diff options
Diffstat (limited to 'Documentation/devicetree')
20 files changed, 694 insertions, 15 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards index 556c8665fdbf..b78564b2b201 100644 --- a/Documentation/devicetree/bindings/arm/arm-boards +++ b/Documentation/devicetree/bindings/arm/arm-boards @@ -23,7 +23,7 @@ Required nodes: range of 0x200 bytes. - syscon: the root node of the Integrator platforms must have a - system controller node pointong to the control registers, + system controller node pointing to the control registers, with the compatible string "arm,integrator-ap-syscon" "arm,integrator-cp-syscon" diff --git a/Documentation/devicetree/bindings/arm/fw-cfg.txt b/Documentation/devicetree/bindings/arm/fw-cfg.txt new file mode 100644 index 000000000000..953fb640d9c4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/fw-cfg.txt @@ -0,0 +1,72 @@ +* QEMU Firmware Configuration bindings for ARM + +QEMU's arm-softmmu and aarch64-softmmu emulation / virtualization targets +provide the following Firmware Configuration interface on the "virt" machine +type: + +- A write-only, 16-bit wide selector (or control) register, +- a read-write, 64-bit wide data register. + +QEMU exposes the control and data register to ARM guests as memory mapped +registers; their location is communicated to the guest's UEFI firmware in the +DTB that QEMU places at the bottom of the guest's DRAM. + +The guest writes a selector value (a key) to the selector register, and then +can read the corresponding data (produced by QEMU) via the data register. If +the selected entry is writable, the guest can rewrite it through the data +register. + +The selector register takes keys in big endian byte order. + +The data register allows accesses with 8, 16, 32 and 64-bit width (only at +offset 0 of the register). Accesses larger than a byte are interpreted as +arrays, bundled together only for better performance. The bytes constituting +such a word, in increasing address order, correspond to the bytes that would +have been transferred by byte-wide accesses in chronological order. + +The interface allows guest firmware to download various parameters and blobs +that affect how the firmware works and what tables it installs for the guest +OS. For example, boot order of devices, ACPI tables, SMBIOS tables, kernel and +initrd images for direct kernel booting, virtual machine UUID, SMP information, +virtual NUMA topology, and so on. + +The authoritative registry of the valid selector values and their meanings is +the QEMU source code; the structure of the data blobs corresponding to the +individual key values is also defined in the QEMU source code. + +The presence of the registers can be verified by selecting the "signature" blob +with key 0x0000, and reading four bytes from the data register. The returned +signature is "QEMU". + +The outermost protocol (involving the write / read sequences of the control and +data registers) is expected to be versioned, and/or described by feature bits. +The interface revision / feature bitmap can be retrieved with key 0x0001. The +blob to be read from the data register has size 4, and it is to be interpreted +as a uint32_t value in little endian byte order. The current value +(corresponding to the above outer protocol) is zero. + +The guest kernel is not expected to use these registers (although it is +certainly allowed to); the device tree bindings are documented here because +this is where device tree bindings reside in general. + +Required properties: + +- compatible: "qemu,fw-cfg-mmio". + +- reg: the MMIO region used by the device. + * Bytes 0x0 to 0x7 cover the data register. + * Bytes 0x8 to 0x9 cover the selector register. + * Further registers may be appended to the region in case of future interface + revisions / feature bits. + +Example: + +/ { + #size-cells = <0x2>; + #address-cells = <0x2>; + + fw-cfg@9020000 { + compatible = "qemu,fw-cfg-mmio"; + reg = <0x0 0x9020000 0x0 0xa>; + }; +}; diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index 4ab09f2202d4..c2340eeeb97f 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -37,9 +37,10 @@ Required properties when using sub-nodes: Sub-nodes required properties: -- reg : the port number -- phys : reference to the SATA PHY node - +- reg : the port number +And at least one of the following properties: +- phys : reference to the SATA PHY node +- target-supply : regulator for SATA target power Examples: sata@ffe08000 { @@ -68,10 +69,12 @@ With sub-nodes: sata0: sata-port@0 { reg = <0>; phys = <&sata_phy 0>; + target-supply = <®_sata0>; }; sata1: sata-port@1 { reg = <1>; phys = <&sata_phy 1>; + target-supply = <®_sata1>;; }; }; diff --git a/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt new file mode 100644 index 000000000000..b54bf3a2ff57 --- /dev/null +++ b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt @@ -0,0 +1,110 @@ + +* Samsung Exynos PPMU (Platform Performance Monitoring Unit) device + +The Samsung Exynos SoC has PPMU (Platform Performance Monitoring Unit) for +each IP. PPMU provides the primitive values to get performance data. These +PPMU events provide information of the SoC's behaviors so that you may +use to analyze system performance, to make behaviors visible and to count +usages of each IP (DMC, CPU, RIGHTBUS, LEFTBUS, CAM interface, LCD, G3D, MFC). +The Exynos PPMU driver uses the devfreq-event class to provide event data +to various devfreq devices. The devfreq devices would use the event data when +derterming the current state of each IP. + +Required properties: +- compatible: Should be "samsung,exynos-ppmu". +- reg: physical base address of each PPMU and length of memory mapped region. + +Optional properties: +- clock-names : the name of clock used by the PPMU, "ppmu" +- clocks : phandles for clock specified in "clock-names" property +- #clock-cells: should be 1. + +Example1 : PPMU nodes in exynos3250.dtsi are listed below. + + ppmu_dmc0: ppmu_dmc0@106a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106a0000 0x2000>; + status = "disabled"; + }; + + ppmu_dmc1: ppmu_dmc1@106b0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106b0000 0x2000>; + status = "disabled"; + }; + + ppmu_cpu: ppmu_cpu@106c0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x106c0000 0x2000>; + status = "disabled"; + }; + + ppmu_rightbus: ppmu_rightbus@112a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x112a0000 0x2000>; + clocks = <&cmu CLK_PPMURIGHT>; + clock-names = "ppmu"; + status = "disabled"; + }; + + ppmu_leftbus: ppmu_leftbus0@116a0000 { + compatible = "samsung,exynos-ppmu"; + reg = <0x116a0000 0x2000>; + clocks = <&cmu CLK_PPMULEFT>; + clock-names = "ppmu"; + status = "disabled"; + }; + +Example2 : Events of each PPMU node in exynos3250-rinato.dts are listed below. + + &ppmu_dmc0 { + status = "okay"; + + events { + ppmu_dmc0_3: ppmu-event3-dmc0 { + event-name = "ppmu-event3-dmc0"; + }; + + ppmu_dmc0_2: ppmu-event2-dmc0 { + event-name = "ppmu-event2-dmc0"; + }; + + ppmu_dmc0_1: ppmu-event1-dmc0 { + event-name = "ppmu-event1-dmc0"; + }; + + ppmu_dmc0_0: ppmu-event0-dmc0 { + event-name = "ppmu-event0-dmc0"; + }; + }; + }; + + &ppmu_dmc1 { + status = "okay"; + + events { + ppmu_dmc1_3: ppmu-event3-dmc1 { + event-name = "ppmu-event3-dmc1"; + }; + }; + }; + + &ppmu_leftbus { + status = "okay"; + + events { + ppmu_leftbus_3: ppmu-event3-leftbus { + event-name = "ppmu-event3-leftbus"; + }; + }; + }; + + &ppmu_rightbus { + status = "okay"; + + events { + ppmu_rightbus_3: ppmu-event3-rightbus { + event-name = "ppmu-event3-rightbus"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/graph.txt b/Documentation/devicetree/bindings/graph.txt index 1a69c078adf2..fcb1c6a4787b 100644 --- a/Documentation/devicetree/bindings/graph.txt +++ b/Documentation/devicetree/bindings/graph.txt @@ -19,7 +19,7 @@ type of the connections, they just map their existence. Specific properties may be described by specialized bindings depending on the type of connection. To see how this binding applies to video pipelines, for example, see -Documentation/device-tree/bindings/media/video-interfaces.txt. +Documentation/devicetree/bindings/media/video-interfaces.txt. Here the ports describe data interfaces, and the links between them are the connecting data buses. A single port with multiple connections can correspond to multiple devices being connected to the same physical bus. diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt index 437e0db3823c..4c26fda3844a 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-st.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -31,7 +31,7 @@ i2c0: i2c@fed40000 { compatible = "st,comms-ssc4-i2c"; reg = <0xfed40000 0x110>; interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&CLK_S_ICN_REG_0>; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; clock-names = "ssc"; clock-frequency = <400000>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 9f4e3824e71e..9f41d05be3be 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -47,6 +47,7 @@ dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O dallas,ds75 Digital Thermometer and Thermostat dlg,da9053 DA9053: flexible system level PMIC with multicore support +dlg,da9063 DA9063: system PMIC for quad-core application processors epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index a4a38fcf2ed6..44b705767aca 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -10,12 +10,13 @@ Optional properties: Each button (key) is represented as a sub-node of "gpio-keys": Subnode properties: + - gpios: OF device-tree gpio specification. + - interrupts: the interrupt line for that input. - label: Descriptive name of the key. - linux,code: Keycode to emit. -Required mutual exclusive subnode-properties: - - gpios: OF device-tree gpio specification. - - interrupts: the interrupt line for that input +Note that either "interrupts" or "gpios" properties can be omitted, but not +both at the same time. Specifying both properties is allowed. Optional subnode-properties: - linux,input-type: Specify event type this button/key generates. @@ -23,6 +24,9 @@ Optional subnode-properties: - debounce-interval: Debouncing interval time in milliseconds. If not specified defaults to 5. - gpio-key,wakeup: Boolean, button can wake-up the system. + - linux,can-disable: Boolean, indicates that button is connected + to dedicated (not shared) interrupt which can be disabled to + suppress events from the button. Example nodes: diff --git a/Documentation/devicetree/bindings/input/stmpe-keypad.txt b/Documentation/devicetree/bindings/input/stmpe-keypad.txt index 1b97222e8a0b..12bb771d66d4 100644 --- a/Documentation/devicetree/bindings/input/stmpe-keypad.txt +++ b/Documentation/devicetree/bindings/input/stmpe-keypad.txt @@ -8,6 +8,8 @@ Optional properties: - debounce-interval : Debouncing interval time in milliseconds - st,scan-count : Scanning cycles elapsed before key data is updated - st,no-autorepeat : If specified device will not autorepeat + - keypad,num-rows : See ./matrix-keymap.txt + - keypad,num-columns : See ./matrix-keymap.txt Example: diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index 75fdfaf41831..e39f0bc1f55e 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -39,6 +39,12 @@ to get matched with their hardware counterparts as follow: -BUCKn : 1-4. Use standard regulator bindings for it ('regulator-off-in-suspend'). + LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable + control. To turn this feature on this property must be added to the regulator + sub-node: + - maxim,ena-gpios : one GPIO specifier enable control (the gpio + flags are actually ignored and always + ACTIVE_HIGH is used) Example: @@ -65,4 +71,12 @@ Example: regulator-always-on; regulator-boot-on; }; + + buck9_reg { + regulator-compatible = "BUCK9"; + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; + }; } diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt index 032808843f90..24c5cdaba8d2 100644 --- a/Documentation/devicetree/bindings/net/davinci_emac.txt +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -4,7 +4,8 @@ This file provides information, what the device node for the davinci_emac interface contains. Required properties: -- compatible: "ti,davinci-dm6467-emac" or "ti,am3517-emac" +- compatible: "ti,davinci-dm6467-emac", "ti,am3517-emac" or + "ti,dm816-emac" - reg: Offset and length of the register set for the device - ti,davinci-ctrl-reg-offset: offset to control register - ti,davinci-ctrl-mod-reg-offset: offset to control module register diff --git a/Documentation/devicetree/bindings/pci/versatile.txt b/Documentation/devicetree/bindings/pci/versatile.txt new file mode 100644 index 000000000000..ebd1e7d0403e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/versatile.txt @@ -0,0 +1,59 @@ +* ARM Versatile Platform Baseboard PCI interface + +PCI host controller found on the ARM Versatile PB board's FPGA. + +Required properties: +- compatible: should contain "arm,versatile-pci" to identify the Versatile PCI + controller. +- reg: base addresses and lengths of the pci controller. There must be 3 + entries: + - Versatile-specific registers + - Self Config space + - Config space +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- bus-range: set to <0 0xff> +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties to define + the mapping of the PCI interface to interrupt numbers. + +Example: + +pci-controller@10001000 { + compatible = "arm,versatile-pci"; + device_type = "pci"; + reg = <0x10001000 0x1000 + 0x41000000 0x10000 + 0x42000000 0x100000>; + bus-range = <0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + ranges = <0x01000000 0 0x00000000 0x43000000 0 0x00010000 /* downstream I/O */ + 0x02000000 0 0x50000000 0x50000000 0 0x10000000 /* non-prefetchable memory */ + 0x42000000 0 0x60000000 0x60000000 0 0x10000000>; /* prefetchable memory */ + + interrupt-map-mask = <0x1800 0 0 7>; + interrupt-map = <0x1800 0 0 1 &sic 28 + 0x1800 0 0 2 &sic 29 + 0x1800 0 0 3 &sic 30 + 0x1800 0 0 4 &sic 27 + + 0x1000 0 0 1 &sic 27 + 0x1000 0 0 2 &sic 28 + 0x1000 0 0 3 &sic 29 + 0x1000 0 0 4 &sic 30 + + 0x0800 0 0 1 &sic 30 + 0x0800 0 0 2 &sic 27 + 0x0800 0 0 3 &sic 28 + 0x0800 0 0 4 &sic 29 + + 0x0000 0 0 1 &sic 29 + 0x0000 0 0 2 &sic 30 + 0x0000 0 0 3 &sic 27 + 0x0000 0 0 4 &sic 28>; +}; diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index 240019a82f9a..eb618907c7de 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -11,6 +11,7 @@ Required properties: BUCKA and BUCKB. Optional properties: +- enable-gpios: platform gpio for control of BUCKA/BUCKB. - Any optional property defined in regulator.txt Example 1) DA9211 @@ -27,6 +28,7 @@ Example 1) DA9211 regulator-max-microvolt = <1570000>; regulator-min-microamp = <2000000>; regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 27 0>; }; BUCKB { regulator-name = "VBUCKB"; @@ -34,11 +36,12 @@ Example 1) DA9211 regulator-max-microvolt = <1570000>; regulator-min-microamp = <2000000>; regulator-max-microamp = <5000000>; + enable-gpios = <&gpio 17 0>; }; }; }; -Example 2) DA92113 +Example 2) DA9213 pmic: da9213@68 { compatible = "dlg,da9213"; reg = <0x68>; @@ -51,6 +54,7 @@ Example 2) DA92113 regulator-max-microvolt = <1570000>; regulator-min-microamp = <3000000>; regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 27 0>; }; BUCKB { regulator-name = "VBUCKB"; @@ -58,6 +62,7 @@ Example 2) DA92113 regulator-max-microvolt = <1570000>; regulator-min-microamp = <3000000>; regulator-max-microamp = <6000000>; + enable-gpios = <&gpio 17 0>; }; }; }; diff --git a/Documentation/devicetree/bindings/regulator/isl9305.txt b/Documentation/devicetree/bindings/regulator/isl9305.txt index a626fc1bbf0d..d6e7c9ec9413 100644 --- a/Documentation/devicetree/bindings/regulator/isl9305.txt +++ b/Documentation/devicetree/bindings/regulator/isl9305.txt @@ -2,7 +2,7 @@ Intersil ISL9305/ISL9305H voltage regulator Required properties: -- compatible: "isl,isl9305" or "isl,isl9305h" +- compatible: "isil,isl9305" or "isil,isl9305h" - reg: I2C slave address, usually 0x68. - regulators: A node that houses a sub-node for each regulator within the device. Each sub-node is identified using the node's name, with valid @@ -19,7 +19,7 @@ Optional properties: Example pmic: isl9305@68 { - compatible = "isl,isl9305"; + compatible = "isil,isl9305"; reg = <0x68>; VINDCD1-supply = <&system_power>; diff --git a/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt new file mode 100644 index 000000000000..a42b1d6e9863 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6397-regulator.txt @@ -0,0 +1,217 @@ +Mediatek MT6397 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6397-regulator" +- mt6397regulator: List of regulators provided by this controller. It is named + according to its regulator type, buck_<name> and ldo_<name>. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are:: +BUCK: + buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu, + buck_vdrm, buck_vio18 +LDO: + ldo_vtcxo, ldo_va28, ldo_vcama, ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch, + ldo_vemc3v3, ldo_vgp1, ldo_vgp2, ldo_vgp3, ldo_vgp4, ldo_vgp5, ldo_vgp6, + ldo_vibr + +Example: + pmic { + compatible = "mediatek,mt6397"; + + mt6397regulator: mt6397regulator { + compatible = "mediatek,mt6397-regulator"; + + mt6397_vpca15_reg: buck_vpca15 { + regulator-compatible = "buck_vpca15"; + regulator-name = "vpca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <200>; + }; + + mt6397_vpca7_reg: buck_vpca7 { + regulator-compatible = "buck_vpca7"; + regulator-name = "vpca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vsramca15_reg: buck_vsramca15 { + regulator-compatible = "buck_vsramca15"; + regulator-name = "vsramca15"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vsramca7_reg: buck_vsramca7 { + regulator-compatible = "buck_vsramca7"; + regulator-name = "vsramca7"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + + }; + + mt6397_vcore_reg: buck_vcore { + regulator-compatible = "buck_vcore"; + regulator-name = "vcore"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vgpu_reg: buck_vgpu { + regulator-compatible = "buck_vgpu"; + regulator-name = "vgpu"; + regulator-min-microvolt = < 700000>; + regulator-max-microvolt = <1350000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <115>; + }; + + mt6397_vdrm_reg: buck_vdrm { + regulator-compatible = "buck_vdrm"; + regulator-name = "vdrm"; + regulator-min-microvolt = < 800000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vio18_reg: buck_vio18 { + regulator-compatible = "buck_vio18"; + regulator-name = "vio18"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2120000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <500>; + }; + + mt6397_vtcxo_reg: ldo_vtcxo { + regulator-compatible = "ldo_vtcxo"; + regulator-name = "vtcxo"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <90>; + }; + + mt6397_va28_reg: ldo_va28 { + regulator-compatible = "ldo_va28"; + regulator-name = "va28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vcama_reg: ldo_vcama { + regulator-compatible = "ldo_vcama"; + regulator-name = "vcama"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vio28_reg: ldo_vio28 { + regulator-compatible = "ldo_vio28"; + regulator-name = "vio28"; + /* fixed output 2.8 V */ + regulator-enable-ramp-delay = <240>; + }; + + mt6397_usb_reg: ldo_vusb { + regulator-compatible = "ldo_vusb"; + regulator-name = "vusb"; + /* fixed output 3.3 V */ + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmc_reg: ldo_vmc { + regulator-compatible = "ldo_vmc"; + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vmch_reg: ldo_vmch { + regulator-compatible = "ldo_vmch"; + regulator-name = "vmch"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vemc_3v3_reg: ldo_vemc3v3 { + regulator-compatible = "ldo_vemc3v3"; + regulator-name = "vemc_3v3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp1_reg: ldo_vgp1 { + regulator-compatible = "ldo_vgp1"; + regulator-name = "vcamd"; + regulator-min-microvolt = <1220000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <240>; + }; + + mt6397_vgp2_reg: ldo_vgp2 { + egulator-compatible = "ldo_vgp2"; + regulator-name = "vcamio"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp3_reg: ldo_vgp3 { + regulator-compatible = "ldo_vgp3"; + regulator-name = "vcamaf"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp4_reg: ldo_vgp4 { + regulator-compatible = "ldo_vgp4"; + regulator-name = "vgp4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp5_reg: ldo_vgp5 { + regulator-compatible = "ldo_vgp5"; + regulator-name = "vgp5"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vgp6_reg: ldo_vgp6 { + regulator-compatible = "ldo_vgp6"; + regulator-name = "vgp6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + + mt6397_vibr_reg: ldo_vibr { + regulator-compatible = "ldo_vibr"; + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt index 34ef5d16d0f1..9b40db88f637 100644 --- a/Documentation/devicetree/bindings/regulator/pfuze100.txt +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -1,7 +1,7 @@ PFUZE100 family of regulators Required properties: -- compatible: "fsl,pfuze100" or "fsl,pfuze200" +- compatible: "fsl,pfuze100", "fsl,pfuze200", "fsl,pfuze3000" - reg: I2C slave address Required child node: @@ -14,6 +14,8 @@ Required child node: sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6 --PFUZE200 sw1ab,sw2,sw3a,sw3b,swbst,vsnvs,vrefddr,vgen1~vgen6 + --PFUZE3000 + sw1a,sw1b,sw2,sw3,swbst,vsnvs,vrefddr,vldo1,vldo2,vccsd,v33,vldo3,vldo4 Each regulator is defined using the standard binding for regulators. @@ -205,3 +207,93 @@ Example 2: PFUZE200 }; }; }; + +Example 3: PFUZE3000 + + pmic: pfuze3000@08 { + compatible = "fsl,pfuze3000"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1a { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + /* use sw1c_reg to align with pfuze100/pfuze200 */ + sw1c_reg: sw1b { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1650000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen2_reg: vldo2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vccsd { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: v33 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + }; + + vgen5_reg: vldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index d11c3721e7cd..4c388bb2f0a2 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -30,6 +30,22 @@ Optional properties: specifiers, one for transmission, and one for reception. - dma-names : Must contain a list of two DMA names, "tx" and "rx". +- renesas,dtdl : delay sync signal (setup) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + +- renesas,syncdl : delay sync signal (hold) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + 300 (3-clock-cycle delay) Optional properties, deprecated for soctype-specific bindings: - renesas,tx-fifo-size : Overrides the default tx fifo size given in words diff --git a/Documentation/devicetree/bindings/spi/spi-sirf.txt b/Documentation/devicetree/bindings/spi/spi-sirf.txt new file mode 100644 index 000000000000..4c7adb8f777c --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sirf.txt @@ -0,0 +1,41 @@ +* CSR SiRFprimaII Serial Peripheral Interface + +Required properties: +- compatible : Should be "sirf,prima2-spi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI interrupt +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + +- #address-cells: Number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be zero. + +Optional properties: +- spi-max-frequency: Specifies maximum SPI clock frequency, + Units - Hz. Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +- cs-gpios: should specify GPIOs used for chipselects. + +Example: + +spi0: spi@b00d0000 { + compatible = "sirf,prima2-spi"; + reg = <0xb00d0000 0x10000>; + interrupts = <15>; + dmas = <&dmac1 9>, + <&dmac1 4>; + dma-names = "rx", "tx"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clks 19>; + resets = <&rstc 26>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-st-ssc.txt b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt new file mode 100644 index 000000000000..fe54959ec957 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt @@ -0,0 +1,40 @@ +STMicroelectronics SSC (SPI) Controller +--------------------------------------- + +Required properties: +- compatible : "st,comms-ssc4-spi" +- reg : Offset and length of the device's register set +- interrupts : The interrupt specifier +- clock-names : Must contain "ssc" +- clocks : Must contain an entry for each name in clock-names + See ../clk/* +- pinctrl-names : Uses "default", can use "sleep" if provided + See ../pinctrl/pinctrl-binding.txt + +Optional properties: +- cs-gpios : List of GPIO chip selects + See ../spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + spi@9840000 { + compatible = "st,comms-ssc4-spi"; + reg = <0x9840000 0x110>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; + clock-names = "ssc"; + pinctrl-0 = <&pinctrl_spi0_default>; + pinctrl-names = "default"; + cs-gpios = <&pio17 5 0>; + #address-cells = <1>; + #size-cells = <0>; + + st95hf@0{ + compatible = "st,st95hf"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + }; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index b1df0ad1306c..d443279c95dc 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -9,7 +9,6 @@ ad Avionic Design GmbH adapteva Adapteva, Inc. adi Analog Devices, Inc. aeroflexgaisler Aeroflex Gaisler AB -ak Asahi Kasei Corp. allwinner Allwinner Technology Co., Ltd. altr Altera Corp. amcc Applied Micro Circuits Corporation (APM, formally AMCC) @@ -20,6 +19,7 @@ amstaos AMS-Taos Inc. apm Applied Micro Circuits Corporation (APM) arm ARM Ltd. armadeus ARMadeus Systems SARL +asahi-kasei Asahi Kasei Corp. atmel Atmel Corporation auo AU Optronics Corporation avago Avago Technologies @@ -127,6 +127,7 @@ pixcir PIXCIR MICROELECTRONICS Co., Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc +qemu QEMU, a generic and open source machine emulator and virtualizer qnap QNAP Systems, Inc. radxa Radxa raidsonic RaidSonic Technology GmbH @@ -168,6 +169,7 @@ usi Universal Scientific Industrial Co., Ltd. v3 V3 Semiconductor variscite Variscite Ltd. via VIA Technologies, Inc. +virtio Virtual I/O Device Specification, developed by the OASIS consortium voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. wlf Wolfson Microelectronics |