From 3a807b751c66e76bff39da4a9bd9828d7866d025 Mon Sep 17 00:00:00 2001 From: John Allen Date: Tue, 6 Jun 2017 16:55:52 -0500 Subject: ibmvnic: Return failure on attempted mtu change Changing the mtu is currently not supported in the ibmvnic driver. Implement .ndo_change_mtu in the driver so that attempting to use ifconfig to change the mtu will fail and present the user with an error message. Signed-off-by: John Allen Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/ibmvnic.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/net/ethernet/ibm') diff --git a/drivers/net/ethernet/ibm/ibmvnic.c b/drivers/net/ethernet/ibm/ibmvnic.c index a93757c255f7..c0fbeb387db4 100644 --- a/drivers/net/ethernet/ibm/ibmvnic.c +++ b/drivers/net/ethernet/ibm/ibmvnic.c @@ -1468,6 +1468,11 @@ static void ibmvnic_netpoll_controller(struct net_device *dev) } #endif +static int ibmvnic_change_mtu(struct net_device *netdev, int new_mtu) +{ + return -EOPNOTSUPP; +} + static const struct net_device_ops ibmvnic_netdev_ops = { .ndo_open = ibmvnic_open, .ndo_stop = ibmvnic_close, @@ -1479,6 +1484,7 @@ static const struct net_device_ops ibmvnic_netdev_ops = { #ifdef CONFIG_NET_POLL_CONTROLLER .ndo_poll_controller = ibmvnic_netpoll_controller, #endif + .ndo_change_mtu = ibmvnic_change_mtu, }; /* ethtool functions */ -- cgit v1.2.1 From 19d90ece81da802207a9b91ce95a29fbdc40626e Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Wed, 7 Jun 2017 15:51:15 +0200 Subject: net: emac: fix reset timeout with AR8035 phy This patch fixes a problem where the AR8035 PHY can't be detected on an Cisco Meraki MR24, if the ethernet cable is not connected on boot. Russell Senior provided steps to reproduce the issue: |Disconnect ethernet cable, apply power, wait until device has booted, |plug in ethernet, check for interfaces, no eth0 is listed. | |This appears to be a problem during probing of the AR8035 Phy chip. |When ethernet has no link, the phy detection fails, and eth0 is not |created. Plugging ethernet later has no effect, because there is no |interface as far as the kernel is concerned. The relevant part of |the boot log looks like this: |this is the failing case: | |[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode |[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout |[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY! |and the succeeding case: | |[ 0.876672] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode |[ 0.883952] eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 00:01:.. |[ 0.890822] eth0: found Atheros 8035 Gigabit Ethernet PHY (0x01) Based on the comment and the commit message of commit 23fbb5a87c56 ("emac: Fix EMAC soft reset on 460EX/GT"). This is because the AR8035 PHY doesn't provide the TX Clock, if the ethernet cable is not attached. This causes the reset to timeout and the PHY detection code in emac_init_phy() is unable to detect the AR8035 PHY. As a result, the emac driver bails out early and the user left with no ethernet. In order to stay compatible with existing configurations, the driver tries the current reset approach at first. Only if the first attempt timed out, it does perform one more retry with the clock temporarily switched to the internal source for just the duration of the reset. LEDE-Bug: #687 Cc: Chris Blake Reported-by: Russell Senior Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT") Signed-off-by: Christian Lamparter Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/emac/core.c | 26 ++++++++++++++++++++++---- 1 file changed, 22 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet/ibm') diff --git a/drivers/net/ethernet/ibm/emac/core.c b/drivers/net/ethernet/ibm/emac/core.c index 508923f39ccf..b6e871bfb659 100644 --- a/drivers/net/ethernet/ibm/emac/core.c +++ b/drivers/net/ethernet/ibm/emac/core.c @@ -343,6 +343,7 @@ static int emac_reset(struct emac_instance *dev) { struct emac_regs __iomem *p = dev->emacp; int n = 20; + bool __maybe_unused try_internal_clock = false; DBG(dev, "reset" NL); @@ -355,6 +356,7 @@ static int emac_reset(struct emac_instance *dev) } #ifdef CONFIG_PPC_DCR_NATIVE +do_retry: /* * PPC460EX/GT Embedded Processor Advanced User's Manual * section 28.10.1 Mode Register 0 (EMACx_MR0) states: @@ -362,10 +364,19 @@ static int emac_reset(struct emac_instance *dev) * of the EMAC. If none is present, select the internal clock * (SDR0_ETH_CFG[EMACx_PHY_CLK] = 1). * After a soft reset, select the external clock. + * + * The AR8035-A PHY Meraki MR24 does not provide a TX Clk if the + * ethernet cable is not attached. This causes the reset to timeout + * and the PHY detection code in emac_init_phy() is unable to + * communicate and detect the AR8035-A PHY. As a result, the emac + * driver bails out early and the user has no ethernet. + * In order to stay compatible with existing configurations, the + * driver will temporarily switch to the internal clock, after + * the first reset fails. */ if (emac_has_feature(dev, EMAC_FTR_460EX_PHY_CLK_FIX)) { - if (dev->phy_address == 0xffffffff && - dev->phy_map == 0xffffffff) { + if (try_internal_clock || (dev->phy_address == 0xffffffff && + dev->phy_map == 0xffffffff)) { /* No PHY: select internal loop clock before reset */ dcri_clrset(SDR0, SDR0_ETH_CFG, 0, SDR0_ETH_CFG_ECS << dev->cell_index); @@ -383,8 +394,15 @@ static int emac_reset(struct emac_instance *dev) #ifdef CONFIG_PPC_DCR_NATIVE if (emac_has_feature(dev, EMAC_FTR_460EX_PHY_CLK_FIX)) { - if (dev->phy_address == 0xffffffff && - dev->phy_map == 0xffffffff) { + if (!n && !try_internal_clock) { + /* first attempt has timed out. */ + n = 20; + try_internal_clock = true; + goto do_retry; + } + + if (try_internal_clock || (dev->phy_address == 0xffffffff && + dev->phy_map == 0xffffffff)) { /* No PHY: restore external clock source after reset */ dcri_clrset(SDR0, SDR0_ETH_CFG, SDR0_ETH_CFG_ECS << dev->cell_index, 0); -- cgit v1.2.1 From 9065bc386fcf52dee8f697450ddeb788e1bd514c Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Wed, 7 Jun 2017 15:51:16 +0200 Subject: net: emac: fix and unify emac_mdio functions emac_mdio_read_link() was not copying the requested phy settings back into the emac driver's own phy api. This has caused a link speed mismatch issue for the AR8035 as the emac driver kept trying to connect with 10/100MBps on a 1GBit/s link. This patch also unifies shared code between emac_setup_aneg() and emac_mdio_setup_forced(). And furthermore it removes a chunk of emac_mdio_init_phy(), that was copying the same data into itself. Signed-off-by: Christian Lamparter Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/emac/core.c | 41 ++++++++++++++++-------------------- 1 file changed, 18 insertions(+), 23 deletions(-) (limited to 'drivers/net/ethernet/ibm') diff --git a/drivers/net/ethernet/ibm/emac/core.c b/drivers/net/ethernet/ibm/emac/core.c index b6e871bfb659..259e69a52ec5 100644 --- a/drivers/net/ethernet/ibm/emac/core.c +++ b/drivers/net/ethernet/ibm/emac/core.c @@ -2478,20 +2478,24 @@ static int emac_mii_bus_reset(struct mii_bus *bus) return emac_reset(dev); } +static int emac_mdio_phy_start_aneg(struct mii_phy *phy, + struct phy_device *phy_dev) +{ + phy_dev->autoneg = phy->autoneg; + phy_dev->speed = phy->speed; + phy_dev->duplex = phy->duplex; + phy_dev->advertising = phy->advertising; + return phy_start_aneg(phy_dev); +} + static int emac_mdio_setup_aneg(struct mii_phy *phy, u32 advertise) { struct net_device *ndev = phy->dev; struct emac_instance *dev = netdev_priv(ndev); - dev->phy.autoneg = AUTONEG_ENABLE; - dev->phy.speed = SPEED_1000; - dev->phy.duplex = DUPLEX_FULL; - dev->phy.advertising = advertise; phy->autoneg = AUTONEG_ENABLE; - phy->speed = dev->phy.speed; - phy->duplex = dev->phy.duplex; phy->advertising = advertise; - return phy_start_aneg(dev->phy_dev); + return emac_mdio_phy_start_aneg(phy, dev->phy_dev); } static int emac_mdio_setup_forced(struct mii_phy *phy, int speed, int fd) @@ -2499,13 +2503,10 @@ static int emac_mdio_setup_forced(struct mii_phy *phy, int speed, int fd) struct net_device *ndev = phy->dev; struct emac_instance *dev = netdev_priv(ndev); - dev->phy.autoneg = AUTONEG_DISABLE; - dev->phy.speed = speed; - dev->phy.duplex = fd; phy->autoneg = AUTONEG_DISABLE; phy->speed = speed; phy->duplex = fd; - return phy_start_aneg(dev->phy_dev); + return emac_mdio_phy_start_aneg(phy, dev->phy_dev); } static int emac_mdio_poll_link(struct mii_phy *phy) @@ -2527,16 +2528,17 @@ static int emac_mdio_read_link(struct mii_phy *phy) { struct net_device *ndev = phy->dev; struct emac_instance *dev = netdev_priv(ndev); + struct phy_device *phy_dev = dev->phy_dev; int res; - res = phy_read_status(dev->phy_dev); + res = phy_read_status(phy_dev); if (res) return res; - dev->phy.speed = phy->speed; - dev->phy.duplex = phy->duplex; - dev->phy.pause = phy->pause; - dev->phy.asym_pause = phy->asym_pause; + phy->speed = phy_dev->speed; + phy->duplex = phy_dev->duplex; + phy->pause = phy_dev->pause; + phy->asym_pause = phy_dev->asym_pause; return 0; } @@ -2546,13 +2548,6 @@ static int emac_mdio_init_phy(struct mii_phy *phy) struct emac_instance *dev = netdev_priv(ndev); phy_start(dev->phy_dev); - dev->phy.autoneg = phy->autoneg; - dev->phy.speed = phy->speed; - dev->phy.duplex = phy->duplex; - dev->phy.advertising = phy->advertising; - dev->phy.pause = phy->pause; - dev->phy.asym_pause = phy->asym_pause; - return phy_init_hw(dev->phy_dev); } -- cgit v1.2.1