clk_init(NULL, xtal, 0, S3C24XX_VA_CLKPWR); +} +#endif + +#ifdef CONFIG_CPU_S3C2416 +void __init s3c2416_init_clocks(int xtal) +{ + s3c2443_common_clk_init(NULL, xtal, 0, S3C24XX_VA_CLKPWR); +} +#endif + +#if defined(CONFIG_COMMON_CLK) && defined(CONFIG_CPU_S3C2440) +void __init s3c2440_init_clocks(int xtal) +{ + s3c2410_common_clk_init(NULL, xtal, 1, S3C24XX_VA_CLKPWR); + samsung_wdt_reset_init(S3C24XX_VA_WATCHDOG); +} +#endif + +#if defined(CONFIG_COMMON_CLK) && defined(CONFIG_CPU_S3C2442) +void __init s3c2442_init_clocks(int xtal) +{ + s3c2410_common_clk_init(NULL, xtal, 2, S3C24XX_VA_CLKPWR); + samsung_wdt_reset_init(S3C24XX_VA_WATCHDOG); +} +#endif + +#ifdef CONFIG_CPU_S3C2443 +void __init s3c2443_init_clocks(int xtal) +{ + s3c2443_common_clk_init(NULL, xtal, 1, S3C24XX_VA_CLKPWR); +} +#endif + +#if defined(CONFIG_CPU_S3C2410) || defined(CONFIG_CPU_S3C2440) || \ + defined(CONFIG_CPU_S3C2442) +static struct resource s3c2410_dclk_resource[] = { + [0] = DEFINE_RES_MEM(0x56000084, 0x4), +}; + +struct platform_device s3c2410_device_dclk = { + .name = "s3c2410-dclk", + .id = 0, + .num_resources = ARRAY_SIZE(s3c2410_dclk_resource), + .resource = s3c2410_dclk_resource, +}; +#endif diff --git a/arch/arm/mach-s3c24xx/common.h b/arch/arm/mach-s3c24xx/common.h index e46c10417216..ac3ff12a0601 100644 --- a/arch/arm/mach-s3c24xx/common.h +++ b/arch/arm/mach-s3c24xx/common.h @@ -67,16 +67,15 @@ extern struct syscore_ops s3c2416_irq_syscore_ops; #if defined(CONFIG_CPU_S3C2440) || defined(CONFIG_CPU_S3C2442) extern void s3c244x_map_io(void); extern void s3c244x_init_uarts(struct s3c2410_uartcfg *cfg, int no); -extern void s3c244x_init_clocks(int xtal); extern void s3c244x_restart(enum reboot_mode mode, const char *cmd); #else -#define s3c244x_init_clocks NULL #define s3c244x_init_uarts NULL #endif #ifdef CONFIG_CPU_S3C2440 extern int s3c2440_init(void); extern void s3c2440_map_io(void); +extern void s3c2440_init_clocks(int xtal); extern void s3c2440_init_irq(void); #else #define s3c2440_init NULL @@ -86,6 +85,7 @@ extern void s3c2440_init_irq(void); #ifdef CONFIG_CPU_S3C2442 extern int s3c2442_init(void); extern void s3c2442_map_io(void); +extern void s3c2442_init_clocks(int xtal); extern void s3c2442_init_irq(void); #else #define s3c2442_init NULL @@ -114,4 +114,21 @@ extern struct platform_device s3c2412_device_dma; extern struct platform_device s3c2440_device_dma; extern struct platform_device s3c2443_device_dma; +extern struct platform_device s3c2410_device_dclk; + +#ifdef CONFIG_S3C2410_COMMON_CLK +void __init s3c2410_common_clk_init(struct device_node *np, unsigned long xti_f, + int current_soc, + void __iomem *reg_base); +#endif +#ifdef CONFIG_S3C2412_COMMON_CLK +void __init s3c2412_common_clk_init(struct device_node *np, unsigned long xti_f, + unsigned long ext_f, void __iomem *reg_base); +#endif +#ifdef CONFIG_S3C2443_COMMON_CLK +void __init s3c2443_common_clk_init(struct device_node *np, unsigned long xti_f, + int current_soc, + void __iomem *reg_base); +#endif + #endif /* __ARCH_ARM_MACH_S3C24XX_COMMON_H */ diff --git a/arch/arm/mach-s3c24xx/cpufreq-utils.c b/arch/arm/mach-s3c24xx/cpufreq-utils.c index 2a0aa5684e72..d4d9514335f4 100644 --- a/arch/arm/mach-s3c24xx/cpufreq-utils.c +++ b/arch/arm/mach-s3c24xx/cpufreq-utils.c @@ -14,6 +14,7 @@ #include <linux/errno.h> #include <linux/cpufreq.h> #include <linux/io.h> +#include <linux/clk.h> #include <mach/map.h> #include <mach/regs-clock.h> @@ -60,5 +61,6 @@ void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg) */ void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg) { - __raw_writel(cfg->pll.driver_data, S3C2410_MPLLCON); + if (!IS_ERR(cfg->mpll)) + clk_set_rate(cfg->mpll, cfg->pll.frequency); } diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h b/arch/arm/mach-s3c24xx/include/mach/regs-clock.h index 3415b60082d7..3db6c10de023 100644 --- a/arch/arm/mach-s3c24xx/include/mach/regs-clock.h +++ b/arch/arm/mach-s3c24xx/include/mach/regs-clock.h @@ -42,24 +42,6 @@ #define S3C2410_CLKCON_IIS (1<<17) #define S3C2410_CLKCON_SPI (1<<18) -/* DCLKCON register addresses in gpio.h */ - -#define S3C2410_DCLKCON_DCLK0EN (1<<0) -#define S3C2410_DCLKCON_DCLK0_PCLK (0<<1) -#define S3C2410_DCLKCON_DCLK0_UCLK (1<<1) -#define S3C2410_DCLKCON_DCLK0_DIV(x) (((x) - 1 )<<4) -#define S3C2410_DCLKCON_DCLK0_CMP(x) (((x) - 1 )<<8) -#define S3C2410_DCLKCON_DCLK0_DIV_MASK ((0xf)<<4) -#define S3C2410_DCLKCON_DCLK0_CMP_MASK ((0xf)<<8) - -#define S3C2410_DCLKCON_DCLK1EN (1<<16) -#define S3C2410_DCLKCON_DCLK1_PCLK (0<<17) -#define S3C2410_DCLKCON_DCLK1_UCLK (1<<17) -#define S3C2410_DCLKCON_DCLK1_DIV(x) (((x) - 1) <<20) -#define S3C2410_DCLKCON_DCLK1_CMP(x) (((x) - 1) <<24) -#define S3C2410_DCLKCON_DCLK1_DIV_MASK ((0xf) <<20) -#define S3C2410_DCLKCON_DCLK1_CMP_MASK ((0xf) <<24) - #define S3C2410_CLKDIVN_PDIVN (1<<0) #define S3C2410_CLKDIVN_HDIVN (1<<1) diff --git a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h b/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h index c2ef016032ab..c6583cfa5835 100644 --- a/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h +++ b/arch/arm/mach-s3c24xx/include/mach/regs-gpio.h @@ -457,9 +457,6 @@ /* miscellaneous control */ #define S3C2410_MISCCR S3C2410_GPIOREG(0x80) -#define S3C2410_DCLKCON S3C2410_GPIOREG(0x84) - -#define S3C24XX_DCLKCON S3C24XX_GPIOREG2(0x84) /* see clock.h for dclk definitions */ diff --git a/arch/arm/mach-s3c24xx/mach-amlm5900.c b/arch/arm/mach-s3c24xx/mach-amlm5900.c index 8ac9554aa996..5157e250dd13 100644 --- a/arch/arm/mach-s3c24xx/mach-amlm5900.c +++ b/arch/arm/mach-s3c24xx/mach-amlm5900.c @@ -161,11 +161,16 @@ static struct platform_device *amlm5900_devices[] __initdata = { static void __init amlm5900_map_io(void) { s3c24xx_init_io(amlm5900_iodesc, ARRAY_SIZE(amlm5900_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(amlm5900_uartcfgs, ARRAY_SIZE(amlm5900_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init amlm5900_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + #ifdef CONFIG_FB_S3C2410 static struct s3c2410fb_display __initdata amlm5900_lcd_info = { .width = 160, @@ -241,6 +246,6 @@ MACHINE_START(AML_M5900, "AML_M5900") .map_io = amlm5900_map_io, .init_irq = s3c2410_init_irq, .init_machine = amlm5900_init, - .init_time = samsung_timer_init, + .init_time = amlm5900_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-anubis.c b/arch/arm/mach-s3c24xx/mach-anubis.c index 81a270af2336..e053581cab0b 100644 --- a/arch/arm/mach-s3c24xx/mach-anubis.c +++ b/arch/arm/mach-s3c24xx/mach-anubis.c @@ -46,7 +46,6 @@ #include <net/ax88796.h> -#include <plat/clock.h> #include <plat/devs.h> #include <plat/cpu.h> #include <linux/platform_data/asoc-s3c24xx_simtec.h> @@ -352,6 +351,7 @@ static struct platform_device anubis_device_sm501 = { /* Standard Anubis devices */ static struct platform_device *anubis_devices[] __initdata = { + &s3c2410_device_dclk, &s3c_device_ohci, &s3c_device_wdt, &s3c_device_adc, @@ -364,14 +364,6 @@ static struct platform_device *anubis_devices[] __initdata = { &anubis_device_sm501, }; -static struct clk *anubis_clocks[] __initdata = { - &s3c24xx_dclk0, - &s3c24xx_dclk1, - &s3c24xx_clkout0, - &s3c24xx_clkout1, - &s3c24xx_uclk, -}; - /* I2C devices. */ static struct i2c_board_info anubis_i2c_devs[] __initdata = { @@ -394,23 +386,7 @@ static struct s3c24xx_audio_simtec_pdata __initdata anubis_audio = { static void __init anubis_map_io(void) { - /* initialise the clocks */ - - s3c24xx_dclk0.parent = &clk_upll; - s3c24xx_dclk0.rate = 12*1000*1000; - - s3c24xx_dclk1.parent = &clk_upll; - s3c24xx_dclk1.rate = 24*1000*1000; - - s3c24xx_clkout0.parent = &s3c24xx_dclk0; - s3c24xx_clkout1.parent = &s3c24xx_dclk1; - - s3c24xx_uclk.parent = &s3c24xx_clkout1; - - s3c24xx_register_clocks(anubis_clocks, ARRAY_SIZE(anubis_clocks)); - s3c24xx_init_io(anubis_iodesc, ARRAY_SIZE(anubis_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(anubis_uartcfgs, ARRAY_SIZE(anubis_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); @@ -428,6 +404,12 @@ static void __init anubis_map_io(void) } } +static void __init anubis_init_time(void) +{ + s3c2440_init_clocks(12000000); + samsung_timer_init(); +} + static void __init anubis_init(void) { s3c_i2c0_set_platdata(NULL); @@ -447,6 +429,6 @@ MACHINE_START(ANUBIS, "Simtec-Anubis") .map_io = anubis_map_io, .init_machine = anubis_init, .init_irq = s3c2440_init_irq, - .init_time = samsung_timer_init, + .init_time = anubis_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-at2440evb.c b/arch/arm/mach-s3c24xx/mach-at2440evb.c index d8f6bb1096cb..9db768f448a5 100644 --- a/arch/arm/mach-s3c24xx/mach-at2440evb.c +++ b/arch/arm/mach-s3c24xx/mach-at2440evb.c @@ -45,7 +45,6 @@ #include <linux/mtd/nand_ecc.h> #include <linux/mtd/partitions.h> -#include <plat/clock.h> #include <plat/devs.h> #include <plat/cpu.h> #include <linux/platform_data/mmc-s3cmci.h> @@ -192,11 +191,16 @@ static struct platform_device *at2440evb_devices[] __initdata = { static void __init at2440evb_map_io(void) { s3c24xx_init_io(at2440evb_iodesc, ARRAY_SIZE(at2440evb_iodesc)); - s3c24xx_init_clocks(16934400); s3c24xx_init_uarts(at2440evb_uartcfgs, ARRAY_SIZE(at2440evb_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init at2440evb_init_time(void) +{ + s3c2440_init_clocks(16934400); + samsung_timer_init(); +} + static void __init at2440evb_init(void) { s3c24xx_fb_set_platdata(&at2440evb_fb_info); @@ -213,6 +217,6 @@ MACHINE_START(AT2440EVB, "AT2440EVB") .map_io = at2440evb_map_io, .init_machine = at2440evb_init, .init_irq = s3c2440_init_irq, - .init_time = samsung_timer_init, + .init_time = at2440evb_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-bast.c b/arch/arm/mach-s3c24xx/mach-bast.c index e371ff53a408..f9112b801a33 100644 --- a/arch/arm/mach-s3c24xx/mach-bast.c +++ b/arch/arm/mach-s3c24xx/mach-bast.c @@ -51,7 +51,6 @@ #include <mach/regs-lcd.h> #include <mach/gpio-samsung.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/cpu-freq.h> #include <plat/devs.h> @@ -523,6 +522,7 @@ static struct s3c_hwmon_pdata bast_hwmon_info = { // cat /sys/devices/platform/s3c24xx-adc/s3c-hwmon/in_0 static struct platform_device *bast_devices[] __initdata = { + &s3c2410_device_dclk, &s3c_device_ohci, &s3c_device_lcd, &s3c_device_wdt, @@ -537,14 +537,6 @@ static struct platform_device *bast_devices[] __initdata = { &bast_sio, }; -static struct clk *bast_clocks[] __initdata = { - &s3c24xx_dclk0, - &s3c24xx_dclk1, - &s3c24xx_clkout0, - &s3c24xx_clkout1, - &s3c24xx_uclk, -}; - static struct s3c_cpufreq_board __initdata bast_cpufreq = { .refresh = 7800, /* 7.8usec */ .auto_io = 1, @@ -558,29 +550,19 @@ static struct s3c24xx_audio_simtec_pdata __initdata bast_audio = { static void __init bast_map_io(void) { - /* initialise the clocks */ - - s3c24xx_dclk0.parent = &clk_upll; - s3c24xx_dclk0.rate = 12*1000*1000; - - s3c24xx_dclk1.parent = &clk_upll; - s3c24xx_dclk1.rate = 24*1000*1000; - - s3c24xx_clkout0.parent = &s3c24xx_dclk0; - s3c24xx_clkout1.parent = &s3c24xx_dclk1; - - s3c24xx_uclk.parent = &s3c24xx_clkout1; - - s3c24xx_register_clocks(bast_clocks, ARRAY_SIZE(bast_clocks)); - s3c_hwmon_set_platdata(&bast_hwmon_info); s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(bast_uartcfgs, ARRAY_SIZE(bast_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init bast_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + static void __init bast_init(void) { register_syscore_ops(&bast_pm_syscore_ops); @@ -608,6 +590,6 @@ MACHINE_START(BAST, "Simtec-BAST") .map_io = bast_map_io, .init_irq = s3c2410_init_irq, .init_machine = bast_init, - .init_time = samsung_timer_init, + .init_time = bast_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-gta02.c b/arch/arm/mach-s3c24xx/mach-gta02.c index dc4db849f0fd..fc3a08d0cb3f 100644 --- a/arch/arm/mach-s3c24xx/mach-gta02.c +++ b/arch/arm/mach-s3c24xx/mach-gta02.c @@ -501,7 +501,6 @@ static struct platform_device gta02_buttons_device = { static void __init gta02_map_io(void) { s3c24xx_init_io(gta02_iodesc, ARRAY_SIZE(gta02_iodesc)); - s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(gta02_uartcfgs, ARRAY_SIZE(gta02_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } @@ -585,6 +584,11 @@ static void __init gta02_machine_init(void) regulator_has_full_constraints(); } +static void __init gta02_init_time(void) +{ + s3c2442_init_clocks(12000000); + samsung_timer_init(); +} MACHINE_START(NEO1973_GTA02, "GTA02") /* Maintainer: Nelson Castillo <arhuaco@freaks-unidos.net> */ @@ -592,6 +596,6 @@ MACHINE_START(NEO1973_GTA02, "GTA02") .map_io = gta02_map_io, .init_irq = s3c2442_init_irq, .init_machine = gta02_machine_init, - .init_time = samsung_timer_init, + .init_time = gta02_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c index e453acd92cbf..fbf5487ae5d1 100644 --- a/arch/arm/mach-s3c24xx/mach-h1940.c +++ b/arch/arm/mach-s3c24xx/mach-h1940.c @@ -57,7 +57,6 @@ #include <mach/regs-lcd.h> #include <mach/gpio-samsung.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/devs.h> #include <plat/gpio-cfg.h> @@ -646,7 +645,6 @@ static struct platform_device *h1940_devices[] __initdata = { static void __init h1940_map_io(void) { s3c24xx_init_io(h1940_iodesc, ARRAY_SIZE(h1940_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(h1940_uartcfgs, ARRAY_SIZE(h1940_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); @@ -662,6 +660,12 @@ static void __init h1940_map_io(void) WARN_ON(gpiochip_add(&h1940_latch_gpiochip)); } +static void __init h1940_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + /* H1940 and RX3715 need to reserve this for suspend */ static void __init h1940_reserve(void) { @@ -739,6 +743,6 @@ MACHINE_START(H1940, "IPAQ-H1940") .reserve = h1940_reserve, .init_irq = s3c2410_init_irq, .init_machine = h1940_init, - .init_time = samsung_timer_init, + .init_time = h1940_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-jive.c b/arch/arm/mach-s3c24xx/mach-jive.c index 5faa7239e7d6..e81ea82c55f9 100644 --- a/arch/arm/mach-s3c24xx/mach-jive.c +++ b/arch/arm/mach-s3c24xx/mach-jive.c @@ -507,11 +507,16 @@ static struct syscore_ops jive_pm_syscore_ops = { static void __init jive_map_io(void) { s3c24xx_init_io(jive_iodesc, ARRAY_SIZE(jive_iodesc)); - s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(jive_uartcfgs, ARRAY_SIZE(jive_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init jive_init_time(void) +{ + s3c2412_init_clocks(12000000); + samsung_timer_init(); +} + static void jive_power_off(void) { printk(KERN_INFO "powering system down...\n"); @@ -665,6 +670,6 @@ MACHINE_START(JIVE, "JIVE") .init_irq = s3c2412_init_irq, .map_io = jive_map_io, .init_machine = jive_machine_init, - .init_time = samsung_timer_init, + .init_time = jive_init_time, .restart = s3c2412_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-mini2440.c b/arch/arm/mach-s3c24xx/mach-mini2440.c index 9e57fd9f4f3b..5cc40ec1d254 100644 --- a/arch/arm/mach-s3c24xx/mach-mini2440.c +++ b/arch/arm/mach-s3c24xx/mach-mini2440.c @@ -54,7 +54,6 @@ #include <linux/mtd/partitions.h> #include <plat/gpio-cfg.h> -#include <plat/clock.h> #include <plat/devs.h> #include <plat/cpu.h> #include <plat/samsung-time.h> @@ -525,11 +524,16 @@ static struct platform_device *mini2440_devices[] __initdata = { static void __init mini2440_map_io(void) { s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc)); - s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init mini2440_init_time(void) +{ + s3c2440_init_clocks(12000000); + samsung_timer_init(); +} + /* * mini2440_features string * @@ -690,6 +694,6 @@ MACHINE_START(MINI2440, "MINI2440") .map_io = mini2440_map_io, .init_machine = mini2440_init, .init_irq = s3c2440_init_irq, - .init_time = samsung_timer_init, + .init_time = mini2440_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-n30.c b/arch/arm/mach-s3c24xx/mach-n30.c index 4cccaad34847..3ac2a54348d6 100644 --- a/arch/arm/mach-s3c24xx/mach-n30.c +++ b/arch/arm/mach-s3c24xx/mach-n30.c @@ -45,7 +45,6 @@ #include <linux/platform_data/i2c-s3c2410.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/devs.h> #include <linux/platform_data/mmc-s3cmci.h> @@ -535,11 +534,16 @@ static void __init n30_map_io(void) { s3c24xx_init_io(n30_iodesc, ARRAY_SIZE(n30_iodesc)); n30_hwinit(); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init n30_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + /* GPB3 is the line that controls the pull-up for the USB D+ line */ static void __init n30_init(void) @@ -591,7 +595,7 @@ MACHINE_START(N30, "Acer-N30") Ben Dooks <ben-linux@fluff.org> */ .atag_offset = 0x100, - .init_time = samsung_timer_init, + .init_time = n30_init_time, .init_machine = n30_init, .init_irq = s3c2410_init_irq, .map_io = n30_map_io, @@ -602,7 +606,7 @@ MACHINE_START(N35, "Acer-N35") /* Maintainer: Christer Weinigel <christer@weinigel.se> */ .atag_offset = 0x100, - .init_time = samsung_timer_init, + .init_time = n30_init_time, .init_machine = n30_init, .init_irq = s3c2410_init_irq, .map_io = n30_map_io, diff --git a/arch/arm/mach-s3c24xx/mach-nexcoder.c b/arch/arm/mach-s3c24xx/mach-nexcoder.c index 3066851f584d..c82c281ce351 100644 --- a/arch/arm/mach-s3c24xx/mach-nexcoder.c +++ b/arch/arm/mach-s3c24xx/mach-nexcoder.c @@ -42,7 +42,6 @@ #include <linux/platform_data/i2c-s3c2410.h> #include <plat/gpio-cfg.h> -#include <plat/clock.h> #include <plat/devs.h> #include <plat/cpu.h> #include <plat/samsung-time.h> @@ -135,13 +134,18 @@ static void __init nexcoder_sensorboard_init(void) static void __init nexcoder_map_io(void) { s3c24xx_init_io(nexcoder_iodesc, ARRAY_SIZE(nexcoder_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(nexcoder_uartcfgs, ARRAY_SIZE(nexcoder_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); nexcoder_sensorboard_init(); } +static void __init nexcoder_init_time(void) +{ + s3c2440_init_clocks(12000000); + samsung_timer_init(); +} + static void __init nexcoder_init(void) { s3c_i2c0_set_platdata(NULL); @@ -154,6 +158,6 @@ MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440") .map_io = nexcoder_map_io, .init_machine = nexcoder_init, .init_irq = s3c2440_init_irq, - .init_time = samsung_timer_init, + .init_time = nexcoder_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-osiris.c b/arch/arm/mach-s3c24xx/mach-osiris.c index a4ae4bb3666d..189147b80eca 100644 --- a/arch/arm/mach-s3c24xx/mach-osiris.c +++ b/arch/arm/mach-s3c24xx/mach-osiris.c @@ -40,7 +40,6 @@ #include <linux/mtd/nand_ecc.h> #include <linux/mtd/partitions.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/cpu-freq.h> #include <plat/devs.h> @@ -344,20 +343,13 @@ static struct i2c_board_info osiris_i2c_devs[] __initdata = { /* Standard Osiris devices */ static struct platform_device *osiris_devices[] __initdata = { + &s3c2410_device_dclk, &s3c_device_i2c0, &s3c_device_wdt, &s3c_device_nand, &osiris_pcmcia, }; -static struct clk *osiris_clocks[] __initdata = { - &s3c24xx_dclk0, - &s3c24xx_dclk1, - &s3c24xx_clkout0, - &s3c24xx_clkout1, - &s3c24xx_uclk, -}; - static struct s3c_cpufreq_board __initdata osiris_cpufreq = { .refresh = 7800, /* refresh period is 7.8usec */ .auto_io = 1, @@ -368,23 +360,7 @@ static void __init osiris_map_io(void) { unsigned long flags; - /* initialise the clocks */ - - s3c24xx_dclk0.parent = &clk_upll; - s3c24xx_dclk0.rate = 12*1000*1000; - - s3c24xx_dclk1.parent = &clk_upll; - s3c24xx_dclk1.rate = 24*1000*1000; - - s3c24xx_clkout0.parent = &s3c24xx_dclk0; - s3c24xx_clkout1.parent = &s3c24xx_dclk1; - - s3c24xx_uclk.parent = &s3c24xx_clkout1; - - s3c24xx_register_clocks(osiris_clocks, ARRAY_SIZE(osiris_clocks)); - s3c24xx_init_io(osiris_iodesc, ARRAY_SIZE(osiris_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(osiris_uartcfgs, ARRAY_SIZE(osiris_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); @@ -408,6 +384,12 @@ static void __init osiris_map_io(void) local_irq_restore(flags); } +static void __init osiris_init_time(void) +{ + s3c2440_init_clocks(12000000); + samsung_timer_init(); +} + static void __init osiris_init(void) { register_syscore_ops(&osiris_pm_syscore_ops); @@ -429,6 +411,6 @@ MACHINE_START(OSIRIS, "Simtec-OSIRIS") .map_io = osiris_map_io, .init_irq = s3c2440_init_irq, .init_machine = osiris_init, - .init_time = samsung_timer_init, + .init_time = osiris_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-otom.c b/arch/arm/mach-s3c24xx/mach-otom.c index bdb3faac2d9b..45833001186d 100644 --- a/arch/arm/mach-s3c24xx/mach-otom.c +++ b/arch/arm/mach-s3c24xx/mach-otom.c @@ -30,7 +30,6 @@ #include <mach/hardware.h> #include <mach/regs-gpio.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/devs.h> #include <plat/samsung-time.h> @@ -100,11 +99,16 @@ static struct platform_device *otom11_devices[] __initdata = { static void __init otom11_map_io(void) { s3c24xx_init_io(otom11_iodesc, ARRAY_SIZE(otom11_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(otom11_uartcfgs, ARRAY_SIZE(otom11_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init otom11_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + static void __init otom11_init(void) { s3c_i2c0_set_platdata(NULL); @@ -117,6 +121,6 @@ MACHINE_START(OTOM, "Nex Vision - Otom 1.1") .map_io = otom11_map_io, .init_machine = otom11_init, .init_irq = s3c2410_init_irq, - .init_time = samsung_timer_init, + .init_time = otom11_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-qt2410.c b/arch/arm/mach-s3c24xx/mach-qt2410.c index 8c12787a8fd3..228c9094519d 100644 --- a/arch/arm/mach-s3c24xx/mach-qt2410.c +++ b/arch/arm/mach-s3c24xx/mach-qt2410.c @@ -304,11 +304,16 @@ __setup("tft=", qt2410_tft_setup); static void __init qt2410_map_io(void) { s3c24xx_init_io(qt2410_iodesc, ARRAY_SIZE(qt2410_iodesc)); - s3c24xx_init_clocks(12*1000*1000); s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init qt2410_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + static void __init qt2410_machine_init(void) { s3c_nand_set_platdata(&qt2410_nand_info); @@ -346,6 +351,6 @@ MACHINE_START(QT2410, "QT2410") .map_io = qt2410_map_io, .init_irq = s3c2410_init_irq, .init_machine = qt2410_machine_init, - .init_time = samsung_timer_init, + .init_time = qt2410_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-rx1950.c b/arch/arm/mach-s3c24xx/mach-rx1950.c index afb784e934c8..e2c6541909c1 100644 --- a/arch/arm/mach-s3c24xx/mach-rx1950.c +++ b/arch/arm/mach-s3c24xx/mach-rx1950.c @@ -54,7 +54,6 @@ #include <mach/regs-lcd.h> #include <mach/gpio-samsung.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/devs.h> #include <plat/pm.h> @@ -710,6 +709,7 @@ static struct i2c_board_info rx1950_i2c_devices[] = { }; static struct platform_device *rx1950_devices[] __initdata = { + &s3c2410_device_dclk, &s3c_device_lcd, &s3c_device_wdt, &s3c_device_i2c0, @@ -728,20 +728,9 @@ static struct platform_device *rx1950_devices[] __initdata = { &rx1950_leds, }; -static struct clk *rx1950_clocks[] __initdata = { - &s3c24xx_clkout0, - &s3c24xx_clkout1, -}; - static void __init rx1950_map_io(void) { - s3c24xx_clkout0.parent = &clk_h; - s3c24xx_clkout1.parent = &clk_f; - - s3c24xx_register_clocks(rx1950_clocks, ARRAY_SIZE(rx1950_clocks)); - s3c24xx_init_io(rx1950_iodesc, ARRAY_SIZE(rx1950_iodesc)); - s3c24xx_init_clocks(16934000); s3c24xx_init_uarts(rx1950_uartcfgs, ARRAY_SIZE(rx1950_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); @@ -754,6 +743,12 @@ static void __init rx1950_map_io(void) s3c_pm_init(); } +static void __init rx1950_init_time(void) +{ + s3c2442_init_clocks(16934000); + samsung_timer_init(); +} + static void __init rx1950_init_machine(void) { int i; @@ -816,6 +811,6 @@ MACHINE_START(RX1950, "HP iPAQ RX1950") .reserve = rx1950_reserve, .init_irq = s3c2442_init_irq, .init_machine = rx1950_init_machine, - .init_time = samsung_timer_init, + .init_time = rx1950_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-rx3715.c b/arch/arm/mach-s3c24xx/mach-rx3715.c index e6535ce1bc5c..6e749ec3a2ea 100644 --- a/arch/arm/mach-s3c24xx/mach-rx3715.c +++ b/arch/arm/mach-s3c24xx/mach-rx3715.c @@ -46,7 +46,6 @@ #include <mach/regs-lcd.h> #include <mach/gpio-samsung.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/devs.h> #include <plat/pm.h> @@ -179,11 +178,16 @@ static struct platform_device *rx3715_devices[] __initdata = { static void __init rx3715_map_io(void) { s3c24xx_init_io(rx3715_iodesc, ARRAY_SIZE(rx3715_iodesc)); - s3c24xx_init_clocks(16934000); s3c24xx_init_uarts(rx3715_uartcfgs, ARRAY_SIZE(rx3715_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init rx3715_init_time(void) +{ + s3c2440_init_clocks(16934000); + samsung_timer_init(); +} + /* H1940 and RX3715 need to reserve this for suspend */ static void __init rx3715_reserve(void) { @@ -210,6 +214,6 @@ MACHINE_START(RX3715, "IPAQ-RX3715") .reserve = rx3715_reserve, .init_irq = s3c2440_init_irq, .init_machine = rx3715_init_machine, - .init_time = samsung_timer_init, + .init_time = rx3715_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c b/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c index 70f0900d4bca..e4dcb9aa2ca2 100644 --- a/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c +++ b/arch/arm/mach-s3c24xx/mach-s3c2416-dt.c @@ -18,7 +18,6 @@ #include <linux/clocksource.h> #include <linux/irqchip.h> #include <linux/of_platform.h> -#include <linux/serial_core.h> #include <linux/serial_s3c.h> #include <asm/mach/arch.h> @@ -29,48 +28,14 @@ #include "common.h" -/* - * The following lookup table is used to override device names when devices - * are registered from device tree. This is temporarily added to enable - * device tree support addition for the S3C2416 architecture. - * - * For drivers that require platform data to be provided from the machine - * file, a platform data pointer can also be supplied along with the - * devices names. Usually, the platform data elements that cannot be parsed - * from the device tree by the drivers (example: function pointers) are - * supplied. But it should be noted that this is a temporary mechanism and - * at some point, the drivers should be capable of parsing all the platform - * data from the device tree. - */ -static const struct of_dev_auxdata s3c2416_auxdata_lookup[] __initconst = { - OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART, - "s3c2440-uart.0", NULL), - OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0x4000, - "s3c2440-uart.1", NULL), - OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0x8000, - "s3c2440-uart.2", NULL), - OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0xC000, - "s3c2440-uart.3", NULL), - OF_DEV_AUXDATA("samsung,s3c6410-sdhci", S3C_PA_HSMMC0, - "s3c-sdhci.0", NULL), - OF_DEV_AUXDATA("samsung,s3c6410-sdhci", S3C_PA_HSMMC1, - "s3c-sdhci.1", NULL), - OF_DEV_AUXDATA("samsung,s3c2440-i2c", S3C_PA_IIC, - "s3c2440-i2c.0", NULL), - {}, -}; - static void __init s3c2416_dt_map_io(void) { s3c24xx_init_io(NULL, 0); - s3c24xx_init_clocks(12000000); } static void __init s3c2416_dt_machine_init(void) { - of_platform_populate(NULL, of_default_bus_match_table, - s3c2416_auxdata_lookup, NULL); - + of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); s3c_pm_init(); } @@ -86,6 +51,5 @@ DT_MACHINE_START(S3C2416_DT, "Samsung S3C2416 (Flattened Device Tree)") .map_io = s3c2416_dt_map_io, .init_irq = irqchip_init, .init_machine = s3c2416_dt_machine_init, - .init_time = clocksource_of_init, .restart = s3c2416_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-smdk2410.c b/arch/arm/mach-s3c24xx/mach-smdk2410.c index f32924ee0e9f..419fadd6e446 100644 --- a/arch/arm/mach-s3c24xx/mach-smdk2410.c +++ b/arch/arm/mach-s3c24xx/mach-smdk2410.c @@ -99,11 +99,16 @@ static struct platform_device *smdk2410_devices[] __initdata = { static void __init smdk2410_map_io(void) { s3c24xx_init_io(smdk2410_iodesc, ARRAY_SIZE(smdk2410_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(smdk2410_uartcfgs, ARRAY_SIZE(smdk2410_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init smdk2410_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + static void __init smdk2410_init(void) { s3c_i2c0_set_platdata(NULL); @@ -118,6 +123,6 @@ MACHINE_START(SMDK2410, "SMDK2410") /* @TODO: request a new identifier and switc .map_io = smdk2410_map_io, .init_irq = s3c2410_init_irq, .init_machine = smdk2410_init, - .init_time = samsung_timer_init, + .init_time = smdk2410_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-smdk2413.c b/arch/arm/mach-s3c24xx/mach-smdk2413.c index 233fe52d2015..a38f8a049e22 100644 --- a/arch/arm/mach-s3c24xx/mach-smdk2413.c +++ b/arch/arm/mach-s3c24xx/mach-smdk2413.c @@ -106,11 +106,16 @@ static void __init smdk2413_fixup(struct tag *tags, char **cmdline, static void __init smdk2413_map_io(void) { s3c24xx_init_io(smdk2413_iodesc, ARRAY_SIZE(smdk2413_iodesc)); - s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(smdk2413_uartcfgs, ARRAY_SIZE(smdk2413_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init smdk2413_init_time(void) +{ + s3c2412_init_clocks(12000000); + samsung_timer_init(); +} + static void __init smdk2413_machine_init(void) { /* Turn off suspend on both USB ports, and switch the * selectable USB port to USB device mode. */ @@ -159,6 +164,6 @@ MACHINE_START(SMDK2413, "SMDK2413") .init_irq = s3c2412_init_irq, .map_io = smdk2413_map_io, .init_machine = smdk2413_machine_init, - .init_time = samsung_timer_init, + .init_time = smdk2413_init_time, .restart = s3c2412_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-smdk2416.c b/arch/arm/mach-s3c24xx/mach-smdk2416.c index b3b54d8e1410..fa6f30d23601 100644 --- a/arch/arm/mach-s3c24xx/mach-smdk2416.c +++ b/arch/arm/mach-s3c24xx/mach-smdk2416.c @@ -219,10 +219,15 @@ static struct platform_device *smdk2416_devices[] __initdata = { &s3c2443_device_dma, }; +static void __init smdk2416_init_time(void) +{ + s3c2416_init_clocks(12000000); + samsung_timer_init(); +} + static void __init smdk2416_map_io(void) { s3c24xx_init_io(smdk2416_iodesc, ARRAY_SIZE(smdk2416_iodesc)); - s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(smdk2416_uartcfgs, ARRAY_SIZE(smdk2416_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } @@ -257,6 +262,6 @@ MACHINE_START(SMDK2416, "SMDK2416") .init_irq = s3c2416_init_irq, .map_io = smdk2416_map_io, .init_machine = smdk2416_machine_init, - .init_time = samsung_timer_init, + .init_time = smdk2416_init_time, .restart = s3c2416_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-smdk2440.c b/arch/arm/mach-s3c24xx/mach-smdk2440.c index d071dcfea548..5fb89c0ae17a 100644 --- a/arch/arm/mach-s3c24xx/mach-smdk2440.c +++ b/arch/arm/mach-s3c24xx/mach-smdk2440.c @@ -38,7 +38,6 @@ #include <mach/fb.h> #include <linux/platform_data/i2c-s3c2410.h> -#include <plat/clock.h> #include <plat/devs.h> #include <plat/cpu.h> #include <plat/samsung-time.h> @@ -159,11 +158,16 @@ static struct platform_device *smdk2440_devices[] __initdata = { static void __init smdk2440_map_io(void) { s3c24xx_init_io(smdk2440_iodesc, ARRAY_SIZE(smdk2440_iodesc)); - s3c24xx_init_clocks(16934400); s3c24xx_init_uarts(smdk2440_uartcfgs, ARRAY_SIZE(smdk2440_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init smdk2440_init_time(void) +{ + s3c2440_init_clocks(16934400); + samsung_timer_init(); +} + static void __init smdk2440_machine_init(void) { s3c24xx_fb_set_platdata(&smdk2440_fb_info); @@ -180,6 +184,6 @@ MACHINE_START(S3C2440, "SMDK2440") .init_irq = s3c2440_init_irq, .map_io = smdk2440_map_io, .init_machine = smdk2440_machine_init, - .init_time = samsung_timer_init, + .init_time = smdk2440_init_time, .restart = s3c244x_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-smdk2443.c b/arch/arm/mach-s3c24xx/mach-smdk2443.c index 06c4d77de3a5..ef5d5ea33182 100644 --- a/arch/arm/mach-s3c24xx/mach-smdk2443.c +++ b/arch/arm/mach-s3c24xx/mach-smdk2443.c @@ -121,11 +121,16 @@ static struct platform_device *smdk2443_devices[] __initdata = { static void __init smdk2443_map_io(void) { s3c24xx_init_io(smdk2443_iodesc, ARRAY_SIZE(smdk2443_iodesc)); - s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(smdk2443_uartcfgs, ARRAY_SIZE(smdk2443_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init smdk2443_init_time(void) +{ + s3c2443_init_clocks(12000000); + samsung_timer_init(); +} + static void __init smdk2443_machine_init(void) { s3c_i2c0_set_platdata(NULL); @@ -145,6 +150,6 @@ MACHINE_START(SMDK2443, "SMDK2443") .init_irq = s3c2443_init_irq, .map_io = smdk2443_map_io, .init_machine = smdk2443_machine_init, - .init_time = samsung_timer_init, + .init_time = smdk2443_init_time, .restart = s3c2443_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-tct_hammer.c b/arch/arm/mach-s3c24xx/mach-tct_hammer.c index 4108b2f0cede..c616ca2d409e 100644 --- a/arch/arm/mach-s3c24xx/mach-tct_hammer.c +++ b/arch/arm/mach-s3c24xx/mach-tct_hammer.c @@ -135,11 +135,16 @@ static struct platform_device *tct_hammer_devices[] __initdata = { static void __init tct_hammer_map_io(void) { s3c24xx_init_io(tct_hammer_iodesc, ARRAY_SIZE(tct_hammer_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(tct_hammer_uartcfgs, ARRAY_SIZE(tct_hammer_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init tct_hammer_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + static void __init tct_hammer_init(void) { s3c_i2c0_set_platdata(NULL); @@ -151,6 +156,6 @@ MACHINE_START(TCT_HAMMER, "TCT_HAMMER") .map_io = tct_hammer_map_io, .init_irq = s3c2410_init_irq, .init_machine = tct_hammer_init, - .init_time = samsung_timer_init, + .init_time = tct_hammer_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-vr1000.c b/arch/arm/mach-s3c24xx/mach-vr1000.c index 1cc5b1bd51cd..f88c584c3001 100644 --- a/arch/arm/mach-s3c24xx/mach-vr1000.c +++ b/arch/arm/mach-s3c24xx/mach-vr1000.c @@ -43,7 +43,6 @@ #include <mach/regs-gpio.h> #include <mach/gpio-samsung.h> -#include <plat/clock.h> #include <plat/cpu.h> #include <plat/devs.h> #include <plat/samsung-time.h> @@ -286,6 +285,7 @@ static struct i2c_board_info vr1000_i2c_devs[] __initdata = { /* devices for this board */ static struct platform_device *vr1000_devices[] __initdata = { + &s3c2410_device_dclk, &s3c_device_ohci, &s3c_device_lcd, &s3c_device_wdt, @@ -299,14 +299,6 @@ static struct platform_device *vr1000_devices[] __initdata = { &vr1000_led3, }; -static struct clk *vr1000_clocks[] __initdata = { - &s3c24xx_dclk0, - &s3c24xx_dclk1, - &s3c24xx_clkout0, - &s3c24xx_clkout1, - &s3c24xx_uclk, -}; - static void vr1000_power_off(void) { gpio_direction_output(S3C2410_GPB(9), 1); @@ -314,29 +306,19 @@ static void vr1000_power_off(void) static void __init vr1000_map_io(void) { - /* initialise clock sources */ - - s3c24xx_dclk0.parent = &clk_upll; - s3c24xx_dclk0.rate = 12*1000*1000; - - s3c24xx_dclk1.parent = NULL; - s3c24xx_dclk1.rate = 3692307; - - s3c24xx_clkout0.parent = &s3c24xx_dclk0; - s3c24xx_clkout1.parent = &s3c24xx_dclk1; - - s3c24xx_uclk.parent = &s3c24xx_clkout1; - - s3c24xx_register_clocks(vr1000_clocks, ARRAY_SIZE(vr1000_clocks)); - pm_power_off = vr1000_power_off; s3c24xx_init_io(vr1000_iodesc, ARRAY_SIZE(vr1000_iodesc)); - s3c24xx_init_clocks(0); s3c24xx_init_uarts(vr1000_uartcfgs, ARRAY_SIZE(vr1000_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init vr1000_init_time(void) +{ + s3c2410_init_clocks(12000000); + samsung_timer_init(); +} + static void __init vr1000_init(void) { s3c_i2c0_set_platdata(NULL); @@ -357,6 +339,6 @@ MACHINE_START(VR1000, "Thorcom-VR1000") .map_io = vr1000_map_io, .init_machine = vr1000_init, .init_irq = s3c2410_init_irq, - .init_time = samsung_timer_init, + .init_time = vr1000_init_time, .restart = s3c2410_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/mach-vstms.c b/arch/arm/mach-s3c24xx/mach-vstms.c index 40868c0e0a68..6b706c915387 100644 --- a/arch/arm/mach-s3c24xx/mach-vstms.c +++ b/arch/arm/mach-s3c24xx/mach-vstms.c @@ -142,11 +142,16 @@ static void __init vstms_fixup(struct tag *tags, char **cmdline, static void __init vstms_map_io(void) { s3c24xx_init_io(vstms_iodesc, ARRAY_SIZE(vstms_iodesc)); - s3c24xx_init_clocks(12000000); s3c24xx_init_uarts(vstms_uartcfgs, ARRAY_SIZE(vstms_uartcfgs)); samsung_set_timer_source(SAMSUNG_PWM3, SAMSUNG_PWM4); } +static void __init vstms_init_time(void) +{ + s3c2412_init_clocks(12000000); + samsung_timer_init(); +} + static void __init vstms_init(void) { s3c_i2c0_set_platdata(NULL); @@ -162,6 +167,6 @@ MACHINE_START(VSTMS, "VSTMS") .init_irq = s3c2412_init_irq, .init_machine = vstms_init, .map_io = vstms_map_io, - .init_time = samsung_timer_init, + .init_time = vstms_init_time, .restart = s3c2412_restart, MACHINE_END diff --git a/arch/arm/mach-s3c24xx/pm.c b/arch/arm/mach-s3c24xx/pm.c index 68ea5b7e5dc7..b19256ec8d40 100644 --- a/arch/arm/mach-s3c24xx/pm.c +++ b/arch/arm/mach-s3c24xx/pm.c @@ -51,9 +51,6 @@ #define PFX "s3c24xx-pm: " static struct sleep_save core_save[] = { - SAVE_ITEM(S3C2410_LOCKTIME), - SAVE_ITEM(S3C2410_CLKCON), - /* we restore the timings here, with the proviso that the board * brings the system up in an slower, or equal frequency setting * to the original system. @@ -69,18 +66,6 @@ static struct sleep_save core_save[] = { SAVE_ITEM(S3C2410_BANKCON3), SAVE_ITEM(S3C2410_BANKCON4), SAVE_ITEM(S3C2410_BANKCON5), - -#ifndef CONFIG_CPU_FREQ - SAVE_ITEM(S3C2410_CLKDIVN), - SAVE_ITEM(S3C2410_MPLLCON), - SAVE_ITEM(S3C2410_REFRESH), -#endif - SAVE_ITEM(S3C2410_UPLLCON), - SAVE_ITEM(S3C2410_CLKSLOW), -}; - -static struct sleep_save misc_save[] = { - SAVE_ITEM(S3C2410_DCLKCON), }; /* s3c_pm_check_resume_pin @@ -140,12 +125,10 @@ void s3c_pm_configure_extint(void) void s3c_pm_restore_core(void) { s3c_pm_do_restore_core(core_save, ARRAY_SIZE(core_save)); - s3c_pm_do_restore(misc_save, ARRAY_SIZE(misc_save)); } void s3c_pm_save_core(void) { - s3c_pm_do_save(misc_save, ARRAY_SIZE(misc_save)); s3c_pm_do_save(core_save, ARRAY_SIZE(core_save)); } diff --git a/arch/arm/mach-s3c24xx/s3c2410.c b/arch/arm/mach-s3c24xx/s3c2410.c index 04b58cb49888..7eab88829883 100644 --- a/arch/arm/mach-s3c24xx/s3c2410.c +++ b/arch/arm/mach-s3c24xx/s3c2410.c @@ -85,62 +85,6 @@ void __init s3c2410_map_io(void) void __init_or_cpufreq s3c2410_setup_clocks(void) { - struct clk *xtal_clk; - unsigned long tmp; - unsigned long xtal; - unsigned long fclk; - unsigned long hclk; - unsigned long pclk; - - xtal_clk = clk_get(NULL, "xtal"); - xtal = clk_get_rate(xtal_clk); - clk_put(xtal_clk); - - /* now we've got our machine bits initialised, work out what - * clocks we've got */ - - fclk = s3c24xx_get_pll(__raw_readl(S3C2410_MPLLCON), xtal); - - tmp = __raw_readl(S3C2410_CLKDIVN); - - /* work out clock scalings */ - - hclk = fclk / ((tmp & S3C2410_CLKDIVN_HDIVN) ? 2 : 1); - pclk = hclk / ((tmp & S3C2410_CLKDIVN_PDIVN) ? 2 : 1); - - /* print brieft summary of clocks, etc */ - - printk("S3C2410: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", - print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); - - /* initialise the clocks here, to allow other things like the - * console to use them - */ - - s3c24xx_setup_clocks(fclk, hclk, pclk); -} - -/* fake ARMCLK for use with cpufreq, etc. */ - -static struct clk s3c2410_armclk = { - .name = "armclk", - .parent = &clk_f, - .id = -1, -}; - -static struct clk_lookup s3c2410_clk_lookup[] = { - CLKDEV_INIT(NULL, "clk_uart_baud0", &clk_p), - CLKDEV_INIT(NULL, "clk_uart_baud1", &s3c24xx_uclk), -}; - -void __init s3c2410_init_clocks(int xtal) -{ - s3c24xx_register_baseclocks(xtal); - s3c2410_setup_clocks(); - s3c2410_baseclk_add(); - s3c24xx_register_clock(&s3c2410_armclk); - clkdev_add_table(s3c2410_clk_lookup, ARRAY_SIZE(s3c2410_clk_lookup)); - samsung_wdt_reset_init(S3C24XX_VA_WATCHDOG); } struct bus_type s3c2410_subsys = { diff --git a/arch/arm/mach-s3c24xx/s3c2412.c b/arch/arm/mach-s3c24xx/s3c2412.c index 657cbaca80ac..d49f52fbc842 100644 --- a/arch/arm/mach-s3c24xx/s3c2412.c +++ b/arch/arm/mach-s3c24xx/s3c2412.c @@ -173,49 +173,6 @@ void __init s3c2412_map_io(void) void __init_or_cpufreq s3c2412_setup_clocks(void) { - struct clk *xtal_clk; - unsigned long tmp; - unsigned long xtal; - unsigned long fclk; - unsigned long hclk; - unsigned long pclk; - - xtal_clk = clk_get(NULL, "xtal"); - xtal = clk_get_rate(xtal_clk); - clk_put(xtal_clk); - - /* now we've got our machine bits initialised, work out what - * clocks we've got */ - - fclk = s3c24xx_get_pll(__raw_readl(S3C2410_MPLLCON), xtal * 2); - - clk_mpll.rate = fclk; - - tmp = __raw_readl(S3C2410_CLKDIVN); - - /* work out clock scalings */ - - hclk = fclk / ((tmp & S3C2412_CLKDIVN_HDIVN_MASK) + 1); - hclk /= ((tmp & S3C2412_CLKDIVN_ARMDIVN) ? 2 : 1); - pclk = hclk / ((tmp & S3C2412_CLKDIVN_PDIVN) ? 2 : 1); - - /* print brieft summary of clocks, etc */ - - printk("S3C2412: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", - print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); - - s3c24xx_setup_clocks(fclk, hclk, pclk); -} - -void __init s3c2412_init_clocks(int xtal) -{ - /* initialise the clocks here, to allow other things like the - * console to use them - */ - - s3c24xx_register_baseclocks(xtal); - s3c2412_setup_clocks(); - s3c2412_baseclk_add(); } /* need to register the subsystem before we actually register the device, and diff --git a/arch/arm/mach-s3c24xx/s3c2442.c b/arch/arm/mach-s3c24xx/s3c2442.c index 2c8adc028538..fb9da2b603a2 100644 --- a/arch/arm/mach-s3c24xx/s3c2442.c +++ b/arch/arm/mach-s3c24xx/s3c2442.c @@ -53,117 +53,6 @@ #include "common.h" -/* S3C2442 extended clock support */ - -static unsigned long s3c2442_camif_upll_round(struct clk *clk, - unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - int div; - - if (rate > parent_rate) - return parent_rate; - - div = parent_rate / rate; - - if (div == 3) - return parent_rate / 3; - - /* note, we remove the +/- 1 calculations for the divisor */ - - div /= 2; - - if (div < 1) - div = 1; - else if (div > 16) - div = 16; - - return parent_rate / (div * 2); -} - -static int s3c2442_camif_upll_setrate(struct clk *clk, unsigned long rate) -{ - unsigned long parent_rate = clk_get_rate(clk->parent); - unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN); - - rate = s3c2442_camif_upll_round(clk, rate); - - camdivn &= ~S3C2442_CAMDIVN_CAMCLK_DIV3; - - if (rate == parent_rate) { - camdivn &= ~S3C2440_CAMDIVN_CAMCLK_SEL; - } else if ((parent_rate / rate) == 3) { - camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; - camdivn |= S3C2442_CAMDIVN_CAMCLK_DIV3; - } else { - camdivn &= ~S3C2440_CAMDIVN_CAMCLK_MASK; - camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL; - camdivn |= (((parent_rate / rate) / 2) - 1); - } - - __raw_writel(camdivn, S3C2440_CAMDIVN); - - return 0; -} - -/* Extra S3C2442 clocks */ - -static struct clk s3c2442_clk_cam = { - .name = "camif", - .id = -1, - .enable = s3c2410_clkcon_enable, - .ctrlbit = S3C2440_CLKCON_CAMERA, -}; - -static struct clk s3c2442_clk_cam_upll = { - .name = "camif-upll", - .id = -1, - .ops = &(struct clk_ops) { - .set_rate = s3c2442_camif_upll_setrate, - .round_rate = s3c2442_camif_upll_round, - }, -}; - -static int s3c2442_clk_add(struct device *dev, struct subsys_interface *sif) -{ - struct clk *clock_upll; - struct clk *clock_h; - struct clk *clock_p; - - clock_p = clk_get(NULL, "pclk"); - clock_h = clk_get(NULL, "hclk"); - clock_upll = clk_get(NULL, "upll"); - - if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) { - printk(KERN_ERR "S3C2442: Failed to get parent clocks\n"); - return -EINVAL; - } - - s3c2442_clk_cam.parent = clock_h; - s3c2442_clk_cam_upll.parent = clock_upll; - - s3c24xx_register_clock(&s3c2442_clk_cam); - s3c24xx_register_clock(&s3c2442_clk_cam_upll); - - clk_disable(&s3c2442_clk_cam); - - return 0; -} - -static struct subsys_interface s3c2442_clk_interface = { - .name = "s3c2442_clk", - .subsys = &s3c2442_subsys, - .add_dev = s3c2442_clk_add, -}; - -static __init int s3c2442_clk_init(void) -{ - return subsys_interface_register(&s3c2442_clk_interface); -} - -arch_initcall(s3c2442_clk_init); - - static struct device s3c2442_dev = { .bus = &s3c2442_subsys, }; diff --git a/arch/arm/mach-s3c24xx/s3c244x.c b/arch/arm/mach-s3c24xx/s3c244x.c index fe30ebb234d2..4a64bcc9eb51 100644 --- a/arch/arm/mach-s3c24xx/s3c244x.c +++ b/arch/arm/mach-s3c24xx/s3c244x.c @@ -46,6 +46,7 @@ #include <plat/nand-core.h> #include <plat/watchdog-reset.h> +#include "common.h" #include "regs-dsc.h" static struct map_desc s3c244x_iodesc[] __initdata = { @@ -74,67 +75,11 @@ void __init s3c244x_map_io(void) s3c_nand_setname("s3c2440-nand"); s3c_device_ts.name = "s3c2440-ts"; s3c_device_usbgadget.name = "s3c2440-usbgadget"; + s3c2410_device_dclk.name = "s3c2440-dclk"; } void __init_or_cpufreq s3c244x_setup_clocks(void) { - struct clk *xtal_clk; - unsigned long clkdiv; - unsigned long camdiv; - unsigned long xtal; - unsigned long hclk, fclk, pclk; - int hdiv = 1; - - xtal_clk = clk_get(NULL, "xtal"); - xtal = clk_get_rate(xtal_clk); - clk_put(xtal_clk); - - fclk = s3c24xx_get_pll(__raw_readl(S3C2410_MPLLCON), xtal) * 2; - - clkdiv = __raw_readl(S3C2410_CLKDIVN); - camdiv = __raw_readl(S3C2440_CAMDIVN); - - /* work out clock scalings */ - - switch (clkdiv & S3C2440_CLKDIVN_HDIVN_MASK) { - case S3C2440_CLKDIVN_HDIVN_1: - hdiv = 1; - break; - - case S3C2440_CLKDIVN_HDIVN_2: - hdiv = 2; - break; - - case S3C2440_CLKDIVN_HDIVN_4_8: - hdiv = (camdiv & S3C2440_CAMDIVN_HCLK4_HALF) ? 8 : 4; - break; - - case S3C2440_CLKDIVN_HDIVN_3_6: - hdiv = (camdiv & S3C2440_CAMDIVN_HCLK3_HALF) ? 6 : 3; - break; - } - - hclk = fclk / hdiv; - pclk = hclk / ((clkdiv & S3C2440_CLKDIVN_PDIVN) ? 2 : 1); - - /* print brief summary of clocks, etc */ - - printk("S3C244X: core %ld.%03ld MHz, memory %ld.%03ld MHz, peripheral %ld.%03ld MHz\n", - print_mhz(fclk), print_mhz(hclk), print_mhz(pclk)); - - s3c24xx_setup_clocks(fclk, hclk, pclk); -} - -void __init s3c244x_init_clocks(int xtal) -{ - /* initialise the clocks here, to allow other things like the - * console to use them, and to add new ones after the initialisation - */ - - s3c24xx_register_baseclocks(xtal); - s3c244x_setup_clocks(); - s3c2410_baseclk_add(); - samsung_wdt_reset_init(S3C24XX_VA_WATCHDOG); } /* Since the S3C2442 and S3C2440 share items, put both subsystems here */ diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h index 7231c8e4975e..72d4178ad23b 100644 --- a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h +++ b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h @@ -119,6 +119,7 @@ struct s3c_plltab { struct s3c_cpufreq_config { struct s3c_freq freq; struct s3c_freq max; + struct clk *mpll; struct cpufreq_frequency_table pll; struct s3c_clkdivs divs; struct s3c_cpufreq_info *info; /* for core, not drivers */ |