diff options
Diffstat (limited to 'Documentation/hwmon/aquacomputer_d5next.rst')
-rw-r--r-- | Documentation/hwmon/aquacomputer_d5next.rst | 49 |
1 files changed, 23 insertions, 26 deletions
diff --git a/Documentation/hwmon/aquacomputer_d5next.rst b/Documentation/hwmon/aquacomputer_d5next.rst index 1f4bb4ba2e4b..3373e27b707d 100644 --- a/Documentation/hwmon/aquacomputer_d5next.rst +++ b/Documentation/hwmon/aquacomputer_d5next.rst @@ -6,22 +6,21 @@ Kernel driver aquacomputer-d5next Supported devices: * Aquacomputer D5 Next watercooling pump +* Aquacomputer Farbwerk 360 RGB controller Author: Aleksa Savic Description ----------- -This driver exposes hardware sensors of the Aquacomputer D5 Next watercooling -pump, which communicates through a proprietary USB HID protocol. +This driver exposes hardware sensors of listed Aquacomputer devices, which +communicate through proprietary USB HID protocols. -Available sensors are pump and fan speed, power, voltage and current, as -well as coolant temperature. Also available through debugfs are the serial -number, firmware version and power-on count. - -Attaching a fan is optional and allows it to be controlled using temperature -curves directly from the pump. If it's not connected, the fan-related sensors -will report zeroes. +For the D5 Next pump, available sensors are pump and fan speed, power, voltage +and current, as well as coolant temperature. Also available through debugfs are +the serial number, firmware version and power-on count. Attaching a fan to it is +optional and allows it to be controlled using temperature curves directly from the +pump. If it's not connected, the fan-related sensors will report zeroes. The pump can be configured either through software or via its physical interface. Configuring the pump through this driver is not implemented, as it @@ -29,33 +28,31 @@ seems to require sending it a complete configuration. That includes addressable RGB LEDs, for which there is no standard sysfs interface. Thus, that task is better suited for userspace tools. +The Farbwerk 360 exposes four temperature sensors. Depending on the device, +not all sysfs and debugfs entries will be available. + Usage notes ----------- -The pump communicates via HID reports. The driver is loaded automatically by +The devices communicate via HID reports. The driver is loaded automatically by the kernel and supports hotswapping. Sysfs entries ------------- -============ ============================================= -temp1_input Coolant temperature (in millidegrees Celsius) -fan1_input Pump speed (in RPM) -fan2_input Fan speed (in RPM) -power1_input Pump power (in micro Watts) -power2_input Fan power (in micro Watts) -in0_input Pump voltage (in milli Volts) -in1_input Fan voltage (in milli Volts) -in2_input +5V rail voltage (in milli Volts) -curr1_input Pump current (in milli Amperes) -curr2_input Fan current (in milli Amperes) -============ ============================================= +================ ============================================= +temp[1-4]_input Temperature sensors (in millidegrees Celsius) +fan[1-2]_input Pump/fan speed (in RPM) +power[1-2]_input Pump/fan power (in micro Watts) +in[0-2]_input Pump/fan voltage (in milli Volts) +curr[1-2]_input Pump/fan current (in milli Amperes) +================ ============================================= Debugfs entries --------------- -================ =============================================== -serial_number Serial number of the pump +================ ================================================= +serial_number Serial number of the device firmware_version Version of installed firmware -power_cycles Count of how many times the pump was powered on -================ =============================================== +power_cycles Count of how many times the device was powered on +================ ================================================= |