diff options
Diffstat (limited to 'arch/arm')
210 files changed, 2083 insertions, 1579 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 44789eff983f..e084b7e981e8 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1231,7 +1231,7 @@ config ARM_ERRATA_742231 capabilities of the processor. config PL310_ERRATA_588369 - bool "Clean & Invalidate maintenance operations do not invalidate clean lines" + bool "PL310 errata: Clean & Invalidate maintenance operations do not invalidate clean lines" depends on CACHE_L2X0 help The PL310 L2 cache controller implements three types of Clean & @@ -1256,7 +1256,7 @@ config ARM_ERRATA_720789 entries regardless of the ASID. config PL310_ERRATA_727915 - bool "Background Clean & Invalidate by Way operation can cause data corruption" + bool "PL310 errata: Background Clean & Invalidate by Way operation can cause data corruption" depends on CACHE_L2X0 help PL310 implements the Clean & Invalidate by Way L2 cache maintenance @@ -1289,8 +1289,8 @@ config ARM_ERRATA_751472 operation is received by a CPU before the ICIALLUIS has completed, potentially leading to corrupted entries in the cache or TLB. -config ARM_ERRATA_753970 - bool "ARM errata: cache sync operation may be faulty" +config PL310_ERRATA_753970 + bool "PL310 errata: cache sync operation may be faulty" depends on CACHE_PL310 help This option enables the workaround for the 753970 PL310 (r3p0) erratum. @@ -1352,6 +1352,18 @@ config ARM_ERRATA_764369 relevant cache maintenance functions and sets a specific bit in the diagnostic control register of the SCU. +config PL310_ERRATA_769419 + bool "PL310 errata: no automatic Store Buffer drain" + depends on CACHE_L2X0 + help + On revisions of the PL310 prior to r3p2, the Store Buffer does + not automatically drain. This can cause normal, non-cacheable + writes to be retained when the memory system is idle, leading + to suboptimal I/O performance for drivers using coherent DMA. + This option adds a write barrier to the cpu_idle loop so that, + on systems with an outer cache, the store buffer is drained + explicitly. + endmenu source "arch/arm/common/Kconfig" diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index c5213e78606b..e0d236d7ff73 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -100,6 +100,14 @@ choice Note that the system will appear to hang during boot if there is nothing connected to read from the DCC. + config AT91_DEBUG_LL_DBGU0 + bool "Kernel low-level debugging on rm9200, 9260/9g20, 9261/9g10 and 9rl" + depends on HAVE_AT91_DBGU0 + + config AT91_DEBUG_LL_DBGU1 + bool "Kernel low-level debugging on 9263, 9g45 and cap9" + depends on HAVE_AT91_DBGU1 + config DEBUG_FOOTBRIDGE_COM1 bool "Kernel low-level debugging messages via footbridge 8250 at PCI COM1" depends on FOOTBRIDGE @@ -247,6 +255,43 @@ choice their output to the standard serial port on the RealView PB1176 platform. + config DEBUG_MSM_UART1 + bool "Kernel low-level debugging messages via MSM UART1" + depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50 + help + Say Y here if you want the debug print routines to direct + their output to the first serial port on MSM devices. + + config DEBUG_MSM_UART2 + bool "Kernel low-level debugging messages via MSM UART2" + depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50 + help + Say Y here if you want the debug print routines to direct + their output to the second serial port on MSM devices. + + config DEBUG_MSM_UART3 + bool "Kernel low-level debugging messages via MSM UART3" + depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50 + help + Say Y here if you want the debug print routines to direct + their output to the third serial port on MSM devices. + + config DEBUG_MSM8660_UART + bool "Kernel low-level debugging messages via MSM 8660 UART" + depends on ARCH_MSM8X60 + select MSM_HAS_DEBUG_UART_HS + help + Say Y here if you want the debug print routines to direct + their output to the serial port on MSM 8660 devices. + + config DEBUG_MSM8960_UART + bool "Kernel low-level debugging messages via MSM 8960 UART" + depends on ARCH_MSM8960 + select MSM_HAS_DEBUG_UART_HS + help + Say Y here if you want the debug print routines to direct + their output to the serial port on MSM 8960 devices. + endchoice config EARLY_PRINTK diff --git a/arch/arm/common/gic.c b/arch/arm/common/gic.c index 0e6ae470c94f..410a546060a2 100644 --- a/arch/arm/common/gic.c +++ b/arch/arm/common/gic.c @@ -526,7 +526,8 @@ static void __init gic_pm_init(struct gic_chip_data *gic) sizeof(u32)); BUG_ON(!gic->saved_ppi_conf); - cpu_pm_register_notifier(&gic_notifier_block); + if (gic == &gic_data[0]) + cpu_pm_register_notifier(&gic_notifier_block); } #else static void __init gic_pm_init(struct gic_chip_data *gic) @@ -581,13 +582,16 @@ void __init gic_init(unsigned int gic_nr, int irq_start, * For primary GICs, skip over SGIs. * For secondary GICs, skip over PPIs, too. */ + domain->hwirq_base = 32; if (gic_nr == 0) { gic_cpu_base_addr = cpu_base; - domain->hwirq_base = 16; - if (irq_start > 0) - irq_start = (irq_start & ~31) + 16; - } else - domain->hwirq_base = 32; + + if ((irq_start & 31) > 0) { + domain->hwirq_base = 16; + if (irq_start != -1) + irq_start = (irq_start & ~31) + 16; + } + } /* * Find out how many interrupts are supported. diff --git a/arch/arm/common/pl330.c b/arch/arm/common/pl330.c index 7129cfbdacd6..f407a6b35d3d 100644 --- a/arch/arm/common/pl330.c +++ b/arch/arm/common/pl330.c @@ -1211,8 +1211,8 @@ static inline u32 _prepare_ccr(const struct pl330_reqcfg *rqc) ccr |= (rqc->brst_size << CC_SRCBRSTSIZE_SHFT); ccr |= (rqc->brst_size << CC_DSTBRSTSIZE_SHFT); - ccr |= (rqc->dcctl << CC_SRCCCTRL_SHFT); - ccr |= (rqc->scctl << CC_DSTCCTRL_SHFT); + ccr |= (rqc->scctl << CC_SRCCCTRL_SHFT); + ccr |= (rqc->dcctl << CC_DSTCCTRL_SHFT); ccr |= (rqc->swap << CC_SWAP_SHFT); @@ -1623,6 +1623,11 @@ static inline int _alloc_event(struct pl330_thread *thrd) return -1; } +static bool _chan_ns(const struct pl330_info *pi, int i) +{ + return pi->pcfg.irq_ns & (1 << i); +} + /* Upon success, returns IdentityToken for the * allocated channel, NULL otherwise. */ @@ -1647,7 +1652,8 @@ void *pl330_request_channel(const struct pl330_info *pi) for (i = 0; i < chans; i++) { thrd = &pl330->channels[i]; - if (thrd->free) { + if ((thrd->free) && (!_manager_ns(thrd) || + _chan_ns(pi, i))) { thrd->ev = _alloc_event(thrd); if (thrd->ev >= 0) { thrd->free = false; diff --git a/arch/arm/configs/at91cap9adk_defconfig b/arch/arm/configs/at91cap9_defconfig index ffb1edd93363..8826eb218e73 100644 --- a/arch/arm/configs/at91cap9adk_defconfig +++ b/arch/arm/configs/at91cap9_defconfig @@ -38,7 +38,6 @@ CONFIG_IP_PNP_RARP=y # CONFIG_IPV6 is not set CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_MTD=y -CONFIG_MTD_PARTITIONS=y CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_CHAR=y CONFIG_MTD_BLOCK=y @@ -52,16 +51,12 @@ CONFIG_MTD_NAND_ATMEL=y CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_SIZE=8192 -CONFIG_ATMEL_SSC=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_SCSI_MULTI_LUN=y CONFIG_NETDEVICES=y -CONFIG_NET_ETHERNET=y CONFIG_MII=y CONFIG_MACB=y -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_EVDEV=y # CONFIG_INPUT_KEYBOARD is not set @@ -81,7 +76,6 @@ CONFIG_WATCHDOG=y CONFIG_WATCHDOG_NOWAYOUT=y CONFIG_FB=y CONFIG_FB_ATMEL=y -# CONFIG_VGA_CONSOLE is not set CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_CLUT224 is not set @@ -99,7 +93,6 @@ CONFIG_MMC_AT91=m CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_AT91SAM9=y CONFIG_EXT2_FS=y -CONFIG_INOTIFY=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_JFFS2_FS=y diff --git a/arch/arm/configs/at91rm9200_defconfig b/arch/arm/configs/at91rm9200_defconfig index 38cb7c985426..bbe4e1a1f5d8 100644 --- a/arch/arm/configs/at91rm9200_defconfig +++ b/arch/arm/configs/at91rm9200_defconfig @@ -5,7 +5,6 @@ CONFIG_SYSVIPC=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 -CONFIG_SYSFS_DEPRECATED_V2=y CONFIG_BLK_DEV_INITRD=y CONFIG_MODULES=y CONFIG_MODULE_FORCE_LOAD=y @@ -56,7 +55,6 @@ CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y CONFIG_NET_IPIP=m -CONFIG_NET_IPGRE=m CONFIG_INET_AH=m CONFIG_INET_ESP=m CONFIG_INET_IPCOMP=m @@ -75,18 +73,8 @@ CONFIG_IPV6_TUNNEL=m CONFIG_BRIDGE=m CONFIG_VLAN_8021Q=m CONFIG_BT=m -CONFIG_BT_L2CAP=m -CONFIG_BT_SCO=m -CONFIG_BT_RFCOMM=m -CONFIG_BT_RFCOMM_TTY=y -CONFIG_BT_BNEP=m -CONFIG_BT_BNEP_MC_FILTER=y -CONFIG_BT_BNEP_PROTO_FILTER=y -CONFIG_BT_HIDP=m CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_MTD=y -CONFIG_MTD_CONCAT=y -CONFIG_MTD_PARTITIONS=y CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_AFS_PARTS=y CONFIG_MTD_CHAR=y @@ -108,8 +96,6 @@ CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_NBD=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_SIZE=8192 -CONFIG_ATMEL_TCLIB=y -CONFIG_EEPROM_LEGACY=m CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_BLK_DEV_SR=m @@ -119,14 +105,23 @@ CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_LOWLEVEL is not set CONFIG_NETDEVICES=y CONFIG_TUN=m +CONFIG_ARM_AT91_ETHER=y CONFIG_PHYLIB=y CONFIG_DAVICOM_PHY=y CONFIG_SMSC_PHY=y CONFIG_MICREL_PHY=y -CONFIG_NET_ETHERNET=y -CONFIG_ARM_AT91_ETHER=y -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set +CONFIG_PPP=y +CONFIG_PPP_BSDCOMP=y +CONFIG_PPP_DEFLATE=y +CONFIG_PPP_FILTER=y +CONFIG_PPP_MPPE=m +CONFIG_PPP_MULTILINK=y +CONFIG_PPPOE=m +CONFIG_PPP_ASYNC=y +CONFIG_SLIP=m +CONFIG_SLIP_COMPRESSED=y +CONFIG_SLIP_SMART=y +CONFIG_SLIP_MODE_SLIP6=y CONFIG_USB_CATC=m CONFIG_USB_KAWETH=m CONFIG_USB_PEGASUS=m @@ -139,18 +134,6 @@ CONFIG_USB_NET_RNDIS_HOST=m CONFIG_USB_ALI_M5632=y CONFIG_USB_AN2720=y CONFIG_USB_EPSON2888=y -CONFIG_PPP=y -CONFIG_PPP_MULTILINK=y -CONFIG_PPP_FILTER=y -CONFIG_PPP_ASYNC=y -CONFIG_PPP_DEFLATE=y -CONFIG_PPP_BSDCOMP=y -CONFIG_PPP_MPPE=m -CONFIG_PPPOE=m -CONFIG_SLIP=m -CONFIG_SLIP_COMPRESSED=y -CONFIG_SLIP_SMART=y -CONFIG_SLIP_MODE_SLIP6=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=640 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=480 @@ -158,9 +141,9 @@ CONFIG_INPUT_EVDEV=y CONFIG_KEYBOARD_GPIO=y # CONFIG_INPUT_MOUSE is not set CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_LEGACY_PTY_COUNT=32 CONFIG_SERIAL_ATMEL=y CONFIG_SERIAL_ATMEL_CONSOLE=y -CONFIG_LEGACY_PTY_COUNT=32 CONFIG_HW_RANDOM=y CONFIG_I2C=y CONFIG_I2C_CHARDEV=y @@ -290,7 +273,6 @@ CONFIG_NFS_V3_ACL=y CONFIG_NFS_V4=y CONFIG_ROOT_NFS=y CONFIG_NFSD=y -CONFIG_SMB_FS=m CONFIG_CIFS=m CONFIG_PARTITION_ADVANCED=y CONFIG_MAC_PARTITION=y @@ -335,7 +317,6 @@ CONFIG_NLS_UTF8=y CONFIG_MAGIC_SYSRQ=y CONFIG_DEBUG_FS=y CONFIG_DEBUG_KERNEL=y -# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_FTRACE is not set CONFIG_CRYPTO_PCBC=y CONFIG_CRYPTO_SHA1=y diff --git a/arch/arm/configs/at91sam9260ek_defconfig b/arch/arm/configs/at91sam9260_defconfig index f8a9226413bf..505b3765f87e 100644 --- a/arch/arm/configs/at91sam9260ek_defconfig +++ b/arch/arm/configs/at91sam9260_defconfig @@ -12,11 +12,23 @@ CONFIG_MODULE_UNLOAD=y # CONFIG_IOSCHED_CFQ is not set CONFIG_ARCH_AT91=y CONFIG_ARCH_AT91SAM9260=y +CONFIG_ARCH_AT91SAM9260_SAM9XE=y CONFIG_MACH_AT91SAM9260EK=y +CONFIG_MACH_CAM60=y +CONFIG_MACH_SAM9_L9260=y +CONFIG_MACH_AFEB9260=y +CONFIG_MACH_USB_A9260=y +CONFIG_MACH_QIL_A9260=y +CONFIG_MACH_CPU9260=y +CONFIG_MACH_FLEXIBITY=y +CONFIG_MACH_SNAPPER_9260=y +CONFIG_MACH_AT91SAM_DT=y CONFIG_AT91_PROGRAMMABLE_CLOCKS=y # CONFIG_ARM_THUMB is not set CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ARM_APPENDED_DTB=y +CONFIG_ARM_ATAG_DTB_COMPAT=y CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw" CONFIG_FPE_NWFPE=y CONFIG_NET=y @@ -33,12 +45,10 @@ CONFIG_IP_PNP_BOOTP=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_SIZE=8192 -CONFIG_ATMEL_SSC=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_SCSI_MULTI_LUN=y CONFIG_NETDEVICES=y -CONFIG_NET_ETHERNET=y CONFIG_MII=y CONFIG_MACB=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set @@ -55,7 +65,6 @@ CONFIG_I2C_GPIO=y CONFIG_WATCHDOG=y CONFIG_WATCHDOG_NOWAYOUT=y CONFIG_AT91SAM9X_WATCHDOG=y -# CONFIG_VGA_CONSOLE is not set # CONFIG_USB_HID is not set CONFIG_USB=y CONFIG_USB_DEVICEFS=y @@ -71,7 +80,6 @@ CONFIG_USB_G_SERIAL=m CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_AT91SAM9=y CONFIG_EXT2_FS=y -CONFIG_INOTIFY=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y CONFIG_CRAMFS=y diff --git a/arch/arm/configs/at91sam9g20ek_defconfig b/arch/arm/configs/at91sam9g20_defconfig index 9e90e6d79297..9123568d9a8d 100644 --- a/arch/arm/configs/at91sam9g20ek_defconfig +++ b/arch/arm/configs/at91sam9g20_defconfig @@ -14,6 +14,15 @@ CONFIG_ARCH_AT91=y CONFIG_ARCH_AT91SAM9G20=y CONFIG_MACH_AT91SAM9G20EK=y CONFIG_MACH_AT91SAM9G20EK_2MMC=y +CONFIG_MACH_CPU9G20=y +CONFIG_MACH_ACMENETUSFOXG20=y +CONFIG_MACH_PORTUXG20=y +CONFIG_MACH_STAMP9G20=y +CONFIG_MACH_PCONTROL_G20=y +CONFIG_MACH_GSIA18S=y +CONFIG_MACH_USB_A9G20=y +CONFIG_MACH_SNAPPER_9260=y +CONFIG_MACH_AT91SAM_DT=y CONFIG_AT91_PROGRAMMABLE_CLOCKS=y # CONFIG_ARM_THUMB is not set CONFIG_AEABI=y @@ -21,9 +30,10 @@ CONFIG_LEDS=y CONFIG_LEDS_CPU=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ARM_APPENDED_DTB=y +CONFIG_ARM_ATAG_DTB_COMPAT=y CONFIG_CMDLINE="mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw" CONFIG_FPE_NWFPE=y -CONFIG_PM=y CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y @@ -37,8 +47,6 @@ CONFIG_IP_PNP_BOOTP=y # CONFIG_IPV6 is not set CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_MTD=y -CONFIG_MTD_CONCAT=y -CONFIG_MTD_PARTITIONS=y CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_CHAR=y CONFIG_MTD_BLOCK=y @@ -48,17 +56,13 @@ CONFIG_MTD_NAND_ATMEL=y CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_SIZE=8192 -CONFIG_ATMEL_SSC=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_LOWLEVEL is not set CONFIG_NETDEVICES=y -CONFIG_NET_ETHERNET=y CONFIG_MII=y CONFIG_MACB=y -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_MOUSEDEV_SCREEN_X=320 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=240 @@ -66,15 +70,14 @@ CONFIG_INPUT_EVDEV=y # CONFIG_KEYBOARD_ATKBD is not set CONFIG_KEYBOARD_GPIO=y # CONFIG_INPUT_MOUSE is not set +CONFIG_LEGACY_PTY_COUNT=16 CONFIG_SERIAL_ATMEL=y CONFIG_SERIAL_ATMEL_CONSOLE=y -CONFIG_LEGACY_PTY_COUNT=16 CONFIG_HW_RANDOM=y CONFIG_SPI=y CONFIG_SPI_ATMEL=y CONFIG_SPI_SPIDEV=y # CONFIG_HWMON is not set -# CONFIG_VGA_CONSOLE is not set CONFIG_SOUND=y CONFIG_SND=y CONFIG_SND_SEQUENCER=y @@ -82,7 +85,6 @@ CONFIG_SND_MIXER_OSS=y CONFIG_SND_PCM_OSS=y CONFIG_SND_SEQUENCER_OSS=y # CONFIG_SND_VERBOSE_PROCFS is not set -CONFIG_SND_AT73C213=y CONFIG_USB=y CONFIG_USB_DEVICEFS=y # CONFIG_USB_DEVICE_CLASS is not set @@ -105,7 +107,6 @@ CONFIG_LEDS_TRIGGER_HEARTBEAT=y CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_AT91SAM9=y CONFIG_EXT2_FS=y -CONFIG_INOTIFY=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y diff --git a/arch/arm/configs/at91sam9g45_defconfig b/arch/arm/configs/at91sam9g45_defconfig index c5876d244f4b..606d48f3b8f8 100644 --- a/arch/arm/configs/at91sam9g45_defconfig +++ b/arch/arm/configs/at91sam9g45_defconfig @@ -18,6 +18,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_AT91=y CONFIG_ARCH_AT91SAM9G45=y CONFIG_MACH_AT91SAM9M10G45EK=y +CONFIG_MACH_AT91SAM_DT=y CONFIG_AT91_PROGRAMMABLE_CLOCKS=y CONFIG_AT91_SLOW_CLOCK=y CONFIG_AEABI=y @@ -73,11 +74,8 @@ CONFIG_SCSI_MULTI_LUN=y # CONFIG_SCSI_LOWLEVEL is not set CONFIG_NETDEVICES=y CONFIG_MII=y -CONFIG_DAVICOM_PHY=y -CONFIG_NET_ETHERNET=y CONFIG_MACB=y -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set +CONFIG_DAVICOM_PHY=y CONFIG_LIBERTAS_THINFIRM=m CONFIG_LIBERTAS_THINFIRM_USB=m CONFIG_AT76C50X_USB=m @@ -131,7 +129,6 @@ CONFIG_I2C_GPIO=y CONFIG_SPI=y CONFIG_SPI_ATMEL=y # CONFIG_HWMON is not set -# CONFIG_MFD_SUPPORT is not set CONFIG_FB=y CONFIG_FB_ATMEL=y CONFIG_FB_UDL=m diff --git a/arch/arm/configs/at91sam9rlek_defconfig b/arch/arm/configs/at91sam9rl_defconfig index 75621e4d03fc..ad562ee64209 100644 --- a/arch/arm/configs/at91sam9rlek_defconfig +++ b/arch/arm/configs/at91sam9rl_defconfig @@ -23,8 +23,6 @@ CONFIG_NET=y CONFIG_UNIX=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_MTD=y -CONFIG_MTD_CONCAT=y -CONFIG_MTD_PARTITIONS=y CONFIG_MTD_CMDLINE_PARTS=y CONFIG_MTD_CHAR=y CONFIG_MTD_BLOCK=y @@ -35,7 +33,6 @@ CONFIG_BLK_DEV_LOOP=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=4 CONFIG_BLK_DEV_RAM_SIZE=24576 -CONFIG_ATMEL_SSC=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_SCSI_MULTI_LUN=y @@ -62,13 +59,11 @@ CONFIG_WATCHDOG_NOWAYOUT=y CONFIG_AT91SAM9X_WATCHDOG=y CONFIG_FB=y CONFIG_FB_ATMEL=y -# CONFIG_VGA_CONSOLE is not set CONFIG_MMC=y CONFIG_MMC_AT91=m CONFIG_RTC_CLASS=y CONFIG_RTC_DRV_AT91SAM9=y CONFIG_EXT2_FS=y -CONFIG_INOTIFY=y CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y diff --git a/arch/arm/configs/ezx_defconfig b/arch/arm/configs/ezx_defconfig index 227a477346ed..d95763d5f0d8 100644 --- a/arch/arm/configs/ezx_defconfig +++ b/arch/arm/configs/ezx_defconfig @@ -287,7 +287,7 @@ CONFIG_USB=y # CONFIG_USB_DEVICE_CLASS is not set CONFIG_USB_OHCI_HCD=y CONFIG_USB_GADGET=y -CONFIG_USB_GADGET_PXA27X=y +CONFIG_USB_PXA27X=y CONFIG_USB_ETH=m # CONFIG_USB_ETH_RNDIS is not set CONFIG_MMC=y diff --git a/arch/arm/configs/imote2_defconfig b/arch/arm/configs/imote2_defconfig index 176ec22af034..fd996bb13022 100644 --- a/arch/arm/configs/imote2_defconfig +++ b/arch/arm/configs/imote2_defconfig @@ -263,7 +263,7 @@ CONFIG_USB=y # CONFIG_USB_DEVICE_CLASS is not set CONFIG_USB_OHCI_HCD=y CONFIG_USB_GADGET=y -CONFIG_USB_GADGET_PXA27X=y +CONFIG_USB_PXA27X=y CONFIG_USB_ETH=m # CONFIG_USB_ETH_RNDIS is not set CONFIG_MMC=y diff --git a/arch/arm/configs/magician_defconfig b/arch/arm/configs/magician_defconfig index a88e64d4e9a5..443675d317e6 100644 --- a/arch/arm/configs/magician_defconfig +++ b/arch/arm/configs/magician_defconfig @@ -132,7 +132,7 @@ CONFIG_USB_MON=m CONFIG_USB_OHCI_HCD=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_VBUS_DRAW=500 -CONFIG_USB_GADGET_PXA27X=y +CONFIG_USB_PXA27X=y CONFIG_USB_ETH=m # CONFIG_USB_ETH_RNDIS is not set CONFIG_USB_GADGETFS=m diff --git a/arch/arm/configs/omap1_defconfig b/arch/arm/configs/omap1_defconfig index 7b63462b349d..945a34f2a34d 100644 --- a/arch/arm/configs/omap1_defconfig +++ b/arch/arm/configs/omap1_defconfig @@ -48,13 +48,7 @@ CONFIG_MACH_SX1=y CONFIG_MACH_NOKIA770=y CONFIG_MACH_AMS_DELTA=y CONFIG_MACH_OMAP_GENERIC=y -CONFIG_OMAP_CLOCKS_SET_BY_BOOTLOADER=y -CONFIG_OMAP_ARM_216MHZ=y -CONFIG_OMAP_ARM_195MHZ=y -CONFIG_OMAP_ARM_192MHZ=y CONFIG_OMAP_ARM_182MHZ=y -CONFIG_OMAP_ARM_168MHZ=y -# CONFIG_OMAP_ARM_60MHZ is not set # CONFIG_ARM_THUMB is not set CONFIG_PCCARD=y CONFIG_OMAP_CF=y diff --git a/arch/arm/configs/pcontrol_g20_defconfig b/arch/arm/configs/pcontrol_g20_defconfig deleted file mode 100644 index c75c9fcede58..000000000000 --- a/arch/arm/configs/pcontrol_g20_defconfig +++ /dev/null @@ -1,175 +0,0 @@ -CONFIG_EXPERIMENTAL=y -CONFIG_CROSS_COMPILE="/opt/arm-2010q1/bin/arm-none-linux-gnueabi-" -# CONFIG_LOCALVERSION_AUTO is not set -# CONFIG_SWAP is not set -CONFIG_SYSVIPC=y -CONFIG_POSIX_MQUEUE=y -CONFIG_TREE_PREEMPT_RCU=y -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_LOG_BUF_SHIFT=14 -CONFIG_NAMESPACES=y -CONFIG_BLK_DEV_INITRD=y -CONFIG_EXPERT=y -# CONFIG_SYSCTL_SYSCALL is not set -# CONFIG_KALLSYMS is not set -# CONFIG_VM_EVENT_COUNTERS is not set -# CONFIG_COMPAT_BRK is not set -CONFIG_SLAB=y -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -# CONFIG_LBDAF is not set -# CONFIG_BLK_DEV_BSG is not set -CONFIG_DEFAULT_DEADLINE=y -CONFIG_ARCH_AT91=y -CONFIG_ARCH_AT91SAM9G20=y -CONFIG_MACH_PCONTROL_G20=y -CONFIG_AT91_PROGRAMMABLE_CLOCKS=y -CONFIG_NO_HZ=y -CONFIG_HIGH_RES_TIMERS=y -CONFIG_PREEMPT=y -CONFIG_AEABI=y -# CONFIG_OABI_COMPAT is not set -CONFIG_ZBOOT_ROM_TEXT=0x0 -CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="console=ttyS0,115200 mem=128M mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root) root=/dev/mmcblk0p1 rootwait rw" -CONFIG_VFP=y -CONFIG_BINFMT_MISC=y -CONFIG_NET=y -CONFIG_PACKET=y -CONFIG_UNIX=y -CONFIG_INET=y -# CONFIG_INET_XFRM_MODE_TRANSPORT is not set -# CONFIG_INET_XFRM_MODE_TUNNEL is not set -# CONFIG_INET_XFRM_MODE_BEET is not set -# CONFIG_INET_LRO is not set -# CONFIG_IPV6 is not set -CONFIG_VLAN_8021Q=y -# CONFIG_WIRELESS is not set -CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" -# CONFIG_FW_LOADER is not set -CONFIG_MTD=y -CONFIG_MTD_PARTITIONS=y -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_CHAR=y -CONFIG_MTD_BLOCK=y -CONFIG_MTD_COMPLEX_MAPPINGS=y -CONFIG_MTD_PHRAM=m -CONFIG_MTD_NAND=y -CONFIG_MTD_NAND_ATMEL=y -CONFIG_BLK_DEV_LOOP=y -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_SIZE=8192 -CONFIG_ATMEL_TCLIB=y -CONFIG_EEPROM_AT24=m -CONFIG_SCSI=m -# CONFIG_SCSI_PROC_FS is not set -CONFIG_BLK_DEV_SD=m -CONFIG_SCSI_MULTI_LUN=y -# CONFIG_SCSI_LOWLEVEL is not set -CONFIG_NETDEVICES=y -CONFIG_MACVLAN=m -CONFIG_TUN=m -CONFIG_SMSC_PHY=m -CONFIG_BROADCOM_PHY=m -CONFIG_NET_ETHERNET=y -CONFIG_MII=y -CONFIG_MACB=y -CONFIG_SMSC911X=m -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set -# CONFIG_WLAN is not set -CONFIG_PPP=m -CONFIG_PPP_ASYNC=m -CONFIG_PPP_DEFLATE=m -CONFIG_PPP_MPPE=m -CONFIG_INPUT_POLLDEV=y -CONFIG_INPUT_SPARSEKMAP=y -# CONFIG_INPUT_MOUSEDEV is not set -CONFIG_INPUT_EVDEV=m -CONFIG_INPUT_EVBUG=m -# CONFIG_KEYBOARD_ATKBD is not set -CONFIG_KEYBOARD_GPIO=m -CONFIG_KEYBOARD_MATRIX=m -# CONFIG_INPUT_MOUSE is not set -CONFIG_INPUT_TOUCHSCREEN=y -CONFIG_INPUT_MISC=y -CONFIG_INPUT_UINPUT=m -CONFIG_INPUT_GPIO_ROTARY_ENCODER=m -# CONFIG_SERIO is not set -# CONFIG_DEVKMEM is not set -CONFIG_SERIAL_ATMEL=y -CONFIG_SERIAL_ATMEL_CONSOLE=y -CONFIG_SERIAL_MAX3100=m -# CONFIG_LEGACY_PTYS is not set -# CONFIG_HW_RANDOM is not set -CONFIG_R3964=m -CONFIG_I2C=m -CONFIG_I2C_CHARDEV=m -# CONFIG_I2C_HELPER_AUTO is not set -CONFIG_I2C_GPIO=m -CONFIG_SPI=y -CONFIG_SPI_ATMEL=m -CONFIG_SPI_SPIDEV=m -CONFIG_GPIO_SYSFS=y -CONFIG_W1=m -CONFIG_W1_MASTER_GPIO=m -CONFIG_W1_SLAVE_DS2431=m -# CONFIG_HWMON is not set -CONFIG_WATCHDOG=y -CONFIG_AT91SAM9X_WATCHDOG=y -# CONFIG_MFD_SUPPORT is not set -# CONFIG_HID_SUPPORT is not set -CONFIG_USB=y -# CONFIG_USB_DEVICE_CLASS is not set -CONFIG_USB_OHCI_HCD=y -CONFIG_USB_STORAGE=m -CONFIG_USB_LIBUSUAL=y -CONFIG_USB_SERIAL=m -CONFIG_USB_SERIAL_GENERIC=y -CONFIG_USB_SERIAL_FTDI_SIO=m -CONFIG_USB_SERIAL_PL2303=m -CONFIG_USB_GADGET=y -CONFIG_USB_ZERO=m -CONFIG_USB_ETH=m -CONFIG_USB_FILE_STORAGE=m -CONFIG_USB_G_SERIAL=m -CONFIG_USB_G_HID=m -CONFIG_MMC=y -CONFIG_MMC_UNSAFE_RESUME=y -CONFIG_MMC_ATMELMCI=y -CONFIG_NEW_LEDS=y -CONFIG_LEDS_CLASS=y -CONFIG_LEDS_GPIO=y -CONFIG_LEDS_TRIGGERS=y -CONFIG_LEDS_TRIGGER_TIMER=y -CONFIG_LEDS_TRIGGER_HEARTBEAT=y -CONFIG_LEDS_TRIGGER_DEFAULT_ON=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_AT91SAM9=y -CONFIG_AUXDISPLAY=y -CONFIG_UIO=y -CONFIG_UIO_PDRV=y -CONFIG_STAGING=y -# CONFIG_STAGING_EXCLUDE_BUILD is not set -CONFIG_IIO=y -CONFIG_EXT2_FS=y -CONFIG_EXT3_FS=y -# CONFIG_EXT3_FS_XATTR is not set -CONFIG_VFAT_FS=y -CONFIG_TMPFS=y -CONFIG_JFFS2_FS=y -CONFIG_NFS_FS=y -CONFIG_NFS_V3=y -CONFIG_NFS_V4=y -CONFIG_PARTITION_ADVANCED=y -CONFIG_NLS_CODEPAGE_437=y -CONFIG_NLS_CODEPAGE_850=y -CONFIG_NLS_ISO8859_1=y -CONFIG_NLS_ISO8859_15=y -CONFIG_NLS_UTF8=y -# CONFIG_RCU_CPU_STALL_DETECTOR is not set -CONFIG_CRYPTO=y -CONFIG_CRYPTO_ANSI_CPRNG=y -# CONFIG_CRYPTO_HW is not set -CONFIG_CRC_CCITT=y diff --git a/arch/arm/configs/u300_defconfig b/arch/arm/configs/u300_defconfig index 4a5a12681be2..374000ec4e4e 100644 --- a/arch/arm/configs/u300_defconfig +++ b/arch/arm/configs/u300_defconfig @@ -14,8 +14,6 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_U300=y CONFIG_MACH_U300=y CONFIG_MACH_U300_BS335=y -CONFIG_MACH_U300_DUAL_RAM=y -CONFIG_U300_DEBUG=y CONFIG_MACH_U300_SPIDUMMY=y CONFIG_NO_HZ=y CONFIG_HIGH_RES_TIMERS=y @@ -26,19 +24,21 @@ CONFIG_ZBOOT_ROM_BSS=0x0 CONFIG_CMDLINE="root=/dev/ram0 rw rootfstype=rootfs console=ttyAMA0,115200n8 lpj=515072" CONFIG_CPU_IDLE=y CONFIG_FPE_NWFPE=y -CONFIG_PM=y # CONFIG_SUSPEND is not set CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" # CONFIG_PREVENT_FIRMWARE_BUILD is not set -# CONFIG_MISC_DEVICES is not set +CONFIG_MTD=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_FSMC=y # CONFIG_INPUT_MOUSEDEV is not set CONFIG_INPUT_EVDEV=y # CONFIG_KEYBOARD_ATKBD is not set # CONFIG_INPUT_MOUSE is not set # CONFIG_SERIO is not set +CONFIG_LEGACY_PTY_COUNT=16 CONFIG_SERIAL_AMBA_PL011=y CONFIG_SERIAL_AMBA_PL011_CONSOLE=y -CONFIG_LEGACY_PTY_COUNT=16 # CONFIG_HW_RANDOM is not set CONFIG_I2C=y # CONFIG_HWMON is not set @@ -51,6 +51,7 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y # CONFIG_HID_SUPPORT is not set # CONFIG_USB_SUPPORT is not set CONFIG_MMC=y +CONFIG_MMC_CLKGATE=y CONFIG_MMC_ARMMMCI=y CONFIG_RTC_CLASS=y # CONFIG_RTC_HCTOSYS is not set @@ -65,10 +66,8 @@ CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y CONFIG_PRINTK_TIME=y CONFIG_DEBUG_FS=y -CONFIG_DEBUG_KERNEL=y # CONFIG_SCHED_DEBUG is not set CONFIG_TIMER_STATS=y # CONFIG_DEBUG_PREEMPT is not set CONFIG_DEBUG_INFO=y -# CONFIG_RCU_CPU_STALL_DETECTOR is not set # CONFIG_CRC32 is not set diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig index 97d31a4663da..2d7b6e7b7271 100644 --- a/arch/arm/configs/u8500_defconfig +++ b/arch/arm/configs/u8500_defconfig @@ -10,7 +10,7 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_U8500=y CONFIG_UX500_SOC_DB5500=y CONFIG_UX500_SOC_DB8500=y -CONFIG_MACH_U8500=y +CONFIG_MACH_HREFV60=y CONFIG_MACH_SNOWBALL=y CONFIG_MACH_U5500=y CONFIG_NO_HZ=y @@ -24,6 +24,7 @@ CONFIG_CPU_FREQ=y CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y CONFIG_VFP=y CONFIG_NEON=y +CONFIG_PM_RUNTIME=y CONFIG_NET=y CONFIG_PACKET=y CONFIG_UNIX=y @@ -41,11 +42,8 @@ CONFIG_MISC_DEVICES=y CONFIG_AB8500_PWM=y CONFIG_SENSORS_BH1780=y CONFIG_NETDEVICES=y -CONFIG_SMSC_PHY=y -CONFIG_NET_ETHERNET=y CONFIG_SMSC911X=y -# CONFIG_NETDEV_1000 is not set -# CONFIG_NETDEV_10000 is not set +CONFIG_SMSC_PHY=y # CONFIG_WLAN is not set # CONFIG_INPUT_MOUSEDEV_PSAUX is not set CONFIG_INPUT_EVDEV=y @@ -72,15 +70,12 @@ CONFIG_SPI=y CONFIG_SPI_PL022=y CONFIG_GPIO_STMPE=y CONFIG_GPIO_TC3589X=y -# CONFIG_HWMON is not set CONFIG_MFD_STMPE=y CONFIG_MFD_TC3589X=y +CONFIG_AB5500_CORE=y CONFIG_AB8500_CORE=y CONFIG_REGULATOR_AB8500=y # CONFIG_HID_SUPPORT is not set -CONFIG_USB_MUSB_HDRC=y -CONFIG_USB_GADGET_MUSB_HDRC=y -CONFIG_MUSB_PIO_ONLY=y CONFIG_USB_GADGET=y CONFIG_AB8500_USB=y CONFIG_MMC=y @@ -97,6 +92,7 @@ CONFIG_DMADEVICES=y CONFIG_STE_DMA40=y CONFIG_STAGING=y CONFIG_TOUCHSCREEN_SYNAPTICS_I2C_RMI4=y +CONFIG_HSEM_U8500=y CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y diff --git a/arch/arm/configs/zeus_defconfig b/arch/arm/configs/zeus_defconfig index 59577ad3f4ef..547a3c1e59db 100644 --- a/arch/arm/configs/zeus_defconfig +++ b/arch/arm/configs/zeus_defconfig @@ -140,7 +140,7 @@ CONFIG_USB_SERIAL=m CONFIG_USB_SERIAL_GENERIC=y CONFIG_USB_SERIAL_MCT_U232=m CONFIG_USB_GADGET=m -CONFIG_USB_GADGET_PXA27X=y +CONFIG_USB_PXA27X=y CONFIG_USB_ETH=m CONFIG_USB_GADGETFS=m CONFIG_USB_FILE_STORAGE=m diff --git a/arch/arm/include/asm/pmu.h b/arch/arm/include/asm/pmu.h index 71d99b83cdb9..0bda22c094a6 100644 --- a/arch/arm/include/asm/pmu.h +++ b/arch/arm/include/asm/pmu.h @@ -55,16 +55,6 @@ reserve_pmu(enum arm_pmu_type type); extern void release_pmu(enum arm_pmu_type type); -/** - * init_pmu() - Initialise the PMU. - * - * Initialise the system ready for PMU enabling. This should typically set the - * IRQ affinity and nothing else. The users (oprofile/perf events etc) will do - * the actual hardware initialisation. - */ -extern int -init_pmu(enum arm_pmu_type type); - #else /* CONFIG_CPU_HAS_PMU */ #include <linux/err.h> diff --git a/arch/arm/include/asm/topology.h b/arch/arm/include/asm/topology.h index a7e457ed27c3..58b8b84adcd2 100644 --- a/arch/arm/include/asm/topology.h +++ b/arch/arm/include/asm/topology.h @@ -25,7 +25,7 @@ extern struct cputopo_arm cpu_topology[NR_CPUS]; void init_cpu_topology(void); void store_cpu_topology(unsigned int cpuid); -const struct cpumask *cpu_coregroup_mask(unsigned int cpu); +const struct cpumask *cpu_coregroup_mask(int cpu); #else diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S index 9ad50c4208ae..b145f16c91bc 100644 --- a/arch/arm/kernel/entry-armv.S +++ b/arch/arm/kernel/entry-armv.S @@ -497,7 +497,7 @@ ENDPROC(__und_usr) .popsection .pushsection __ex_table,"a" .long 1b, 4b -#if __LINUX_ARM_ARCH__ >= 7 +#if CONFIG_ARM_THUMB && __LINUX_ARM_ARCH__ >= 6 && CONFIG_CPU_V7 .long 2b, 4b .long 3b, 4b #endif diff --git a/arch/arm/kernel/kprobes-arm.c b/arch/arm/kernel/kprobes-arm.c index 9fe8910308af..8a30c89da70e 100644 --- a/arch/arm/kernel/kprobes-arm.c +++ b/arch/arm/kernel/kprobes-arm.c @@ -519,10 +519,12 @@ static const union decode_item arm_cccc_0000_____1001_table[] = { static const union decode_item arm_cccc_0001_____1001_table[] = { /* Synchronization primitives */ +#if __LINUX_ARM_ARCH__ < 6 + /* Deprecated on ARMv6 and may be UNDEFINED on v7 */ /* SMP/SWPB cccc 0001 0x00 xxxx xxxx xxxx 1001 xxxx */ DECODE_EMULATEX (0x0fb000f0, 0x01000090, emulate_rd12rn16rm0_rwflags_nopc, REGS(NOPC, NOPC, 0, 0, NOPC)), - +#endif /* LDREX/STREX{,D,B,H} cccc 0001 1xxx xxxx xxxx xxxx 1001 xxxx */ /* And unallocated instructions... */ DECODE_END diff --git a/arch/arm/kernel/kprobes-test-arm.c b/arch/arm/kernel/kprobes-test-arm.c index fc82de8bdcce..ba32b393b3f0 100644 --- a/arch/arm/kernel/kprobes-test-arm.c +++ b/arch/arm/kernel/kprobes-test-arm.c @@ -427,18 +427,25 @@ void kprobe_arm_test_cases(void) TEST_GROUP("Synchronization primitives") - /* - * Use hard coded constants for SWP instructions to avoid warnings - * about deprecated instructions. - */ - TEST_RP( ".word 0xe108e097 @ swp lr, r",7,VAL2,", [r",8,0,"]") - TEST_R( ".word 0x610d0091 @ swpvs r0, r",1,VAL1,", [sp]") - TEST_RP( ".word 0xe10cd09e @ swp sp, r",14,VAL2,", [r",12,13*4,"]") +#if __LINUX_ARM_ARCH__ < 6 + TEST_RP("swp lr, r",7,VAL2,", [r",8,0,"]") + TEST_R( "swpvs r0, r",1,VAL1,", [sp]") + TEST_RP("swp sp, r",14,VAL2,", [r",12,13*4,"]") +#else + TEST_UNSUPPORTED(".word 0xe108e097 @ swp lr, r7, [r8]") + TEST_UNSUPPORTED(".word 0x610d0091 @ swpvs r0, r1, [sp]") + TEST_UNSUPPORTED(".word 0xe10cd09e @ swp sp, r14 [r12]") +#endif TEST_UNSUPPORTED(".word 0xe102f091 @ swp pc, r1, [r2]") TEST_UNSUPPORTED(".word 0xe102009f @ swp r0, pc, [r2]") TEST_UNSUPPORTED(".word 0xe10f0091 @ swp r0, r1, [pc]") - TEST_RP( ".word 0xe148e097 @ swpb lr, r",7,VAL2,", [r",8,0,"]") - TEST_R( ".word 0x614d0091 @ swpvsb r0, r",1,VAL1,", [sp]") +#if __LINUX_ARM_ARCH__ < 6 + TEST_RP("swpb lr, r",7,VAL2,", [r",8,0,"]") + TEST_R( "swpvsb r0, r",1,VAL1,", [sp]") +#else + TEST_UNSUPPORTED(".word 0xe148e097 @ swpb lr, r7, [r8]") + TEST_UNSUPPORTED(".word 0x614d0091 @ swpvsb r0, r1, [sp]") +#endif TEST_UNSUPPORTED(".word 0xe142f091 @ swpb pc, r1, [r2]") TEST_UNSUPPORTED(".word 0xe1100090") /* Unallocated space */ @@ -550,7 +557,7 @@ void kprobe_arm_test_cases(void) TEST_RPR( "strccd r",8, VAL2,", [r",13,0, ", r",12,48,"]") TEST_RPR( "strd r",4, VAL1,", [r",2, 24,", r",3, 48,"]!") TEST_RPR( "strcsd r",12,VAL2,", [r",11,48,", -r",10,24,"]!") - TEST_RPR( "strd r",2, VAL1,", [r",3, 24,"], r",4,48,"") + TEST_RPR( "strd r",2, VAL1,", [r",5, 24,"], r",4,48,"") TEST_RPR( "strd r",10,VAL2,", [r",9, 48,"], -r",7,24,"") TEST_UNSUPPORTED(".word 0xe1afc0fa @ strd r12, [pc, r10]!") diff --git a/arch/arm/kernel/kprobes-test-thumb.c b/arch/arm/kernel/kprobes-test-thumb.c index 5e726c31c45a..5d8b85792222 100644 --- a/arch/arm/kernel/kprobes-test-thumb.c +++ b/arch/arm/kernel/kprobes-test-thumb.c @@ -222,8 +222,8 @@ void kprobe_thumb16_test_cases(void) DONT_TEST_IN_ITBLOCK( TEST_BF_R( "cbnz r",0,0, ", 2f") TEST_BF_R( "cbz r",2,-1,", 2f") - TEST_BF_RX( "cbnz r",4,1, ", 2f",0x20) - TEST_BF_RX( "cbz r",7,0, ", 2f",0x40) + TEST_BF_RX( "cbnz r",4,1, ", 2f", SPACE_0x20) + TEST_BF_RX( "cbz r",7,0, ", 2f", SPACE_0x40) ) TEST_R("sxth r0, r",7, HH1,"") TEST_R("sxth r7, r",0, HH2,"") @@ -246,7 +246,7 @@ DONT_TEST_IN_ITBLOCK( TESTCASE_START(code) \ TEST_ARG_PTR(13, offset) \ TEST_ARG_END("") \ - TEST_BRANCH_F(code,0) \ + TEST_BRANCH_F(code) \ TESTCASE_END TEST("push {r0}") @@ -319,8 +319,8 @@ CONDITION_INSTRUCTIONS(8, TEST_BF( "b 2f") TEST_BB( "b 2b") - TEST_BF_X("b 2f", 0x400) - TEST_BB_X("b 2b", 0x400) + TEST_BF_X("b 2f", SPACE_0x400) + TEST_BB_X("b 2b", SPACE_0x400) TEST_GROUP("Testing instructions in IT blocks") @@ -746,7 +746,7 @@ CONDITION_INSTRUCTIONS(22, TEST_BB("bne.w 2b") TEST_BF("bgt.w 2f") TEST_BB("blt.w 2b") - TEST_BF_X("bpl.w 2f",0x1000) + TEST_BF_X("bpl.w 2f", SPACE_0x1000) ) TEST_UNSUPPORTED("msr cpsr, r0") @@ -786,11 +786,11 @@ CONDITION_INSTRUCTIONS(22, TEST_BF( "b.w 2f") TEST_BB( "b.w 2b") - TEST_BF_X("b.w 2f", 0x1000) + TEST_BF_X("b.w 2f", SPACE_0x1000) TEST_BF( "bl.w 2f") TEST_BB( "bl.w 2b") - TEST_BB_X("bl.w 2b", 0x1000) + TEST_BB_X("bl.w 2b", SPACE_0x1000) TEST_X( "blx __dummy_arm_subroutine", ".arm \n\t" diff --git a/arch/arm/kernel/kprobes-test.h b/arch/arm/kernel/kprobes-test.h index 0dc5d77b9356..e28a869b1ae4 100644 --- a/arch/arm/kernel/kprobes-test.h +++ b/arch/arm/kernel/kprobes-test.h @@ -149,23 +149,31 @@ struct test_arg_end { "1: "instruction" \n\t" \ " nop \n\t" -#define TEST_BRANCH_F(instruction, xtra_dist) \ +#define TEST_BRANCH_F(instruction) \ TEST_INSTRUCTION(instruction) \ - ".if "#xtra_dist" \n\t" \ " b 99f \n\t" \ - ".space "#xtra_dist" \n\t" \ - ".endif \n\t" \ + "2: nop \n\t" + +#define TEST_BRANCH_B(instruction) \ + " b 50f \n\t" \ + " b 99f \n\t" \ + "2: nop \n\t" \ + " b 99f \n\t" \ + TEST_INSTRUCTION(instruction) + +#define TEST_BRANCH_FX(instruction, codex) \ + TEST_INSTRUCTION(instruction) \ + " b 99f \n\t" \ + codex" \n\t" \ " b 99f \n\t" \ "2: nop \n\t" -#define TEST_BRANCH_B(instruction, xtra_dist) \ +#define TEST_BRANCH_BX(instruction, codex) \ " b 50f \n\t" \ " b 99f \n\t" \ "2: nop \n\t" \ " b 99f \n\t" \ - ".if "#xtra_dist" \n\t" \ - ".space "#xtra_dist" \n\t" \ - ".endif \n\t" \ + codex" \n\t" \ TEST_INSTRUCTION(instruction) #define TESTCASE_END \ @@ -301,47 +309,60 @@ struct test_arg_end { TESTCASE_START(code1 #reg1 code2) \ TEST_ARG_PTR(reg1, val1) \ TEST_ARG_END("") \ - TEST_BRANCH_F(code1 #reg1 code2, 0) \ + TEST_BRANCH_F(code1 #reg1 code2) \ TESTCASE_END -#define TEST_BF_X(code, xtra_dist) \ +#define TEST_BF(code) \ TESTCASE_START(code) \ TEST_ARG_END("") \ - TEST_BRANCH_F(code, xtra_dist) \ + TEST_BRANCH_F(code) \ TESTCASE_END -#define TEST_BB_X(code, xtra_dist) \ +#define TEST_BB(code) \ TESTCASE_START(code) \ TEST_ARG_END("") \ - TEST_BRANCH_B(code, xtra_dist) \ + TEST_BRANCH_B(code) \ TESTCASE_END -#define TEST_BF_RX(code1, reg, val, code2, xtra_dist) \ - TESTCASE_START(code1 #reg code2) \ - TEST_ARG_REG(reg, val) \ - TEST_ARG_END("") \ - TEST_BRANCH_F(code1 #reg code2, xtra_dist) \ +#define TEST_BF_R(code1, reg, val, code2) \ + TESTCASE_START(code1 #reg code2) \ + TEST_ARG_REG(reg, val) \ + TEST_ARG_END("") \ + TEST_BRANCH_F(code1 #reg code2) \ TESTCASE_END -#define TEST_BB_RX(code1, reg, val, code2, xtra_dist) \ - TESTCASE_START(code1 #reg code2) \ - TEST_ARG_REG(reg, val) \ - TEST_ARG_END("") \ - TEST_BRANCH_B(code1 #reg code2, xtra_dist) \ +#define TEST_BB_R(code1, reg, val, code2) \ + TESTCASE_START(code1 #reg code2) \ + TEST_ARG_REG(reg, val) \ + TEST_ARG_END("") \ + TEST_BRANCH_B(code1 #reg code2) \ TESTCASE_END -#define TEST_BF(code) TEST_BF_X(code, 0) -#define TEST_BB(code) TEST_BB_X(code, 0) - -#define TEST_BF_R(code1, reg, val, code2) TEST_BF_RX(code1, reg, val, code2, 0) -#define TEST_BB_R(code1, reg, val, code2) TEST_BB_RX(code1, reg, val, code2, 0) - #define TEST_BF_RR(code1, reg1, val1, code2, reg2, val2, code3) \ TESTCASE_START(code1 #reg1 code2 #reg2 code3) \ TEST_ARG_REG(reg1, val1) \ TEST_ARG_REG(reg2, val2) \ TEST_ARG_END("") \ - TEST_BRANCH_F(code1 #reg1 code2 #reg2 code3, 0) \ + TEST_BRANCH_F(code1 #reg1 code2 #reg2 code3) \ + TESTCASE_END + +#define TEST_BF_X(code, codex) \ + TESTCASE_START(code) \ + TEST_ARG_END("") \ + TEST_BRANCH_FX(code, codex) \ + TESTCASE_END + +#define TEST_BB_X(code, codex) \ + TESTCASE_START(code) \ + TEST_ARG_END("") \ + TEST_BRANCH_BX(code, codex) \ + TESTCASE_END + +#define TEST_BF_RX(code1, reg, val, code2, codex) \ + TESTCASE_START(code1 #reg code2) \ + TEST_ARG_REG(reg, val) \ + TEST_ARG_END("") \ + TEST_BRANCH_FX(code1 #reg code2, codex) \ TESTCASE_END #define TEST_X(code, codex) \ @@ -372,6 +393,25 @@ struct test_arg_end { TESTCASE_END +/* + * Macros for defining space directives spread over multiple lines. + * These are required so the compiler guesses better the length of inline asm + * code and will spill the literal pool early enough to avoid generating PC + * relative loads with out of range offsets. + */ +#define TWICE(x) x x +#define SPACE_0x8 TWICE(".space 4\n\t") +#define SPACE_0x10 TWICE(SPACE_0x8) +#define SPACE_0x20 TWICE(SPACE_0x10) +#define SPACE_0x40 TWICE(SPACE_0x20) +#define SPACE_0x80 TWICE(SPACE_0x40) +#define SPACE_0x100 TWICE(SPACE_0x80) +#define SPACE_0x200 TWICE(SPACE_0x100) +#define SPACE_0x400 TWICE(SPACE_0x200) +#define SPACE_0x800 TWICE(SPACE_0x400) +#define SPACE_0x1000 TWICE(SPACE_0x800) + + /* Various values used in test cases... */ #define N(val) (val ^ 0xffffffff) #define VAL1 0x12345678 diff --git a/arch/arm/kernel/perf_event.c b/arch/arm/kernel/perf_event.c index 24e2347be6b1..8e9c98edc068 100644 --- a/arch/arm/kernel/perf_event.c +++ b/arch/arm/kernel/perf_event.c @@ -343,19 +343,25 @@ validate_group(struct perf_event *event) { struct perf_event *sibling, *leader = event->group_leader; struct pmu_hw_events fake_pmu; + DECLARE_BITMAP(fake_used_mask, ARMPMU_MAX_HWEVENTS); - memset(&fake_pmu, 0, sizeof(fake_pmu)); + /* + * Initialise the fake PMU. We only need to populate the + * used_mask for the purposes of validation. + */ + memset(fake_used_mask, 0, sizeof(fake_used_mask)); + fake_pmu.used_mask = fake_used_mask; if (!validate_event(&fake_pmu, leader)) - return -ENOSPC; + return -EINVAL; list_for_each_entry(sibling, &leader->sibling_list, group_entry) { if (!validate_event(&fake_pmu, sibling)) - return -ENOSPC; + return -EINVAL; } if (!validate_event(&fake_pmu, event)) - return -ENOSPC; + return -EINVAL; return 0; } @@ -396,6 +402,9 @@ armpmu_reserve_hardware(struct arm_pmu *armpmu) int i, err, irq, irqs; struct platform_device *pmu_device = armpmu->plat_device; + if (!pmu_device) + return -ENODEV; + err = reserve_pmu(armpmu->type); if (err) { pr_warning("unable to reserve pmu\n"); diff --git a/arch/arm/kernel/pmu.c b/arch/arm/kernel/pmu.c index 2c3407ee8576..2334bf8a650a 100644 --- a/arch/arm/kernel/pmu.c +++ b/arch/arm/kernel/pmu.c @@ -33,3 +33,4 @@ release_pmu(enum arm_pmu_type type) { clear_bit_unlock(type, pmu_lock); } +EXPORT_SYMBOL_GPL(release_pmu); diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c index 75316f0dd02a..3d0c6fb74ae4 100644 --- a/arch/arm/kernel/process.c +++ b/arch/arm/kernel/process.c @@ -192,6 +192,9 @@ void cpu_idle(void) #endif local_irq_disable(); +#ifdef CONFIG_PL310_ERRATA_769419 + wmb(); +#endif if (hlt_counter) { local_irq_enable(); cpu_relax(); diff --git a/arch/arm/kernel/topology.c b/arch/arm/kernel/topology.c index 1040c00405d0..8200deaa14f6 100644 --- a/arch/arm/kernel/topology.c +++ b/arch/arm/kernel/topology.c @@ -43,7 +43,7 @@ struct cputopo_arm cpu_topology[NR_CPUS]; -const struct cpumask *cpu_coregroup_mask(unsigned int cpu) +const struct cpumask *cpu_coregroup_mask(int cpu) { return &cpu_topology[cpu].core_sibling; } diff --git a/arch/arm/lib/bitops.h b/arch/arm/lib/bitops.h index 10d868a5a481..d6408d1ee543 100644 --- a/arch/arm/lib/bitops.h +++ b/arch/arm/lib/bitops.h @@ -1,5 +1,9 @@ +#include <asm/unwind.h> + #if __LINUX_ARM_ARCH__ >= 6 - .macro bitop, instr + .macro bitop, name, instr +ENTRY( \name ) +UNWIND( .fnstart ) ands ip, r1, #3 strneb r1, [ip] @ assert word-aligned mov r2, #1 @@ -13,9 +17,13 @@ cmp r0, #0 bne 1b bx lr +UNWIND( .fnend ) +ENDPROC(\name ) .endm - .macro testop, instr, store + .macro testop, name, instr, store +ENTRY( \name ) +UNWIND( .fnstart ) ands ip, r1, #3 strneb r1, [ip] @ assert word-aligned mov r2, #1 @@ -34,9 +42,13 @@ cmp r0, #0 movne r0, #1 2: bx lr +UNWIND( .fnend ) +ENDPROC(\name ) .endm #else - .macro bitop, instr + .macro bitop, name, instr +ENTRY( \name ) +UNWIND( .fnstart ) ands ip, r1, #3 strneb r1, [ip] @ assert word-aligned and r2, r0, #31 @@ -49,6 +61,8 @@ str r2, [r1, r0, lsl #2] restore_irqs ip mov pc, lr +UNWIND( .fnend ) +ENDPROC(\name ) .endm /** @@ -59,7 +73,9 @@ * Note: we can trivially conditionalise the store instruction * to avoid dirtying the data cache. */ - .macro testop, instr, store + .macro testop, name, instr, store +ENTRY( \name ) +UNWIND( .fnstart ) ands ip, r1, #3 strneb r1, [ip] @ assert word-aligned and r3, r0, #31 @@ -73,5 +89,7 @@ moveq r0, #0 restore_irqs ip mov pc, lr +UNWIND( .fnend ) +ENDPROC(\name ) .endm #endif diff --git a/arch/arm/lib/changebit.S b/arch/arm/lib/changebit.S index 68ed5b62e839..f4027862172f 100644 --- a/arch/arm/lib/changebit.S +++ b/arch/arm/lib/changebit.S @@ -12,6 +12,4 @@ #include "bitops.h" .text -ENTRY(_change_bit) - bitop eor -ENDPROC(_change_bit) +bitop _change_bit, eor diff --git a/arch/arm/lib/clearbit.S b/arch/arm/lib/clearbit.S index 4c04c3b51eeb..f6b75fb64d30 100644 --- a/arch/arm/lib/clearbit.S +++ b/arch/arm/lib/clearbit.S @@ -12,6 +12,4 @@ #include "bitops.h" .text -ENTRY(_clear_bit) - bitop bic -ENDPROC(_clear_bit) +bitop _clear_bit, bic diff --git a/arch/arm/lib/setbit.S b/arch/arm/lib/setbit.S index bbee5c66a23e..618fedae4b37 100644 --- a/arch/arm/lib/setbit.S +++ b/arch/arm/lib/setbit.S @@ -12,6 +12,4 @@ #include "bitops.h" .text -ENTRY(_set_bit) - bitop orr -ENDPROC(_set_bit) +bitop _set_bit, orr diff --git a/arch/arm/lib/testchangebit.S b/arch/arm/lib/testchangebit.S index 15a4d431f229..4becdc3a59cb 100644 --- a/arch/arm/lib/testchangebit.S +++ b/arch/arm/lib/testchangebit.S @@ -12,6 +12,4 @@ #include "bitops.h" .text -ENTRY(_test_and_change_bit) - testop eor, str -ENDPROC(_test_and_change_bit) +testop _test_and_change_bit, eor, str diff --git a/arch/arm/lib/testclearbit.S b/arch/arm/lib/testclearbit.S index 521b66b5b95d..918841dcce7a 100644 --- a/arch/arm/lib/testclearbit.S +++ b/arch/arm/lib/testclearbit.S @@ -12,6 +12,4 @@ #include "bitops.h" .text -ENTRY(_test_and_clear_bit) - testop bicne, strne -ENDPROC(_test_and_clear_bit) +testop _test_and_clear_bit, bicne, strne diff --git a/arch/arm/lib/testsetbit.S b/arch/arm/lib/testsetbit.S index 1c98cc2185bb..8d1b2fe9e487 100644 --- a/arch/arm/lib/testsetbit.S +++ b/arch/arm/lib/testsetbit.S @@ -12,6 +12,4 @@ #include "bitops.h" .text -ENTRY(_test_and_set_bit) - testop orreq, streq -ENDPROC(_test_and_set_bit) +testop _test_and_set_bit, orreq, streq diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index d111c3e99249..4f991f295284 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -3,6 +3,12 @@ if ARCH_AT91 config HAVE_AT91_DATAFLASH_CARD bool +config HAVE_AT91_DBGU0 + bool + +config HAVE_AT91_DBGU1 + bool + config HAVE_AT91_USART3 bool @@ -21,12 +27,14 @@ config ARCH_AT91RM9200 bool "AT91RM9200" select CPU_ARM920T select GENERIC_CLOCKEVENTS + select HAVE_AT91_DBGU0 select HAVE_AT91_USART3 config ARCH_AT91SAM9260 bool "AT91SAM9260 or AT91SAM9XE" select CPU_ARM926T select GENERIC_CLOCKEVENTS + select HAVE_AT91_DBGU0 select HAVE_AT91_USART3 select HAVE_AT91_USART4 select HAVE_AT91_USART5 @@ -37,11 +45,13 @@ config ARCH_AT91SAM9261 select CPU_ARM926T select GENERIC_CLOCKEVENTS select HAVE_FB_ATMEL + select HAVE_AT91_DBGU0 config ARCH_AT91SAM9G10 bool "AT91SAM9G10" select CPU_ARM926T select GENERIC_CLOCKEVENTS + select HAVE_AT91_DBGU0 select HAVE_FB_ATMEL config ARCH_AT91SAM9263 @@ -50,6 +60,7 @@ config ARCH_AT91SAM9263 select GENERIC_CLOCKEVENTS select HAVE_FB_ATMEL select HAVE_NET_MACB + select HAVE_AT91_DBGU1 config ARCH_AT91SAM9RL bool "AT91SAM9RL" @@ -57,11 +68,13 @@ config ARCH_AT91SAM9RL select GENERIC_CLOCKEVENTS select HAVE_AT91_USART3 select HAVE_FB_ATMEL + select HAVE_AT91_DBGU0 config ARCH_AT91SAM9G20 bool "AT91SAM9G20" select CPU_ARM926T select GENERIC_CLOCKEVENTS + select HAVE_AT91_DBGU0 select HAVE_AT91_USART3 select HAVE_AT91_USART4 select HAVE_AT91_USART5 @@ -74,6 +87,7 @@ config ARCH_AT91SAM9G45 select HAVE_AT91_USART3 select HAVE_FB_ATMEL select HAVE_NET_MACB + select HAVE_AT91_DBGU1 config ARCH_AT91CAP9 bool "AT91CAP9" @@ -81,6 +95,7 @@ config ARCH_AT91CAP9 select GENERIC_CLOCKEVENTS select HAVE_FB_ATMEL select HAVE_NET_MACB + select HAVE_AT91_DBGU1 config ARCH_AT91X40 bool "AT91x40" @@ -510,8 +525,13 @@ config AT91_TIMER_HZ choice prompt "Select a UART for early kernel messages" -config AT91_EARLY_DBGU - bool "DBGU" +config AT91_EARLY_DBGU0 + bool "DBGU on rm9200, 9260/9g20, 9261/9g10 and 9rl" + depends on HAVE_AT91_DBGU0 + +config AT91_EARLY_DBGU1 + bool "DBGU on 9263, 9g45 and cap9" + depends on HAVE_AT91_DBGU1 config AT91_EARLY_USART0 bool "USART0" diff --git a/arch/arm/mach-at91/at91cap9.c b/arch/arm/mach-at91/at91cap9.c index ecdd54dd68c6..506a26c3fff6 100644 --- a/arch/arm/mach-at91/at91cap9.c +++ b/arch/arm/mach-at91/at91cap9.c @@ -13,7 +13,6 @@ */ #include <linux/module.h> -#include <linux/pm.h> #include <asm/irq.h> #include <asm/mach/arch.h> @@ -23,11 +22,11 @@ #include <mach/at91cap9.h> #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> -#include <mach/at91_shdwc.h> #include "soc.h" #include "generic.h" #include "clock.h" +#include "sam9_smc.h" /* -------------------------------------------------------------------- * Clocks @@ -137,7 +136,7 @@ static struct clk pwm_clk = { .type = CLK_TYPE_PERIPHERAL, }; static struct clk macb_clk = { - .name = "macb_clk", + .name = "pclk", .pmc_mask = 1 << AT91CAP9_ID_EMAC, .type = CLK_TYPE_PERIPHERAL, }; @@ -210,6 +209,8 @@ static struct clk *periph_clocks[] __initdata = { }; static struct clk_lookup periph_clocks_lookups[] = { + /* One additional fake clock for macb_hclk */ + CLKDEV_CON_ID("hclk", &macb_clk), CLKDEV_CON_DEV_ID("hclk", "atmel_usba_udc", &utmi_clk), CLKDEV_CON_DEV_ID("pclk", "atmel_usba_udc", &udphs_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), @@ -221,6 +222,10 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk), + CLKDEV_CON_ID("pioA", &pioABCD_clk), + CLKDEV_CON_ID("pioB", &pioABCD_clk), + CLKDEV_CON_ID("pioC", &pioABCD_clk), + CLKDEV_CON_ID("pioD", &pioABCD_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -293,23 +298,19 @@ void __init at91cap9_set_console_clock(int id) * GPIO * -------------------------------------------------------------------- */ -static struct at91_gpio_bank at91cap9_gpio[] = { +static struct at91_gpio_bank at91cap9_gpio[] __initdata = { { .id = AT91CAP9_ID_PIOABCD, - .offset = AT91_PIOA, - .clock = &pioABCD_clk, + .regbase = AT91CAP9_BASE_PIOA, }, { .id = AT91CAP9_ID_PIOABCD, - .offset = AT91_PIOB, - .clock = &pioABCD_clk, + .regbase = AT91CAP9_BASE_PIOB, }, { .id = AT91CAP9_ID_PIOABCD, - .offset = AT91_PIOC, - .clock = &pioABCD_clk, + .regbase = AT91CAP9_BASE_PIOC, }, { .id = AT91CAP9_ID_PIOABCD, - .offset = AT91_PIOD, - .clock = &pioABCD_clk, + .regbase = AT91CAP9_BASE_PIOD, } }; @@ -318,12 +319,6 @@ static void at91cap9_reset(void) at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); } -static void at91cap9_poweroff(void) -{ - at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -} - - /* -------------------------------------------------------------------- * AT91CAP9 processor initialization * -------------------------------------------------------------------- */ @@ -333,10 +328,16 @@ static void __init at91cap9_map_io(void) at91_init_sram(0, AT91CAP9_SRAM_BASE, AT91CAP9_SRAM_SIZE); } +static void __init at91cap9_ioremap_registers(void) +{ + at91_ioremap_shdwc(AT91CAP9_BASE_SHDWC); + at91sam926x_ioremap_pit(AT91CAP9_BASE_PIT); + at91sam9_ioremap_smc(0, AT91CAP9_BASE_SMC); +} + static void __init at91cap9_initialize(void) { at91_arch_reset = at91cap9_reset; - pm_power_off = at91cap9_poweroff; at91_extern_irq = (1 << AT91CAP9_ID_IRQ0) | (1 << AT91CAP9_ID_IRQ1); /* Register GPIO subsystem */ @@ -394,6 +395,7 @@ static unsigned int at91cap9_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91cap9_soc = { .map_io = at91cap9_map_io, .default_irq_priority = at91cap9_default_irq_priority, + .ioremap_registers = at91cap9_ioremap_registers, .register_clocks = at91cap9_register_clocks, .init = at91cap9_initialize, }; diff --git a/arch/arm/mach-at91/at91cap9_devices.c b/arch/arm/mach-at91/at91cap9_devices.c index adad70db70eb..d298fb7cb210 100644 --- a/arch/arm/mach-at91/at91cap9_devices.c +++ b/arch/arm/mach-at91/at91cap9_devices.c @@ -76,7 +76,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) /* Enable VBus control for UHP ports */ for (i = 0; i < data->ports; i++) { - if (data->vbus_pin[i]) + if (gpio_is_valid(data->vbus_pin[i])) at91_set_gpio_output(data->vbus_pin[i], 0); } @@ -179,7 +179,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep); memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep)); - if (data && data->vbus_pin > 0) { + if (data && gpio_is_valid(data->vbus_pin)) { at91_set_gpio_input(data->vbus_pin, 0); at91_set_deglitch(data->vbus_pin, 1); usba_udc_data.pdata.vbus_pin = data->vbus_pin; @@ -200,7 +200,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) {} #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) static u64 eth_dmamask = DMA_BIT_MASK(32); -static struct at91_eth_data eth_data; +static struct macb_platform_data eth_data; static struct resource eth_resources[] = { [0] = { @@ -227,12 +227,12 @@ static struct platform_device at91cap9_eth_device = { .num_resources = ARRAY_SIZE(eth_resources), }; -void __init at91_add_device_eth(struct at91_eth_data *data) +void __init at91_add_device_eth(struct macb_platform_data *data) { if (!data) return; - if (data->phy_irq_pin) { + if (gpio_is_valid(data->phy_irq_pin)) { at91_set_gpio_input(data->phy_irq_pin, 0); at91_set_deglitch(data->phy_irq_pin, 1); } @@ -264,7 +264,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data) platform_device_register(&at91cap9_eth_device); } #else -void __init at91_add_device_eth(struct at91_eth_data *data) {} +void __init at91_add_device_eth(struct macb_platform_data *data) {} #endif @@ -332,13 +332,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) return; /* input/irq */ - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 1); at91_set_deglitch(data->det_pin, 1); } - if (data->wp_pin) + if (gpio_is_valid(data->wp_pin)) at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) at91_set_gpio_output(data->vcc_pin, 0); if (mmc_id == 0) { /* MCI0 */ @@ -398,8 +398,8 @@ static struct resource nand_resources[] = { .flags = IORESOURCE_MEM, }, [1] = { - .start = AT91_BASE_SYS + AT91_ECC, - .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1, + .start = AT91CAP9_BASE_ECC, + .end = AT91CAP9_BASE_ECC + SZ_512 - 1, .flags = IORESOURCE_MEM, } }; @@ -425,15 +425,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA); /* enable pin */ - if (data->enable_pin) + if (gpio_is_valid(data->enable_pin)) at91_set_gpio_output(data->enable_pin, 1); /* ready/busy pin */ - if (data->rdy_pin) + if (gpio_is_valid(data->rdy_pin)) at91_set_gpio_input(data->rdy_pin, 1); /* card detect pin */ - if (data->det_pin) + if (gpio_is_valid(data->det_pin)) at91_set_gpio_input(data->det_pin, 1); nand_data = *data; @@ -670,8 +670,8 @@ static void __init at91_add_device_tc(void) { } static struct resource rtt_resources[] = { { - .start = AT91_BASE_SYS + AT91_RTT, - .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1, + .start = AT91CAP9_BASE_RTT, + .end = AT91CAP9_BASE_RTT + SZ_16 - 1, .flags = IORESOURCE_MEM, } }; @@ -694,10 +694,19 @@ static void __init at91_add_device_rtt(void) * -------------------------------------------------------------------- */ #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE) +static struct resource wdt_resources[] = { + { + .start = AT91CAP9_BASE_WDT, + .end = AT91CAP9_BASE_WDT + SZ_16 - 1, + .flags = IORESOURCE_MEM, + } +}; + static struct platform_device at91cap9_wdt_device = { .name = "at91_wdt", .id = -1, - .num_resources = 0, + .resource = wdt_resources, + .num_resources = ARRAY_SIZE(wdt_resources), }; static void __init at91_add_device_watchdog(void) @@ -807,7 +816,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) at91_set_A_periph(AT91_PIN_PA9, 0); /* AC97RX */ /* reset */ - if (data->reset_pin) + if (gpio_is_valid(data->reset_pin)) at91_set_gpio_output(data->reset_pin, 0); ac97_data = *data; @@ -1021,8 +1030,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {} #if defined(CONFIG_SERIAL_ATMEL) static struct resource dbgu_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DBGU, - .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .start = AT91CAP9_BASE_DBGU, + .end = AT91CAP9_BASE_DBGU + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { diff --git a/arch/arm/mach-at91/at91rm9200.c b/arch/arm/mach-at91/at91rm9200.c index 713d3bdbd284..9163d7d5f76e 100644 --- a/arch/arm/mach-at91/at91rm9200.c +++ b/arch/arm/mach-at91/at91rm9200.c @@ -23,6 +23,7 @@ #include "soc.h" #include "generic.h" #include "clock.h" +#include "sam9_smc.h" static struct map_desc at91rm9200_io_desc[] __initdata = { { @@ -195,6 +196,10 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk), + CLKDEV_CON_ID("pioA", &pioA_clk), + CLKDEV_CON_ID("pioB", &pioB_clk), + CLKDEV_CON_ID("pioC", &pioC_clk), + CLKDEV_CON_ID("pioD", &pioD_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -268,23 +273,19 @@ void __init at91rm9200_set_console_clock(int id) * GPIO * -------------------------------------------------------------------- */ -static struct at91_gpio_bank at91rm9200_gpio[] = { +static struct at91_gpio_bank at91rm9200_gpio[] __initdata = { { .id = AT91RM9200_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, + .regbase = AT91RM9200_BASE_PIOA, }, { .id = AT91RM9200_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, + .regbase = AT91RM9200_BASE_PIOB, }, { .id = AT91RM9200_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, + .regbase = AT91RM9200_BASE_PIOC, }, { .id = AT91RM9200_ID_PIOD, - .offset = AT91_PIOD, - .clock = &pioD_clk, + .regbase = AT91RM9200_BASE_PIOD, } }; @@ -307,6 +308,10 @@ static void __init at91rm9200_map_io(void) iotable_init(at91rm9200_io_desc, ARRAY_SIZE(at91rm9200_io_desc)); } +static void __init at91rm9200_ioremap_registers(void) +{ +} + static void __init at91rm9200_initialize(void) { at91_arch_reset = at91rm9200_reset; @@ -366,6 +371,7 @@ static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91rm9200_soc = { .map_io = at91rm9200_map_io, .default_irq_priority = at91rm9200_default_irq_priority, + .ioremap_registers = at91rm9200_ioremap_registers, .register_clocks = at91rm9200_register_clocks, .init = at91rm9200_initialize, }; diff --git a/arch/arm/mach-at91/at91rm9200_devices.c b/arch/arm/mach-at91/at91rm9200_devices.c index 66591fa53e05..18bacec2b094 100644 --- a/arch/arm/mach-at91/at91rm9200_devices.c +++ b/arch/arm/mach-at91/at91rm9200_devices.c @@ -83,7 +83,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {} * USB Device (Gadget) * -------------------------------------------------------------------- */ -#ifdef CONFIG_USB_GADGET_AT91 +#ifdef CONFIG_USB_AT91 static struct at91_udc_data udc_data; static struct resource udc_resources[] = { @@ -114,11 +114,11 @@ void __init at91_add_device_udc(struct at91_udc_data *data) if (!data) return; - if (data->vbus_pin) { + if (gpio_is_valid(data->vbus_pin)) { at91_set_gpio_input(data->vbus_pin, 0); at91_set_deglitch(data->vbus_pin, 1); } - if (data->pullup_pin) + if (gpio_is_valid(data->pullup_pin)) at91_set_gpio_output(data->pullup_pin, 0); udc_data = *data; @@ -135,7 +135,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {} #if defined(CONFIG_ARM_AT91_ETHER) || defined(CONFIG_ARM_AT91_ETHER_MODULE) static u64 eth_dmamask = DMA_BIT_MASK(32); -static struct at91_eth_data eth_data; +static struct macb_platform_data eth_data; static struct resource eth_resources[] = { [0] = { @@ -162,12 +162,12 @@ static struct platform_device at91rm9200_eth_device = { .num_resources = ARRAY_SIZE(eth_resources), }; -void __init at91_add_device_eth(struct at91_eth_data *data) +void __init at91_add_device_eth(struct macb_platform_data *data) { if (!data) return; - if (data->phy_irq_pin) { + if (gpio_is_valid(data->phy_irq_pin)) { at91_set_gpio_input(data->phy_irq_pin, 0); at91_set_deglitch(data->phy_irq_pin, 1); } @@ -199,7 +199,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data) platform_device_register(&at91rm9200_eth_device); } #else -void __init at91_add_device_eth(struct at91_eth_data *data) {} +void __init at91_add_device_eth(struct macb_platform_data *data) {} #endif @@ -260,7 +260,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data) ); /* input/irq */ - if (data->irq_pin) { + if (gpio_is_valid(data->irq_pin)) { at91_set_gpio_input(data->irq_pin, 1); at91_set_deglitch(data->irq_pin, 1); } @@ -268,7 +268,7 @@ void __init at91_add_device_cf(struct at91_cf_data *data) at91_set_deglitch(data->det_pin, 1); /* outputs, initially off */ - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) at91_set_gpio_output(data->vcc_pin, 0); at91_set_gpio_output(data->rst_pin, 0); @@ -328,13 +328,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) return; /* input/irq */ - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 1); at91_set_deglitch(data->det_pin, 1); } - if (data->wp_pin) + if (gpio_is_valid(data->wp_pin)) at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) at91_set_gpio_output(data->vcc_pin, 0); /* CLK */ @@ -419,15 +419,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data) ); /* enable pin */ - if (data->enable_pin) + if (gpio_is_valid(data->enable_pin)) at91_set_gpio_output(data->enable_pin, 1); /* ready/busy pin */ - if (data->rdy_pin) + if (gpio_is_valid(data->rdy_pin)) at91_set_gpio_input(data->rdy_pin, 1); /* card detect pin */ - if (data->det_pin) + if (gpio_is_valid(data->det_pin)) at91_set_gpio_input(data->det_pin, 1); at91_set_A_periph(AT91_PIN_PC1, 0); /* SMOE */ @@ -665,10 +665,24 @@ static void __init at91_add_device_tc(void) { } * -------------------------------------------------------------------- */ #if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE) +static struct resource rtc_resources[] = { + [0] = { + .start = AT91RM9200_BASE_RTC, + .end = AT91RM9200_BASE_RTC + SZ_256 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_SYS, + .end = AT91_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + static struct platform_device at91rm9200_rtc_device = { .name = "at91_rtc", .id = -1, - .num_resources = 0, + .resource = rtc_resources, + .num_resources = ARRAY_SIZE(rtc_resources), }; static void __init at91_add_device_rtc(void) @@ -877,8 +891,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {} #if defined(CONFIG_SERIAL_ATMEL) static struct resource dbgu_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DBGU, - .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .start = AT91RM9200_BASE_DBGU, + .end = AT91RM9200_BASE_DBGU + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { diff --git a/arch/arm/mach-at91/at91rm9200_time.c b/arch/arm/mach-at91/at91rm9200_time.c index 1dd69c85dfec..a028cdf8f974 100644 --- a/arch/arm/mach-at91/at91rm9200_time.c +++ b/arch/arm/mach-at91/at91rm9200_time.c @@ -32,6 +32,8 @@ static unsigned long last_crtr; static u32 irqmask; static struct clock_event_device clkevt; +#define RM9200_TIMER_LATCH ((AT91_SLOW_CLOCK + HZ/2) / HZ) + /* * The ST_CRTR is updated asynchronously to the master clock ... but * the updates as seen by the CPU don't seem to be strictly monotonic. @@ -74,8 +76,8 @@ static irqreturn_t at91rm9200_timer_interrupt(int irq, void *dev_id) if (sr & AT91_ST_PITS) { u32 crtr = read_CRTR(); - while (((crtr - last_crtr) & AT91_ST_CRTV) >= LATCH) { - last_crtr += LATCH; + while (((crtr - last_crtr) & AT91_ST_CRTV) >= RM9200_TIMER_LATCH) { + last_crtr += RM9200_TIMER_LATCH; clkevt.event_handler(&clkevt); } return IRQ_HANDLED; @@ -116,7 +118,7 @@ clkevt32k_mode(enum clock_event_mode mode, struct clock_event_device *dev) case CLOCK_EVT_MODE_PERIODIC: /* PIT for periodic irqs; fixed rate of 1/HZ */ irqmask = AT91_ST_PITS; - at91_sys_write(AT91_ST_PIMR, LATCH); + at91_sys_write(AT91_ST_PIMR, RM9200_TIMER_LATCH); break; case CLOCK_EVT_MODE_ONESHOT: /* ALM for oneshot irqs, set by next_event() diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index b84a9f642f59..3a960d2740b6 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -11,7 +11,6 @@ */ #include <linux/module.h> -#include <linux/pm.h> #include <asm/irq.h> #include <asm/mach/arch.h> @@ -21,11 +20,11 @@ #include <mach/at91sam9260.h> #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> -#include <mach/at91_shdwc.h> #include "soc.h" #include "generic.h" #include "clock.h" +#include "sam9_smc.h" /* -------------------------------------------------------------------- * Clocks @@ -120,7 +119,7 @@ static struct clk ohci_clk = { .type = CLK_TYPE_PERIPHERAL, }; static struct clk macb_clk = { - .name = "macb_clk", + .name = "pclk", .pmc_mask = 1 << AT91SAM9260_ID_EMAC, .type = CLK_TYPE_PERIPHERAL, }; @@ -190,14 +189,16 @@ static struct clk *periph_clocks[] __initdata = { }; static struct clk_lookup periph_clocks_lookups[] = { + /* One additional fake clock for macb_hclk */ + CLKDEV_CON_ID("hclk", &macb_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk), CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk), CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tc0_clk), CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.0", &tc1_clk), CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk), - CLKDEV_CON_DEV_ID("t3_clk", "atmel_tcb.1", &tc3_clk), - CLKDEV_CON_DEV_ID("t4_clk", "atmel_tcb.1", &tc4_clk), - CLKDEV_CON_DEV_ID("t5_clk", "atmel_tcb.1", &tc5_clk), + CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.1", &tc3_clk), + CLKDEV_CON_DEV_ID("t1_clk", "atmel_tcb.1", &tc4_clk), + CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.1", &tc5_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc_clk), /* more usart lookup table for DT entries */ CLKDEV_CON_DEV_ID("usart", "fffff200.serial", &mck), @@ -209,6 +210,9 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("usart", "fffd8000.serial", &usart5_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk), + CLKDEV_CON_ID("pioA", &pioA_clk), + CLKDEV_CON_ID("pioB", &pioB_clk), + CLKDEV_CON_ID("pioC", &pioC_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -270,28 +274,19 @@ void __init at91sam9260_set_console_clock(int id) * GPIO * -------------------------------------------------------------------- */ -static struct at91_gpio_bank at91sam9260_gpio[] = { +static struct at91_gpio_bank at91sam9260_gpio[] __initdata = { { .id = AT91SAM9260_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, + .regbase = AT91SAM9260_BASE_PIOA, }, { .id = AT91SAM9260_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, + .regbase = AT91SAM9260_BASE_PIOB, }, { .id = AT91SAM9260_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, + .regbase = AT91SAM9260_BASE_PIOC, } }; -static void at91sam9260_poweroff(void) -{ - at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -} - - /* -------------------------------------------------------------------- * AT91SAM9260 processor initialization * -------------------------------------------------------------------- */ @@ -325,10 +320,16 @@ static void __init at91sam9260_map_io(void) } } +static void __init at91sam9260_ioremap_registers(void) +{ + at91_ioremap_shdwc(AT91SAM9260_BASE_SHDWC); + at91sam926x_ioremap_pit(AT91SAM9260_BASE_PIT); + at91sam9_ioremap_smc(0, AT91SAM9260_BASE_SMC); +} + static void __init at91sam9260_initialize(void) { at91_arch_reset = at91sam9_alt_reset; - pm_power_off = at91sam9260_poweroff; at91_extern_irq = (1 << AT91SAM9260_ID_IRQ0) | (1 << AT91SAM9260_ID_IRQ1) | (1 << AT91SAM9260_ID_IRQ2); @@ -381,6 +382,7 @@ static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91sam9260_soc = { .map_io = at91sam9260_map_io, .default_irq_priority = at91sam9260_default_irq_priority, + .ioremap_registers = at91sam9260_ioremap_registers, .register_clocks = at91sam9260_register_clocks, .init = at91sam9260_initialize, }; diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c index 25e3464fb07f..642ccb6d26b2 100644 --- a/arch/arm/mach-at91/at91sam9260_devices.c +++ b/arch/arm/mach-at91/at91sam9260_devices.c @@ -84,7 +84,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {} * USB Device (Gadget) * -------------------------------------------------------------------- */ -#ifdef CONFIG_USB_GADGET_AT91 +#ifdef CONFIG_USB_AT91 static struct at91_udc_data udc_data; static struct resource udc_resources[] = { @@ -115,7 +115,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) if (!data) return; - if (data->vbus_pin) { + if (gpio_is_valid(data->vbus_pin)) { at91_set_gpio_input(data->vbus_pin, 0); at91_set_deglitch(data->vbus_pin, 1); } @@ -136,7 +136,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {} #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) static u64 eth_dmamask = DMA_BIT_MASK(32); -static struct at91_eth_data eth_data; +static struct macb_platform_data eth_data; static struct resource eth_resources[] = { [0] = { @@ -163,12 +163,12 @@ static struct platform_device at91sam9260_eth_device = { .num_resources = ARRAY_SIZE(eth_resources), }; -void __init at91_add_device_eth(struct at91_eth_data *data) +void __init at91_add_device_eth(struct macb_platform_data *data) { if (!data) return; - if (data->phy_irq_pin) { + if (gpio_is_valid(data->phy_irq_pin)) { at91_set_gpio_input(data->phy_irq_pin, 0); at91_set_deglitch(data->phy_irq_pin, 1); } @@ -200,7 +200,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data) platform_device_register(&at91sam9260_eth_device); } #else -void __init at91_add_device_eth(struct at91_eth_data *data) {} +void __init at91_add_device_eth(struct macb_platform_data *data) {} #endif @@ -243,13 +243,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) return; /* input/irq */ - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 1); at91_set_deglitch(data->det_pin, 1); } - if (data->wp_pin) + if (gpio_is_valid(data->wp_pin)) at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) at91_set_gpio_output(data->vcc_pin, 0); /* CLK */ @@ -330,11 +330,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) { if (data->slot[i].bus_width) { /* input/irq */ - if (data->slot[i].detect_pin) { + if (gpio_is_valid(data->slot[i].detect_pin)) { at91_set_gpio_input(data->slot[i].detect_pin, 1); at91_set_deglitch(data->slot[i].detect_pin, 1); } - if (data->slot[i].wp_pin) + if (gpio_is_valid(data->slot[i].wp_pin)) at91_set_gpio_input(data->slot[i].wp_pin, 1); switch (i) { @@ -399,8 +399,8 @@ static struct resource nand_resources[] = { .flags = IORESOURCE_MEM, }, [1] = { - .start = AT91_BASE_SYS + AT91_ECC, - .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1, + .start = AT91SAM9260_BASE_ECC, + .end = AT91SAM9260_BASE_ECC + SZ_512 - 1, .flags = IORESOURCE_MEM, } }; @@ -426,15 +426,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); /* enable pin */ - if (data->enable_pin) + if (gpio_is_valid(data->enable_pin)) at91_set_gpio_output(data->enable_pin, 1); /* ready/busy pin */ - if (data->rdy_pin) + if (gpio_is_valid(data->rdy_pin)) at91_set_gpio_input(data->rdy_pin, 1); /* card detect pin */ - if (data->det_pin) + if (gpio_is_valid(data->det_pin)) at91_set_gpio_input(data->det_pin, 1); nand_data = *data; @@ -714,8 +714,8 @@ static void __init at91_add_device_tc(void) { } static struct resource rtt_resources[] = { { - .start = AT91_BASE_SYS + AT91_RTT, - .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1, + .start = AT91SAM9260_BASE_RTT, + .end = AT91SAM9260_BASE_RTT + SZ_16 - 1, .flags = IORESOURCE_MEM, } }; @@ -738,10 +738,19 @@ static void __init at91_add_device_rtt(void) * -------------------------------------------------------------------- */ #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE) +static struct resource wdt_resources[] = { + { + .start = AT91SAM9260_BASE_WDT, + .end = AT91SAM9260_BASE_WDT + SZ_16 - 1, + .flags = IORESOURCE_MEM, + } +}; + static struct platform_device at91sam9260_wdt_device = { .name = "at91_wdt", .id = -1, - .num_resources = 0, + .resource = wdt_resources, + .num_resources = ARRAY_SIZE(wdt_resources), }; static void __init at91_add_device_watchdog(void) @@ -837,8 +846,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {} #if defined(CONFIG_SERIAL_ATMEL) static struct resource dbgu_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DBGU, - .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .start = AT91SAM9260_BASE_DBGU, + .end = AT91SAM9260_BASE_DBGU + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { @@ -1281,17 +1290,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa); - if (data->rst_pin) { + if (gpio_is_valid(data->rst_pin)) { at91_set_multi_drive(data->rst_pin, 0); at91_set_gpio_output(data->rst_pin, 1); } - if (data->irq_pin) { + if (gpio_is_valid(data->irq_pin)) { at91_set_gpio_input(data->irq_pin, 0); at91_set_deglitch(data->irq_pin, 1); } - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 0); at91_set_deglitch(data->det_pin, 1); } diff --git a/arch/arm/mach-at91/at91sam9261.c b/arch/arm/mach-at91/at91sam9261.c index 658a5185abfd..a0538c5c2520 100644 --- a/arch/arm/mach-at91/at91sam9261.c +++ b/arch/arm/mach-at91/at91sam9261.c @@ -11,7 +11,6 @@ */ #include <linux/module.h> -#include <linux/pm.h> #include <asm/irq.h> #include <asm/mach/arch.h> @@ -20,11 +19,11 @@ #include <mach/at91sam9261.h> #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> -#include <mach/at91_shdwc.h> #include "soc.h" #include "generic.h" #include "clock.h" +#include "sam9_smc.h" /* -------------------------------------------------------------------- * Clocks @@ -176,6 +175,9 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.2", &ssc2_clk), CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &hck0), + CLKDEV_CON_ID("pioA", &pioA_clk), + CLKDEV_CON_ID("pioB", &pioB_clk), + CLKDEV_CON_ID("pioC", &pioC_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -251,28 +253,19 @@ void __init at91sam9261_set_console_clock(int id) * GPIO * -------------------------------------------------------------------- */ -static struct at91_gpio_bank at91sam9261_gpio[] = { +static struct at91_gpio_bank at91sam9261_gpio[] __initdata = { { .id = AT91SAM9261_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, + .regbase = AT91SAM9261_BASE_PIOA, }, { .id = AT91SAM9261_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, + .regbase = AT91SAM9261_BASE_PIOB, }, { .id = AT91SAM9261_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, + .regbase = AT91SAM9261_BASE_PIOC, } }; -static void at91sam9261_poweroff(void) -{ - at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -} - - /* -------------------------------------------------------------------- * AT91SAM9261 processor initialization * -------------------------------------------------------------------- */ @@ -285,10 +278,16 @@ static void __init at91sam9261_map_io(void) at91_init_sram(0, AT91SAM9261_SRAM_BASE, AT91SAM9261_SRAM_SIZE); } +static void __init at91sam9261_ioremap_registers(void) +{ + at91_ioremap_shdwc(AT91SAM9261_BASE_SHDWC); + at91sam926x_ioremap_pit(AT91SAM9261_BASE_PIT); + at91sam9_ioremap_smc(0, AT91SAM9261_BASE_SMC); +} + static void __init at91sam9261_initialize(void) { at91_arch_reset = at91sam9_alt_reset; - pm_power_off = at91sam9261_poweroff; at91_extern_irq = (1 << AT91SAM9261_ID_IRQ0) | (1 << AT91SAM9261_ID_IRQ1) | (1 << AT91SAM9261_ID_IRQ2); @@ -341,6 +340,7 @@ static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91sam9261_soc = { .map_io = at91sam9261_map_io, .default_irq_priority = at91sam9261_default_irq_priority, + .ioremap_registers = at91sam9261_ioremap_registers, .register_clocks = at91sam9261_register_clocks, .init = at91sam9261_initialize, }; diff --git a/arch/arm/mach-at91/at91sam9261_devices.c b/arch/arm/mach-at91/at91sam9261_devices.c index ae78f4d03b73..fc59cbdb0e3c 100644 --- a/arch/arm/mach-at91/at91sam9261_devices.c +++ b/arch/arm/mach-at91/at91sam9261_devices.c @@ -87,7 +87,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {} * USB Device (Gadget) * -------------------------------------------------------------------- */ -#ifdef CONFIG_USB_GADGET_AT91 +#ifdef CONFIG_USB_AT91 static struct at91_udc_data udc_data; static struct resource udc_resources[] = { @@ -118,7 +118,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) if (!data) return; - if (data->vbus_pin) { + if (gpio_is_valid(data->vbus_pin)) { at91_set_gpio_input(data->vbus_pin, 0); at91_set_deglitch(data->vbus_pin, 1); } @@ -171,13 +171,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) return; /* input/irq */ - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 1); at91_set_deglitch(data->det_pin, 1); } - if (data->wp_pin) + if (gpio_is_valid(data->wp_pin)) at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) at91_set_gpio_output(data->vcc_pin, 0); /* CLK */ @@ -240,15 +240,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); /* enable pin */ - if (data->enable_pin) + if (gpio_is_valid(data->enable_pin)) at91_set_gpio_output(data->enable_pin, 1); /* ready/busy pin */ - if (data->rdy_pin) + if (gpio_is_valid(data->rdy_pin)) at91_set_gpio_input(data->rdy_pin, 1); /* card detect pin */ - if (data->det_pin) + if (gpio_is_valid(data->det_pin)) at91_set_gpio_input(data->det_pin, 1); at91_set_A_periph(AT91_PIN_PC0, 0); /* NANDOE */ @@ -600,8 +600,8 @@ static void __init at91_add_device_tc(void) { } static struct resource rtt_resources[] = { { - .start = AT91_BASE_SYS + AT91_RTT, - .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1, + .start = AT91SAM9261_BASE_RTT, + .end = AT91SAM9261_BASE_RTT + SZ_16 - 1, .flags = IORESOURCE_MEM, } }; @@ -624,10 +624,19 @@ static void __init at91_add_device_rtt(void) * -------------------------------------------------------------------- */ #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE) +static struct resource wdt_resources[] = { + { + .start = AT91SAM9261_BASE_WDT, + .end = AT91SAM9261_BASE_WDT + SZ_16 - 1, + .flags = IORESOURCE_MEM, + } +}; + static struct platform_device at91sam9261_wdt_device = { .name = "at91_wdt", .id = -1, - .num_resources = 0, + .resource = wdt_resources, + .num_resources = ARRAY_SIZE(wdt_resources), }; static void __init at91_add_device_watchdog(void) @@ -816,8 +825,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {} #if defined(CONFIG_SERIAL_ATMEL) static struct resource dbgu_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DBGU, - .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .start = AT91SAM9261_BASE_DBGU, + .end = AT91SAM9261_BASE_DBGU + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { diff --git a/arch/arm/mach-at91/at91sam9263.c b/arch/arm/mach-at91/at91sam9263.c index f83fbb0ee0c5..5ffbbb024c1e 100644 --- a/arch/arm/mach-at91/at91sam9263.c +++ b/arch/arm/mach-at91/at91sam9263.c @@ -11,7 +11,6 @@ */ #include <linux/module.h> -#include <linux/pm.h> #include <asm/irq.h> #include <asm/mach/arch.h> @@ -19,11 +18,11 @@ #include <mach/at91sam9263.h> #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> -#include <mach/at91_shdwc.h> #include "soc.h" #include "generic.h" #include "clock.h" +#include "sam9_smc.h" /* -------------------------------------------------------------------- * Clocks @@ -118,7 +117,7 @@ static struct clk pwm_clk = { .type = CLK_TYPE_PERIPHERAL, }; static struct clk macb_clk = { - .name = "macb_clk", + .name = "pclk", .pmc_mask = 1 << AT91SAM9263_ID_EMAC, .type = CLK_TYPE_PERIPHERAL, }; @@ -182,6 +181,8 @@ static struct clk *periph_clocks[] __initdata = { }; static struct clk_lookup periph_clocks_lookups[] = { + /* One additional fake clock for macb_hclk */ + CLKDEV_CON_ID("hclk", &macb_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk), @@ -191,6 +192,11 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk), + CLKDEV_CON_ID("pioA", &pioA_clk), + CLKDEV_CON_ID("pioB", &pioB_clk), + CLKDEV_CON_ID("pioC", &pioCDE_clk), + CLKDEV_CON_ID("pioD", &pioCDE_clk), + CLKDEV_CON_ID("pioE", &pioCDE_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -263,36 +269,25 @@ void __init at91sam9263_set_console_clock(int id) * GPIO * -------------------------------------------------------------------- */ -static struct at91_gpio_bank at91sam9263_gpio[] = { +static struct at91_gpio_bank at91sam9263_gpio[] __initdata = { { .id = AT91SAM9263_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, + .regbase = AT91SAM9263_BASE_PIOA, }, { .id = AT91SAM9263_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, + .regbase = AT91SAM9263_BASE_PIOB, }, { .id = AT91SAM9263_ID_PIOCDE, - .offset = AT91_PIOC, - .clock = &pioCDE_clk, + .regbase = AT91SAM9263_BASE_PIOC, }, { .id = AT91SAM9263_ID_PIOCDE, - .offset = AT91_PIOD, - .clock = &pioCDE_clk, + .regbase = AT91SAM9263_BASE_PIOD, }, { .id = AT91SAM9263_ID_PIOCDE, - .offset = AT91_PIOE, - .clock = &pioCDE_clk, + .regbase = AT91SAM9263_BASE_PIOE, } }; -static void at91sam9263_poweroff(void) -{ - at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -} - - /* -------------------------------------------------------------------- * AT91SAM9263 processor initialization * -------------------------------------------------------------------- */ @@ -303,10 +298,17 @@ static void __init at91sam9263_map_io(void) at91_init_sram(1, AT91SAM9263_SRAM1_BASE, AT91SAM9263_SRAM1_SIZE); } +static void __init at91sam9263_ioremap_registers(void) +{ + at91_ioremap_shdwc(AT91SAM9263_BASE_SHDWC); + at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT); + at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0); + at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1); +} + static void __init at91sam9263_initialize(void) { at91_arch_reset = at91sam9_alt_reset; - pm_power_off = at91sam9263_poweroff; at91_extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1); /* Register GPIO subsystem */ @@ -358,6 +360,7 @@ static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91sam9263_soc = { .map_io = at91sam9263_map_io, .default_irq_priority = at91sam9263_default_irq_priority, + .ioremap_registers = at91sam9263_ioremap_registers, .register_clocks = at91sam9263_register_clocks, .init = at91sam9263_initialize, }; diff --git a/arch/arm/mach-at91/at91sam9263_devices.c b/arch/arm/mach-at91/at91sam9263_devices.c index ad017eb1f8df..7b46b2787022 100644 --- a/arch/arm/mach-at91/at91sam9263_devices.c +++ b/arch/arm/mach-at91/at91sam9263_devices.c @@ -70,7 +70,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) /* Enable VBus control for UHP ports */ for (i = 0; i < data->ports; i++) { - if (data->vbus_pin[i]) + if (gpio_is_valid(data->vbus_pin[i])) at91_set_gpio_output(data->vbus_pin[i], 0); } @@ -92,7 +92,7 @@ void __init at91_add_device_usbh(struct at91_usbh_data *data) {} * USB Device (Gadget) * -------------------------------------------------------------------- */ -#ifdef CONFIG_USB_GADGET_AT91 +#ifdef CONFIG_USB_AT91 static struct at91_udc_data udc_data; static struct resource udc_resources[] = { @@ -123,7 +123,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) if (!data) return; - if (data->vbus_pin) { + if (gpio_is_valid(data->vbus_pin)) { at91_set_gpio_input(data->vbus_pin, 0); at91_set_deglitch(data->vbus_pin, 1); } @@ -144,7 +144,7 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {} #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) static u64 eth_dmamask = DMA_BIT_MASK(32); -static struct at91_eth_data eth_data; +static struct macb_platform_data eth_data; static struct resource eth_resources[] = { [0] = { @@ -171,12 +171,12 @@ static struct platform_device at91sam9263_eth_device = { .num_resources = ARRAY_SIZE(eth_resources), }; -void __init at91_add_device_eth(struct at91_eth_data *data) +void __init at91_add_device_eth(struct macb_platform_data *data) { if (!data) return; - if (data->phy_irq_pin) { + if (gpio_is_valid(data->phy_irq_pin)) { at91_set_gpio_input(data->phy_irq_pin, 0); at91_set_deglitch(data->phy_irq_pin, 1); } @@ -208,7 +208,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data) platform_device_register(&at91sam9263_eth_device); } #else -void __init at91_add_device_eth(struct at91_eth_data *data) {} +void __init at91_add_device_eth(struct macb_platform_data *data) {} #endif @@ -276,13 +276,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) return; /* input/irq */ - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 1); at91_set_deglitch(data->det_pin, 1); } - if (data->wp_pin) + if (gpio_is_valid(data->wp_pin)) at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) at91_set_gpio_output(data->vcc_pin, 0); if (mmc_id == 0) { /* MCI0 */ @@ -430,17 +430,17 @@ void __init at91_add_device_cf(struct at91_cf_data *data) } at91_sys_write(AT91_MATRIX_EBI0CSA, ebi0_csa); - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 1); at91_set_deglitch(data->det_pin, 1); } - if (data->irq_pin) { + if (gpio_is_valid(data->irq_pin)) { at91_set_gpio_input(data->irq_pin, 1); at91_set_deglitch(data->irq_pin, 1); } - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) /* initially off */ at91_set_gpio_output(data->vcc_pin, 0); @@ -473,8 +473,8 @@ static struct resource nand_resources[] = { .flags = IORESOURCE_MEM, }, [1] = { - .start = AT91_BASE_SYS + AT91_ECC0, - .end = AT91_BASE_SYS + AT91_ECC0 + SZ_512 - 1, + .start = AT91SAM9263_BASE_ECC0, + .end = AT91SAM9263_BASE_ECC0 + SZ_512 - 1, .flags = IORESOURCE_MEM, } }; @@ -500,15 +500,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data) at91_sys_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA); /* enable pin */ - if (data->enable_pin) + if (gpio_is_valid(data->enable_pin)) at91_set_gpio_output(data->enable_pin, 1); /* ready/busy pin */ - if (data->rdy_pin) + if (gpio_is_valid(data->rdy_pin)) at91_set_gpio_input(data->rdy_pin, 1); /* card detect pin */ - if (data->det_pin) + if (gpio_is_valid(data->det_pin)) at91_set_gpio_input(data->det_pin, 1); nand_data = *data; @@ -749,7 +749,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) at91_set_A_periph(AT91_PIN_PB3, 0); /* AC97RX */ /* reset */ - if (data->reset_pin) + if (gpio_is_valid(data->reset_pin)) at91_set_gpio_output(data->reset_pin, 0); ac97_data = *data; @@ -956,8 +956,8 @@ static void __init at91_add_device_tc(void) { } static struct resource rtt0_resources[] = { { - .start = AT91_BASE_SYS + AT91_RTT0, - .end = AT91_BASE_SYS + AT91_RTT0 + SZ_16 - 1, + .start = AT91SAM9263_BASE_RTT0, + .end = AT91SAM9263_BASE_RTT0 + SZ_16 - 1, .flags = IORESOURCE_MEM, } }; @@ -971,8 +971,8 @@ static struct platform_device at91sam9263_rtt0_device = { static struct resource rtt1_resources[] = { { - .start = AT91_BASE_SYS + AT91_RTT1, - .end = AT91_BASE_SYS + AT91_RTT1 + SZ_16 - 1, + .start = AT91SAM9263_BASE_RTT1, + .end = AT91SAM9263_BASE_RTT1 + SZ_16 - 1, .flags = IORESOURCE_MEM, } }; @@ -996,10 +996,19 @@ static void __init at91_add_device_rtt(void) * -------------------------------------------------------------------- */ #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE) +static struct resource wdt_resources[] = { + { + .start = AT91SAM9263_BASE_WDT, + .end = AT91SAM9263_BASE_WDT + SZ_16 - 1, + .flags = IORESOURCE_MEM, + } +}; + static struct platform_device at91sam9263_wdt_device = { .name = "at91_wdt", .id = -1, - .num_resources = 0, + .resource = wdt_resources, + .num_resources = ARRAY_SIZE(wdt_resources), }; static void __init at91_add_device_watchdog(void) @@ -1196,8 +1205,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {} static struct resource dbgu_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DBGU, - .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .start = AT91SAM9263_BASE_DBGU, + .end = AT91SAM9263_BASE_DBGU + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { diff --git a/arch/arm/mach-at91/at91sam926x_time.c b/arch/arm/mach-at91/at91sam926x_time.c index 4ba85499fa97..d89ead740a99 100644 --- a/arch/arm/mach-at91/at91sam926x_time.c +++ b/arch/arm/mach-at91/at91sam926x_time.c @@ -25,7 +25,17 @@ static u32 pit_cycle; /* write-once */ static u32 pit_cnt; /* access only w/system irq blocked */ +static void __iomem *pit_base_addr __read_mostly; +static inline unsigned int pit_read(unsigned int reg_offset) +{ + return __raw_readl(pit_base_addr + reg_offset); +} + +static inline void pit_write(unsigned int reg_offset, unsigned long value) +{ + __raw_writel(value, pit_base_addr + reg_offset); +} /* * Clocksource: just a monotonic counter of MCK/16 cycles. @@ -39,7 +49,7 @@ static cycle_t read_pit_clk(struct clocksource *cs) raw_local_irq_save(flags); elapsed = pit_cnt; - t = at91_sys_read(AT91_PIT_PIIR); + t = pit_read(AT91_PIT_PIIR); raw_local_irq_restore(flags); elapsed += PIT_PICNT(t) * pit_cycle; @@ -64,8 +74,8 @@ pit_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev) switch (mode) { case CLOCK_EVT_MODE_PERIODIC: /* update clocksource counter */ - pit_cnt += pit_cycle * PIT_PICNT(at91_sys_read(AT91_PIT_PIVR)); - at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN + pit_cnt += pit_cycle * PIT_PICNT(pit_read(AT91_PIT_PIVR)); + pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN | AT91_PIT_PITIEN); break; case CLOCK_EVT_MODE_ONESHOT: @@ -74,7 +84,7 @@ pit_clkevt_mode(enum clock_event_mode mode, struct clock_event_device *dev) case CLOCK_EVT_MODE_SHUTDOWN: case CLOCK_EVT_MODE_UNUSED: /* disable irq, leaving the clocksource active */ - at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN); + pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN); break; case CLOCK_EVT_MODE_RESUME: break; @@ -103,11 +113,11 @@ static irqreturn_t at91sam926x_pit_interrupt(int irq, void *dev_id) /* The PIT interrupt may be disabled, and is shared */ if ((pit_clkevt.mode == CLOCK_EVT_MODE_PERIODIC) - && (at91_sys_read(AT91_PIT_SR) & AT91_PIT_PITS)) { + && (pit_read(AT91_PIT_SR) & AT91_PIT_PITS)) { unsigned nr_ticks; /* Get number of ticks performed before irq, and ack it */ - nr_ticks = PIT_PICNT(at91_sys_read(AT91_PIT_PIVR)); + nr_ticks = PIT_PICNT(pit_read(AT91_PIT_PIVR)); do { pit_cnt += pit_cycle; pit_clkevt.event_handler(&pit_clkevt); @@ -129,14 +139,14 @@ static struct irqaction at91sam926x_pit_irq = { static void at91sam926x_pit_reset(void) { /* Disable timer and irqs */ - at91_sys_write(AT91_PIT_MR, 0); + pit_write(AT91_PIT_MR, 0); /* Clear any pending interrupts, wait for PIT to stop counting */ - while (PIT_CPIV(at91_sys_read(AT91_PIT_PIVR)) != 0) + while (PIT_CPIV(pit_read(AT91_PIT_PIVR)) != 0) cpu_relax(); /* Start PIT but don't enable IRQ */ - at91_sys_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN); + pit_write(AT91_PIT_MR, (pit_cycle - 1) | AT91_PIT_PITEN); } /* @@ -178,7 +188,15 @@ static void __init at91sam926x_pit_init(void) static void at91sam926x_pit_suspend(void) { /* Disable timer */ - at91_sys_write(AT91_PIT_MR, 0); + pit_write(AT91_PIT_MR, 0); +} + +void __init at91sam926x_ioremap_pit(u32 addr) +{ + pit_base_addr = ioremap(addr, 16); + + if (!pit_base_addr) + panic("Impossible to ioremap PIT\n"); } struct sys_timer at91sam926x_timer = { diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c index 318b0407ea04..f61eb64e6b39 100644 --- a/arch/arm/mach-at91/at91sam9g45.c +++ b/arch/arm/mach-at91/at91sam9g45.c @@ -11,7 +11,6 @@ */ #include <linux/module.h> -#include <linux/pm.h> #include <linux/dma-mapping.h> #include <asm/irq.h> @@ -20,12 +19,12 @@ #include <mach/at91sam9g45.h> #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> -#include <mach/at91_shdwc.h> #include <mach/cpu.h> #include "soc.h" #include "generic.h" #include "clock.h" +#include "sam9_smc.h" /* -------------------------------------------------------------------- * Clocks @@ -150,7 +149,7 @@ static struct clk ac97_clk = { .type = CLK_TYPE_PERIPHERAL, }; static struct clk macb_clk = { - .name = "macb_clk", + .name = "pclk", .pmc_mask = 1 << AT91SAM9G45_ID_EMAC, .type = CLK_TYPE_PERIPHERAL, }; @@ -209,6 +208,8 @@ static struct clk *periph_clocks[] __initdata = { }; static struct clk_lookup periph_clocks_lookups[] = { + /* One additional fake clock for macb_hclk */ + CLKDEV_CON_ID("hclk", &macb_clk), /* One additional fake clock for ohci */ CLKDEV_CON_ID("ohci_clk", &uhphs_clk), CLKDEV_CON_DEV_ID("ehci_clk", "atmel-ehci", &uhphs_clk), @@ -231,6 +232,11 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("usart", "fff98000.serial", &usart3_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk), + CLKDEV_CON_ID("pioA", &pioA_clk), + CLKDEV_CON_ID("pioB", &pioB_clk), + CLKDEV_CON_ID("pioC", &pioC_clk), + CLKDEV_CON_ID("pioD", &pioDE_clk), + CLKDEV_CON_ID("pioE", &pioDE_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -293,27 +299,22 @@ void __init at91sam9g45_set_console_clock(int id) * GPIO * -------------------------------------------------------------------- */ -static struct at91_gpio_bank at91sam9g45_gpio[] = { +static struct at91_gpio_bank at91sam9g45_gpio[] __initdata = { { .id = AT91SAM9G45_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, + .regbase = AT91SAM9G45_BASE_PIOA, }, { .id = AT91SAM9G45_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, + .regbase = AT91SAM9G45_BASE_PIOB, }, { .id = AT91SAM9G45_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, + .regbase = AT91SAM9G45_BASE_PIOC, }, { .id = AT91SAM9G45_ID_PIODE, - .offset = AT91_PIOD, - .clock = &pioDE_clk, + .regbase = AT91SAM9G45_BASE_PIOD, }, { .id = AT91SAM9G45_ID_PIODE, - .offset = AT91_PIOE, - .clock = &pioDE_clk, + .regbase = AT91SAM9G45_BASE_PIOE, } }; @@ -322,12 +323,6 @@ static void at91sam9g45_reset(void) at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_PROCRST | AT91_RSTC_PERRST); } -static void at91sam9g45_poweroff(void) -{ - at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -} - - /* -------------------------------------------------------------------- * AT91SAM9G45 processor initialization * -------------------------------------------------------------------- */ @@ -338,10 +333,16 @@ static void __init at91sam9g45_map_io(void) init_consistent_dma_size(SZ_4M); } +static void __init at91sam9g45_ioremap_registers(void) +{ + at91_ioremap_shdwc(AT91SAM9G45_BASE_SHDWC); + at91sam926x_ioremap_pit(AT91SAM9G45_BASE_PIT); + at91sam9_ioremap_smc(0, AT91SAM9G45_BASE_SMC); +} + static void __init at91sam9g45_initialize(void) { at91_arch_reset = at91sam9g45_reset; - pm_power_off = at91sam9g45_poweroff; at91_extern_irq = (1 << AT91SAM9G45_ID_IRQ0); /* Register GPIO subsystem */ @@ -393,6 +394,7 @@ static unsigned int at91sam9g45_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91sam9g45_soc = { .map_io = at91sam9g45_map_io, .default_irq_priority = at91sam9g45_default_irq_priority, + .ioremap_registers = at91sam9g45_ioremap_registers, .register_clocks = at91sam9g45_register_clocks, .init = at91sam9g45_initialize, }; diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c index 09a16d6bd5cd..b7582dd10dc3 100644 --- a/arch/arm/mach-at91/at91sam9g45_devices.c +++ b/arch/arm/mach-at91/at91sam9g45_devices.c @@ -44,8 +44,8 @@ static struct at_dma_platform_data atdma_pdata = { static struct resource hdmac_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DMA, - .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1, + .start = AT91SAM9G45_BASE_DMA, + .end = AT91SAM9G45_BASE_DMA + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { @@ -120,7 +120,7 @@ void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data) /* Enable VBus control for UHP ports */ for (i = 0; i < data->ports; i++) { - if (data->vbus_pin[i]) + if (gpio_is_valid(data->vbus_pin[i])) at91_set_gpio_output(data->vbus_pin[i], 0); } @@ -181,7 +181,7 @@ void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data) /* Enable VBus control for UHP ports */ for (i = 0; i < data->ports; i++) { - if (data->vbus_pin[i]) + if (gpio_is_valid(data->vbus_pin[i])) at91_set_gpio_output(data->vbus_pin[i], 0); } @@ -263,7 +263,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep); memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep)); - if (data && data->vbus_pin > 0) { + if (data && gpio_is_valid(data->vbus_pin)) { at91_set_gpio_input(data->vbus_pin, 0); at91_set_deglitch(data->vbus_pin, 1); usba_udc_data.pdata.vbus_pin = data->vbus_pin; @@ -284,7 +284,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) {} #if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE) static u64 eth_dmamask = DMA_BIT_MASK(32); -static struct at91_eth_data eth_data; +static struct macb_platform_data eth_data; static struct resource eth_resources[] = { [0] = { @@ -311,12 +311,12 @@ static struct platform_device at91sam9g45_eth_device = { .num_resources = ARRAY_SIZE(eth_resources), }; -void __init at91_add_device_eth(struct at91_eth_data *data) +void __init at91_add_device_eth(struct macb_platform_data *data) { if (!data) return; - if (data->phy_irq_pin) { + if (gpio_is_valid(data->phy_irq_pin)) { at91_set_gpio_input(data->phy_irq_pin, 0); at91_set_deglitch(data->phy_irq_pin, 1); } @@ -348,7 +348,7 @@ void __init at91_add_device_eth(struct at91_eth_data *data) platform_device_register(&at91sam9g45_eth_device); } #else -void __init at91_add_device_eth(struct at91_eth_data *data) {} +void __init at91_add_device_eth(struct macb_platform_data *data) {} #endif @@ -449,11 +449,11 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) /* input/irq */ - if (data->slot[0].detect_pin) { + if (gpio_is_valid(data->slot[0].detect_pin)) { at91_set_gpio_input(data->slot[0].detect_pin, 1); at91_set_deglitch(data->slot[0].detect_pin, 1); } - if (data->slot[0].wp_pin) + if (gpio_is_valid(data->slot[0].wp_pin)) at91_set_gpio_input(data->slot[0].wp_pin, 1); if (mmc_id == 0) { /* MCI0 */ @@ -529,8 +529,8 @@ static struct resource nand_resources[] = { .flags = IORESOURCE_MEM, }, [1] = { - .start = AT91_BASE_SYS + AT91_ECC, - .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1, + .start = AT91SAM9G45_BASE_ECC, + .end = AT91SAM9G45_BASE_ECC + SZ_512 - 1, .flags = IORESOURCE_MEM, } }; @@ -556,15 +556,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA); /* enable pin */ - if (data->enable_pin) + if (gpio_is_valid(data->enable_pin)) at91_set_gpio_output(data->enable_pin, 1); /* ready/busy pin */ - if (data->rdy_pin) + if (gpio_is_valid(data->rdy_pin)) at91_set_gpio_input(data->rdy_pin, 1); /* card detect pin */ - if (data->det_pin) + if (gpio_is_valid(data->det_pin)) at91_set_gpio_input(data->det_pin, 1); nand_data = *data; @@ -859,7 +859,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) at91_set_A_periph(AT91_PIN_PD6, 0); /* AC97RX */ /* reset */ - if (data->reset_pin) + if (gpio_is_valid(data->reset_pin)) at91_set_gpio_output(data->reset_pin, 0); ac97_data = *data; @@ -1009,10 +1009,24 @@ static void __init at91_add_device_tc(void) { } * -------------------------------------------------------------------- */ #if defined(CONFIG_RTC_DRV_AT91RM9200) || defined(CONFIG_RTC_DRV_AT91RM9200_MODULE) +static struct resource rtc_resources[] = { + [0] = { + .start = AT91SAM9G45_BASE_RTC, + .end = AT91SAM9G45_BASE_RTC + SZ_256 - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = AT91_ID_SYS, + .end = AT91_ID_SYS, + .flags = IORESOURCE_IRQ, + }, +}; + static struct platform_device at91sam9g45_rtc_device = { .name = "at91_rtc", .id = -1, - .num_resources = 0, + .resource = rtc_resources, + .num_resources = ARRAY_SIZE(rtc_resources), }; static void __init at91_add_device_rtc(void) @@ -1081,8 +1095,8 @@ void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data) {} static struct resource rtt_resources[] = { { - .start = AT91_BASE_SYS + AT91_RTT, - .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1, + .start = AT91SAM9G45_BASE_RTT, + .end = AT91SAM9G45_BASE_RTT + SZ_16 - 1, .flags = IORESOURCE_MEM, } }; @@ -1133,10 +1147,19 @@ static void __init at91_add_device_trng(void) {} * -------------------------------------------------------------------- */ #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE) +static struct resource wdt_resources[] = { + { + .start = AT91SAM9G45_BASE_WDT, + .end = AT91SAM9G45_BASE_WDT + SZ_16 - 1, + .flags = IORESOURCE_MEM, + } +}; + static struct platform_device at91sam9g45_wdt_device = { .name = "at91_wdt", .id = -1, - .num_resources = 0, + .resource = wdt_resources, + .num_resources = ARRAY_SIZE(wdt_resources), }; static void __init at91_add_device_watchdog(void) @@ -1332,8 +1355,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {} #if defined(CONFIG_SERIAL_ATMEL) static struct resource dbgu_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DBGU, - .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .start = AT91SAM9G45_BASE_DBGU, + .end = AT91SAM9G45_BASE_DBGU + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { diff --git a/arch/arm/mach-at91/at91sam9rl.c b/arch/arm/mach-at91/at91sam9rl.c index a238105d2c11..96247f68b9d2 100644 --- a/arch/arm/mach-at91/at91sam9rl.c +++ b/arch/arm/mach-at91/at91sam9rl.c @@ -10,7 +10,6 @@ */ #include <linux/module.h> -#include <linux/pm.h> #include <asm/irq.h> #include <asm/mach/arch.h> @@ -20,11 +19,11 @@ #include <mach/at91sam9rl.h> #include <mach/at91_pmc.h> #include <mach/at91_rstc.h> -#include <mach/at91_shdwc.h> #include "soc.h" #include "generic.h" #include "clock.h" +#include "sam9_smc.h" /* -------------------------------------------------------------------- * Clocks @@ -184,6 +183,10 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("t2_clk", "atmel_tcb.0", &tc2_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk), CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk), + CLKDEV_CON_ID("pioA", &pioA_clk), + CLKDEV_CON_ID("pioB", &pioB_clk), + CLKDEV_CON_ID("pioC", &pioC_clk), + CLKDEV_CON_ID("pioD", &pioD_clk), }; static struct clk_lookup usart_clocks_lookups[] = { @@ -243,32 +246,22 @@ void __init at91sam9rl_set_console_clock(int id) * GPIO * -------------------------------------------------------------------- */ -static struct at91_gpio_bank at91sam9rl_gpio[] = { +static struct at91_gpio_bank at91sam9rl_gpio[] __initdata = { { .id = AT91SAM9RL_ID_PIOA, - .offset = AT91_PIOA, - .clock = &pioA_clk, + .regbase = AT91SAM9RL_BASE_PIOA, }, { .id = AT91SAM9RL_ID_PIOB, - .offset = AT91_PIOB, - .clock = &pioB_clk, + .regbase = AT91SAM9RL_BASE_PIOB, }, { .id = AT91SAM9RL_ID_PIOC, - .offset = AT91_PIOC, - .clock = &pioC_clk, + .regbase = AT91SAM9RL_BASE_PIOC, }, { .id = AT91SAM9RL_ID_PIOD, - .offset = AT91_PIOD, - .clock = &pioD_clk, + .regbase = AT91SAM9RL_BASE_PIOD, } }; -static void at91sam9rl_poweroff(void) -{ - at91_sys_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); -} - - /* -------------------------------------------------------------------- * AT91SAM9RL processor initialization * -------------------------------------------------------------------- */ @@ -290,10 +283,16 @@ static void __init at91sam9rl_map_io(void) at91_init_sram(0, AT91SAM9RL_SRAM_BASE, sram_size); } +static void __init at91sam9rl_ioremap_registers(void) +{ + at91_ioremap_shdwc(AT91SAM9RL_BASE_SHDWC); + at91sam926x_ioremap_pit(AT91SAM9RL_BASE_PIT); + at91sam9_ioremap_smc(0, AT91SAM9RL_BASE_SMC); +} + static void __init at91sam9rl_initialize(void) { at91_arch_reset = at91sam9_alt_reset; - pm_power_off = at91sam9rl_poweroff; at91_extern_irq = (1 << AT91SAM9RL_ID_IRQ0); /* Register GPIO subsystem */ @@ -345,6 +344,7 @@ static unsigned int at91sam9rl_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91sam9rl_soc = { .map_io = at91sam9rl_map_io, .default_irq_priority = at91sam9rl_default_irq_priority, + .ioremap_registers = at91sam9rl_ioremap_registers, .register_clocks = at91sam9rl_register_clocks, .init = at91sam9rl_initialize, }; diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index 628eb566d60c..61908dce9784 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -39,8 +39,8 @@ static struct at_dma_platform_data atdma_pdata = { static struct resource hdmac_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DMA, - .end = AT91_BASE_SYS + AT91_DMA + SZ_512 - 1, + .start = AT91SAM9RL_BASE_DMA, + .end = AT91SAM9RL_BASE_DMA + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [2] = { @@ -147,7 +147,7 @@ void __init at91_add_device_usba(struct usba_platform_data *data) usba_udc_data.pdata.num_ep = ARRAY_SIZE(usba_udc_ep); memcpy(usba_udc_data.ep, usba_udc_ep, sizeof(usba_udc_ep)); - if (data && data->vbus_pin > 0) { + if (data && gpio_is_valid(data->vbus_pin)) { at91_set_gpio_input(data->vbus_pin, 0); at91_set_deglitch(data->vbus_pin, 1); usba_udc_data.pdata.vbus_pin = data->vbus_pin; @@ -201,13 +201,13 @@ void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) return; /* input/irq */ - if (data->det_pin) { + if (gpio_is_valid(data->det_pin)) { at91_set_gpio_input(data->det_pin, 1); at91_set_deglitch(data->det_pin, 1); } - if (data->wp_pin) + if (gpio_is_valid(data->wp_pin)) at91_set_gpio_input(data->wp_pin, 1); - if (data->vcc_pin) + if (gpio_is_valid(data->vcc_pin)) at91_set_gpio_output(data->vcc_pin, 0); /* CLK */ @@ -248,8 +248,8 @@ static struct resource nand_resources[] = { .flags = IORESOURCE_MEM, }, [1] = { - .start = AT91_BASE_SYS + AT91_ECC, - .end = AT91_BASE_SYS + AT91_ECC + SZ_512 - 1, + .start = AT91SAM9RL_BASE_ECC, + .end = AT91SAM9RL_BASE_ECC + SZ_512 - 1, .flags = IORESOURCE_MEM, } }; @@ -275,15 +275,15 @@ void __init at91_add_device_nand(struct atmel_nand_data *data) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA); /* enable pin */ - if (data->enable_pin) + if (gpio_is_valid(data->enable_pin)) at91_set_gpio_output(data->enable_pin, 1); /* ready/busy pin */ - if (data->rdy_pin) + if (gpio_is_valid(data->rdy_pin)) at91_set_gpio_input(data->rdy_pin, 1); /* card detect pin */ - if (data->det_pin) + if (gpio_is_valid(data->det_pin)) at91_set_gpio_input(data->det_pin, 1); at91_set_A_periph(AT91_PIN_PB4, 0); /* NANDOE */ @@ -483,7 +483,7 @@ void __init at91_add_device_ac97(struct ac97c_platform_data *data) at91_set_A_periph(AT91_PIN_PD4, 0); /* AC97RX */ /* reset */ - if (data->reset_pin) + if (gpio_is_valid(data->reset_pin)) at91_set_gpio_output(data->reset_pin, 0); ac97_data = *data; @@ -685,8 +685,8 @@ static void __init at91_add_device_rtc(void) {} static struct resource rtt_resources[] = { { - .start = AT91_BASE_SYS + AT91_RTT, - .end = AT91_BASE_SYS + AT91_RTT + SZ_16 - 1, + .start = AT91SAM9RL_BASE_RTT, + .end = AT91SAM9RL_BASE_RTT + SZ_16 - 1, .flags = IORESOURCE_MEM, } }; @@ -709,10 +709,19 @@ static void __init at91_add_device_rtt(void) * -------------------------------------------------------------------- */ #if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE) +static struct resource wdt_resources[] = { + { + .start = AT91SAM9RL_BASE_WDT, + .end = AT91SAM9RL_BASE_WDT + SZ_16 - 1, + .flags = IORESOURCE_MEM, + } +}; + static struct platform_device at91sam9rl_wdt_device = { .name = "at91_wdt", .id = -1, - .num_resources = 0, + .resource = wdt_resources, + .num_resources = ARRAY_SIZE(wdt_resources), }; static void __init at91_add_device_watchdog(void) @@ -908,8 +917,8 @@ void __init at91_add_device_ssc(unsigned id, unsigned pins) {} #if defined(CONFIG_SERIAL_ATMEL) static struct resource dbgu_resources[] = { [0] = { - .start = AT91_BASE_SYS + AT91_DBGU, - .end = AT91_BASE_SYS + AT91_DBGU + SZ_512 - 1, + .start = AT91SAM9RL_BASE_DBGU, + .end = AT91SAM9RL_BASE_DBGU + SZ_512 - 1, .flags = IORESOURCE_MEM, }, [1] = { diff --git a/arch/arm/mach-at91/board-1arm.c b/arch/arm/mach-at91/board-1arm.c index 367d5cd5e362..2628384aaae1 100644 --- a/arch/arm/mach-at91/board-1arm.c +++ b/arch/arm/mach-at91/board-1arm.c @@ -63,13 +63,15 @@ static void __init onearm_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata onearm_eth_data = { +static struct macb_platform_data __initdata onearm_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; static struct at91_usbh_data __initdata onearm_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata onearm_udc_data = { diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index 4282d96dffa8..3bb40694b02d 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -75,6 +75,8 @@ static void __init afeb9260_init_early(void) */ static struct at91_usbh_data __initdata afeb9260_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = { */ static struct at91_udc_data __initdata afeb9260_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -103,7 +105,7 @@ static struct spi_board_info afeb9260_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata afeb9260_macb_data = { +static struct macb_platform_data __initdata afeb9260_macb_data = { .phy_irq_pin = AT91_PIN_PA9, .is_rmii = 0, }; @@ -138,6 +140,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = { .bus_width_16 = 0, .parts = afeb9260_nand_partition, .num_parts = ARRAY_SIZE(afeb9260_nand_partition), + .det_pin = -EINVAL, }; @@ -149,6 +152,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = { .wp_pin = AT91_PIN_PC4, .slot_b = 1, .wire4 = 1, + .vcc_pin = -EINVAL, }; @@ -169,6 +173,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = { static struct at91_cf_data afeb9260_cf_data = { .chipselect = 4, .irq_pin = AT91_PIN_PA6, + .det_pin = -EINVAL, + .vcc_pin = -EINVAL, .rst_pin = AT91_PIN_PA7, .flags = AT91_CF_TRUE_IDE, }; diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c index f90cfb32bad2..8510e9e54988 100644 --- a/arch/arm/mach-at91/board-cam60.c +++ b/arch/arm/mach-at91/board-cam60.c @@ -62,6 +62,8 @@ static void __init cam60_init_early(void) */ static struct at91_usbh_data __initdata cam60_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; @@ -115,7 +117,7 @@ static struct spi_board_info cam60_spi_devices[] __initdata = { /* * MACB Ethernet device */ -static struct __initdata at91_eth_data cam60_macb_data = { +static struct __initdata macb_platform_data cam60_macb_data = { .phy_irq_pin = AT91_PIN_PB5, .is_rmii = 0, }; @@ -135,7 +137,7 @@ static struct mtd_partition __initdata cam60_nand_partition[] = { static struct atmel_nand_data __initdata cam60_nand_data = { .ale = 21, .cle = 22, - // .det_pin = ... not there + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PA9, .enable_pin = AT91_PIN_PA7, .parts = cam60_nand_partition, @@ -163,7 +165,7 @@ static struct sam9_smc_config __initdata cam60_nand_smc_config = { static void __init cam60_add_device_nand(void) { /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &cam60_nand_smc_config); + sam9_smc_configure(0, 3, &cam60_nand_smc_config); at91_add_device_nand(&cam60_nand_data); } diff --git a/arch/arm/mach-at91/board-cap9adk.c b/arch/arm/mach-at91/board-cap9adk.c index 5dffd3be62d2..ac3de4f7c31d 100644 --- a/arch/arm/mach-at91/board-cap9adk.c +++ b/arch/arm/mach-at91/board-cap9adk.c @@ -70,6 +70,8 @@ static void __init cap9adk_init_early(void) */ static struct at91_usbh_data __initdata cap9adk_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -144,16 +146,17 @@ static struct spi_board_info cap9adk_spi_devices[] = { */ static struct at91_mmc_data __initdata cap9adk_mmc_data = { .wire4 = 1, -// .det_pin = ... not connected -// .wp_pin = ... not connected -// .vcc_pin = ... not connected + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; /* * MACB Ethernet device */ -static struct at91_eth_data __initdata cap9adk_macb_data = { +static struct macb_platform_data __initdata cap9adk_macb_data = { + .phy_irq_pin = -EINVAL, .is_rmii = 1, }; @@ -172,8 +175,8 @@ static struct mtd_partition __initdata cap9adk_nand_partitions[] = { static struct atmel_nand_data __initdata cap9adk_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected -// .rdy_pin = ... not connected + .det_pin = -EINVAL, + .rdy_pin = -EINVAL, .enable_pin = AT91_PIN_PD15, .parts = cap9adk_nand_partitions, .num_parts = ARRAY_SIZE(cap9adk_nand_partitions), @@ -212,7 +215,7 @@ static void __init cap9adk_add_device_nand(void) cap9adk_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &cap9adk_nand_smc_config); + sam9_smc_configure(0, 3, &cap9adk_nand_smc_config); at91_add_device_nand(&cap9adk_nand_data); } @@ -282,7 +285,7 @@ static __init void cap9adk_add_device_nor(void) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_VDDIOMSEL_3_3V); /* configure chip-select 0 (NOR) */ - sam9_smc_configure(0, &cap9adk_nor_smc_config); + sam9_smc_configure(0, 0, &cap9adk_nor_smc_config); platform_device_register(&cap9adk_nor_flash); } @@ -351,7 +354,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data; * AC97 */ static struct ac97c_platform_data cap9adk_ac97_data = { -// .reset_pin = ... not connected + .reset_pin = -EINVAL, }; diff --git a/arch/arm/mach-at91/board-carmeva.c b/arch/arm/mach-at91/board-carmeva.c index 774c87fcbd5b..59d9cf997537 100644 --- a/arch/arm/mach-at91/board-carmeva.c +++ b/arch/arm/mach-at91/board-carmeva.c @@ -57,13 +57,15 @@ static void __init carmeva_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata carmeva_eth_data = { +static struct macb_platform_data __initdata carmeva_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; static struct at91_usbh_data __initdata carmeva_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata carmeva_udc_data = { @@ -75,8 +77,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = { // static struct at91_cf_data __initdata carmeva_cf_data = { // .det_pin = AT91_PIN_PB0, // .rst_pin = AT91_PIN_PC5, - // .irq_pin = ... not connected - // .vcc_pin = ... always powered + // .irq_pin = -EINVAL, + // .vcc_pin = -EINVAL, // }; static struct at91_mmc_data __initdata carmeva_mmc_data = { @@ -84,6 +86,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PB10, .wp_pin = AT91_PIN_PC14, + .vcc_pin = -EINVAL, }; static struct spi_board_info carmeva_spi_devices[] = { diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index fc885a4ce243..9ab3d1ea326d 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -86,6 +86,8 @@ static void __init cpu9krea_init_early(void) */ static struct at91_usbh_data __initdata cpu9krea_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -93,13 +95,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = { */ static struct at91_udc_data __initdata cpu9krea_udc_data = { .vbus_pin = AT91_PIN_PC8, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; /* * MACB Ethernet device */ -static struct at91_eth_data __initdata cpu9krea_macb_data = { +static struct macb_platform_data __initdata cpu9krea_macb_data = { + .phy_irq_pin = -EINVAL, .is_rmii = 1, }; @@ -112,6 +115,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = { .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .bus_width_16 = 0, + .det_pin = -EINVAL, }; #ifdef CONFIG_MACH_CPU9260 @@ -156,7 +160,7 @@ static struct sam9_smc_config __initdata cpu9krea_nand_smc_config = { static void __init cpu9krea_add_device_nand(void) { - sam9_smc_configure(3, &cpu9krea_nand_smc_config); + sam9_smc_configure(0, 3, &cpu9krea_nand_smc_config); at91_add_device_nand(&cpu9krea_nand_data); } @@ -238,7 +242,7 @@ static __init void cpu9krea_add_device_nor(void) at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_VDDIOMSEL_3_3V); /* configure chip-select 0 (NOR) */ - sam9_smc_configure(0, &cpu9krea_nor_smc_config); + sam9_smc_configure(0, 0, &cpu9krea_nor_smc_config); platform_device_register(&cpu9krea_nor_flash); } @@ -337,6 +341,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = { .slot_b = 0, .wire4 = 1, .det_pin = AT91_PIN_PA29, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; static void __init cpu9krea_board_init(void) diff --git a/arch/arm/mach-at91/board-cpuat91.c b/arch/arm/mach-at91/board-cpuat91.c index d35e65b08ccd..368e1427ad99 100644 --- a/arch/arm/mach-at91/board-cpuat91.c +++ b/arch/arm/mach-at91/board-cpuat91.c @@ -82,12 +82,15 @@ static void __init cpuat91_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata cpuat91_eth_data = { +static struct macb_platform_data __initdata cpuat91_eth_data = { + .phy_irq_pin = -EINVAL, .is_rmii = 1, }; static struct at91_usbh_data __initdata cpuat91_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata cpuat91_udc_data = { @@ -98,6 +101,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = { static struct at91_mmc_data __initdata cpuat91_mmc_data = { .det_pin = AT91_PIN_PC2, .wire4 = 1, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; static struct physmap_flash_data cpuat91_flash_data = { diff --git a/arch/arm/mach-at91/board-csb337.c b/arch/arm/mach-at91/board-csb337.c index c3936665e645..1a1547b1ce4e 100644 --- a/arch/arm/mach-at91/board-csb337.c +++ b/arch/arm/mach-at91/board-csb337.c @@ -58,18 +58,20 @@ static void __init csb337_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata csb337_eth_data = { +static struct macb_platform_data __initdata csb337_eth_data = { .phy_irq_pin = AT91_PIN_PC2, .is_rmii = 0, }; static struct at91_usbh_data __initdata csb337_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata csb337_udc_data = { - // this has no VBUS sensing pin .pullup_pin = AT91_PIN_PA24, + .vbus_pin = -EINVAL, }; static struct i2c_board_info __initdata csb337_i2c_devices[] = { @@ -98,6 +100,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = { .slot_b = 0, .wire4 = 1, .wp_pin = AT91_PIN_PD6, + .vcc_pin = -EINVAL, }; static struct spi_board_info csb337_spi_devices[] = { diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c index 586100e2acbb..f650bf39455d 100644 --- a/arch/arm/mach-at91/board-csb637.c +++ b/arch/arm/mach-at91/board-csb637.c @@ -52,13 +52,15 @@ static void __init csb637_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata csb637_eth_data = { +static struct macb_platform_data __initdata csb637_eth_data = { .phy_irq_pin = AT91_PIN_PC0, .is_rmii = 0, }; static struct at91_usbh_data __initdata csb637_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata csb637_udc_data = { diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c index 0b7d32778210..bb6b434ec0c1 100644 --- a/arch/arm/mach-at91/board-dt.c +++ b/arch/arm/mach-at91/board-dt.c @@ -50,6 +50,7 @@ static void __init ek_init_early(void) static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC8, .enable_pin = AT91_PIN_PC14, }; @@ -82,7 +83,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } diff --git a/arch/arm/mach-at91/board-eb9200.c b/arch/arm/mach-at91/board-eb9200.c index 45db7a3dbef0..d302ca3eeb64 100644 --- a/arch/arm/mach-at91/board-eb9200.c +++ b/arch/arm/mach-at91/board-eb9200.c @@ -60,13 +60,15 @@ static void __init eb9200_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata eb9200_eth_data = { +static struct macb_platform_data __initdata eb9200_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; static struct at91_usbh_data __initdata eb9200_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata eb9200_udc_data = { @@ -75,15 +77,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = { }; static struct at91_cf_data __initdata eb9200_cf_data = { + .irq_pin = -EINVAL, .det_pin = AT91_PIN_PB0, + .vcc_pin = -EINVAL, .rst_pin = AT91_PIN_PC5, - // .irq_pin = ... not connected - // .vcc_pin = ... always powered }; static struct at91_mmc_data __initdata eb9200_mmc_data = { .slot_b = 0, .wire4 = 1, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; static struct i2c_board_info __initdata eb9200_i2c_devices[] = { diff --git a/arch/arm/mach-at91/board-ecbat91.c b/arch/arm/mach-at91/board-ecbat91.c index 2f9c16d29212..69966ce4d776 100644 --- a/arch/arm/mach-at91/board-ecbat91.c +++ b/arch/arm/mach-at91/board-ecbat91.c @@ -64,18 +64,23 @@ static void __init ecb_at91init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata ecb_at91eth_data = { +static struct macb_platform_data __initdata ecb_at91eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 0, }; static struct at91_usbh_data __initdata ecb_at91usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_mmc_data __initdata ecb_at91mmc_data = { .slot_b = 0, .wire4 = 1, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; diff --git a/arch/arm/mach-at91/board-eco920.c b/arch/arm/mach-at91/board-eco920.c index 8252c722607b..07ef35b0ec2c 100644 --- a/arch/arm/mach-at91/board-eco920.c +++ b/arch/arm/mach-at91/board-eco920.c @@ -47,13 +47,15 @@ static void __init eco920_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata eco920_eth_data = { +static struct macb_platform_data __initdata eco920_eth_data = { .phy_irq_pin = AT91_PIN_PC2, .is_rmii = 1, }; static struct at91_usbh_data __initdata eco920_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata eco920_udc_data = { @@ -64,6 +66,9 @@ static struct at91_udc_data __initdata eco920_udc_data = { static struct at91_mmc_data __initdata eco920_mmc_data = { .slot_b = 0, .wire4 = 0, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; static struct physmap_flash_data eco920_flash_data = { diff --git a/arch/arm/mach-at91/board-flexibity.c b/arch/arm/mach-at91/board-flexibity.c index 4c3f65d9c59b..eec02cd57ced 100644 --- a/arch/arm/mach-at91/board-flexibity.c +++ b/arch/arm/mach-at91/board-flexibity.c @@ -52,12 +52,14 @@ static void __init flexibity_init_early(void) /* USB Host port */ static struct at91_usbh_data __initdata flexibity_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* USB Device port */ static struct at91_udc_data __initdata flexibity_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; /* SPI devices */ @@ -76,6 +78,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PC9, .wp_pin = AT91_PIN_PC4, + .vcc_pin = -EINVAL, }; /* LEDs */ diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c index f27d1a780cfa..caf017f0f4ee 100644 --- a/arch/arm/mach-at91/board-foxg20.c +++ b/arch/arm/mach-at91/board-foxg20.c @@ -106,6 +106,8 @@ static void __init foxg20_init_early(void) */ static struct at91_usbh_data __initdata foxg20_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -113,7 +115,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = { */ static struct at91_udc_data __initdata foxg20_udc_data = { .vbus_pin = AT91_PIN_PC6, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -135,7 +137,7 @@ static struct spi_board_info foxg20_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata foxg20_macb_data = { +static struct macb_platform_data __initdata foxg20_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 1, }; @@ -147,6 +149,9 @@ static struct at91_eth_data __initdata foxg20_macb_data = { static struct at91_mmc_data __initdata foxg20_mmc_data = { .slot_b = 1, .wire4 = 1, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; diff --git a/arch/arm/mach-at91/board-gsia18s.c b/arch/arm/mach-at91/board-gsia18s.c index 2e95949737e6..230e71969fb7 100644 --- a/arch/arm/mach-at91/board-gsia18s.c +++ b/arch/arm/mach-at91/board-gsia18s.c @@ -80,6 +80,8 @@ static void __init gsia18s_init_early(void) */ static struct at91_usbh_data __initdata usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -87,13 +89,13 @@ static struct at91_usbh_data __initdata usbh_data = { */ static struct at91_udc_data __initdata udc_data = { .vbus_pin = AT91_PIN_PA22, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; /* * MACB Ethernet device */ -static struct at91_eth_data __initdata macb_data = { +static struct macb_platform_data __initdata macb_data = { .phy_irq_pin = AT91_PIN_PA28, .is_rmii = 1, }; @@ -530,6 +532,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = { static struct at91_cf_data __initdata gsia18s_cf1_data = { .irq_pin = AT91_PIN_PA27, .det_pin = AT91_PIN_PB30, + .vcc_pin = -EINVAL, .rst_pin = AT91_PIN_PB31, .chipselect = 5, .flags = AT91_CF_TRUE_IDE, diff --git a/arch/arm/mach-at91/board-kafa.c b/arch/arm/mach-at91/board-kafa.c index 3bae73e63633..efde1b2327c8 100644 --- a/arch/arm/mach-at91/board-kafa.c +++ b/arch/arm/mach-at91/board-kafa.c @@ -61,13 +61,15 @@ static void __init kafa_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata kafa_eth_data = { +static struct macb_platform_data __initdata kafa_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 0, }; static struct at91_usbh_data __initdata kafa_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata kafa_udc_data = { diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index e61351ffad50..d75a4a2ad9c2 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -69,13 +69,15 @@ static void __init kb9202_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata kb9202_eth_data = { +static struct macb_platform_data __initdata kb9202_eth_data = { .phy_irq_pin = AT91_PIN_PB29, .is_rmii = 0, }; static struct at91_usbh_data __initdata kb9202_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata kb9202_udc_data = { @@ -87,6 +89,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = { .det_pin = AT91_PIN_PB2, .slot_b = 0, .wire4 = 1, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; static struct mtd_partition __initdata kb9202_nand_partition[] = { @@ -100,7 +104,7 @@ static struct mtd_partition __initdata kb9202_nand_partition[] = { static struct atmel_nand_data __initdata kb9202_nand_data = { .ale = 22, .cle = 21, - // .det_pin = ... not there + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC29, .enable_pin = AT91_PIN_PC28, .parts = kb9202_nand_partition, diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index ef816c17dc61..3f8617c0e04e 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -72,6 +72,7 @@ static void __init neocore926_init_early(void) static struct at91_usbh_data __initdata neocore926_usbh_data = { .ports = 2, .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 }, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = { */ static struct at91_udc_data __initdata neocore926_udc_data = { .vbus_pin = AT91_PIN_PA25, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -149,13 +150,14 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, + .vcc_pin = -EINVAL, }; /* * MACB Ethernet device */ -static struct at91_eth_data __initdata neocore926_macb_data = { +static struct macb_platform_data __initdata neocore926_macb_data = { .phy_irq_pin = AT91_PIN_PE31, .is_rmii = 1, }; @@ -190,6 +192,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = { .enable_pin = AT91_PIN_PD15, .parts = neocore926_nand_partition, .num_parts = ARRAY_SIZE(neocore926_nand_partition), + .det_pin = -EINVAL, }; static struct sam9_smc_config __initdata neocore926_nand_smc_config = { @@ -213,7 +216,7 @@ static struct sam9_smc_config __initdata neocore926_nand_smc_config = { static void __init neocore926_add_device_nand(void) { /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &neocore926_nand_smc_config); + sam9_smc_configure(0, 3, &neocore926_nand_smc_config); at91_add_device_nand(&neocore926_nand_data); } diff --git a/arch/arm/mach-at91/board-pcontrol-g20.c b/arch/arm/mach-at91/board-pcontrol-g20.c index 49e3f699b48e..b4a12fc184c8 100644 --- a/arch/arm/mach-at91/board-pcontrol-g20.c +++ b/arch/arm/mach-at91/board-pcontrol-g20.c @@ -96,9 +96,9 @@ static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { { static void __init add_device_pcontrol(void) { /* configure chip-select 4 (IO compatible to 8051 X4 ) */ - sam9_smc_configure(4, &pcontrol_smc_config[0]); + sam9_smc_configure(0, 4, &pcontrol_smc_config[0]); /* configure chip-select 7 (FerroRAM 256KiBx16bit MR2A16A D4 ) */ - sam9_smc_configure(7, &pcontrol_smc_config[1]); + sam9_smc_configure(0, 7, &pcontrol_smc_config[1]); } @@ -107,6 +107,8 @@ static void __init add_device_pcontrol(void) */ static struct at91_usbh_data __initdata usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; @@ -122,7 +124,7 @@ static struct at91_udc_data __initdata pcontrol_g20_udc_data = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata macb_data = { +static struct macb_platform_data __initdata macb_data = { .phy_irq_pin = AT91_PIN_PA28, .is_rmii = 1, }; diff --git a/arch/arm/mach-at91/board-picotux200.c b/arch/arm/mach-at91/board-picotux200.c index 0a8fe6a1b7c8..ab024fa11d5c 100644 --- a/arch/arm/mach-at91/board-picotux200.c +++ b/arch/arm/mach-at91/board-picotux200.c @@ -60,13 +60,15 @@ static void __init picotux200_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata picotux200_eth_data = { +static struct macb_platform_data __initdata picotux200_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; static struct at91_usbh_data __initdata picotux200_usbh_data = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_mmc_data __initdata picotux200_mmc_data = { @@ -74,6 +76,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = { .slot_b = 0, .wire4 = 1, .wp_pin = AT91_PIN_PA17, + .vcc_pin = -EINVAL, }; #define PICOTUX200_FLASH_BASE AT91_CHIPSELECT_0 diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index 07421bdb88ea..e029d220cb84 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -77,6 +77,8 @@ static void __init ek_init_early(void) */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -84,7 +86,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; /* @@ -104,7 +106,7 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA31, .is_rmii = 1, }; @@ -133,7 +135,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = { static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .parts = ek_nand_partition, @@ -161,7 +163,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -172,9 +174,9 @@ static void __init ek_add_device_nand(void) static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 0, .wire4 = 1, -// .det_pin = ... not connected -// .wp_pin = ... not connected -// .vcc_pin = ... not connected + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; /* @@ -251,7 +253,7 @@ static void __init ek_board_init(void) /* LEDs */ at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds)); /* shutdown controller, wakeup button (5 msec low) */ - at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW + at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW | AT91_SHDW_RTTWKEN); } diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c index 80a8c9c6e922..782f37946af5 100644 --- a/arch/arm/mach-at91/board-rm9200dk.c +++ b/arch/arm/mach-at91/board-rm9200dk.c @@ -65,13 +65,15 @@ static void __init dk_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata dk_eth_data = { +static struct macb_platform_data __initdata dk_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; static struct at91_usbh_data __initdata dk_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata dk_udc_data = { @@ -80,16 +82,19 @@ static struct at91_udc_data __initdata dk_udc_data = { }; static struct at91_cf_data __initdata dk_cf_data = { + .irq_pin = -EINVAL, .det_pin = AT91_PIN_PB0, + .vcc_pin = -EINVAL, .rst_pin = AT91_PIN_PC5, - // .irq_pin = ... not connected - // .vcc_pin = ... always powered }; #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD static struct at91_mmc_data __initdata dk_mmc_data = { .slot_b = 0, .wire4 = 1, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; #endif @@ -143,7 +148,7 @@ static struct atmel_nand_data __initdata dk_nand_data = { .cle = 21, .det_pin = AT91_PIN_PB1, .rdy_pin = AT91_PIN_PC2, - // .enable_pin = ... not there + .enable_pin = -EINVAL, .parts = dk_nand_partition, .num_parts = ARRAY_SIZE(dk_nand_partition), }; diff --git a/arch/arm/mach-at91/board-rm9200ek.c b/arch/arm/mach-at91/board-rm9200ek.c index 99fd7f8aee0e..ef7c12a92246 100644 --- a/arch/arm/mach-at91/board-rm9200ek.c +++ b/arch/arm/mach-at91/board-rm9200ek.c @@ -65,13 +65,15 @@ static void __init ek_init_early(void) at91_set_serial_console(0); } -static struct at91_eth_data __initdata ek_eth_data = { +static struct macb_platform_data __initdata ek_eth_data = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata ek_udc_data = { @@ -85,6 +87,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 0, .wire4 = 1, .wp_pin = AT91_PIN_PA17, + .vcc_pin = -EINVAL, }; #endif diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c index e927df0175df..af0750fafa29 100644 --- a/arch/arm/mach-at91/board-rsi-ews.c +++ b/arch/arm/mach-at91/board-rsi-ews.c @@ -60,7 +60,7 @@ static void __init rsi_ews_init_early(void) /* * Ethernet */ -static struct at91_eth_data rsi_ews_eth_data __initdata = { +static struct macb_platform_data rsi_ews_eth_data __initdata = { .phy_irq_pin = AT91_PIN_PC4, .is_rmii = 1, }; @@ -70,6 +70,8 @@ static struct at91_eth_data rsi_ews_eth_data __initdata = { */ static struct at91_usbh_data rsi_ews_usbh_data __initdata = { .ports = 1, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index 072d53af98d9..84bce587735f 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -72,6 +72,8 @@ static void __init ek_init_early(void) */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -79,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -109,7 +111,7 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 0, }; @@ -134,7 +136,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = { static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .parts = ek_nand_partition, @@ -162,7 +164,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -176,7 +178,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PC8, .wp_pin = AT91_PIN_PC4, -// .vcc_pin = ... not connected + .vcc_pin = -EINVAL, }; static void __init ek_board_init(void) diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index 4f10181a0782..be8233bcabdc 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -75,6 +75,8 @@ static void __init ek_init_early(void) */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -151,7 +153,7 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 1, }; @@ -176,7 +178,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = { static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .parts = ek_nand_partition, @@ -211,7 +213,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -223,9 +225,9 @@ static void __init ek_add_device_nand(void) static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, .wire4 = 1, -// .det_pin = ... not connected -// .wp_pin = ... not connected -// .vcc_pin = ... not connected + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index b005b738e8ff..40895072a1a7 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -131,7 +131,7 @@ static struct sam9_smc_config __initdata dm9000_smc_config = { static void __init ek_add_device_dm9000(void) { /* Configure chip-select 2 (DM9000) */ - sam9_smc_configure(2, &dm9000_smc_config); + sam9_smc_configure(0, 2, &dm9000_smc_config); /* Configure Reset signal as output */ at91_set_gpio_output(AT91_PIN_PC10, 0); @@ -151,6 +151,8 @@ static void __init ek_add_device_dm9000(void) {} */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; @@ -159,7 +161,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PB29, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -182,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = { static struct atmel_nand_data __initdata ek_nand_data = { .ale = 22, .cle = 21, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC15, .enable_pin = AT91_PIN_PC14, .parts = ek_nand_partition, @@ -217,7 +219,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -345,6 +347,9 @@ static struct spi_board_info ek_spi_devices[] = { */ static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; #endif /* CONFIG_SPI_ATMEL_* */ diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index bccdcf23caa1..29f66052fe63 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -74,6 +74,7 @@ static void __init ek_init_early(void) static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 }, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -81,7 +82,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PA25, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -151,14 +152,14 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PE18, .wp_pin = AT91_PIN_PE19, -// .vcc_pin = ... not connected + .vcc_pin = -EINVAL, }; /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PE31, .is_rmii = 1, }; @@ -183,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = { static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PA22, .enable_pin = AT91_PIN_PD15, .parts = ek_nand_partition, @@ -218,7 +219,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -353,6 +354,7 @@ static void __init ek_add_device_buttons(void) {} * reset_pin is not connected: NRST */ static struct ac97c_platform_data ek_ac97_data = { + .reset_pin = -EINVAL, }; diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 64fc75c9d0ac..843d6286c6f4 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -86,6 +86,8 @@ static void __init ek_init_early(void) */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -93,7 +95,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PC5, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; @@ -123,7 +125,7 @@ static struct spi_board_info ek_spi_devices[] = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PA7, .is_rmii = 1, }; @@ -163,6 +165,7 @@ static struct atmel_nand_data __initdata ek_nand_data = { .cle = 22, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, + .det_pin = -EINVAL, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; @@ -195,7 +198,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -210,6 +213,7 @@ static struct mci_platform_data __initdata ek_mmc_data = { .slot[1] = { .bus_width = 4, .detect_pin = AT91_PIN_PC9, + .wp_pin = -EINVAL, }, }; @@ -218,6 +222,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = { .slot_b = 1, /* Only one slot so use slot B */ .wire4 = 1, .det_pin = AT91_PIN_PC9, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; #endif @@ -227,6 +233,7 @@ static void __init ek_add_device_mmc(void) if (ek_have_2mmc()) { ek_mmc_data.slot[0].bus_width = 4; ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2; + ek_mmc_data.slot[0].wp_pin = -1; } at91_add_device_mci(0, &ek_mmc_data); #else diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index 92de9127923a..ea0d1b9c2b7b 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -69,6 +69,7 @@ static void __init ek_init_early(void) static struct at91_usbh_data __initdata ek_usbh_hs_data = { .ports = 2, .vbus_pin = {AT91_PIN_PD1, AT91_PIN_PD3}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; @@ -100,6 +101,7 @@ static struct mci_platform_data __initdata mci0_data = { .slot[0] = { .bus_width = 4, .detect_pin = AT91_PIN_PD10, + .wp_pin = -EINVAL, }, }; @@ -115,7 +117,7 @@ static struct mci_platform_data __initdata mci1_data = { /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PD5, .is_rmii = 1, }; @@ -143,6 +145,7 @@ static struct atmel_nand_data __initdata ek_nand_data = { .cle = 22, .rdy_pin = AT91_PIN_PC8, .enable_pin = AT91_PIN_PC14, + .det_pin = -EINVAL, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; @@ -175,7 +178,7 @@ static void __init ek_add_device_nand(void) ek_nand_smc_config.mode |= AT91_SMC_DBW_8; /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -330,6 +333,7 @@ static void __init ek_add_device_buttons(void) {} * reset_pin is not connected: NRST */ static struct ac97c_platform_data ek_ac97_data = { + .reset_pin = -EINVAL, }; diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index b2b748239f36..c1366d0032bf 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = { static struct at91_mmc_data __initdata ek_mmc_data = { .wire4 = 1, .det_pin = AT91_PIN_PA15, -// .wp_pin = ... not connected -// .vcc_pin = ... not connected + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; @@ -91,7 +91,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = { static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PD17, .enable_pin = AT91_PIN_PB6, .parts = ek_nand_partition, @@ -119,7 +119,7 @@ static struct sam9_smc_config __initdata ek_nand_smc_config = { static void __init ek_add_device_nand(void) { /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &ek_nand_smc_config); + sam9_smc_configure(0, 3, &ek_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -204,6 +204,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data; * reset_pin is not connected: NRST */ static struct ac97c_platform_data ek_ac97_data = { + .reset_pin = -EINVAL, }; diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c index 0df01c6e2d0c..4770db08e5a6 100644 --- a/arch/arm/mach-at91/board-snapper9260.c +++ b/arch/arm/mach-at91/board-snapper9260.c @@ -57,15 +57,19 @@ static void __init snapper9260_init_early(void) static struct at91_usbh_data __initdata snapper9260_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; static struct at91_udc_data __initdata snapper9260_udc_data = { .vbus_pin = SNAPPER9260_IO_EXP_GPIO(5), .vbus_active_low = 1, .vbus_polled = 1, + .pullup_pin = -EINVAL, }; -static struct at91_eth_data snapper9260_macb_data = { +static struct macb_platform_data snapper9260_macb_data = { + .phy_irq_pin = -EINVAL, .is_rmii = 1, }; @@ -104,6 +108,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = { .parts = snapper9260_nand_partitions, .num_parts = ARRAY_SIZE(snapper9260_nand_partitions), .bus_width_16 = 0, + .enable_pin = -EINVAL, + .det_pin = -EINVAL, }; static struct sam9_smc_config __initdata snapper9260_nand_smc_config = { @@ -149,7 +155,7 @@ static struct i2c_board_info __initdata snapper9260_i2c_devices[] = { static void __init snapper9260_add_device_nand(void) { at91_set_A_periph(AT91_PIN_PC14, 0); - sam9_smc_configure(3, &snapper9260_nand_smc_config); + sam9_smc_configure(0, 3, &snapper9260_nand_smc_config); at91_add_device_nand(&snapper9260_nand_data); } diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 936e5fd7f406..e8d3d5b88244 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = { .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .bus_width_16 = 0, + .det_pin = -EINVAL, }; static struct sam9_smc_config __initdata nand_smc_config = { @@ -108,7 +109,7 @@ static struct sam9_smc_config __initdata nand_smc_config = { static void __init add_device_nand(void) { /* configure chip-select 3 (NAND) */ - sam9_smc_configure(3, &nand_smc_config); + sam9_smc_configure(0, 3, &nand_smc_config); at91_add_device_nand(&nand_data); } @@ -122,12 +123,17 @@ static void __init add_device_nand(void) static struct mci_platform_data __initdata mmc_data = { .slot[0] = { .bus_width = 4, + .detect_pin = -1; + .wp_pin = -1; }, }; #else static struct at91_mmc_data __initdata mmc_data = { .slot_b = 0, .wire4 = 1, + .det_pin = -EINVAL, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; #endif @@ -137,6 +143,8 @@ static struct at91_mmc_data __initdata mmc_data = { */ static struct at91_usbh_data __initdata usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; @@ -145,19 +153,19 @@ static struct at91_usbh_data __initdata usbh_data = { */ static struct at91_udc_data __initdata portuxg20_udc_data = { .vbus_pin = AT91_PIN_PC7, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; static struct at91_udc_data __initdata stamp9g20evb_udc_data = { .vbus_pin = AT91_PIN_PA22, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; /* * MACB Ethernet device */ -static struct at91_eth_data __initdata macb_data = { +static struct macb_platform_data __initdata macb_data = { .phy_irq_pin = AT91_PIN_PA28, .is_rmii = 1, }; diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index 0a20bab21f99..26c36fc2d1e5 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -66,6 +66,8 @@ static void __init ek_init_early(void) */ static struct at91_usbh_data __initdata ek_usbh_data = { .ports = 2, + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -73,7 +75,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = { */ static struct at91_udc_data __initdata ek_udc_data = { .vbus_pin = AT91_PIN_PB11, - .pullup_pin = 0, /* pull-up driven by UDC */ + .pullup_pin = -EINVAL, /* pull-up driven by UDC */ }; static void __init ek_add_device_udc(void) @@ -146,7 +148,7 @@ static void __init ek_add_device_spi(void) /* * MACB Ethernet device */ -static struct at91_eth_data __initdata ek_macb_data = { +static struct macb_platform_data __initdata ek_macb_data = { .phy_irq_pin = AT91_PIN_PE31, .is_rmii = 1, }; @@ -193,7 +195,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = { static struct atmel_nand_data __initdata ek_nand_data = { .ale = 21, .cle = 22, -// .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PA22, .enable_pin = AT91_PIN_PD15, .parts = ek_nand_partition, @@ -245,9 +247,9 @@ static void __init ek_add_device_nand(void) /* configure chip-select 3 (NAND) */ if (machine_is_usb_a9g20()) - sam9_smc_configure(3, &usb_a9g20_nand_smc_config); + sam9_smc_configure(0, 3, &usb_a9g20_nand_smc_config); else - sam9_smc_configure(3, &usb_a9260_nand_smc_config); + sam9_smc_configure(0, 3, &usb_a9260_nand_smc_config); at91_add_device_nand(&ek_nand_data); } @@ -344,7 +346,7 @@ static void __init ek_board_init(void) /* I2C */ at91_add_device_i2c(NULL, 0); /* shutdown controller, wakeup button (5 msec low) */ - at91_sys_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) + at91_shdwc_write(AT91_SHDW_MR, AT91_SHDW_CPTWK0_(10) | AT91_SHDW_WKMODE0_LOW | AT91_SHDW_RTTWKEN); } diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index 12a3f955162b..bbd553e1cd93 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -110,7 +110,7 @@ static struct gpio_led yl9200_leds[] = { /* * Ethernet */ -static struct at91_eth_data __initdata yl9200_eth_data = { +static struct macb_platform_data __initdata yl9200_eth_data = { .phy_irq_pin = AT91_PIN_PB28, .is_rmii = 1, }; @@ -120,6 +120,8 @@ static struct at91_eth_data __initdata yl9200_eth_data = { */ static struct at91_usbh_data __initdata yl9200_usbh_data = { .ports = 1, /* PQFP version of AT91RM9200 */ + .vbus_pin = {-EINVAL, -EINVAL}, + .overcurrent_pin= {-EINVAL, -EINVAL}, }; /* @@ -137,8 +139,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = { */ static struct at91_mmc_data __initdata yl9200_mmc_data = { .det_pin = AT91_PIN_PB9, - // .wp_pin = ... not connected .wire4 = 1, + .wp_pin = -EINVAL, + .vcc_pin = -EINVAL, }; /* @@ -175,7 +178,7 @@ static struct mtd_partition __initdata yl9200_nand_partition[] = { static struct atmel_nand_data __initdata yl9200_nand_data = { .ale = 6, .cle = 7, - // .det_pin = ... not connected + .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */ .enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */ .parts = yl9200_nand_partition, diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h index 938b34f57741..40309588f360 100644 --- a/arch/arm/mach-at91/generic.h +++ b/arch/arm/mach-at91/generic.h @@ -29,6 +29,7 @@ extern void __init at91_aic_init(unsigned int priority[]); /* Timer */ struct sys_timer; extern struct sys_timer at91rm9200_timer; +extern void at91sam926x_ioremap_pit(u32 addr); extern struct sys_timer at91sam926x_timer; extern struct sys_timer at91x40_timer; @@ -59,14 +60,16 @@ extern void at91_irq_resume(void); /* reset */ extern void at91sam9_alt_reset(void); +/* shutdown */ +extern void at91_ioremap_shdwc(u32 base_addr); + /* GPIO */ #define AT91RM9200_PQFP 3 /* AT91RM9200 PQFP package has 3 banks */ #define AT91RM9200_BGA 4 /* AT91RM9200 BGA package has 4 banks */ struct at91_gpio_bank { unsigned short id; /* peripheral ID */ - unsigned long offset; /* offset from system peripheral base */ - struct clk *clock; /* associated clock */ + unsigned long regbase; /* offset from system peripheral base */ }; extern void __init at91_gpio_init(struct at91_gpio_bank *, int nr_banks); extern void __init at91_gpio_irq_setup(void); diff --git a/arch/arm/mach-at91/gpio.c b/arch/arm/mach-at91/gpio.c index 224e9e2f8674..74d6783eeabb 100644 --- a/arch/arm/mach-at91/gpio.c +++ b/arch/arm/mach-at91/gpio.c @@ -29,8 +29,9 @@ struct at91_gpio_chip { struct gpio_chip chip; struct at91_gpio_chip *next; /* Bank sharing same clock */ - struct at91_gpio_bank *bank; /* Bank definition */ + int id; /* ID of register bank */ void __iomem *regbase; /* Base of register bank */ + struct clk *clock; /* associated clock */ }; #define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip) @@ -58,18 +59,17 @@ static int at91_gpiolib_direction_input(struct gpio_chip *chip, } static struct at91_gpio_chip gpio_chip[] = { - AT91_GPIO_CHIP("A", 0x00 + PIN_BASE, 32), - AT91_GPIO_CHIP("B", 0x20 + PIN_BASE, 32), - AT91_GPIO_CHIP("C", 0x40 + PIN_BASE, 32), - AT91_GPIO_CHIP("D", 0x60 + PIN_BASE, 32), - AT91_GPIO_CHIP("E", 0x80 + PIN_BASE, 32), + AT91_GPIO_CHIP("pioA", 0x00, 32), + AT91_GPIO_CHIP("pioB", 0x20, 32), + AT91_GPIO_CHIP("pioC", 0x40, 32), + AT91_GPIO_CHIP("pioD", 0x60, 32), + AT91_GPIO_CHIP("pioE", 0x80, 32), }; static int gpio_banks; static inline void __iomem *pin_to_controller(unsigned pin) { - pin -= PIN_BASE; pin /= 32; if (likely(pin < gpio_banks)) return gpio_chip[pin].regbase; @@ -79,7 +79,6 @@ static inline void __iomem *pin_to_controller(unsigned pin) static inline unsigned pin_to_mask(unsigned pin) { - pin -= PIN_BASE; return 1 << (pin % 32); } @@ -274,8 +273,9 @@ static u32 backups[MAX_GPIO_BANKS]; static int gpio_irq_set_wake(struct irq_data *d, unsigned state) { - unsigned mask = pin_to_mask(d->irq); - unsigned bank = (d->irq - PIN_BASE) / 32; + unsigned pin = irq_to_gpio(d->irq); + unsigned mask = pin_to_mask(pin); + unsigned bank = pin / 32; if (unlikely(bank >= MAX_GPIO_BANKS)) return -EINVAL; @@ -285,7 +285,7 @@ static int gpio_irq_set_wake(struct irq_data *d, unsigned state) else wakeups[bank] &= ~mask; - irq_set_irq_wake(gpio_chip[bank].bank->id, state); + irq_set_irq_wake(gpio_chip[bank].id, state); return 0; } @@ -302,7 +302,7 @@ void at91_gpio_suspend(void) __raw_writel(wakeups[i], pio + PIO_IER); if (!wakeups[i]) - clk_disable(gpio_chip[i].bank->clock); + clk_disable(gpio_chip[i].clock); else { #ifdef CONFIG_PM_DEBUG printk(KERN_DEBUG "GPIO-%c may wake for %08x\n", 'A'+i, wakeups[i]); @@ -319,7 +319,7 @@ void at91_gpio_resume(void) void __iomem *pio = gpio_chip[i].regbase; if (!wakeups[i]) - clk_enable(gpio_chip[i].bank->clock); + clk_enable(gpio_chip[i].clock); __raw_writel(wakeups[i], pio + PIO_IDR); __raw_writel(backups[i], pio + PIO_IER); @@ -344,8 +344,9 @@ void at91_gpio_resume(void) static void gpio_irq_mask(struct irq_data *d) { - void __iomem *pio = pin_to_controller(d->irq); - unsigned mask = pin_to_mask(d->irq); + unsigned pin = irq_to_gpio(d->irq); + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); if (pio) __raw_writel(mask, pio + PIO_IDR); @@ -353,8 +354,9 @@ static void gpio_irq_mask(struct irq_data *d) static void gpio_irq_unmask(struct irq_data *d) { - void __iomem *pio = pin_to_controller(d->irq); - unsigned mask = pin_to_mask(d->irq); + unsigned pin = irq_to_gpio(d->irq); + void __iomem *pio = pin_to_controller(pin); + unsigned mask = pin_to_mask(pin); if (pio) __raw_writel(mask, pio + PIO_IER); @@ -382,7 +384,7 @@ static struct irq_chip gpio_irqchip = { static void gpio_irq_handler(unsigned irq, struct irq_desc *desc) { - unsigned pin; + unsigned irq_pin; struct irq_data *idata = irq_desc_get_irq_data(desc); struct irq_chip *chip = irq_data_get_irq_chip(idata); struct at91_gpio_chip *at91_gpio = irq_data_get_irq_chip_data(idata); @@ -405,12 +407,12 @@ static void gpio_irq_handler(unsigned irq, struct irq_desc *desc) continue; } - pin = at91_gpio->chip.base; + irq_pin = gpio_to_irq(at91_gpio->chip.base); while (isr) { if (isr & 1) - generic_handle_irq(pin); - pin++; + generic_handle_irq(irq_pin); + irq_pin++; isr >>= 1; } } @@ -438,7 +440,7 @@ static int at91_gpio_show(struct seq_file *s, void *unused) seq_printf(s, "%i:\t", j); for (bank = 0; bank < gpio_banks; bank++) { - unsigned pin = PIN_BASE + (32 * bank) + j; + unsigned pin = (32 * bank) + j; void __iomem *pio = pin_to_controller(pin); unsigned mask = pin_to_mask(pin); @@ -491,27 +493,28 @@ static struct lock_class_key gpio_lock_class; */ void __init at91_gpio_irq_setup(void) { - unsigned pioc, pin; + unsigned pioc, irq = gpio_to_irq(0); struct at91_gpio_chip *this, *prev; - for (pioc = 0, pin = PIN_BASE, this = gpio_chip, prev = NULL; + for (pioc = 0, this = gpio_chip, prev = NULL; pioc++ < gpio_banks; prev = this, this++) { - unsigned id = this->bank->id; + unsigned id = this->id; unsigned i; __raw_writel(~0, this->regbase + PIO_IDR); - for (i = 0, pin = this->chip.base; i < 32; i++, pin++) { - irq_set_lockdep_class(pin, &gpio_lock_class); + for (i = 0, irq = gpio_to_irq(this->chip.base); i < 32; + i++, irq++) { + irq_set_lockdep_class(irq, &gpio_lock_class); /* * Can use the "simple" and not "edge" handler since it's * shorter, and the AIC handles interrupts sanely. */ - irq_set_chip_and_handler(pin, &gpio_irqchip, + irq_set_chip_and_handler(irq, &gpio_irqchip, handle_simple_irq); - set_irq_flags(pin, IRQF_VALID); + set_irq_flags(irq, IRQF_VALID); } /* The toplevel handler handles one bank of GPIOs, except @@ -524,7 +527,7 @@ void __init at91_gpio_irq_setup(void) irq_set_chip_data(id, this); irq_set_chained_handler(id, gpio_irq_handler); } - pr_info("AT91: %d gpio irqs in %d banks\n", pin - PIN_BASE, gpio_banks); + pr_info("AT91: %d gpio irqs in %d banks\n", irq - gpio_to_irq(0), gpio_banks); } /* gpiolib support */ @@ -612,16 +615,26 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks) for (i = 0; i < nr_banks; i++) { at91_gpio = &gpio_chip[i]; - at91_gpio->bank = &data[i]; - at91_gpio->chip.base = PIN_BASE + i * 32; - at91_gpio->regbase = at91_gpio->bank->offset + - (void __iomem *)AT91_VA_BASE_SYS; + at91_gpio->id = data[i].id; + at91_gpio->chip.base = i * 32; + + at91_gpio->regbase = ioremap(data[i].regbase, 512); + if (!at91_gpio->regbase) { + pr_err("at91_gpio.%d, failed to map registers, ignoring.\n", i); + continue; + } + + at91_gpio->clock = clk_get_sys(NULL, at91_gpio->chip.label); + if (!at91_gpio->clock) { + pr_err("at91_gpio.%d, failed to get clock, ignoring.\n", i); + continue; + } /* enable PIO controller's clock */ - clk_enable(at91_gpio->bank->clock); + clk_enable(at91_gpio->clock); /* AT91SAM9263_ID_PIOCDE groups PIOC, PIOD, PIOE */ - if (last && last->bank->id == at91_gpio->bank->id) + if (last && last->id == at91_gpio->id) last->next = at91_gpio; last = at91_gpio; diff --git a/arch/arm/mach-at91/include/mach/at91_aic.h b/arch/arm/mach-at91/include/mach/at91_aic.h index 03566799d3be..3045781c473f 100644 --- a/arch/arm/mach-at91/include/mach/at91_aic.h +++ b/arch/arm/mach-at91/include/mach/at91_aic.h @@ -16,7 +16,19 @@ #ifndef AT91_AIC_H #define AT91_AIC_H -#define AT91_AIC_SMR(n) (AT91_AIC + ((n) * 4)) /* Source Mode Registers 0-31 */ +#ifndef __ASSEMBLY__ +extern void __iomem *at91_aic_base; + +#define at91_aic_read(field) \ + __raw_readl(at91_aic_base + field) + +#define at91_aic_write(field, value) \ + __raw_writel(value, at91_aic_base + field); +#else +.extern at91_aic_base +#endif + +#define AT91_AIC_SMR(n) ((n) * 4) /* Source Mode Registers 0-31 */ #define AT91_AIC_PRIOR (7 << 0) /* Priority Level */ #define AT91_AIC_SRCTYPE (3 << 5) /* Interrupt Source Type */ #define AT91_AIC_SRCTYPE_LOW (0 << 5) @@ -24,30 +36,30 @@ #define AT91_AIC_SRCTYPE_HIGH (2 << 5) #define AT91_AIC_SRCTYPE_RISING (3 << 5) -#define AT91_AIC_SVR(n) (AT91_AIC + 0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */ -#define AT91_AIC_IVR (AT91_AIC + 0x100) /* Interrupt Vector Register */ -#define AT91_AIC_FVR (AT91_AIC + 0x104) /* Fast Interrupt Vector Register */ -#define AT91_AIC_ISR (AT91_AIC + 0x108) /* Interrupt Status Register */ +#define AT91_AIC_SVR(n) (0x80 + ((n) * 4)) /* Source Vector Registers 0-31 */ +#define AT91_AIC_IVR 0x100 /* Interrupt Vector Register */ +#define AT91_AIC_FVR 0x104 /* Fast Interrupt Vector Register */ +#define AT91_AIC_ISR 0x108 /* Interrupt Status Register */ #define AT91_AIC_IRQID (0x1f << 0) /* Current Interrupt Identifier */ -#define AT91_AIC_IPR (AT91_AIC + 0x10c) /* Interrupt Pending Register */ -#define AT91_AIC_IMR (AT91_AIC + 0x110) /* Interrupt Mask Register */ -#define AT91_AIC_CISR (AT91_AIC + 0x114) /* Core Interrupt Status Register */ +#define AT91_AIC_IPR 0x10c /* Interrupt Pending Register */ +#define AT91_AIC_IMR 0x110 /* Interrupt Mask Register */ +#define AT91_AIC_CISR 0x114 /* Core Interrupt Status Register */ #define AT91_AIC_NFIQ (1 << 0) /* nFIQ Status */ #define AT91_AIC_NIRQ (1 << 1) /* nIRQ Status */ -#define AT91_AIC_IECR (AT91_AIC + 0x120) /* Interrupt Enable Command Register */ -#define AT91_AIC_IDCR (AT91_AIC + 0x124) /* Interrupt Disable Command Register */ -#define AT91_AIC_ICCR (AT91_AIC + 0x128) /* Interrupt Clear Command Register */ -#define AT91_AIC_ISCR (AT91_AIC + 0x12c) /* Interrupt Set Command Register */ -#define AT91_AIC_EOICR (AT91_AIC + 0x130) /* End of Interrupt Command Register */ -#define AT91_AIC_SPU (AT91_AIC + 0x134) /* Spurious Interrupt Vector Register */ -#define AT91_AIC_DCR (AT91_AIC + 0x138) /* Debug Control Register */ +#define AT91_AIC_IECR 0x120 /* Interrupt Enable Command Register */ +#define AT91_AIC_IDCR 0x124 /* Interrupt Disable Command Register */ +#define AT91_AIC_ICCR 0x128 /* Interrupt Clear Command Register */ +#define AT91_AIC_ISCR 0x12c /* Interrupt Set Command Register */ +#define AT91_AIC_EOICR 0x130 /* End of Interrupt Command Register */ +#define AT91_AIC_SPU 0x134 /* Spurious Interrupt Vector Register */ +#define AT91_AIC_DCR 0x138 /* Debug Control Register */ #define AT91_AIC_DCR_PROT (1 << 0) /* Protection Mode */ #define AT91_AIC_DCR_GMSK (1 << 1) /* General Mask */ -#define AT91_AIC_FFER (AT91_AIC + 0x140) /* Fast Forcing Enable Register [SAM9 only] */ -#define AT91_AIC_FFDR (AT91_AIC + 0x144) /* Fast Forcing Disable Register [SAM9 only] */ -#define AT91_AIC_FFSR (AT91_AIC + 0x148) /* Fast Forcing Status Register [SAM9 only] */ +#define AT91_AIC_FFER 0x140 /* Fast Forcing Enable Register [SAM9 only] */ +#define AT91_AIC_FFDR 0x144 /* Fast Forcing Disable Register [SAM9 only] */ +#define AT91_AIC_FFSR 0x148 /* Fast Forcing Status Register [SAM9 only] */ #endif diff --git a/arch/arm/mach-at91/include/mach/at91_dbgu.h b/arch/arm/mach-at91/include/mach/at91_dbgu.h index dbfe455a4c41..2aa0c5e13495 100644 --- a/arch/arm/mach-at91/include/mach/at91_dbgu.h +++ b/arch/arm/mach-at91/include/mach/at91_dbgu.h @@ -19,7 +19,7 @@ #define dbgu_readl(dbgu, field) \ __raw_readl(AT91_VA_BASE_SYS + dbgu + AT91_DBGU_ ## field) -#ifdef AT91_DBGU +#if !defined(CONFIG_ARCH_AT91X40) #define AT91_DBGU_CR (0x00) /* Control Register */ #define AT91_DBGU_MR (0x04) /* Mode Register */ #define AT91_DBGU_IER (0x08) /* Interrupt Enable Register */ diff --git a/arch/arm/mach-at91/include/mach/at91_pit.h b/arch/arm/mach-at91/include/mach/at91_pit.h index 974d0bd05b5b..d1f80ad7f4d4 100644 --- a/arch/arm/mach-at91/include/mach/at91_pit.h +++ b/arch/arm/mach-at91/include/mach/at91_pit.h @@ -16,16 +16,16 @@ #ifndef AT91_PIT_H #define AT91_PIT_H -#define AT91_PIT_MR (AT91_PIT + 0x00) /* Mode Register */ +#define AT91_PIT_MR 0x00 /* Mode Register */ #define AT91_PIT_PITIEN (1 << 25) /* Timer Interrupt Enable */ #define AT91_PIT_PITEN (1 << 24) /* Timer Enabled */ #define AT91_PIT_PIV (0xfffff) /* Periodic Interval Value */ -#define AT91_PIT_SR (AT91_PIT + 0x04) /* Status Register */ +#define AT91_PIT_SR 0x04 /* Status Register */ #define AT91_PIT_PITS (1 << 0) /* Timer Status */ -#define AT91_PIT_PIVR (AT91_PIT + 0x08) /* Periodic Interval Value Register */ -#define AT91_PIT_PIIR (AT91_PIT + 0x0c) /* Periodic Interval Image Register */ +#define AT91_PIT_PIVR 0x08 /* Periodic Interval Value Register */ +#define AT91_PIT_PIIR 0x0c /* Periodic Interval Image Register */ #define AT91_PIT_PICNT (0xfff << 20) /* Interval Counter */ #define AT91_PIT_CPIV (0xfffff) /* Inverval Value */ diff --git a/arch/arm/mach-at91/include/mach/at91_rtc.h b/arch/arm/mach-at91/include/mach/at91_rtc.h index e56f4701a3e5..da1945e5f714 100644 --- a/arch/arm/mach-at91/include/mach/at91_rtc.h +++ b/arch/arm/mach-at91/include/mach/at91_rtc.h @@ -16,7 +16,7 @@ #ifndef AT91_RTC_H #define AT91_RTC_H -#define AT91_RTC_CR (AT91_RTC + 0x00) /* Control Register */ +#define AT91_RTC_CR 0x00 /* Control Register */ #define AT91_RTC_UPDTIM (1 << 0) /* Update Request Time Register */ #define AT91_RTC_UPDCAL (1 << 1) /* Update Request Calendar Register */ #define AT91_RTC_TIMEVSEL (3 << 8) /* Time Event Selection */ @@ -29,44 +29,44 @@ #define AT91_RTC_CALEVSEL_MONTH (1 << 16) #define AT91_RTC_CALEVSEL_YEAR (2 << 16) -#define AT91_RTC_MR (AT91_RTC + 0x04) /* Mode Register */ +#define AT91_RTC_MR 0x04 /* Mode Register */ #define AT91_RTC_HRMOD (1 << 0) /* 12/24 Hour Mode */ -#define AT91_RTC_TIMR (AT91_RTC + 0x08) /* Time Register */ +#define AT91_RTC_TIMR 0x08 /* Time Register */ #define AT91_RTC_SEC (0x7f << 0) /* Current Second */ #define AT91_RTC_MIN (0x7f << 8) /* Current Minute */ #define AT91_RTC_HOUR (0x3f << 16) /* Current Hour */ #define AT91_RTC_AMPM (1 << 22) /* Ante Meridiem Post Meridiem Indicator */ -#define AT91_RTC_CALR (AT91_RTC + 0x0c) /* Calendar Register */ +#define AT91_RTC_CALR 0x0c /* Calendar Register */ #define AT91_RTC_CENT (0x7f << 0) /* Current Century */ #define AT91_RTC_YEAR (0xff << 8) /* Current Year */ #define AT91_RTC_MONTH (0x1f << 16) /* Current Month */ #define AT91_RTC_DAY (7 << 21) /* Current Day */ #define AT91_RTC_DATE (0x3f << 24) /* Current Date */ -#define AT91_RTC_TIMALR (AT91_RTC + 0x10) /* Time Alarm Register */ +#define AT91_RTC_TIMALR 0x10 /* Time Alarm Register */ #define AT91_RTC_SECEN (1 << 7) /* Second Alarm Enable */ #define AT91_RTC_MINEN (1 << 15) /* Minute Alarm Enable */ #define AT91_RTC_HOUREN (1 << 23) /* Hour Alarm Enable */ -#define AT91_RTC_CALALR (AT91_RTC + 0x14) /* Calendar Alarm Register */ +#define AT91_RTC_CALALR 0x14 /* Calendar Alarm Register */ #define AT91_RTC_MTHEN (1 << 23) /* Month Alarm Enable */ #define AT91_RTC_DATEEN (1 << 31) /* Date Alarm Enable */ -#define AT91_RTC_SR (AT91_RTC + 0x18) /* Status Register */ +#define AT91_RTC_SR 0x18 /* Status Register */ #define AT91_RTC_ACKUPD (1 << 0) /* Acknowledge for Update */ #define AT91_RTC_ALARM (1 << 1) /* Alarm Flag */ #define AT91_RTC_SECEV (1 << 2) /* Second Event */ #define AT91_RTC_TIMEV (1 << 3) /* Time Event */ #define AT91_RTC_CALEV (1 << 4) /* Calendar Event */ -#define AT91_RTC_SCCR (AT91_RTC + 0x1c) /* Status Clear Command Register */ -#define AT91_RTC_IER (AT91_RTC + 0x20) /* Interrupt Enable Register */ -#define AT91_RTC_IDR (AT91_RTC + 0x24) /* Interrupt Disable Register */ -#define AT91_RTC_IMR (AT91_RTC + 0x28) /* Interrupt Mask Register */ +#define AT91_RTC_SCCR 0x1c /* Status Clear Command Register */ +#define AT91_RTC_IER 0x20 /* Interrupt Enable Register */ +#define AT91_RTC_IDR 0x24 /* Interrupt Disable Register */ +#define AT91_RTC_IMR 0x28 /* Interrupt Mask Register */ -#define AT91_RTC_VER (AT91_RTC + 0x2c) /* Valid Entry Register */ +#define AT91_RTC_VER 0x2c /* Valid Entry Register */ #define AT91_RTC_NVTIM (1 << 0) /* Non valid Time */ #define AT91_RTC_NVCAL (1 << 1) /* Non valid Calendar */ #define AT91_RTC_NVTIMALR (1 << 2) /* Non valid Time Alarm */ diff --git a/arch/arm/mach-at91/include/mach/at91_shdwc.h b/arch/arm/mach-at91/include/mach/at91_shdwc.h index c4ce07e8a8fa..1d4fe822c77a 100644 --- a/arch/arm/mach-at91/include/mach/at91_shdwc.h +++ b/arch/arm/mach-at91/include/mach/at91_shdwc.h @@ -16,11 +16,21 @@ #ifndef AT91_SHDWC_H #define AT91_SHDWC_H -#define AT91_SHDW_CR (AT91_SHDWC + 0x00) /* Shut Down Control Register */ +#ifndef __ASSEMBLY__ +extern void __iomem *at91_shdwc_base; + +#define at91_shdwc_read(field) \ + __raw_readl(at91_shdwc_base + field) + +#define at91_shdwc_write(field, value) \ + __raw_writel(value, at91_shdwc_base + field); +#endif + +#define AT91_SHDW_CR 0x00 /* Shut Down Control Register */ #define AT91_SHDW_SHDW (1 << 0) /* Shut Down command */ #define AT91_SHDW_KEY (0xa5 << 24) /* KEY Password */ -#define AT91_SHDW_MR (AT91_SHDWC + 0x04) /* Shut Down Mode Register */ +#define AT91_SHDW_MR 0x04 /* Shut Down Mode Register */ #define AT91_SHDW_WKMODE0 (3 << 0) /* Wake-up 0 Mode Selection */ #define AT91_SHDW_WKMODE0_NONE 0 #define AT91_SHDW_WKMODE0_HIGH 1 @@ -30,7 +40,7 @@ #define AT91_SHDW_CPTWK0_(x) ((x) << 4) #define AT91_SHDW_RTTWKEN (1 << 16) /* Real Time Timer Wake-up Enable */ -#define AT91_SHDW_SR (AT91_SHDWC + 0x08) /* Shut Down Status Register */ +#define AT91_SHDW_SR 0x08 /* Shut Down Status Register */ #define AT91_SHDW_WAKEUP0 (1 << 0) /* Wake-up 0 Status */ #define AT91_SHDW_RTTWK (1 << 16) /* Real-time Timer Wake-up */ #define AT91_SHDW_RTCWK (1 << 17) /* Real-time Clock Wake-up [SAM9RL] */ diff --git a/arch/arm/mach-at91/include/mach/at91cap9.h b/arch/arm/mach-at91/include/mach/at91cap9.h index c5df1e8f1955..4c0e2f6011d7 100644 --- a/arch/arm/mach-at91/include/mach/at91cap9.h +++ b/arch/arm/mach-at91/include/mach/at91cap9.h @@ -79,29 +79,28 @@ /* * System Peripherals (offset from AT91_BASE_SYS) */ -#define AT91_ECC (0xffffe200 - AT91_BASE_SYS) #define AT91_BCRAMC (0xffffe400 - AT91_BASE_SYS) #define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS) -#define AT91_SMC (0xffffe800 - AT91_BASE_SYS) #define AT91_MATRIX (0xffffea00 - AT91_BASE_SYS) -#define AT91_CCFG (0xffffeb10 - AT91_BASE_SYS) -#define AT91_DMA (0xffffec00 - AT91_BASE_SYS) -#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS) #define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) #define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) #define AT91_GPBR (cpu_is_at91cap9_revB() ? \ (0xfffffd50 - AT91_BASE_SYS) : \ (0xfffffd60 - AT91_BASE_SYS)) +#define AT91CAP9_BASE_ECC 0xffffe200 +#define AT91CAP9_BASE_DMA 0xffffec00 +#define AT91CAP9_BASE_SMC 0xffffe800 +#define AT91CAP9_BASE_DBGU AT91_BASE_DBGU1 +#define AT91CAP9_BASE_PIOA 0xfffff200 +#define AT91CAP9_BASE_PIOB 0xfffff400 +#define AT91CAP9_BASE_PIOC 0xfffff600 +#define AT91CAP9_BASE_PIOD 0xfffff800 +#define AT91CAP9_BASE_SHDWC 0xfffffd10 +#define AT91CAP9_BASE_RTT 0xfffffd20 +#define AT91CAP9_BASE_PIT 0xfffffd30 +#define AT91CAP9_BASE_WDT 0xfffffd40 + #define AT91_USART0 AT91CAP9_BASE_US0 #define AT91_USART1 AT91CAP9_BASE_US1 #define AT91_USART2 AT91CAP9_BASE_US2 diff --git a/arch/arm/mach-at91/include/mach/at91rm9200.h b/arch/arm/mach-at91/include/mach/at91rm9200.h index e4037b500302..bacb51141819 100644 --- a/arch/arm/mach-at91/include/mach/at91rm9200.h +++ b/arch/arm/mach-at91/include/mach/at91rm9200.h @@ -79,17 +79,17 @@ /* * System Peripherals (offset from AT91_BASE_SYS) */ -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) /* Advanced Interrupt Controller */ -#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) /* Debug Unit */ -#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) /* PIO Controller A */ -#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) /* PIO Controller B */ -#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) /* PIO Controller C */ -#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS) /* PIO Controller D */ #define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) /* Power Management Controller */ #define AT91_ST (0xfffffd00 - AT91_BASE_SYS) /* System Timer */ -#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS) /* Real-Time Clock */ #define AT91_MC (0xffffff00 - AT91_BASE_SYS) /* Memory Controllers */ +#define AT91RM9200_BASE_DBGU AT91_BASE_DBGU0 /* Debug Unit */ +#define AT91RM9200_BASE_PIOA 0xfffff400 /* PIO Controller A */ +#define AT91RM9200_BASE_PIOB 0xfffff600 /* PIO Controller B */ +#define AT91RM9200_BASE_PIOC 0xfffff800 /* PIO Controller C */ +#define AT91RM9200_BASE_PIOD 0xfffffa00 /* PIO Controller D */ +#define AT91RM9200_BASE_RTC 0xfffffe00 /* Real-Time Clock */ + #define AT91_USART0 AT91RM9200_BASE_US0 #define AT91_USART1 AT91RM9200_BASE_US1 #define AT91_USART2 AT91RM9200_BASE_US2 diff --git a/arch/arm/mach-at91/include/mach/at91sam9260.h b/arch/arm/mach-at91/include/mach/at91sam9260.h index 9a791165913f..f937c476bb67 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9260.h +++ b/arch/arm/mach-at91/include/mach/at91sam9260.h @@ -80,24 +80,23 @@ /* * System Peripherals (offset from AT91_BASE_SYS) */ -#define AT91_ECC (0xffffe800 - AT91_BASE_SYS) #define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS) -#define AT91_SMC (0xffffec00 - AT91_BASE_SYS) #define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS) -#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) #define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) #define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) #define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS) +#define AT91SAM9260_BASE_ECC 0xffffe800 +#define AT91SAM9260_BASE_SMC 0xffffec00 +#define AT91SAM9260_BASE_DBGU AT91_BASE_DBGU0 +#define AT91SAM9260_BASE_PIOA 0xfffff400 +#define AT91SAM9260_BASE_PIOB 0xfffff600 +#define AT91SAM9260_BASE_PIOC 0xfffff800 +#define AT91SAM9260_BASE_SHDWC 0xfffffd10 +#define AT91SAM9260_BASE_RTT 0xfffffd20 +#define AT91SAM9260_BASE_PIT 0xfffffd30 +#define AT91SAM9260_BASE_WDT 0xfffffd40 + #define AT91_USART0 AT91SAM9260_BASE_US0 #define AT91_USART1 AT91SAM9260_BASE_US1 #define AT91_USART2 AT91SAM9260_BASE_US2 diff --git a/arch/arm/mach-at91/include/mach/at91sam9261.h b/arch/arm/mach-at91/include/mach/at91sam9261.h index ce596204cefa..175604e261be 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9261.h +++ b/arch/arm/mach-at91/include/mach/at91sam9261.h @@ -66,21 +66,21 @@ * System Peripherals (offset from AT91_BASE_SYS) */ #define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS) -#define AT91_SMC (0xffffec00 - AT91_BASE_SYS) #define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) #define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) #define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) #define AT91_GPBR (0xfffffd50 - AT91_BASE_SYS) +#define AT91SAM9261_BASE_SMC 0xffffec00 +#define AT91SAM9261_BASE_DBGU AT91_BASE_DBGU0 +#define AT91SAM9261_BASE_PIOA 0xfffff400 +#define AT91SAM9261_BASE_PIOB 0xfffff600 +#define AT91SAM9261_BASE_PIOC 0xfffff800 +#define AT91SAM9261_BASE_SHDWC 0xfffffd10 +#define AT91SAM9261_BASE_RTT 0xfffffd20 +#define AT91SAM9261_BASE_PIT 0xfffffd30 +#define AT91SAM9261_BASE_WDT 0xfffffd40 + #define AT91_USART0 AT91SAM9261_BASE_US0 #define AT91_USART1 AT91SAM9261_BASE_US1 #define AT91_USART2 AT91SAM9261_BASE_US2 diff --git a/arch/arm/mach-at91/include/mach/at91sam9263.h b/arch/arm/mach-at91/include/mach/at91sam9263.h index f1b92961a2b1..80c915002d83 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9263.h +++ b/arch/arm/mach-at91/include/mach/at91sam9263.h @@ -74,30 +74,29 @@ /* * System Peripherals (offset from AT91_BASE_SYS) */ -#define AT91_ECC0 (0xffffe000 - AT91_BASE_SYS) #define AT91_SDRAMC0 (0xffffe200 - AT91_BASE_SYS) -#define AT91_SMC0 (0xffffe400 - AT91_BASE_SYS) -#define AT91_ECC1 (0xffffe600 - AT91_BASE_SYS) #define AT91_SDRAMC1 (0xffffe800 - AT91_BASE_SYS) -#define AT91_SMC1 (0xffffea00 - AT91_BASE_SYS) #define AT91_MATRIX (0xffffec00 - AT91_BASE_SYS) -#define AT91_CCFG (0xffffed10 - AT91_BASE_SYS) -#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS) -#define AT91_PIOE (0xfffffa00 - AT91_BASE_SYS) #define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) #define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT0 (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) -#define AT91_RTT1 (0xfffffd50 - AT91_BASE_SYS) #define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS) +#define AT91SAM9263_BASE_ECC0 0xffffe000 +#define AT91SAM9263_BASE_SMC0 0xffffe400 +#define AT91SAM9263_BASE_ECC1 0xffffe600 +#define AT91SAM9263_BASE_SMC1 0xffffea00 +#define AT91SAM9263_BASE_DBGU AT91_BASE_DBGU1 +#define AT91SAM9263_BASE_PIOA 0xfffff200 +#define AT91SAM9263_BASE_PIOB 0xfffff400 +#define AT91SAM9263_BASE_PIOC 0xfffff600 +#define AT91SAM9263_BASE_PIOD 0xfffff800 +#define AT91SAM9263_BASE_PIOE 0xfffffa00 +#define AT91SAM9263_BASE_SHDWC 0xfffffd10 +#define AT91SAM9263_BASE_RTT0 0xfffffd20 +#define AT91SAM9263_BASE_PIT 0xfffffd30 +#define AT91SAM9263_BASE_WDT 0xfffffd40 +#define AT91SAM9263_BASE_RTT1 0xfffffd50 + #define AT91_USART0 AT91SAM9263_BASE_US0 #define AT91_USART1 AT91SAM9263_BASE_US1 #define AT91_USART2 AT91SAM9263_BASE_US2 diff --git a/arch/arm/mach-at91/include/mach/at91sam9_smc.h b/arch/arm/mach-at91/include/mach/at91sam9_smc.h index 57de6207e57e..eb18a70fa647 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9_smc.h +++ b/arch/arm/mach-at91/include/mach/at91sam9_smc.h @@ -16,7 +16,9 @@ #ifndef AT91SAM9_SMC_H #define AT91SAM9_SMC_H -#define AT91_SMC_SETUP(n) (AT91_SMC + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ +#include <mach/cpu.h> + +#define AT91_SMC_SETUP 0x00 /* Setup Register for CS n */ #define AT91_SMC_NWESETUP (0x3f << 0) /* NWE Setup Length */ #define AT91_SMC_NWESETUP_(x) ((x) << 0) #define AT91_SMC_NCS_WRSETUP (0x3f << 8) /* NCS Setup Length in Write Access */ @@ -26,7 +28,7 @@ #define AT91_SMC_NCS_RDSETUP (0x3f << 24) /* NCS Setup Length in Read Access */ #define AT91_SMC_NCS_RDSETUP_(x) ((x) << 24) -#define AT91_SMC_PULSE(n) (AT91_SMC + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ +#define AT91_SMC_PULSE 0x04 /* Pulse Register for CS n */ #define AT91_SMC_NWEPULSE (0x7f << 0) /* NWE Pulse Length */ #define AT91_SMC_NWEPULSE_(x) ((x) << 0) #define AT91_SMC_NCS_WRPULSE (0x7f << 8) /* NCS Pulse Length in Write Access */ @@ -36,13 +38,13 @@ #define AT91_SMC_NCS_RDPULSE (0x7f << 24) /* NCS Pulse Length in Read Access */ #define AT91_SMC_NCS_RDPULSE_(x)((x) << 24) -#define AT91_SMC_CYCLE(n) (AT91_SMC + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ +#define AT91_SMC_CYCLE 0x08 /* Cycle Register for CS n */ #define AT91_SMC_NWECYCLE (0x1ff << 0 ) /* Total Write Cycle Length */ #define AT91_SMC_NWECYCLE_(x) ((x) << 0) #define AT91_SMC_NRDCYCLE (0x1ff << 16) /* Total Read Cycle Length */ #define AT91_SMC_NRDCYCLE_(x) ((x) << 16) -#define AT91_SMC_MODE(n) (AT91_SMC + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ +#define AT91_SMC_MODE 0x0c /* Mode Register for CS n */ #define AT91_SMC_READMODE (1 << 0) /* Read Mode */ #define AT91_SMC_WRITEMODE (1 << 1) /* Write Mode */ #define AT91_SMC_EXNWMODE (3 << 4) /* NWAIT Mode */ @@ -66,11 +68,4 @@ #define AT91_SMC_PS_16 (2 << 28) #define AT91_SMC_PS_32 (3 << 28) -#if defined(AT91_SMC1) /* The AT91SAM9263 has 2 Static Memory contollers */ -#define AT91_SMC1_SETUP(n) (AT91_SMC1 + 0x00 + ((n)*0x10)) /* Setup Register for CS n */ -#define AT91_SMC1_PULSE(n) (AT91_SMC1 + 0x04 + ((n)*0x10)) /* Pulse Register for CS n */ -#define AT91_SMC1_CYCLE(n) (AT91_SMC1 + 0x08 + ((n)*0x10)) /* Cycle Register for CS n */ -#define AT91_SMC1_MODE(n) (AT91_SMC1 + 0x0c + ((n)*0x10)) /* Mode Register for CS n */ -#endif - #endif diff --git a/arch/arm/mach-at91/include/mach/at91sam9g45.h b/arch/arm/mach-at91/include/mach/at91sam9g45.h index 406bb6496805..f0c23c960dec 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9g45.h +++ b/arch/arm/mach-at91/include/mach/at91sam9g45.h @@ -86,27 +86,27 @@ /* * System Peripherals (offset from AT91_BASE_SYS) */ -#define AT91_ECC (0xffffe200 - AT91_BASE_SYS) #define AT91_DDRSDRC1 (0xffffe400 - AT91_BASE_SYS) #define AT91_DDRSDRC0 (0xffffe600 - AT91_BASE_SYS) -#define AT91_SMC (0xffffe800 - AT91_BASE_SYS) #define AT91_MATRIX (0xffffea00 - AT91_BASE_SYS) -#define AT91_DMA (0xffffec00 - AT91_BASE_SYS) -#define AT91_DBGU (0xffffee00 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOD (0xfffff800 - AT91_BASE_SYS) -#define AT91_PIOE (0xfffffa00 - AT91_BASE_SYS) #define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) #define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) #define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS) -#define AT91_RTC (0xfffffdb0 - AT91_BASE_SYS) + +#define AT91SAM9G45_BASE_ECC 0xffffe200 +#define AT91SAM9G45_BASE_DMA 0xffffec00 +#define AT91SAM9G45_BASE_SMC 0xffffe800 +#define AT91SAM9G45_BASE_DBGU AT91_BASE_DBGU1 +#define AT91SAM9G45_BASE_PIOA 0xfffff200 +#define AT91SAM9G45_BASE_PIOB 0xfffff400 +#define AT91SAM9G45_BASE_PIOC 0xfffff600 +#define AT91SAM9G45_BASE_PIOD 0xfffff800 +#define AT91SAM9G45_BASE_PIOE 0xfffffa00 +#define AT91SAM9G45_BASE_SHDWC 0xfffffd10 +#define AT91SAM9G45_BASE_RTT 0xfffffd20 +#define AT91SAM9G45_BASE_PIT 0xfffffd30 +#define AT91SAM9G45_BASE_WDT 0xfffffd40 +#define AT91SAM9G45_BASE_RTC 0xfffffdb0 #define AT91_USART0 AT91SAM9G45_BASE_US0 #define AT91_USART1 AT91SAM9G45_BASE_US1 diff --git a/arch/arm/mach-at91/include/mach/at91sam9rl.h b/arch/arm/mach-at91/include/mach/at91sam9rl.h index 1aabacd315d4..2bb359e60b97 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9rl.h +++ b/arch/arm/mach-at91/include/mach/at91sam9rl.h @@ -69,27 +69,26 @@ /* * System Peripherals (offset from AT91_BASE_SYS) */ -#define AT91_DMA (0xffffe600 - AT91_BASE_SYS) -#define AT91_ECC (0xffffe800 - AT91_BASE_SYS) #define AT91_SDRAMC0 (0xffffea00 - AT91_BASE_SYS) -#define AT91_SMC (0xffffec00 - AT91_BASE_SYS) #define AT91_MATRIX (0xffffee00 - AT91_BASE_SYS) -#define AT91_CCFG (0xffffef10 - AT91_BASE_SYS) -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) -#define AT91_DBGU (0xfffff200 - AT91_BASE_SYS) -#define AT91_PIOA (0xfffff400 - AT91_BASE_SYS) -#define AT91_PIOB (0xfffff600 - AT91_BASE_SYS) -#define AT91_PIOC (0xfffff800 - AT91_BASE_SYS) -#define AT91_PIOD (0xfffffa00 - AT91_BASE_SYS) #define AT91_PMC (0xfffffc00 - AT91_BASE_SYS) #define AT91_RSTC (0xfffffd00 - AT91_BASE_SYS) -#define AT91_SHDWC (0xfffffd10 - AT91_BASE_SYS) -#define AT91_RTT (0xfffffd20 - AT91_BASE_SYS) -#define AT91_PIT (0xfffffd30 - AT91_BASE_SYS) -#define AT91_WDT (0xfffffd40 - AT91_BASE_SYS) #define AT91_SCKCR (0xfffffd50 - AT91_BASE_SYS) #define AT91_GPBR (0xfffffd60 - AT91_BASE_SYS) -#define AT91_RTC (0xfffffe00 - AT91_BASE_SYS) + +#define AT91SAM9RL_BASE_DMA 0xffffe600 +#define AT91SAM9RL_BASE_ECC 0xffffe800 +#define AT91SAM9RL_BASE_SMC 0xffffec00 +#define AT91SAM9RL_BASE_DBGU AT91_BASE_DBGU0 +#define AT91SAM9RL_BASE_PIOA 0xfffff400 +#define AT91SAM9RL_BASE_PIOB 0xfffff600 +#define AT91SAM9RL_BASE_PIOC 0xfffff800 +#define AT91SAM9RL_BASE_PIOD 0xfffffa00 +#define AT91SAM9RL_BASE_SHDWC 0xfffffd10 +#define AT91SAM9RL_BASE_RTT 0xfffffd20 +#define AT91SAM9RL_BASE_PIT 0xfffffd30 +#define AT91SAM9RL_BASE_WDT 0xfffffd40 +#define AT91SAM9RL_BASE_RTC 0xfffffe00 #define AT91_USART0 AT91SAM9RL_BASE_US0 #define AT91_USART1 AT91SAM9RL_BASE_US1 diff --git a/arch/arm/mach-at91/include/mach/at91x40.h b/arch/arm/mach-at91/include/mach/at91x40.h index a152ff87e688..a57829f4fd18 100644 --- a/arch/arm/mach-at91/include/mach/at91x40.h +++ b/arch/arm/mach-at91/include/mach/at91x40.h @@ -40,7 +40,6 @@ #define AT91_PIOA (0xffff0000 - AT91_BASE_SYS) /* PIO Controller A */ #define AT91_PS (0xffff4000 - AT91_BASE_SYS) /* Power Save */ #define AT91_WD (0xffff8000 - AT91_BASE_SYS) /* Watchdog Timer */ -#define AT91_AIC (0xfffff000 - AT91_BASE_SYS) /* Advanced Interrupt Controller */ /* * The AT91x40 series doesn't have a debug unit like the other AT91 parts. diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h index eac92e995bb5..d0b377b21bd7 100644 --- a/arch/arm/mach-at91/include/mach/board.h +++ b/arch/arm/mach-at91/include/mach/board.h @@ -40,13 +40,14 @@ #include <linux/atmel-mci.h> #include <sound/atmel-ac97c.h> #include <linux/serial.h> +#include <linux/platform_data/macb.h> /* USB Device */ struct at91_udc_data { - u8 vbus_pin; /* high == host powering us */ + int vbus_pin; /* high == host powering us */ u8 vbus_active_low; /* vbus polarity */ u8 vbus_polled; /* Use polling, not interrupt */ - u8 pullup_pin; /* active == D+ pulled up */ + int pullup_pin; /* active == D+ pulled up */ u8 pullup_active_low; /* true == pullup_pin is active low */ }; extern void __init at91_add_device_udc(struct at91_udc_data *data); @@ -56,10 +57,10 @@ extern void __init at91_add_device_usba(struct usba_platform_data *data); /* Compact Flash */ struct at91_cf_data { - u8 irq_pin; /* I/O IRQ */ - u8 det_pin; /* Card detect */ - u8 vcc_pin; /* power switching */ - u8 rst_pin; /* card reset */ + int irq_pin; /* I/O IRQ */ + int det_pin; /* Card detect */ + int vcc_pin; /* power switching */ + int rst_pin; /* card reset */ u8 chipselect; /* EBI Chip Select number */ u8 flags; #define AT91_CF_TRUE_IDE 0x01 @@ -70,37 +71,26 @@ extern void __init at91_add_device_cf(struct at91_cf_data *data); /* MMC / SD */ /* at91_mci platform config */ struct at91_mmc_data { - u8 det_pin; /* card detect IRQ */ + int det_pin; /* card detect IRQ */ unsigned slot_b:1; /* uses Slot B */ unsigned wire4:1; /* (SD) supports DAT0..DAT3 */ - u8 wp_pin; /* (SD) writeprotect detect */ - u8 vcc_pin; /* power switching (high == on) */ + int wp_pin; /* (SD) writeprotect detect */ + int vcc_pin; /* power switching (high == on) */ }; extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data); /* atmel-mci platform config */ extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data); - /* Ethernet (EMAC & MACB) */ -struct at91_eth_data { - u32 phy_mask; - u8 phy_irq_pin; /* PHY IRQ */ - u8 is_rmii; /* using RMII interface? */ -}; -extern void __init at91_add_device_eth(struct at91_eth_data *data); - -#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \ - || defined(CONFIG_ARCH_AT91SAM9G45) -#define eth_platform_data at91_eth_data -#endif +extern void __init at91_add_device_eth(struct macb_platform_data *data); /* USB Host */ struct at91_usbh_data { u8 ports; /* number of ports on root hub */ - u8 vbus_pin[2]; /* port power-control pin */ + int vbus_pin[2]; /* port power-control pin */ u8 vbus_pin_inverted; u8 overcurrent_supported; - u8 overcurrent_pin[2]; + int overcurrent_pin[2]; u8 overcurrent_status[2]; u8 overcurrent_changed[2]; }; @@ -110,9 +100,9 @@ extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data); /* NAND / SmartMedia */ struct atmel_nand_data { - u8 enable_pin; /* chip enable */ - u8 det_pin; /* card detect */ - u8 rdy_pin; /* ready/busy */ + int enable_pin; /* chip enable */ + int det_pin; /* card detect */ + int rdy_pin; /* ready/busy */ u8 rdy_pin_active_low; /* rdy_pin value is inverted */ u8 ale; /* address line number connected to ALE */ u8 cle; /* address line number connected to CLE */ diff --git a/arch/arm/mach-at91/include/mach/debug-macro.S b/arch/arm/mach-at91/include/mach/debug-macro.S index 0ed8648c6452..c6bb9e2d9baa 100644 --- a/arch/arm/mach-at91/include/mach/debug-macro.S +++ b/arch/arm/mach-at91/include/mach/debug-macro.S @@ -14,9 +14,15 @@ #include <mach/hardware.h> #include <mach/at91_dbgu.h> +#if defined(CONFIG_AT91_DEBUG_LL_DBGU0) +#define AT91_DBGU AT91_BASE_DBGU0 +#else +#define AT91_DBGU AT91_BASE_DBGU1 +#endif + .macro addruart, rp, rv, tmp - ldr \rp, =(AT91_BASE_SYS + AT91_DBGU) @ System peripherals (phys address) - ldr \rv, =(AT91_VA_BASE_SYS + AT91_DBGU) @ System peripherals (virt address) + ldr \rp, =AT91_DBGU @ System peripherals (phys address) + ldr \rv, =AT91_IO_P2V(AT91_DBGU) @ System peripherals (virt address) .endm .macro senduart,rd,rx diff --git a/arch/arm/mach-at91/include/mach/entry-macro.S b/arch/arm/mach-at91/include/mach/entry-macro.S index 7ab68f972227..423eea0ed74c 100644 --- a/arch/arm/mach-at91/include/mach/entry-macro.S +++ b/arch/arm/mach-at91/include/mach/entry-macro.S @@ -17,16 +17,17 @@ .endm .macro get_irqnr_preamble, base, tmp - ldr \base, =(AT91_VA_BASE_SYS + AT91_AIC) @ base virtual address of AIC peripheral + ldr \base, =at91_aic_base @ base virtual address of AIC peripheral + ldr \base, [\base] .endm .macro arch_ret_to_user, tmp1, tmp2 .endm .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - ldr \irqnr, [\base, #(AT91_AIC_IVR - AT91_AIC)] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt) - ldr \irqstat, [\base, #(AT91_AIC_ISR - AT91_AIC)] @ read interrupt source number - teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt - streq \tmp, [\base, #(AT91_AIC_EOICR - AT91_AIC)] @ not going to be handled further, then ACK it now. + ldr \irqnr, [\base, #AT91_AIC_IVR] @ read IRQ vector register: de-asserts nIRQ to processor (and clears interrupt) + ldr \irqstat, [\base, #AT91_AIC_ISR] @ read interrupt source number + teq \irqstat, #0 @ ISR is 0 when no current interrupt, or spurious interrupt + streq \tmp, [\base, #AT91_AIC_EOICR] @ not going to be handled further, then ACK it now. .endm diff --git a/arch/arm/mach-at91/include/mach/gpio.h b/arch/arm/mach-at91/include/mach/gpio.h index 2b9a1f51210f..e3fd225121c7 100644 --- a/arch/arm/mach-at91/include/mach/gpio.h +++ b/arch/arm/mach-at91/include/mach/gpio.h @@ -16,177 +16,175 @@ #include <linux/kernel.h> #include <asm/irq.h> -#define PIN_BASE NR_AIC_IRQS - #define MAX_GPIO_BANKS 5 -#define NR_BUILTIN_GPIO (PIN_BASE + (MAX_GPIO_BANKS * 32)) +#define NR_BUILTIN_GPIO (MAX_GPIO_BANKS * 32) /* these pin numbers double as IRQ numbers, like AT91xxx_ID_* values */ -#define AT91_PIN_PA0 (PIN_BASE + 0x00 + 0) -#define AT91_PIN_PA1 (PIN_BASE + 0x00 + 1) -#define AT91_PIN_PA2 (PIN_BASE + 0x00 + 2) -#define AT91_PIN_PA3 (PIN_BASE + 0x00 + 3) -#define AT91_PIN_PA4 (PIN_BASE + 0x00 + 4) -#define AT91_PIN_PA5 (PIN_BASE + 0x00 + 5) -#define AT91_PIN_PA6 (PIN_BASE + 0x00 + 6) -#define AT91_PIN_PA7 (PIN_BASE + 0x00 + 7) -#define AT91_PIN_PA8 (PIN_BASE + 0x00 + 8) -#define AT91_PIN_PA9 (PIN_BASE + 0x00 + 9) -#define AT91_PIN_PA10 (PIN_BASE + 0x00 + 10) -#define AT91_PIN_PA11 (PIN_BASE + 0x00 + 11) -#define AT91_PIN_PA12 (PIN_BASE + 0x00 + 12) -#define AT91_PIN_PA13 (PIN_BASE + 0x00 + 13) -#define AT91_PIN_PA14 (PIN_BASE + 0x00 + 14) -#define AT91_PIN_PA15 (PIN_BASE + 0x00 + 15) -#define AT91_PIN_PA16 (PIN_BASE + 0x00 + 16) -#define AT91_PIN_PA17 (PIN_BASE + 0x00 + 17) -#define AT91_PIN_PA18 (PIN_BASE + 0x00 + 18) -#define AT91_PIN_PA19 (PIN_BASE + 0x00 + 19) -#define AT91_PIN_PA20 (PIN_BASE + 0x00 + 20) -#define AT91_PIN_PA21 (PIN_BASE + 0x00 + 21) -#define AT91_PIN_PA22 (PIN_BASE + 0x00 + 22) -#define AT91_PIN_PA23 (PIN_BASE + 0x00 + 23) -#define AT91_PIN_PA24 (PIN_BASE + 0x00 + 24) -#define AT91_PIN_PA25 (PIN_BASE + 0x00 + 25) -#define AT91_PIN_PA26 (PIN_BASE + 0x00 + 26) -#define AT91_PIN_PA27 (PIN_BASE + 0x00 + 27) -#define AT91_PIN_PA28 (PIN_BASE + 0x00 + 28) -#define AT91_PIN_PA29 (PIN_BASE + 0x00 + 29) -#define AT91_PIN_PA30 (PIN_BASE + 0x00 + 30) -#define AT91_PIN_PA31 (PIN_BASE + 0x00 + 31) - -#define AT91_PIN_PB0 (PIN_BASE + 0x20 + 0) -#define AT91_PIN_PB1 (PIN_BASE + 0x20 + 1) -#define AT91_PIN_PB2 (PIN_BASE + 0x20 + 2) -#define AT91_PIN_PB3 (PIN_BASE + 0x20 + 3) -#define AT91_PIN_PB4 (PIN_BASE + 0x20 + 4) -#define AT91_PIN_PB5 (PIN_BASE + 0x20 + 5) -#define AT91_PIN_PB6 (PIN_BASE + 0x20 + 6) -#define AT91_PIN_PB7 (PIN_BASE + 0x20 + 7) -#define AT91_PIN_PB8 (PIN_BASE + 0x20 + 8) -#define AT91_PIN_PB9 (PIN_BASE + 0x20 + 9) -#define AT91_PIN_PB10 (PIN_BASE + 0x20 + 10) -#define AT91_PIN_PB11 (PIN_BASE + 0x20 + 11) -#define AT91_PIN_PB12 (PIN_BASE + 0x20 + 12) -#define AT91_PIN_PB13 (PIN_BASE + 0x20 + 13) -#define AT91_PIN_PB14 (PIN_BASE + 0x20 + 14) -#define AT91_PIN_PB15 (PIN_BASE + 0x20 + 15) -#define AT91_PIN_PB16 (PIN_BASE + 0x20 + 16) -#define AT91_PIN_PB17 (PIN_BASE + 0x20 + 17) -#define AT91_PIN_PB18 (PIN_BASE + 0x20 + 18) -#define AT91_PIN_PB19 (PIN_BASE + 0x20 + 19) -#define AT91_PIN_PB20 (PIN_BASE + 0x20 + 20) -#define AT91_PIN_PB21 (PIN_BASE + 0x20 + 21) -#define AT91_PIN_PB22 (PIN_BASE + 0x20 + 22) -#define AT91_PIN_PB23 (PIN_BASE + 0x20 + 23) -#define AT91_PIN_PB24 (PIN_BASE + 0x20 + 24) -#define AT91_PIN_PB25 (PIN_BASE + 0x20 + 25) -#define AT91_PIN_PB26 (PIN_BASE + 0x20 + 26) -#define AT91_PIN_PB27 (PIN_BASE + 0x20 + 27) -#define AT91_PIN_PB28 (PIN_BASE + 0x20 + 28) -#define AT91_PIN_PB29 (PIN_BASE + 0x20 + 29) -#define AT91_PIN_PB30 (PIN_BASE + 0x20 + 30) -#define AT91_PIN_PB31 (PIN_BASE + 0x20 + 31) - -#define AT91_PIN_PC0 (PIN_BASE + 0x40 + 0) -#define AT91_PIN_PC1 (PIN_BASE + 0x40 + 1) -#define AT91_PIN_PC2 (PIN_BASE + 0x40 + 2) -#define AT91_PIN_PC3 (PIN_BASE + 0x40 + 3) -#define AT91_PIN_PC4 (PIN_BASE + 0x40 + 4) -#define AT91_PIN_PC5 (PIN_BASE + 0x40 + 5) -#define AT91_PIN_PC6 (PIN_BASE + 0x40 + 6) -#define AT91_PIN_PC7 (PIN_BASE + 0x40 + 7) -#define AT91_PIN_PC8 (PIN_BASE + 0x40 + 8) -#define AT91_PIN_PC9 (PIN_BASE + 0x40 + 9) -#define AT91_PIN_PC10 (PIN_BASE + 0x40 + 10) -#define AT91_PIN_PC11 (PIN_BASE + 0x40 + 11) -#define AT91_PIN_PC12 (PIN_BASE + 0x40 + 12) -#define AT91_PIN_PC13 (PIN_BASE + 0x40 + 13) -#define AT91_PIN_PC14 (PIN_BASE + 0x40 + 14) -#define AT91_PIN_PC15 (PIN_BASE + 0x40 + 15) -#define AT91_PIN_PC16 (PIN_BASE + 0x40 + 16) -#define AT91_PIN_PC17 (PIN_BASE + 0x40 + 17) -#define AT91_PIN_PC18 (PIN_BASE + 0x40 + 18) -#define AT91_PIN_PC19 (PIN_BASE + 0x40 + 19) -#define AT91_PIN_PC20 (PIN_BASE + 0x40 + 20) -#define AT91_PIN_PC21 (PIN_BASE + 0x40 + 21) -#define AT91_PIN_PC22 (PIN_BASE + 0x40 + 22) -#define AT91_PIN_PC23 (PIN_BASE + 0x40 + 23) -#define AT91_PIN_PC24 (PIN_BASE + 0x40 + 24) -#define AT91_PIN_PC25 (PIN_BASE + 0x40 + 25) -#define AT91_PIN_PC26 (PIN_BASE + 0x40 + 26) -#define AT91_PIN_PC27 (PIN_BASE + 0x40 + 27) -#define AT91_PIN_PC28 (PIN_BASE + 0x40 + 28) -#define AT91_PIN_PC29 (PIN_BASE + 0x40 + 29) -#define AT91_PIN_PC30 (PIN_BASE + 0x40 + 30) -#define AT91_PIN_PC31 (PIN_BASE + 0x40 + 31) - -#define AT91_PIN_PD0 (PIN_BASE + 0x60 + 0) -#define AT91_PIN_PD1 (PIN_BASE + 0x60 + 1) -#define AT91_PIN_PD2 (PIN_BASE + 0x60 + 2) -#define AT91_PIN_PD3 (PIN_BASE + 0x60 + 3) -#define AT91_PIN_PD4 (PIN_BASE + 0x60 + 4) -#define AT91_PIN_PD5 (PIN_BASE + 0x60 + 5) -#define AT91_PIN_PD6 (PIN_BASE + 0x60 + 6) -#define AT91_PIN_PD7 (PIN_BASE + 0x60 + 7) -#define AT91_PIN_PD8 (PIN_BASE + 0x60 + 8) -#define AT91_PIN_PD9 (PIN_BASE + 0x60 + 9) -#define AT91_PIN_PD10 (PIN_BASE + 0x60 + 10) -#define AT91_PIN_PD11 (PIN_BASE + 0x60 + 11) -#define AT91_PIN_PD12 (PIN_BASE + 0x60 + 12) -#define AT91_PIN_PD13 (PIN_BASE + 0x60 + 13) -#define AT91_PIN_PD14 (PIN_BASE + 0x60 + 14) -#define AT91_PIN_PD15 (PIN_BASE + 0x60 + 15) -#define AT91_PIN_PD16 (PIN_BASE + 0x60 + 16) -#define AT91_PIN_PD17 (PIN_BASE + 0x60 + 17) -#define AT91_PIN_PD18 (PIN_BASE + 0x60 + 18) -#define AT91_PIN_PD19 (PIN_BASE + 0x60 + 19) -#define AT91_PIN_PD20 (PIN_BASE + 0x60 + 20) -#define AT91_PIN_PD21 (PIN_BASE + 0x60 + 21) -#define AT91_PIN_PD22 (PIN_BASE + 0x60 + 22) -#define AT91_PIN_PD23 (PIN_BASE + 0x60 + 23) -#define AT91_PIN_PD24 (PIN_BASE + 0x60 + 24) -#define AT91_PIN_PD25 (PIN_BASE + 0x60 + 25) -#define AT91_PIN_PD26 (PIN_BASE + 0x60 + 26) -#define AT91_PIN_PD27 (PIN_BASE + 0x60 + 27) -#define AT91_PIN_PD28 (PIN_BASE + 0x60 + 28) -#define AT91_PIN_PD29 (PIN_BASE + 0x60 + 29) -#define AT91_PIN_PD30 (PIN_BASE + 0x60 + 30) -#define AT91_PIN_PD31 (PIN_BASE + 0x60 + 31) - -#define AT91_PIN_PE0 (PIN_BASE + 0x80 + 0) -#define AT91_PIN_PE1 (PIN_BASE + 0x80 + 1) -#define AT91_PIN_PE2 (PIN_BASE + 0x80 + 2) -#define AT91_PIN_PE3 (PIN_BASE + 0x80 + 3) -#define AT91_PIN_PE4 (PIN_BASE + 0x80 + 4) -#define AT91_PIN_PE5 (PIN_BASE + 0x80 + 5) -#define AT91_PIN_PE6 (PIN_BASE + 0x80 + 6) -#define AT91_PIN_PE7 (PIN_BASE + 0x80 + 7) -#define AT91_PIN_PE8 (PIN_BASE + 0x80 + 8) -#define AT91_PIN_PE9 (PIN_BASE + 0x80 + 9) -#define AT91_PIN_PE10 (PIN_BASE + 0x80 + 10) -#define AT91_PIN_PE11 (PIN_BASE + 0x80 + 11) -#define AT91_PIN_PE12 (PIN_BASE + 0x80 + 12) -#define AT91_PIN_PE13 (PIN_BASE + 0x80 + 13) -#define AT91_PIN_PE14 (PIN_BASE + 0x80 + 14) -#define AT91_PIN_PE15 (PIN_BASE + 0x80 + 15) -#define AT91_PIN_PE16 (PIN_BASE + 0x80 + 16) -#define AT91_PIN_PE17 (PIN_BASE + 0x80 + 17) -#define AT91_PIN_PE18 (PIN_BASE + 0x80 + 18) -#define AT91_PIN_PE19 (PIN_BASE + 0x80 + 19) -#define AT91_PIN_PE20 (PIN_BASE + 0x80 + 20) -#define AT91_PIN_PE21 (PIN_BASE + 0x80 + 21) -#define AT91_PIN_PE22 (PIN_BASE + 0x80 + 22) -#define AT91_PIN_PE23 (PIN_BASE + 0x80 + 23) -#define AT91_PIN_PE24 (PIN_BASE + 0x80 + 24) -#define AT91_PIN_PE25 (PIN_BASE + 0x80 + 25) -#define AT91_PIN_PE26 (PIN_BASE + 0x80 + 26) -#define AT91_PIN_PE27 (PIN_BASE + 0x80 + 27) -#define AT91_PIN_PE28 (PIN_BASE + 0x80 + 28) -#define AT91_PIN_PE29 (PIN_BASE + 0x80 + 29) -#define AT91_PIN_PE30 (PIN_BASE + 0x80 + 30) -#define AT91_PIN_PE31 (PIN_BASE + 0x80 + 31) +#define AT91_PIN_PA0 (0x00 + 0) +#define AT91_PIN_PA1 (0x00 + 1) +#define AT91_PIN_PA2 (0x00 + 2) +#define AT91_PIN_PA3 (0x00 + 3) +#define AT91_PIN_PA4 (0x00 + 4) +#define AT91_PIN_PA5 (0x00 + 5) +#define AT91_PIN_PA6 (0x00 + 6) +#define AT91_PIN_PA7 (0x00 + 7) +#define AT91_PIN_PA8 (0x00 + 8) +#define AT91_PIN_PA9 (0x00 + 9) +#define AT91_PIN_PA10 (0x00 + 10) +#define AT91_PIN_PA11 (0x00 + 11) +#define AT91_PIN_PA12 (0x00 + 12) +#define AT91_PIN_PA13 (0x00 + 13) +#define AT91_PIN_PA14 (0x00 + 14) +#define AT91_PIN_PA15 (0x00 + 15) +#define AT91_PIN_PA16 (0x00 + 16) +#define AT91_PIN_PA17 (0x00 + 17) +#define AT91_PIN_PA18 (0x00 + 18) +#define AT91_PIN_PA19 (0x00 + 19) +#define AT91_PIN_PA20 (0x00 + 20) +#define AT91_PIN_PA21 (0x00 + 21) +#define AT91_PIN_PA22 (0x00 + 22) +#define AT91_PIN_PA23 (0x00 + 23) +#define AT91_PIN_PA24 (0x00 + 24) +#define AT91_PIN_PA25 (0x00 + 25) +#define AT91_PIN_PA26 (0x00 + 26) +#define AT91_PIN_PA27 (0x00 + 27) +#define AT91_PIN_PA28 (0x00 + 28) +#define AT91_PIN_PA29 (0x00 + 29) +#define AT91_PIN_PA30 (0x00 + 30) +#define AT91_PIN_PA31 (0x00 + 31) + +#define AT91_PIN_PB0 (0x20 + 0) +#define AT91_PIN_PB1 (0x20 + 1) +#define AT91_PIN_PB2 (0x20 + 2) +#define AT91_PIN_PB3 (0x20 + 3) +#define AT91_PIN_PB4 (0x20 + 4) +#define AT91_PIN_PB5 (0x20 + 5) +#define AT91_PIN_PB6 (0x20 + 6) +#define AT91_PIN_PB7 (0x20 + 7) +#define AT91_PIN_PB8 (0x20 + 8) +#define AT91_PIN_PB9 (0x20 + 9) +#define AT91_PIN_PB10 (0x20 + 10) +#define AT91_PIN_PB11 (0x20 + 11) +#define AT91_PIN_PB12 (0x20 + 12) +#define AT91_PIN_PB13 (0x20 + 13) +#define AT91_PIN_PB14 (0x20 + 14) +#define AT91_PIN_PB15 (0x20 + 15) +#define AT91_PIN_PB16 (0x20 + 16) +#define AT91_PIN_PB17 (0x20 + 17) +#define AT91_PIN_PB18 (0x20 + 18) +#define AT91_PIN_PB19 (0x20 + 19) +#define AT91_PIN_PB20 (0x20 + 20) +#define AT91_PIN_PB21 (0x20 + 21) +#define AT91_PIN_PB22 (0x20 + 22) +#define AT91_PIN_PB23 (0x20 + 23) +#define AT91_PIN_PB24 (0x20 + 24) +#define AT91_PIN_PB25 (0x20 + 25) +#define AT91_PIN_PB26 (0x20 + 26) +#define AT91_PIN_PB27 (0x20 + 27) +#define AT91_PIN_PB28 (0x20 + 28) +#define AT91_PIN_PB29 (0x20 + 29) +#define AT91_PIN_PB30 (0x20 + 30) +#define AT91_PIN_PB31 (0x20 + 31) + +#define AT91_PIN_PC0 (0x40 + 0) +#define AT91_PIN_PC1 (0x40 + 1) +#define AT91_PIN_PC2 (0x40 + 2) +#define AT91_PIN_PC3 (0x40 + 3) +#define AT91_PIN_PC4 (0x40 + 4) +#define AT91_PIN_PC5 (0x40 + 5) +#define AT91_PIN_PC6 (0x40 + 6) +#define AT91_PIN_PC7 (0x40 + 7) +#define AT91_PIN_PC8 (0x40 + 8) +#define AT91_PIN_PC9 (0x40 + 9) +#define AT91_PIN_PC10 (0x40 + 10) +#define AT91_PIN_PC11 (0x40 + 11) +#define AT91_PIN_PC12 (0x40 + 12) +#define AT91_PIN_PC13 (0x40 + 13) +#define AT91_PIN_PC14 (0x40 + 14) +#define AT91_PIN_PC15 (0x40 + 15) +#define AT91_PIN_PC16 (0x40 + 16) +#define AT91_PIN_PC17 (0x40 + 17) +#define AT91_PIN_PC18 (0x40 + 18) +#define AT91_PIN_PC19 (0x40 + 19) +#define AT91_PIN_PC20 (0x40 + 20) +#define AT91_PIN_PC21 (0x40 + 21) +#define AT91_PIN_PC22 (0x40 + 22) +#define AT91_PIN_PC23 (0x40 + 23) +#define AT91_PIN_PC24 (0x40 + 24) +#define AT91_PIN_PC25 (0x40 + 25) +#define AT91_PIN_PC26 (0x40 + 26) +#define AT91_PIN_PC27 (0x40 + 27) +#define AT91_PIN_PC28 (0x40 + 28) +#define AT91_PIN_PC29 (0x40 + 29) +#define AT91_PIN_PC30 (0x40 + 30) +#define AT91_PIN_PC31 (0x40 + 31) + +#define AT91_PIN_PD0 (0x60 + 0) +#define AT91_PIN_PD1 (0x60 + 1) +#define AT91_PIN_PD2 (0x60 + 2) +#define AT91_PIN_PD3 (0x60 + 3) +#define AT91_PIN_PD4 (0x60 + 4) +#define AT91_PIN_PD5 (0x60 + 5) +#define AT91_PIN_PD6 (0x60 + 6) +#define AT91_PIN_PD7 (0x60 + 7) +#define AT91_PIN_PD8 (0x60 + 8) +#define AT91_PIN_PD9 (0x60 + 9) +#define AT91_PIN_PD10 (0x60 + 10) +#define AT91_PIN_PD11 (0x60 + 11) +#define AT91_PIN_PD12 (0x60 + 12) +#define AT91_PIN_PD13 (0x60 + 13) +#define AT91_PIN_PD14 (0x60 + 14) +#define AT91_PIN_PD15 (0x60 + 15) +#define AT91_PIN_PD16 (0x60 + 16) +#define AT91_PIN_PD17 (0x60 + 17) +#define AT91_PIN_PD18 (0x60 + 18) +#define AT91_PIN_PD19 (0x60 + 19) +#define AT91_PIN_PD20 (0x60 + 20) +#define AT91_PIN_PD21 (0x60 + 21) +#define AT91_PIN_PD22 (0x60 + 22) +#define AT91_PIN_PD23 (0x60 + 23) +#define AT91_PIN_PD24 (0x60 + 24) +#define AT91_PIN_PD25 (0x60 + 25) +#define AT91_PIN_PD26 (0x60 + 26) +#define AT91_PIN_PD27 (0x60 + 27) +#define AT91_PIN_PD28 (0x60 + 28) +#define AT91_PIN_PD29 (0x60 + 29) +#define AT91_PIN_PD30 (0x60 + 30) +#define AT91_PIN_PD31 (0x60 + 31) + +#define AT91_PIN_PE0 (0x80 + 0) +#define AT91_PIN_PE1 (0x80 + 1) +#define AT91_PIN_PE2 (0x80 + 2) +#define AT91_PIN_PE3 (0x80 + 3) +#define AT91_PIN_PE4 (0x80 + 4) +#define AT91_PIN_PE5 (0x80 + 5) +#define AT91_PIN_PE6 (0x80 + 6) +#define AT91_PIN_PE7 (0x80 + 7) +#define AT91_PIN_PE8 (0x80 + 8) +#define AT91_PIN_PE9 (0x80 + 9) +#define AT91_PIN_PE10 (0x80 + 10) +#define AT91_PIN_PE11 (0x80 + 11) +#define AT91_PIN_PE12 (0x80 + 12) +#define AT91_PIN_PE13 (0x80 + 13) +#define AT91_PIN_PE14 (0x80 + 14) +#define AT91_PIN_PE15 (0x80 + 15) +#define AT91_PIN_PE16 (0x80 + 16) +#define AT91_PIN_PE17 (0x80 + 17) +#define AT91_PIN_PE18 (0x80 + 18) +#define AT91_PIN_PE19 (0x80 + 19) +#define AT91_PIN_PE20 (0x80 + 20) +#define AT91_PIN_PE21 (0x80 + 21) +#define AT91_PIN_PE22 (0x80 + 22) +#define AT91_PIN_PE23 (0x80 + 23) +#define AT91_PIN_PE24 (0x80 + 24) +#define AT91_PIN_PE25 (0x80 + 25) +#define AT91_PIN_PE26 (0x80 + 26) +#define AT91_PIN_PE27 (0x80 + 27) +#define AT91_PIN_PE28 (0x80 + 28) +#define AT91_PIN_PE29 (0x80 + 29) +#define AT91_PIN_PE30 (0x80 + 30) +#define AT91_PIN_PE31 (0x80 + 31) #ifndef __ASSEMBLY__ /* setup setup routines, called from board init or driver probe() */ @@ -215,8 +213,8 @@ extern void at91_gpio_resume(void); #include <asm/errno.h> -#define gpio_to_irq(gpio) (gpio) -#define irq_to_gpio(irq) (irq) +#define gpio_to_irq(gpio) (gpio + NR_AIC_IRQS) +#define irq_to_gpio(irq) (irq - NR_AIC_IRQS) #endif /* __ASSEMBLY__ */ diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h index 483478d8be6b..2d0e4e998566 100644 --- a/arch/arm/mach-at91/include/mach/hardware.h +++ b/arch/arm/mach-at91/include/mach/hardware.h @@ -16,6 +16,12 @@ #include <asm/sizes.h> +/* DBGU base */ +/* rm9200, 9260/9g20, 9261/9g10, 9rl */ +#define AT91_BASE_DBGU0 0xfffff200 +/* 9263, 9g45, cap9 */ +#define AT91_BASE_DBGU1 0xffffee00 + #if defined(CONFIG_ARCH_AT91RM9200) #include <mach/at91rm9200.h> #elif defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9G20) @@ -52,6 +58,12 @@ #endif /* + * On all at91 have the Advanced Interrupt Controller starts at address + * 0xfffff000 + */ +#define AT91_AIC 0xfffff000 + +/* * Peripheral identifiers/interrupts. */ #define AT91_ID_FIQ 0 /* Advanced Interrupt Controller (FIQ) */ diff --git a/arch/arm/mach-at91/include/mach/irqs.h b/arch/arm/mach-at91/include/mach/irqs.h index 36bd55f3fc6e..ac8b7dfc85ef 100644 --- a/arch/arm/mach-at91/include/mach/irqs.h +++ b/arch/arm/mach-at91/include/mach/irqs.h @@ -31,7 +31,7 @@ * Acknowledge interrupt with AIC after interrupt has been handled. * (by kernel/irq.c) */ -#define irq_finish(irq) do { at91_sys_write(AT91_AIC_EOICR, 0); } while (0) +#define irq_finish(irq) do { at91_aic_write(AT91_AIC_EOICR, 0); } while (0) /* diff --git a/arch/arm/mach-at91/include/mach/system_rev.h b/arch/arm/mach-at91/include/mach/system_rev.h index 8f4866045b41..ec164a4124c9 100644 --- a/arch/arm/mach-at91/include/mach/system_rev.h +++ b/arch/arm/mach-at91/include/mach/system_rev.h @@ -19,7 +19,7 @@ #define BOARD_HAVE_NAND_16BIT (1 << 31) static inline int board_have_nand_16bit(void) { - return system_rev & BOARD_HAVE_NAND_16BIT; + return (system_rev & BOARD_HAVE_NAND_16BIT) ? 1 : 0; } #endif /* __ARCH_SYSTEM_REV_H__ */ diff --git a/arch/arm/mach-at91/include/mach/timex.h b/arch/arm/mach-at91/include/mach/timex.h index 85820ad801cc..5e917a66edd7 100644 --- a/arch/arm/mach-at91/include/mach/timex.h +++ b/arch/arm/mach-at91/include/mach/timex.h @@ -23,70 +23,15 @@ #include <mach/hardware.h> -#if defined(CONFIG_ARCH_AT91RM9200) +#ifdef CONFIG_ARCH_AT91X40 -#define CLOCK_TICK_RATE (AT91_SLOW_CLOCK) - -#elif defined(CONFIG_ARCH_AT91SAM9260) - -#if defined(CONFIG_MACH_USB_A9260) || defined(CONFIG_MACH_QIL_A9260) -#define AT91SAM9_MASTER_CLOCK 90000000 -#else -#define AT91SAM9_MASTER_CLOCK 99300000 -#endif - -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91SAM9261) - -#define AT91SAM9_MASTER_CLOCK 99300000 -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91SAM9G10) - -#define AT91SAM9_MASTER_CLOCK 133000000 -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91SAM9263) - -#if defined(CONFIG_MACH_USB_A9263) -#define AT91SAM9_MASTER_CLOCK 90000000 -#else -#define AT91SAM9_MASTER_CLOCK 99959500 -#endif - -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91SAM9RL) - -#define AT91SAM9_MASTER_CLOCK 100000000 -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91SAM9G20) +#define AT91X40_MASTER_CLOCK 40000000 +#define CLOCK_TICK_RATE (AT91X40_MASTER_CLOCK) -#if defined(CONFIG_MACH_USB_A9G20) -#define AT91SAM9_MASTER_CLOCK 133000000 #else -#define AT91SAM9_MASTER_CLOCK 132096000 -#endif - -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91SAM9G45) -#define AT91SAM9_MASTER_CLOCK 133333333 -#define CLOCK_TICK_RATE (AT91SAM9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91CAP9) - -#define AT91CAP9_MASTER_CLOCK 100000000 -#define CLOCK_TICK_RATE (AT91CAP9_MASTER_CLOCK/16) - -#elif defined(CONFIG_ARCH_AT91X40) - -#define AT91X40_MASTER_CLOCK 40000000 -#define CLOCK_TICK_RATE (AT91X40_MASTER_CLOCK) +#define CLOCK_TICK_RATE 12345678 #endif -#endif +#endif /* __ASM_ARCH_TIMEX_H */ diff --git a/arch/arm/mach-at91/include/mach/uncompress.h b/arch/arm/mach-at91/include/mach/uncompress.h index 18bdcdeb474f..0234fd9d20d6 100644 --- a/arch/arm/mach-at91/include/mach/uncompress.h +++ b/arch/arm/mach-at91/include/mach/uncompress.h @@ -24,8 +24,10 @@ #include <linux/io.h> #include <linux/atmel_serial.h> -#if defined(CONFIG_AT91_EARLY_DBGU) -#define UART_OFFSET (AT91_DBGU + AT91_BASE_SYS) +#if defined(CONFIG_AT91_EARLY_DBGU0) +#define UART_OFFSET AT91_BASE_DBGU0 +#elif defined(CONFIG_AT91_EARLY_DBGU1) +#define UART_OFFSET AT91_BASE_DBGU1 #elif defined(CONFIG_AT91_EARLY_USART0) #define UART_OFFSET AT91_USART0 #elif defined(CONFIG_AT91_EARLY_USART1) diff --git a/arch/arm/mach-at91/irq.c b/arch/arm/mach-at91/irq.c index 9665265ec757..be6b639ecd7b 100644 --- a/arch/arm/mach-at91/irq.c +++ b/arch/arm/mach-at91/irq.c @@ -33,17 +33,18 @@ #include <asm/mach/irq.h> #include <asm/mach/map.h> +void __iomem *at91_aic_base; static void at91_aic_mask_irq(struct irq_data *d) { /* Disable interrupt on AIC */ - at91_sys_write(AT91_AIC_IDCR, 1 << d->irq); + at91_aic_write(AT91_AIC_IDCR, 1 << d->irq); } static void at91_aic_unmask_irq(struct irq_data *d) { /* Enable interrupt on AIC */ - at91_sys_write(AT91_AIC_IECR, 1 << d->irq); + at91_aic_write(AT91_AIC_IECR, 1 << d->irq); } unsigned int at91_extern_irq; @@ -77,8 +78,8 @@ static int at91_aic_set_type(struct irq_data *d, unsigned type) return -EINVAL; } - smr = at91_sys_read(AT91_AIC_SMR(d->irq)) & ~AT91_AIC_SRCTYPE; - at91_sys_write(AT91_AIC_SMR(d->irq), smr | srctype); + smr = at91_aic_read(AT91_AIC_SMR(d->irq)) & ~AT91_AIC_SRCTYPE; + at91_aic_write(AT91_AIC_SMR(d->irq), smr | srctype); return 0; } @@ -102,15 +103,15 @@ static int at91_aic_set_wake(struct irq_data *d, unsigned value) void at91_irq_suspend(void) { - backups = at91_sys_read(AT91_AIC_IMR); - at91_sys_write(AT91_AIC_IDCR, backups); - at91_sys_write(AT91_AIC_IECR, wakeups); + backups = at91_aic_read(AT91_AIC_IMR); + at91_aic_write(AT91_AIC_IDCR, backups); + at91_aic_write(AT91_AIC_IECR, wakeups); } void at91_irq_resume(void) { - at91_sys_write(AT91_AIC_IDCR, wakeups); - at91_sys_write(AT91_AIC_IECR, backups); + at91_aic_write(AT91_AIC_IDCR, wakeups); + at91_aic_write(AT91_AIC_IECR, backups); } #else @@ -133,34 +134,39 @@ void __init at91_aic_init(unsigned int priority[NR_AIC_IRQS]) { unsigned int i; + at91_aic_base = ioremap(AT91_AIC, 512); + + if (!at91_aic_base) + panic("Impossible to ioremap AT91_AIC\n"); + /* * The IVR is used by macro get_irqnr_and_base to read and verify. * The irq number is NR_AIC_IRQS when a spurious interrupt has occurred. */ for (i = 0; i < NR_AIC_IRQS; i++) { /* Put irq number in Source Vector Register: */ - at91_sys_write(AT91_AIC_SVR(i), i); + at91_aic_write(AT91_AIC_SVR(i), i); /* Active Low interrupt, with the specified priority */ - at91_sys_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]); + at91_aic_write(AT91_AIC_SMR(i), AT91_AIC_SRCTYPE_LOW | priority[i]); irq_set_chip_and_handler(i, &at91_aic_chip, handle_level_irq); set_irq_flags(i, IRQF_VALID | IRQF_PROBE); /* Perform 8 End Of Interrupt Command to make sure AIC will not Lock out nIRQ */ if (i < 8) - at91_sys_write(AT91_AIC_EOICR, 0); + at91_aic_write(AT91_AIC_EOICR, 0); } /* * Spurious Interrupt ID in Spurious Vector Register is NR_AIC_IRQS * When there is no current interrupt, the IRQ Vector Register reads the value stored in AIC_SPU */ - at91_sys_write(AT91_AIC_SPU, NR_AIC_IRQS); + at91_aic_write(AT91_AIC_SPU, NR_AIC_IRQS); /* No debugging in AIC: Debug (Protect) Control Register */ - at91_sys_write(AT91_AIC_DCR, 0); + at91_aic_write(AT91_AIC_DCR, 0); /* Disable and clear all interrupts initially */ - at91_sys_write(AT91_AIC_IDCR, 0xFFFFFFFF); - at91_sys_write(AT91_AIC_ICCR, 0xFFFFFFFF); + at91_aic_write(AT91_AIC_IDCR, 0xFFFFFFFF); + at91_aic_write(AT91_AIC_ICCR, 0xFFFFFFFF); } diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index 7046158109d7..62ad95556c36 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -34,7 +34,7 @@ /* * Show the reason for the previous system reset. */ -#if defined(AT91_SHDWC) +#if defined(AT91_RSTC) #include <mach/at91_rstc.h> #include <mach/at91_shdwc.h> @@ -58,8 +58,11 @@ static void __init show_reset_status(void) char *reason, *r2 = reset; u32 reset_type, wake_type; + if (!at91_shdwc_base) + return; + reset_type = at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_RSTTYP; - wake_type = at91_sys_read(AT91_SHDW_SR); + wake_type = at91_shdwc_read(AT91_SHDW_SR); switch (reset_type) { case AT91_RSTC_RSTTYP_GENERAL: @@ -215,7 +218,7 @@ static int at91_pm_enter(suspend_state_t state) | (1 << AT91_ID_FIQ) | (1 << AT91_ID_SYS) | (at91_extern_irq)) - & at91_sys_read(AT91_AIC_IMR), + & at91_aic_read(AT91_AIC_IMR), state); switch (state) { @@ -283,7 +286,7 @@ static int at91_pm_enter(suspend_state_t state) } pr_debug("AT91: PM - wakeup %08x\n", - at91_sys_read(AT91_AIC_IPR) & at91_sys_read(AT91_AIC_IMR)); + at91_aic_read(AT91_AIC_IPR) & at91_aic_read(AT91_AIC_IMR)); error: target_state = PM_SUSPEND_ON; diff --git a/arch/arm/mach-at91/sam9_smc.c b/arch/arm/mach-at91/sam9_smc.c index 5eab6aa621d0..8294783b679d 100644 --- a/arch/arm/mach-at91/sam9_smc.c +++ b/arch/arm/mach-at91/sam9_smc.c @@ -10,38 +10,58 @@ #include <linux/module.h> #include <linux/io.h> +#include <linux/of.h> +#include <linux/of_address.h> #include <mach/at91sam9_smc.h> #include "sam9_smc.h" -void __init sam9_smc_configure(int cs, struct sam9_smc_config* config) + +#define AT91_SMC_CS(id, n) (smc_base_addr[id] + ((n) * 0x10)) + +static void __iomem *smc_base_addr[2]; + +static void __init sam9_smc_cs_configure(void __iomem *base, struct sam9_smc_config* config) { + /* Setup register */ - at91_sys_write(AT91_SMC_SETUP(cs), - AT91_SMC_NWESETUP_(config->nwe_setup) - | AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup) - | AT91_SMC_NRDSETUP_(config->nrd_setup) - | AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup) - ); + __raw_writel(AT91_SMC_NWESETUP_(config->nwe_setup) + | AT91_SMC_NCS_WRSETUP_(config->ncs_write_setup) + | AT91_SMC_NRDSETUP_(config->nrd_setup) + | AT91_SMC_NCS_RDSETUP_(config->ncs_read_setup), + base + AT91_SMC_SETUP); /* Pulse register */ - at91_sys_write(AT91_SMC_PULSE(cs), - AT91_SMC_NWEPULSE_(config->nwe_pulse) - | AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse) - | AT91_SMC_NRDPULSE_(config->nrd_pulse) - | AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse) - ); + __raw_writel(AT91_SMC_NWEPULSE_(config->nwe_pulse) + | AT91_SMC_NCS_WRPULSE_(config->ncs_write_pulse) + | AT91_SMC_NRDPULSE_(config->nrd_pulse) + | AT91_SMC_NCS_RDPULSE_(config->ncs_read_pulse), + base + AT91_SMC_PULSE); /* Cycle register */ - at91_sys_write(AT91_SMC_CYCLE(cs), - AT91_SMC_NWECYCLE_(config->write_cycle) - | AT91_SMC_NRDCYCLE_(config->read_cycle) - ); + __raw_writel(AT91_SMC_NWECYCLE_(config->write_cycle) + | AT91_SMC_NRDCYCLE_(config->read_cycle), + base + AT91_SMC_CYCLE); /* Mode register */ - at91_sys_write(AT91_SMC_MODE(cs), - config->mode - | AT91_SMC_TDF_(config->tdf_cycles) - ); + __raw_writel(config->mode + | AT91_SMC_TDF_(config->tdf_cycles), + base + AT91_SMC_MODE); +} + +void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config) +{ + sam9_smc_cs_configure(AT91_SMC_CS(id, cs), config); +} + +void __init at91sam9_ioremap_smc(int id, u32 addr) +{ + if (id > 1) { + pr_warn("%s: id > 2\n", __func__); + return; + } + smc_base_addr[id] = ioremap(addr, 512); + if (!smc_base_addr[id]) + pr_warn("Impossible to ioremap smc.%d 0x%x\n", id, addr); } diff --git a/arch/arm/mach-at91/sam9_smc.h b/arch/arm/mach-at91/sam9_smc.h index bf72cfb3455b..039c5ce17aec 100644 --- a/arch/arm/mach-at91/sam9_smc.h +++ b/arch/arm/mach-at91/sam9_smc.h @@ -30,4 +30,5 @@ struct sam9_smc_config { u8 tdf_cycles:4; }; -extern void __init sam9_smc_configure(int cs, struct sam9_smc_config* config); +extern void __init sam9_smc_configure(int id, int cs, struct sam9_smc_config* config); +extern void __init at91sam9_ioremap_smc(int id, u32 addr); diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c index aa64294c7db3..242c26b2368d 100644 --- a/arch/arm/mach-at91/setup.c +++ b/arch/arm/mach-at91/setup.c @@ -8,6 +8,7 @@ #include <linux/module.h> #include <linux/io.h> #include <linux/mm.h> +#include <linux/pm.h> #include <asm/mach/map.h> @@ -15,6 +16,7 @@ #include <mach/cpu.h> #include <mach/at91_dbgu.h> #include <mach/at91_pmc.h> +#include <mach/at91_shdwc.h> #include "soc.h" #include "generic.h" @@ -91,9 +93,6 @@ void at91_iounmap(volatile void __iomem *addr) } EXPORT_SYMBOL(at91_iounmap); -#define AT91_DBGU0 0xfffff200 -#define AT91_DBGU1 0xffffee00 - static void __init soc_detect(u32 dbgu_base) { u32 cidr, socid; @@ -266,9 +265,9 @@ void __init at91_map_io(void) at91_soc_initdata.type = AT91_SOC_NONE; at91_soc_initdata.subtype = AT91_SOC_SUBTYPE_NONE; - soc_detect(AT91_DBGU0); + soc_detect(AT91_BASE_DBGU0); if (!at91_soc_is_detected()) - soc_detect(AT91_DBGU1); + soc_detect(AT91_BASE_DBGU1); if (!at91_soc_is_detected()) panic("AT91: Impossible to detect the SOC type"); @@ -285,8 +284,25 @@ void __init at91_map_io(void) at91_boot_soc.map_io(); } +void __iomem *at91_shdwc_base = NULL; + +static void at91sam9_poweroff(void) +{ + at91_shdwc_write(AT91_SHDW_CR, AT91_SHDW_KEY | AT91_SHDW_SHDW); +} + +void __init at91_ioremap_shdwc(u32 base_addr) +{ + at91_shdwc_base = ioremap(base_addr, 16); + if (!at91_shdwc_base) + panic("Impossible to ioremap at91_shdwc_base\n"); + pm_power_off = at91sam9_poweroff; +} + void __init at91_initialize(unsigned long main_clock) { + at91_boot_soc.ioremap_registers(); + /* Init clock subsystem */ at91_clock_init(main_clock); diff --git a/arch/arm/mach-at91/soc.h b/arch/arm/mach-at91/soc.h index 21ed8816e6f7..4588ae6f7acd 100644 --- a/arch/arm/mach-at91/soc.h +++ b/arch/arm/mach-at91/soc.h @@ -7,6 +7,7 @@ struct at91_init_soc { unsigned int *default_irq_priority; void (*map_io)(void); + void (*ioremap_registers)(void); void (*register_clocks)(void); void (*init)(void); }; diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 1d7d24995226..6659a90dbcad 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -753,7 +753,7 @@ static struct snd_platform_data da850_evm_snd_data = { .num_serializer = ARRAY_SIZE(da850_iis_serializer_direction), .tdm_slots = 2, .serial_dir = da850_iis_serializer_direction, - .asp_chan_q = EVENTQ_1, + .asp_chan_q = EVENTQ_0, .version = MCASP_VERSION_2, .txnumevt = 1, .rxnumevt = 1, diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index 1918ae711428..46e1f4173b97 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -107,7 +107,7 @@ static struct mtd_partition davinci_nand_partitions[] = { /* UBL (a few copies) plus U-Boot */ .name = "bootloader", .offset = 0, - .size = 28 * NAND_BLOCK_SIZE, + .size = 30 * NAND_BLOCK_SIZE, .mask_flags = MTD_WRITEABLE, /* force read-only */ }, { /* U-Boot environment */ diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index e574d7f837a8..635bf7740157 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -564,7 +564,7 @@ static int setup_vpif_input_channel_mode(int mux_mode) int val; u32 value; - if (!vpif_vsclkdis_reg || !cpld_client) + if (!vpif_vidclkctl_reg || !cpld_client) return -ENXIO; val = i2c_smbus_read_byte(cpld_client); @@ -572,7 +572,7 @@ static int setup_vpif_input_channel_mode(int mux_mode) return val; spin_lock_irqsave(&vpif_reg_lock, flags); - value = __raw_readl(vpif_vsclkdis_reg); + value = __raw_readl(vpif_vidclkctl_reg); if (mux_mode) { val &= VPIF_INPUT_TWO_CHANNEL; value |= VIDCH1CLK; @@ -580,7 +580,7 @@ static int setup_vpif_input_channel_mode(int mux_mode) val |= VPIF_INPUT_ONE_CHANNEL; value &= ~VIDCH1CLK; } - __raw_writel(value, vpif_vsclkdis_reg); + __raw_writel(value, vpif_vidclkctl_reg); spin_unlock_irqrestore(&vpif_reg_lock, flags); err = i2c_smbus_write_byte(cpld_client, val); diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index 0b68ed534f8e..af27c130595f 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -161,7 +161,6 @@ static struct clk dsp_clk = { .name = "dsp", .parent = &pll1_sysclk1, .lpsc = DM646X_LPSC_C64X_CPU, - .flags = PSC_DSP, .usecount = 1, /* REVISIT how to disable? */ }; diff --git a/arch/arm/mach-davinci/include/mach/psc.h b/arch/arm/mach-davinci/include/mach/psc.h index fa59c097223d..8bc3fc256171 100644 --- a/arch/arm/mach-davinci/include/mach/psc.h +++ b/arch/arm/mach-davinci/include/mach/psc.h @@ -233,7 +233,7 @@ #define PTCMD 0x120 #define PTSTAT 0x128 #define PDSTAT 0x200 -#define PDCTL1 0x304 +#define PDCTL 0x300 #define MDSTAT 0x800 #define MDCTL 0xA00 @@ -244,7 +244,10 @@ #define PSC_STATE_ENABLE 3 #define MDSTAT_STATE_MASK 0x3f +#define PDSTAT_STATE_MASK 0x1f #define MDCTL_FORCE BIT(31) +#define PDCTL_NEXT BIT(1) +#define PDCTL_EPCGOOD BIT(8) #ifndef __ASSEMBLER__ diff --git a/arch/arm/mach-davinci/psc.c b/arch/arm/mach-davinci/psc.c index 1fb6bdff38c1..d7e210f4b55c 100644 --- a/arch/arm/mach-davinci/psc.c +++ b/arch/arm/mach-davinci/psc.c @@ -52,7 +52,7 @@ int __init davinci_psc_is_clk_active(unsigned int ctlr, unsigned int id) void davinci_psc_config(unsigned int domain, unsigned int ctlr, unsigned int id, bool enable, u32 flags) { - u32 epcpr, ptcmd, ptstat, pdstat, pdctl1, mdstat, mdctl; + u32 epcpr, ptcmd, ptstat, pdstat, pdctl, mdstat, mdctl; void __iomem *psc_base; struct davinci_soc_info *soc_info = &davinci_soc_info; u32 next_state = PSC_STATE_ENABLE; @@ -79,11 +79,11 @@ void davinci_psc_config(unsigned int domain, unsigned int ctlr, mdctl |= MDCTL_FORCE; __raw_writel(mdctl, psc_base + MDCTL + 4 * id); - pdstat = __raw_readl(psc_base + PDSTAT); - if ((pdstat & 0x00000001) == 0) { - pdctl1 = __raw_readl(psc_base + PDCTL1); - pdctl1 |= 0x1; - __raw_writel(pdctl1, psc_base + PDCTL1); + pdstat = __raw_readl(psc_base + PDSTAT + 4 * domain); + if ((pdstat & PDSTAT_STATE_MASK) == 0) { + pdctl = __raw_readl(psc_base + PDCTL + 4 * domain); + pdctl |= PDCTL_NEXT; + __raw_writel(pdctl, psc_base + PDCTL + 4 * domain); ptcmd = 1 << domain; __raw_writel(ptcmd, psc_base + PTCMD); @@ -92,9 +92,9 @@ void davinci_psc_config(unsigned int domain, unsigned int ctlr, epcpr = __raw_readl(psc_base + EPCPR); } while ((((epcpr >> domain) & 1) == 0)); - pdctl1 = __raw_readl(psc_base + PDCTL1); - pdctl1 |= 0x100; - __raw_writel(pdctl1, psc_base + PDCTL1); + pdctl = __raw_readl(psc_base + PDCTL + 4 * domain); + pdctl |= PDCTL_EPCGOOD; + __raw_writel(pdctl, psc_base + PDCTL + 4 * domain); } else { ptcmd = 1 << domain; __raw_writel(ptcmd, psc_base + PTCMD); diff --git a/arch/arm/mach-exynos/cpuidle.c b/arch/arm/mach-exynos/cpuidle.c index 35f6502144ae..4ebb382c5979 100644 --- a/arch/arm/mach-exynos/cpuidle.c +++ b/arch/arm/mach-exynos/cpuidle.c @@ -12,6 +12,8 @@ #include <linux/init.h> #include <linux/cpuidle.h> #include <linux/io.h> +#include <linux/export.h> +#include <linux/time.h> #include <asm/proc-fns.h> diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c index b82dcf08e747..88660d500f5b 100644 --- a/arch/arm/mach-highbank/highbank.c +++ b/arch/arm/mach-highbank/highbank.c @@ -22,6 +22,7 @@ #include <linux/of_irq.h> #include <linux/of_platform.h> #include <linux/of_address.h> +#include <linux/smp.h> #include <asm/cacheflush.h> #include <asm/unified.h> @@ -72,6 +73,9 @@ static void __init highbank_map_io(void) void highbank_set_cpu_jump(int cpu, void *jump_addr) { +#ifdef CONFIG_SMP + cpu = cpu_logical_map(cpu); +#endif writel(BSYM(virt_to_phys(jump_addr)), HB_JUMP_TABLE_VIRT(cpu)); __cpuc_flush_dcache_area(HB_JUMP_TABLE_VIRT(cpu), 16); outer_clean_range(HB_JUMP_TABLE_PHYS(cpu), diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 5f7f9c2a34ae..c44aa974e79c 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -10,11 +10,6 @@ config HAVE_IMX_MMDC config HAVE_IMX_SRC bool -# -# ARCH_MX31 and ARCH_MX35 are left for compatibility -# Some usages assume that having one of them implies not having (e.g.) ARCH_MX2. -# To easily distinguish good and reviewed from unreviewed usages new (and IMHO -# more sensible) names are used: SOC_IMX31 and SOC_IMX35 config ARCH_MX1 bool @@ -27,12 +22,6 @@ config ARCH_MX25 config MACH_MX27 bool -config ARCH_MX31 - bool - -config ARCH_MX35 - bool - config SOC_IMX1 bool select ARCH_MX1 @@ -72,7 +61,6 @@ config SOC_IMX31 select CPU_V6 select IMX_HAVE_PLATFORM_MXC_RNGA select ARCH_MXC_AUDMUX_V2 - select ARCH_MX31 select MXC_AVIC select SMP_ON_UP if SMP @@ -82,7 +70,6 @@ config SOC_IMX35 select ARCH_MXC_IOMUX_V3 select ARCH_MXC_AUDMUX_V2 select HAVE_EPIT - select ARCH_MX35 select MXC_AVIC select SMP_ON_UP if SMP diff --git a/arch/arm/mach-imx/clock-imx6q.c b/arch/arm/mach-imx/clock-imx6q.c index 613a1b993bff..039a7abb165a 100644 --- a/arch/arm/mach-imx/clock-imx6q.c +++ b/arch/arm/mach-imx/clock-imx6q.c @@ -1953,14 +1953,17 @@ static struct map_desc imx6q_clock_desc[] = { imx_map_entry(MX6Q, ANATOP, MT_DEVICE), }; +void __init imx6q_clock_map_io(void) +{ + iotable_init(imx6q_clock_desc, ARRAY_SIZE(imx6q_clock_desc)); +} + int __init mx6q_clocks_init(void) { struct device_node *np; void __iomem *base; int i, irq; - iotable_init(imx6q_clock_desc, ARRAY_SIZE(imx6q_clock_desc)); - /* retrieve the freqency of fixed clocks from device tree */ for_each_compatible_node(np, NULL, "fixed-clock") { u32 rate; diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c index 8bf5fa349484..8deb012189b5 100644 --- a/arch/arm/mach-imx/mach-imx6q.c +++ b/arch/arm/mach-imx/mach-imx6q.c @@ -34,16 +34,18 @@ static void __init imx6q_map_io(void) { imx_lluart_map_io(); imx_scu_map_io(); + imx6q_clock_map_io(); } -static void __init imx6q_gpio_add_irq_domain(struct device_node *np, +static int __init imx6q_gpio_add_irq_domain(struct device_node *np, struct device_node *interrupt_parent) { - static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS - - 32 * 7; /* imx6q gets 7 gpio ports */ + static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS; + gpio_irq_base -= 32; irq_domain_add_simple(np, gpio_irq_base); - gpio_irq_base += 32; + + return 0; } static const struct of_device_id imx6q_irq_match[] __initconst = { diff --git a/arch/arm/mach-imx/mm-imx3.c b/arch/arm/mach-imx/mm-imx3.c index 9f0e82ec3398..31807d2a8b7b 100644 --- a/arch/arm/mach-imx/mm-imx3.c +++ b/arch/arm/mach-imx/mm-imx3.c @@ -33,29 +33,32 @@ static void imx3_idle(void) { unsigned long reg = 0; - __asm__ __volatile__( - /* disable I and D cache */ - "mrc p15, 0, %0, c1, c0, 0\n" - "bic %0, %0, #0x00001000\n" - "bic %0, %0, #0x00000004\n" - "mcr p15, 0, %0, c1, c0, 0\n" - /* invalidate I cache */ - "mov %0, #0\n" - "mcr p15, 0, %0, c7, c5, 0\n" - /* clear and invalidate D cache */ - "mov %0, #0\n" - "mcr p15, 0, %0, c7, c14, 0\n" - /* WFI */ - "mov %0, #0\n" - "mcr p15, 0, %0, c7, c0, 4\n" - "nop\n" "nop\n" "nop\n" "nop\n" - "nop\n" "nop\n" "nop\n" - /* enable I and D cache */ - "mrc p15, 0, %0, c1, c0, 0\n" - "orr %0, %0, #0x00001000\n" - "orr %0, %0, #0x00000004\n" - "mcr p15, 0, %0, c1, c0, 0\n" - : "=r" (reg)); + + if (!need_resched()) + __asm__ __volatile__( + /* disable I and D cache */ + "mrc p15, 0, %0, c1, c0, 0\n" + "bic %0, %0, #0x00001000\n" + "bic %0, %0, #0x00000004\n" + "mcr p15, 0, %0, c1, c0, 0\n" + /* invalidate I cache */ + "mov %0, #0\n" + "mcr p15, 0, %0, c7, c5, 0\n" + /* clear and invalidate D cache */ + "mov %0, #0\n" + "mcr p15, 0, %0, c7, c14, 0\n" + /* WFI */ + "mov %0, #0\n" + "mcr p15, 0, %0, c7, c0, 4\n" + "nop\n" "nop\n" "nop\n" "nop\n" + "nop\n" "nop\n" "nop\n" + /* enable I and D cache */ + "mrc p15, 0, %0, c1, c0, 0\n" + "orr %0, %0, #0x00001000\n" + "orr %0, %0, #0x00000004\n" + "mcr p15, 0, %0, c1, c0, 0\n" + : "=r" (reg)); + local_irq_enable(); } static void __iomem *imx3_ioremap(unsigned long phys_addr, size_t size, @@ -108,6 +111,7 @@ void imx3_init_l2x0(void) l2x0_init(l2x0_base, 0x00030024, 0x00000000); } +#ifdef CONFIG_SOC_IMX31 static struct map_desc mx31_io_desc[] __initdata = { imx_map_entry(MX31, X_MEMC, MT_DEVICE), imx_map_entry(MX31, AVIC, MT_DEVICE_NONSHARED), @@ -126,33 +130,11 @@ void __init mx31_map_io(void) iotable_init(mx31_io_desc, ARRAY_SIZE(mx31_io_desc)); } -static struct map_desc mx35_io_desc[] __initdata = { - imx_map_entry(MX35, X_MEMC, MT_DEVICE), - imx_map_entry(MX35, AVIC, MT_DEVICE_NONSHARED), - imx_map_entry(MX35, AIPS1, MT_DEVICE_NONSHARED), - imx_map_entry(MX35, AIPS2, MT_DEVICE_NONSHARED), - imx_map_entry(MX35, SPBA0, MT_DEVICE_NONSHARED), -}; - -void __init mx35_map_io(void) -{ - iotable_init(mx35_io_desc, ARRAY_SIZE(mx35_io_desc)); -} - void __init imx31_init_early(void) { mxc_set_cpu_type(MXC_CPU_MX31); mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR)); - imx_idle = imx3_idle; - imx_ioremap = imx3_ioremap; -} - -void __init imx35_init_early(void) -{ - mxc_set_cpu_type(MXC_CPU_MX35); - mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR)); - mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR)); - imx_idle = imx3_idle; + pm_idle = imx3_idle; imx_ioremap = imx3_ioremap; } @@ -161,11 +143,6 @@ void __init mx31_init_irq(void) mxc_init_irq(MX31_IO_ADDRESS(MX31_AVIC_BASE_ADDR)); } -void __init mx35_init_irq(void) -{ - mxc_init_irq(MX35_IO_ADDRESS(MX35_AVIC_BASE_ADDR)); -} - static struct sdma_script_start_addrs imx31_to1_sdma_script __initdata = { .per_2_per_addr = 1677, }; @@ -199,6 +176,35 @@ void __init imx31_soc_init(void) imx_add_imx_sdma("imx31-sdma", MX31_SDMA_BASE_ADDR, MX31_INT_SDMA, &imx31_sdma_pdata); } +#endif /* ifdef CONFIG_SOC_IMX31 */ + +#ifdef CONFIG_SOC_IMX35 +static struct map_desc mx35_io_desc[] __initdata = { + imx_map_entry(MX35, X_MEMC, MT_DEVICE), + imx_map_entry(MX35, AVIC, MT_DEVICE_NONSHARED), + imx_map_entry(MX35, AIPS1, MT_DEVICE_NONSHARED), + imx_map_entry(MX35, AIPS2, MT_DEVICE_NONSHARED), + imx_map_entry(MX35, SPBA0, MT_DEVICE_NONSHARED), +}; + +void __init mx35_map_io(void) +{ + iotable_init(mx35_io_desc, ARRAY_SIZE(mx35_io_desc)); +} + +void __init imx35_init_early(void) +{ + mxc_set_cpu_type(MXC_CPU_MX35); + mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR)); + mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR)); + pm_idle = imx3_idle; + imx_ioremap = imx3_ioremap; +} + +void __init mx35_init_irq(void) +{ + mxc_init_irq(MX35_IO_ADDRESS(MX35_AVIC_BASE_ADDR)); +} static struct sdma_script_start_addrs imx35_to1_sdma_script __initdata = { .ap_2_ap_addr = 642, @@ -254,3 +260,4 @@ void __init imx35_soc_init(void) imx_add_imx_sdma("imx35-sdma", MX35_SDMA_BASE_ADDR, MX35_INT_SDMA, &imx35_sdma_pdata); } +#endif /* ifdef CONFIG_SOC_IMX35 */ diff --git a/arch/arm/mach-imx/src.c b/arch/arm/mach-imx/src.c index 36cacbd0dcc2..a8e33681b732 100644 --- a/arch/arm/mach-imx/src.c +++ b/arch/arm/mach-imx/src.c @@ -14,6 +14,7 @@ #include <linux/io.h> #include <linux/of.h> #include <linux/of_address.h> +#include <linux/smp.h> #include <asm/unified.h> #define SRC_SCR 0x000 @@ -23,10 +24,15 @@ static void __iomem *src_base; +#ifndef CONFIG_SMP +#define cpu_logical_map(cpu) 0 +#endif + void imx_enable_cpu(int cpu, bool enable) { u32 mask, val; + cpu = cpu_logical_map(cpu); mask = 1 << (BP_SRC_SCR_CORE1_ENABLE + cpu - 1); val = readl_relaxed(src_base + SRC_SCR); val = enable ? val | mask : val & ~mask; @@ -35,6 +41,7 @@ void imx_enable_cpu(int cpu, bool enable) void imx_set_cpu_jump(int cpu, void *jump_addr) { + cpu = cpu_logical_map(cpu); writel_relaxed(BSYM(virt_to_phys(jump_addr)), src_base + SRC_GPR1 + cpu * 8); } diff --git a/arch/arm/mach-mmp/gplugd.c b/arch/arm/mach-mmp/gplugd.c index 69156568bc41..4665767a4f79 100644 --- a/arch/arm/mach-mmp/gplugd.c +++ b/arch/arm/mach-mmp/gplugd.c @@ -182,7 +182,7 @@ static void __init gplugd_init(void) /* on-chip devices */ pxa168_add_uart(3); - pxa168_add_ssp(0); + pxa168_add_ssp(1); pxa168_add_twsi(0, NULL, ARRAY_AND_SIZE(gplugd_i2c_board_info)); pxa168_add_eth(&gplugd_eth_platform_data); diff --git a/arch/arm/mach-mmp/include/mach/gpio-pxa.h b/arch/arm/mach-mmp/include/mach/gpio-pxa.h index d14eeaf16322..99b4ce1b6562 100644 --- a/arch/arm/mach-mmp/include/mach/gpio-pxa.h +++ b/arch/arm/mach-mmp/include/mach/gpio-pxa.h @@ -7,7 +7,7 @@ #define GPIO_REGS_VIRT (APB_VIRT_BASE + 0x19000) #define BANK_OFF(n) (((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2)) -#define GPIO_REG(x) (GPIO_REGS_VIRT + (x)) +#define GPIO_REG(x) (*(volatile u32 *)(GPIO_REGS_VIRT + (x))) #define NR_BUILTIN_GPIO IRQ_GPIO_NUM diff --git a/arch/arm/mach-msm/Kconfig b/arch/arm/mach-msm/Kconfig index ebde97f5d5f0..000ddf0a4f33 100644 --- a/arch/arm/mach-msm/Kconfig +++ b/arch/arm/mach-msm/Kconfig @@ -13,7 +13,6 @@ config ARCH_MSM7X00A select CPU_V6 select GPIO_MSM_V1 select MSM_PROC_COMM - select HAS_MSM_DEBUG_UART_PHYS config ARCH_MSM7X30 bool "MSM7x30" @@ -25,7 +24,6 @@ config ARCH_MSM7X30 select MSM_GPIOMUX select GPIO_MSM_V1 select MSM_PROC_COMM - select HAS_MSM_DEBUG_UART_PHYS config ARCH_QSD8X50 bool "QSD8X50" @@ -37,7 +35,6 @@ config ARCH_QSD8X50 select MSM_GPIOMUX select GPIO_MSM_V1 select MSM_PROC_COMM - select HAS_MSM_DEBUG_UART_PHYS config ARCH_MSM8X60 bool "MSM8X60" @@ -63,6 +60,9 @@ config ARCH_MSM8960 endchoice +config MSM_HAS_DEBUG_UART_HS + bool + config MSM_SOC_REV_A bool config ARCH_MSM_SCORPIONMP @@ -73,9 +73,6 @@ config ARCH_MSM_ARM11 config ARCH_MSM_SCORPION bool -config HAS_MSM_DEBUG_UART_PHYS - bool - config MSM_VIC bool @@ -152,32 +149,6 @@ config MACH_MSM8960_RUMI3 endmenu -config MSM_DEBUG_UART - int - default 1 if MSM_DEBUG_UART1 - default 2 if MSM_DEBUG_UART2 - default 3 if MSM_DEBUG_UART3 - -if HAS_MSM_DEBUG_UART_PHYS -choice - prompt "Debug UART" - - default MSM_DEBUG_UART_NONE - - config MSM_DEBUG_UART_NONE - bool "None" - - config MSM_DEBUG_UART1 - bool "UART1" - - config MSM_DEBUG_UART2 - bool "UART2" - - config MSM_DEBUG_UART3 - bool "UART3" -endchoice -endif - config MSM_SMD_PKG3 bool diff --git a/arch/arm/mach-msm/devices-iommu.c b/arch/arm/mach-msm/devices-iommu.c index 24030d0da6e3..0fb7a17df398 100644 --- a/arch/arm/mach-msm/devices-iommu.c +++ b/arch/arm/mach-msm/devices-iommu.c @@ -18,6 +18,7 @@ #include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/bootmem.h> +#include <linux/module.h> #include <mach/irqs.h> #include <mach/iommu.h> diff --git a/arch/arm/mach-msm/include/mach/debug-macro.S b/arch/arm/mach-msm/include/mach/debug-macro.S index 2dc73ccddb11..3ffd8668c9a5 100644 --- a/arch/arm/mach-msm/include/mach/debug-macro.S +++ b/arch/arm/mach-msm/include/mach/debug-macro.S @@ -1,6 +1,7 @@ -/* arch/arm/mach-msm7200/include/mach/debug-macro.S +/* * * Copyright (C) 2007 Google, Inc. + * Copyright (c) 2011, Code Aurora Forum. All rights reserved. * Author: Brian Swetland <swetland@google.com> * * This software is licensed under the terms of the GNU General Public @@ -14,40 +15,52 @@ * */ - - #include <mach/hardware.h> #include <mach/msm_iomap.h> -#if defined(CONFIG_HAS_MSM_DEBUG_UART_PHYS) && !defined(CONFIG_MSM_DEBUG_UART_NONE) .macro addruart, rp, rv, tmp +#ifdef MSM_DEBUG_UART_PHYS ldr \rp, =MSM_DEBUG_UART_PHYS ldr \rv, =MSM_DEBUG_UART_BASE +#endif .endm - .macro senduart,rd,rx + .macro senduart, rd, rx +#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS + @ Write the 1 character to UARTDM_TF + str \rd, [\rx, #0x70] +#else teq \rx, #0 strne \rd, [\rx, #0x0C] +#endif .endm - .macro waituart,rd,rx + .macro waituart, rd, rx +#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS + @ check for TX_EMT in UARTDM_SR + ldr \rd, [\rx, #0x08] + tst \rd, #0x08 + bne 1002f + @ wait for TXREADY in UARTDM_ISR +1001: ldr \rd, [\rx, #0x14] + tst \rd, #0x80 + beq 1001b +1002: + @ Clear TX_READY by writing to the UARTDM_CR register + mov \rd, #0x300 + str \rd, [\rx, #0x10] + @ Write 0x1 to NCF register + mov \rd, #0x1 + str \rd, [\rx, #0x40] + @ UARTDM reg. Read to induce delay + ldr \rd, [\rx, #0x08] +#else @ wait for TX_READY 1001: ldr \rd, [\rx, #0x08] tst \rd, #0x04 beq 1001b - .endm -#else - .macro addruart, rp, rv, tmp - mov \rv, #0xff000000 - orr \rv, \rv, #0x00f00000 - .endm - - .macro senduart,rd,rx - .endm - - .macro waituart,rd,rx - .endm #endif + .endm - .macro busyuart,rd,rx + .macro busyuart, rd, rx .endm diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h b/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h index 94fe9fe6feb3..8af46123dab6 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap-7x00.h @@ -78,18 +78,6 @@ #define MSM_UART3_PHYS 0xA9C00000 #define MSM_UART3_SIZE SZ_4K -#ifdef CONFIG_MSM_DEBUG_UART -#define MSM_DEBUG_UART_BASE 0xE1000000 -#if CONFIG_MSM_DEBUG_UART == 1 -#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS -#elif CONFIG_MSM_DEBUG_UART == 2 -#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS -#elif CONFIG_MSM_DEBUG_UART == 3 -#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS -#endif -#define MSM_DEBUG_UART_SIZE SZ_4K -#endif - #define MSM_SDC1_PHYS 0xA0400000 #define MSM_SDC1_SIZE SZ_4K diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-7x30.h b/arch/arm/mach-msm/include/mach/msm_iomap-7x30.h index 37694442d1bd..198202c267c8 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap-7x30.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap-7x30.h @@ -89,18 +89,6 @@ #define MSM_UART3_PHYS 0xACC00000 #define MSM_UART3_SIZE SZ_4K -#ifdef CONFIG_MSM_DEBUG_UART -#define MSM_DEBUG_UART_BASE 0xE1000000 -#if CONFIG_MSM_DEBUG_UART == 1 -#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS -#elif CONFIG_MSM_DEBUG_UART == 2 -#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS -#elif CONFIG_MSM_DEBUG_UART == 3 -#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS -#endif -#define MSM_DEBUG_UART_SIZE SZ_4K -#endif - #define MSM_MDC_BASE IOMEM(0xE0200000) #define MSM_MDC_PHYS 0xAA500000 #define MSM_MDC_SIZE SZ_1M diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-8960.h b/arch/arm/mach-msm/include/mach/msm_iomap-8960.h index 3c9d9602a318..800b55767e6b 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap-8960.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap-8960.h @@ -45,4 +45,9 @@ #define MSM8960_TMR0_PHYS 0x0208A000 #define MSM8960_TMR0_SIZE SZ_4K +#ifdef CONFIG_DEBUG_MSM8960_UART +#define MSM_DEBUG_UART_BASE 0xE1040000 +#define MSM_DEBUG_UART_PHYS 0x16440000 +#endif + #endif diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-8x50.h b/arch/arm/mach-msm/include/mach/msm_iomap-8x50.h index d67cd73316f4..0faa894729b7 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap-8x50.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap-8x50.h @@ -83,18 +83,6 @@ #define MSM_UART3_PHYS 0xA9C00000 #define MSM_UART3_SIZE SZ_4K -#ifdef CONFIG_MSM_DEBUG_UART -#define MSM_DEBUG_UART_BASE 0xE1000000 -#if CONFIG_MSM_DEBUG_UART == 1 -#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS -#elif CONFIG_MSM_DEBUG_UART == 2 -#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS -#elif CONFIG_MSM_DEBUG_UART == 3 -#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS -#endif -#define MSM_DEBUG_UART_SIZE SZ_4K -#endif - #define MSM_MDC_BASE IOMEM(0xE0200000) #define MSM_MDC_PHYS 0xAA500000 #define MSM_MDC_SIZE SZ_1M diff --git a/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h b/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h index 3b19b8f244b8..54e12caa8d86 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap-8x60.h @@ -62,4 +62,9 @@ #define MSM8X60_TMR0_PHYS 0x02040000 #define MSM8X60_TMR0_SIZE SZ_4K +#ifdef CONFIG_DEBUG_MSM8660_UART +#define MSM_DEBUG_UART_BASE 0xE1040000 +#define MSM_DEBUG_UART_PHYS 0x19C40000 +#endif + #endif diff --git a/arch/arm/mach-msm/include/mach/msm_iomap.h b/arch/arm/mach-msm/include/mach/msm_iomap.h index 4ded15238b60..90682f4599d3 100644 --- a/arch/arm/mach-msm/include/mach/msm_iomap.h +++ b/arch/arm/mach-msm/include/mach/msm_iomap.h @@ -55,6 +55,18 @@ #include "msm_iomap-8960.h" +#define MSM_DEBUG_UART_SIZE SZ_4K +#if defined(CONFIG_DEBUG_MSM_UART1) +#define MSM_DEBUG_UART_BASE 0xE1000000 +#define MSM_DEBUG_UART_PHYS MSM_UART1_PHYS +#elif defined(CONFIG_DEBUG_MSM_UART2) +#define MSM_DEBUG_UART_BASE 0xE1000000 +#define MSM_DEBUG_UART_PHYS MSM_UART2_PHYS +#elif defined(CONFIG_DEBUG_MSM_UART3) +#define MSM_DEBUG_UART_BASE 0xE1000000 +#define MSM_DEBUG_UART_PHYS MSM_UART3_PHYS +#endif + /* Virtual addresses shared across all MSM targets. */ #define MSM_CSR_BASE IOMEM(0xE0001000) #define MSM_QGIC_DIST_BASE IOMEM(0xF0000000) diff --git a/arch/arm/mach-msm/include/mach/uncompress.h b/arch/arm/mach-msm/include/mach/uncompress.h index d94292c29d8e..169a84007456 100644 --- a/arch/arm/mach-msm/include/mach/uncompress.h +++ b/arch/arm/mach-msm/include/mach/uncompress.h @@ -1,6 +1,6 @@ -/* arch/arm/mach-msm/include/mach/uncompress.h - * +/* * Copyright (C) 2007 Google, Inc. + * Copyright (c) 2011, Code Aurora Forum. All rights reserved. * * This software is licensed under the terms of the GNU General Public * License version 2, as published by the Free Software Foundation, and @@ -14,17 +14,40 @@ */ #ifndef __ASM_ARCH_MSM_UNCOMPRESS_H +#define __ASM_ARCH_MSM_UNCOMPRESS_H + +#include <asm/processor.h> +#include <mach/msm_iomap.h> + +#define UART_CSR (*(volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x08)) +#define UART_TF (*(volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x0c)) -#include "hardware.h" -#include "linux/io.h" -#include "mach/msm_iomap.h" +#define UART_DM_SR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x08))) +#define UART_DM_CR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x10))) +#define UART_DM_ISR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x14))) +#define UART_DM_NCHAR (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x40))) +#define UART_DM_TF (*((volatile uint32_t *)(MSM_DEBUG_UART_PHYS + 0x70))) static void putc(int c) { #if defined(MSM_DEBUG_UART_PHYS) - unsigned base = MSM_DEBUG_UART_PHYS; - while (!(readl(base + 0x08) & 0x04)) ; - writel(c, base + 0x0c); +#ifdef CONFIG_MSM_HAS_DEBUG_UART_HS + /* + * Wait for TX_READY to be set; but skip it if we have a + * TX underrun. + */ + if (UART_DM_SR & 0x08) + while (!(UART_DM_ISR & 0x80)) + cpu_relax(); + + UART_DM_CR = 0x300; + UART_DM_NCHAR = 0x1; + UART_DM_TF = c; +#else + while (!(UART_CSR & 0x04)) + cpu_relax(); + UART_TF = c; +#endif #endif } diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c index 8759ecf7454f..578b04e42deb 100644 --- a/arch/arm/mach-msm/io.c +++ b/arch/arm/mach-msm/io.c @@ -47,7 +47,8 @@ static struct map_desc msm_io_desc[] __initdata = { MSM_CHIP_DEVICE(GPIO1, MSM7X00), MSM_CHIP_DEVICE(GPIO2, MSM7X00), MSM_DEVICE(CLK_CTL), -#ifdef CONFIG_MSM_DEBUG_UART +#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \ + defined(CONFIG_DEBUG_MSM_UART3) MSM_DEVICE(DEBUG_UART), #endif #ifdef CONFIG_ARCH_MSM7X30 @@ -84,7 +85,8 @@ static struct map_desc qsd8x50_io_desc[] __initdata = { MSM_DEVICE(SCPLL), MSM_DEVICE(AD5), MSM_DEVICE(MDC), -#ifdef CONFIG_MSM_DEBUG_UART +#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \ + defined(CONFIG_DEBUG_MSM_UART3) MSM_DEVICE(DEBUG_UART), #endif { @@ -109,6 +111,9 @@ static struct map_desc msm8x60_io_desc[] __initdata = { MSM_CHIP_DEVICE(TMR0, MSM8X60), MSM_DEVICE(ACC), MSM_DEVICE(GCC), +#ifdef CONFIG_DEBUG_MSM8660_UART + MSM_DEVICE(DEBUG_UART), +#endif }; void __init msm_map_msm8x60_io(void) @@ -123,6 +128,9 @@ static struct map_desc msm8960_io_desc[] __initdata = { MSM_CHIP_DEVICE(QGIC_CPU, MSM8960), MSM_CHIP_DEVICE(TMR, MSM8960), MSM_CHIP_DEVICE(TMR0, MSM8960), +#ifdef CONFIG_DEBUG_MSM8960_UART + MSM_DEVICE(DEBUG_UART), +#endif }; void __init msm_map_msm8960_io(void) @@ -146,7 +154,8 @@ static struct map_desc msm7x30_io_desc[] __initdata = { MSM_DEVICE(SAW), MSM_DEVICE(GCC), MSM_DEVICE(TCSR), -#ifdef CONFIG_MSM_DEBUG_UART +#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \ + defined(CONFIG_DEBUG_MSM_UART3) MSM_DEVICE(DEBUG_UART), #endif { diff --git a/arch/arm/mach-msm/platsmp.c b/arch/arm/mach-msm/platsmp.c index fdec58aaa35c..0b3e357c4c8c 100644 --- a/arch/arm/mach-msm/platsmp.c +++ b/arch/arm/mach-msm/platsmp.c @@ -79,7 +79,7 @@ static __cpuinit void prepare_cold_cpu(unsigned int cpu) ret = scm_set_boot_addr(virt_to_phys(msm_secondary_startup), SCM_FLAG_COLDBOOT_CPU1); if (ret == 0) { - void *sc1_base_ptr; + void __iomem *sc1_base_ptr; sc1_base_ptr = ioremap_nocache(0x00902000, SZ_4K*2); if (sc1_base_ptr) { writel(0, sc1_base_ptr + VDD_SC1_ARRAY_CLAMP_GFS_CTL); diff --git a/arch/arm/mach-mx5/cpu.c b/arch/arm/mach-mx5/cpu.c index 5c5328257dca..5e2e7a843860 100644 --- a/arch/arm/mach-mx5/cpu.c +++ b/arch/arm/mach-mx5/cpu.c @@ -16,7 +16,7 @@ #include <linux/init.h> #include <linux/module.h> #include <mach/hardware.h> -#include <asm/io.h> +#include <linux/io.h> static int mx5_cpu_rev = -1; @@ -67,7 +67,8 @@ static int __init mx51_neon_fixup(void) if (!cpu_is_mx51()) return 0; - if (mx51_revision() < IMX_CHIP_REVISION_3_0 && (elf_hwcap & HWCAP_NEON)) { + if (mx51_revision() < IMX_CHIP_REVISION_3_0 && + (elf_hwcap & HWCAP_NEON)) { elf_hwcap &= ~HWCAP_NEON; pr_info("Turning off NEON support, detected broken NEON implementation\n"); } diff --git a/arch/arm/mach-mx5/imx51-dt.c b/arch/arm/mach-mx5/imx51-dt.c index ccc61585659b..596edd967dbf 100644 --- a/arch/arm/mach-mx5/imx51-dt.c +++ b/arch/arm/mach-mx5/imx51-dt.c @@ -44,20 +44,22 @@ static const struct of_dev_auxdata imx51_auxdata_lookup[] __initconst = { { /* sentinel */ } }; -static void __init imx51_tzic_add_irq_domain(struct device_node *np, +static int __init imx51_tzic_add_irq_domain(struct device_node *np, struct device_node *interrupt_parent) { irq_domain_add_simple(np, 0); + return 0; } -static void __init imx51_gpio_add_irq_domain(struct device_node *np, +static int __init imx51_gpio_add_irq_domain(struct device_node *np, struct device_node *interrupt_parent) { - static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS - - 32 * 4; /* imx51 gets 4 gpio ports */ + static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS; + gpio_irq_base -= 32; irq_domain_add_simple(np, gpio_irq_base); - gpio_irq_base += 32; + + return 0; } static const struct of_device_id imx51_irq_match[] __initconst = { diff --git a/arch/arm/mach-mx5/imx53-dt.c b/arch/arm/mach-mx5/imx53-dt.c index ccaa0b81b768..85bfd5ff21b0 100644 --- a/arch/arm/mach-mx5/imx53-dt.c +++ b/arch/arm/mach-mx5/imx53-dt.c @@ -48,20 +48,22 @@ static const struct of_dev_auxdata imx53_auxdata_lookup[] __initconst = { { /* sentinel */ } }; -static void __init imx53_tzic_add_irq_domain(struct device_node *np, +static int __init imx53_tzic_add_irq_domain(struct device_node *np, struct device_node *interrupt_parent) { irq_domain_add_simple(np, 0); + return 0; } -static void __init imx53_gpio_add_irq_domain(struct device_node *np, +static int __init imx53_gpio_add_irq_domain(struct device_node *np, struct device_node *interrupt_parent) { - static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS - - 32 * 7; /* imx53 gets 7 gpio ports */ + static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS; + gpio_irq_base -= 32; irq_domain_add_simple(np, gpio_irq_base); - gpio_irq_base += 32; + + return 0; } static const struct of_device_id imx53_irq_match[] __initconst = { diff --git a/arch/arm/mach-mx5/mm.c b/arch/arm/mach-mx5/mm.c index 26eacc9d0d90..df4a508f240a 100644 --- a/arch/arm/mach-mx5/mm.c +++ b/arch/arm/mach-mx5/mm.c @@ -23,7 +23,9 @@ static void imx5_idle(void) { - mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF); + if (!need_resched()) + mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF); + local_irq_enable(); } /* @@ -89,7 +91,7 @@ void __init imx51_init_early(void) mxc_set_cpu_type(MXC_CPU_MX51); mxc_iomux_v3_init(MX51_IO_ADDRESS(MX51_IOMUXC_BASE_ADDR)); mxc_arch_reset_init(MX51_IO_ADDRESS(MX51_WDOG1_BASE_ADDR)); - imx_idle = imx5_idle; + pm_idle = imx5_idle; } void __init imx53_init_early(void) diff --git a/arch/arm/mach-mxs/clock-mx28.c b/arch/arm/mach-mxs/clock-mx28.c index 229ae3494216..da6e4aad177c 100644 --- a/arch/arm/mach-mxs/clock-mx28.c +++ b/arch/arm/mach-mxs/clock-mx28.c @@ -404,7 +404,7 @@ static int name##_set_rate(struct clk *clk, unsigned long rate) \ reg = __raw_readl(CLKCTRL_BASE_ADDR + HW_CLKCTRL_##dr); \ reg &= ~BM_CLKCTRL_##dr##_DIV; \ reg |= div << BP_CLKCTRL_##dr##_DIV; \ - if (reg | (1 << clk->enable_shift)) { \ + if (reg & (1 << clk->enable_shift)) { \ pr_err("%s: clock is gated\n", __func__); \ return -EINVAL; \ } \ diff --git a/arch/arm/mach-mxs/include/mach/mx28.h b/arch/arm/mach-mxs/include/mach/mx28.h index 75d86118b76a..30c7990f3c01 100644 --- a/arch/arm/mach-mxs/include/mach/mx28.h +++ b/arch/arm/mach-mxs/include/mach/mx28.h @@ -104,8 +104,8 @@ #define MX28_INT_CAN1 9 #define MX28_INT_LRADC_TOUCH 10 #define MX28_INT_HSADC 13 -#define MX28_INT_IRADC_THRESH0 14 -#define MX28_INT_IRADC_THRESH1 15 +#define MX28_INT_LRADC_THRESH0 14 +#define MX28_INT_LRADC_THRESH1 15 #define MX28_INT_LRADC_CH0 16 #define MX28_INT_LRADC_CH1 17 #define MX28_INT_LRADC_CH2 18 diff --git a/arch/arm/mach-mxs/include/mach/mxs.h b/arch/arm/mach-mxs/include/mach/mxs.h index 0d2d2b470998..bde5f6634747 100644 --- a/arch/arm/mach-mxs/include/mach/mxs.h +++ b/arch/arm/mach-mxs/include/mach/mxs.h @@ -30,6 +30,7 @@ */ #define cpu_is_mx23() ( \ machine_is_mx23evk() || \ + machine_is_stmp378x() || \ 0) #define cpu_is_mx28() ( \ machine_is_mx28evk() || \ diff --git a/arch/arm/mach-mxs/mach-m28evk.c b/arch/arm/mach-mxs/mach-m28evk.c index 3b1681e4f49a..6b00577b7025 100644 --- a/arch/arm/mach-mxs/mach-m28evk.c +++ b/arch/arm/mach-mxs/mach-m28evk.c @@ -361,6 +361,6 @@ static struct sys_timer m28evk_timer = { MACHINE_START(M28EVK, "DENX M28 EVK") .map_io = mx28_map_io, .init_irq = mx28_init_irq, - .init_machine = m28evk_init, .timer = &m28evk_timer, + .init_machine = m28evk_init, MACHINE_END diff --git a/arch/arm/mach-mxs/mach-stmp378x_devb.c b/arch/arm/mach-mxs/mach-stmp378x_devb.c index 177e53123a02..6834dea38c04 100644 --- a/arch/arm/mach-mxs/mach-stmp378x_devb.c +++ b/arch/arm/mach-mxs/mach-stmp378x_devb.c @@ -115,6 +115,6 @@ static struct sys_timer stmp378x_dvb_timer = { MACHINE_START(STMP378X, "STMP378X") .map_io = mx23_map_io, .init_irq = mx23_init_irq, - .init_machine = stmp378x_dvb_init, .timer = &stmp378x_dvb_timer, + .init_machine = stmp378x_dvb_init, MACHINE_END diff --git a/arch/arm/mach-mxs/module-tx28.c b/arch/arm/mach-mxs/module-tx28.c index 0fcff47009cf..9a7b08b2a925 100644 --- a/arch/arm/mach-mxs/module-tx28.c +++ b/arch/arm/mach-mxs/module-tx28.c @@ -66,11 +66,11 @@ static const iomux_cfg_t tx28_fec1_pads[] __initconst = { MX28_PAD_ENET0_CRS__ENET1_RX_EN, }; -static struct fec_platform_data tx28_fec0_data = { +static const struct fec_platform_data tx28_fec0_data __initconst = { .phy = PHY_INTERFACE_MODE_RMII, }; -static struct fec_platform_data tx28_fec1_data = { +static const struct fec_platform_data tx28_fec1_data __initconst = { .phy = PHY_INTERFACE_MODE_RMII, }; diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig index e0a028161dde..73f287d6429b 100644 --- a/arch/arm/mach-omap1/Kconfig +++ b/arch/arm/mach-omap1/Kconfig @@ -171,14 +171,6 @@ config MACH_OMAP_GENERIC comment "OMAP CPU Speed" depends on ARCH_OMAP1 -config OMAP_CLOCKS_SET_BY_BOOTLOADER - bool "OMAP clocks set by bootloader" - depends on ARCH_OMAP1 - help - Enable this option to prevent the kernel from overriding the clock - frequencies programmed by bootloader for MPU, DSP, MMUs, TC, - internal LCD controller and MPU peripherals. - config OMAP_ARM_216MHZ bool "OMAP ARM 216 MHz CPU (1710 only)" depends on ARCH_OMAP1 && ARCH_OMAP16XX diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c index 51bae31cf361..b0f15d234a12 100644 --- a/arch/arm/mach-omap1/board-ams-delta.c +++ b/arch/arm/mach-omap1/board-ams-delta.c @@ -302,8 +302,6 @@ static void __init ams_delta_init(void) omap_cfg_reg(J19_1610_CAM_D6); omap_cfg_reg(J18_1610_CAM_D7); - iotable_init(ams_delta_io_desc, ARRAY_SIZE(ams_delta_io_desc)); - omap_board_config = ams_delta_config; omap_board_config_size = ARRAY_SIZE(ams_delta_config); omap_serial_init(); @@ -373,10 +371,16 @@ static int __init ams_delta_modem_init(void) } arch_initcall(ams_delta_modem_init); +static void __init ams_delta_map_io(void) +{ + omap15xx_map_io(); + iotable_init(ams_delta_io_desc, ARRAY_SIZE(ams_delta_io_desc)); +} + MACHINE_START(AMS_DELTA, "Amstrad E3 (Delta)") /* Maintainer: Jonathan McDowell <noodles@earth.li> */ .atag_offset = 0x100, - .map_io = omap15xx_map_io, + .map_io = ams_delta_map_io, .init_early = omap1_init_early, .reserve = omap_reserve, .init_irq = omap1_init_irq, diff --git a/arch/arm/mach-omap1/clock.h b/arch/arm/mach-omap1/clock.h index eaf09efb91ca..16b1423b454a 100644 --- a/arch/arm/mach-omap1/clock.h +++ b/arch/arm/mach-omap1/clock.h @@ -17,7 +17,8 @@ #include <plat/clock.h> -extern int __init omap1_clk_init(void); +int omap1_clk_init(void); +void omap1_clk_late_init(void); extern int omap1_clk_enable(struct clk *clk); extern void omap1_clk_disable(struct clk *clk); extern long omap1_clk_round_rate(struct clk *clk, unsigned long rate); diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c index 92400b9eb69f..9ff90a744a21 100644 --- a/arch/arm/mach-omap1/clock_data.c +++ b/arch/arm/mach-omap1/clock_data.c @@ -16,6 +16,8 @@ #include <linux/kernel.h> #include <linux/clk.h> +#include <linux/cpufreq.h> +#include <linux/delay.h> #include <linux/io.h> #include <asm/mach-types.h> /* for machine_is_* */ @@ -767,6 +769,15 @@ static struct clk_functions omap1_clk_functions = { .clk_disable_unused = omap1_clk_disable_unused, }; +static void __init omap1_show_rates(void) +{ + pr_notice("Clocking rate (xtal/DPLL1/MPU): " + "%ld.%01ld/%ld.%01ld/%ld.%01ld MHz\n", + ck_ref.rate / 1000000, (ck_ref.rate / 100000) % 10, + ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10, + arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10); +} + int __init omap1_clk_init(void) { struct omap_clk *c; @@ -835,9 +846,12 @@ int __init omap1_clk_init(void) /* We want to be in syncronous scalable mode */ omap_writew(0x1000, ARM_SYSST); -#ifdef CONFIG_OMAP_CLOCKS_SET_BY_BOOTLOADER - /* Use values set by bootloader. Determine PLL rate and recalculate - * dependent clocks as if kernel had changed PLL or divisors. + + /* + * Initially use the values set by bootloader. Determine PLL rate and + * recalculate dependent clocks as if kernel had changed PLL or + * divisors. See also omap1_clk_late_init() that can reprogram dpll1 + * after the SRAM is initialized. */ { unsigned pll_ctl_val = omap_readw(DPLL_CTL); @@ -862,25 +876,10 @@ int __init omap1_clk_init(void) } } } -#else - /* Find the highest supported frequency and enable it */ - if (omap1_select_table_rate(&virtual_ck_mpu, ~0)) { - printk(KERN_ERR "System frequencies not set. Check your config.\n"); - /* Guess sane values (60MHz) */ - omap_writew(0x2290, DPLL_CTL); - omap_writew(cpu_is_omap7xx() ? 0x3005 : 0x1005, ARM_CKCTL); - ck_dpll1.rate = 60000000; - } -#endif propagate_rate(&ck_dpll1); /* Cache rates for clocks connected to ck_ref (not dpll1) */ propagate_rate(&ck_ref); - printk(KERN_INFO "Clocking rate (xtal/DPLL1/MPU): " - "%ld.%01ld/%ld.%01ld/%ld.%01ld MHz\n", - ck_ref.rate / 1000000, (ck_ref.rate / 100000) % 10, - ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10, - arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10); - + omap1_show_rates(); if (machine_is_omap_perseus2() || machine_is_omap_fsample()) { /* Select slicer output as OMAP input clock */ omap_writew(omap_readw(OMAP7XX_PCC_UPLD_CTRL) & ~0x1, @@ -925,3 +924,27 @@ int __init omap1_clk_init(void) return 0; } + +#define OMAP1_DPLL1_SANE_VALUE 60000000 + +void __init omap1_clk_late_init(void) +{ + unsigned long rate = ck_dpll1.rate; + + if (rate >= OMAP1_DPLL1_SANE_VALUE) + return; + + /* System booting at unusable rate, force reprogramming of DPLL1 */ + ck_dpll1_p->rate = 0; + + /* Find the highest supported frequency and enable it */ + if (omap1_select_table_rate(&virtual_ck_mpu, ~0)) { + pr_err("System frequencies not set, using default. Check your config.\n"); + omap_writew(0x2290, DPLL_CTL); + omap_writew(cpu_is_omap7xx() ? 0x2005 : 0x0005, ARM_CKCTL); + ck_dpll1.rate = OMAP1_DPLL1_SANE_VALUE; + } + propagate_rate(&ck_dpll1); + omap1_show_rates(); + loops_per_jiffy = cpufreq_scale(loops_per_jiffy, rate, ck_dpll1.rate); +} diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c index 48ef9888e820..475cb2f50d87 100644 --- a/arch/arm/mach-omap1/devices.c +++ b/arch/arm/mach-omap1/devices.c @@ -30,6 +30,8 @@ #include <plat/omap7xx.h> #include <plat/mcbsp.h> +#include "clock.h" + /*-------------------------------------------------------------------------*/ #if defined(CONFIG_RTC_DRV_OMAP) || defined(CONFIG_RTC_DRV_OMAP_MODULE) @@ -293,6 +295,7 @@ static int __init omap1_init_devices(void) return -ENODEV; omap_sram_init(); + omap1_clk_late_init(); /* please keep these calls, and their implementations above, * in alphabetical order so they're easier to sort through. diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 503414718905..e1293aa513d3 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -334,6 +334,7 @@ config MACH_OMAP4_PANDA config OMAP3_EMU bool "OMAP3 debugging peripherals" depends on ARCH_OMAP3 + select ARM_AMBA select OC_ETM help Say Y here to enable debugging hardware of omap3 diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index 69ab1c069134..b009f17dee56 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -4,7 +4,7 @@ # Common support obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer.o pm.o \ - common.o gpio.o dma.o wd_timer.o + common.o gpio.o dma.o wd_timer.o display.o omap-2-3-common = irq.o sdrc.o hwmod-common = omap_hwmod.o \ @@ -264,7 +264,4 @@ smsc911x-$(CONFIG_SMSC911X) := gpmc-smsc911x.o obj-y += $(smsc911x-m) $(smsc911x-y) obj-$(CONFIG_ARCH_OMAP4) += hwspinlock.o -disp-$(CONFIG_OMAP2_DSS) := display.o -obj-y += $(disp-m) $(disp-y) - obj-y += common-board-devices.o twl-common.o diff --git a/arch/arm/mach-omap2/cpuidle34xx.c b/arch/arm/mach-omap2/cpuidle34xx.c index 1fe35c24fba2..942bb4f19f9f 100644 --- a/arch/arm/mach-omap2/cpuidle34xx.c +++ b/arch/arm/mach-omap2/cpuidle34xx.c @@ -24,6 +24,7 @@ #include <linux/sched.h> #include <linux/cpuidle.h> +#include <linux/export.h> #include <plat/prcm.h> #include <plat/irqs.h> diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c index adb2756e242f..dce9905d64bb 100644 --- a/arch/arm/mach-omap2/display.c +++ b/arch/arm/mach-omap2/display.c @@ -27,8 +27,35 @@ #include <plat/omap_hwmod.h> #include <plat/omap_device.h> #include <plat/omap-pm.h> +#include <plat/common.h> #include "control.h" +#include "display.h" + +#define DISPC_CONTROL 0x0040 +#define DISPC_CONTROL2 0x0238 +#define DISPC_IRQSTATUS 0x0018 + +#define DSS_SYSCONFIG 0x10 +#define DSS_SYSSTATUS 0x14 +#define DSS_CONTROL 0x40 +#define DSS_SDI_CONTROL 0x44 +#define DSS_PLL_CONTROL 0x48 + +#define LCD_EN_MASK (0x1 << 0) +#define DIGIT_EN_MASK (0x1 << 1) + +#define FRAMEDONE_IRQ_SHIFT 0 +#define EVSYNC_EVEN_IRQ_SHIFT 2 +#define EVSYNC_ODD_IRQ_SHIFT 3 +#define FRAMEDONE2_IRQ_SHIFT 22 +#define FRAMEDONETV_IRQ_SHIFT 24 + +/* + * FRAMEDONE_IRQ_TIMEOUT: how long (in milliseconds) to wait during DISPC + * reset before deciding that something has gone wrong + */ +#define FRAMEDONE_IRQ_TIMEOUT 100 static struct platform_device omap_display_device = { .name = "omapdss", @@ -172,3 +199,135 @@ int __init omap_display_init(struct omap_dss_board_info *board_data) return r; } + +static void dispc_disable_outputs(void) +{ + u32 v, irq_mask = 0; + bool lcd_en, digit_en, lcd2_en = false; + int i; + struct omap_dss_dispc_dev_attr *da; + struct omap_hwmod *oh; + + oh = omap_hwmod_lookup("dss_dispc"); + if (!oh) { + WARN(1, "display: could not disable outputs during reset - could not find dss_dispc hwmod\n"); + return; + } + + if (!oh->dev_attr) { + pr_err("display: could not disable outputs during reset due to missing dev_attr\n"); + return; + } + + da = (struct omap_dss_dispc_dev_attr *)oh->dev_attr; + + /* store value of LCDENABLE and DIGITENABLE bits */ + v = omap_hwmod_read(oh, DISPC_CONTROL); + lcd_en = v & LCD_EN_MASK; + digit_en = v & DIGIT_EN_MASK; + + /* store value of LCDENABLE for LCD2 */ + if (da->manager_count > 2) { + v = omap_hwmod_read(oh, DISPC_CONTROL2); + lcd2_en = v & LCD_EN_MASK; + } + + if (!(lcd_en | digit_en | lcd2_en)) + return; /* no managers currently enabled */ + + /* + * If any manager was enabled, we need to disable it before + * DSS clocks are disabled or DISPC module is reset + */ + if (lcd_en) + irq_mask |= 1 << FRAMEDONE_IRQ_SHIFT; + + if (digit_en) { + if (da->has_framedonetv_irq) { + irq_mask |= 1 << FRAMEDONETV_IRQ_SHIFT; + } else { + irq_mask |= 1 << EVSYNC_EVEN_IRQ_SHIFT | + 1 << EVSYNC_ODD_IRQ_SHIFT; + } + } + + if (lcd2_en) + irq_mask |= 1 << FRAMEDONE2_IRQ_SHIFT; + + /* + * clear any previous FRAMEDONE, FRAMEDONETV, + * EVSYNC_EVEN/ODD or FRAMEDONE2 interrupts + */ + omap_hwmod_write(irq_mask, oh, DISPC_IRQSTATUS); + + /* disable LCD and TV managers */ + v = omap_hwmod_read(oh, DISPC_CONTROL); + v &= ~(LCD_EN_MASK | DIGIT_EN_MASK); + omap_hwmod_write(v, oh, DISPC_CONTROL); + + /* disable LCD2 manager */ + if (da->manager_count > 2) { + v = omap_hwmod_read(oh, DISPC_CONTROL2); + v &= ~LCD_EN_MASK; + omap_hwmod_write(v, oh, DISPC_CONTROL2); + } + + i = 0; + while ((omap_hwmod_read(oh, DISPC_IRQSTATUS) & irq_mask) != + irq_mask) { + i++; + if (i > FRAMEDONE_IRQ_TIMEOUT) { + pr_err("didn't get FRAMEDONE1/2 or TV interrupt\n"); + break; + } + mdelay(1); + } +} + +#define MAX_MODULE_SOFTRESET_WAIT 10000 +int omap_dss_reset(struct omap_hwmod *oh) +{ + struct omap_hwmod_opt_clk *oc; + int c = 0; + int i, r; + + if (!(oh->class->sysc->sysc_flags & SYSS_HAS_RESET_STATUS)) { + pr_err("dss_core: hwmod data doesn't contain reset data\n"); + return -EINVAL; + } + + for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++) + if (oc->_clk) + clk_enable(oc->_clk); + + dispc_disable_outputs(); + + /* clear SDI registers */ + if (cpu_is_omap3430()) { + omap_hwmod_write(0x0, oh, DSS_SDI_CONTROL); + omap_hwmod_write(0x0, oh, DSS_PLL_CONTROL); + } + + /* + * clear DSS_CONTROL register to switch DSS clock sources to + * PRCM clock, if any + */ + omap_hwmod_write(0x0, oh, DSS_CONTROL); + + omap_test_timeout((omap_hwmod_read(oh, oh->class->sysc->syss_offs) + & SYSS_RESETDONE_MASK), + MAX_MODULE_SOFTRESET_WAIT, c); + + if (c == MAX_MODULE_SOFTRESET_WAIT) + pr_warning("dss_core: waiting for reset to finish failed\n"); + else + pr_debug("dss_core: softreset done\n"); + + for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++) + if (oc->_clk) + clk_disable(oc->_clk); + + r = (c == MAX_MODULE_SOFTRESET_WAIT) ? -ETIMEDOUT : 0; + + return r; +} diff --git a/arch/arm/mach-omap2/display.h b/arch/arm/mach-omap2/display.h new file mode 100644 index 000000000000..b871b017b352 --- /dev/null +++ b/arch/arm/mach-omap2/display.h @@ -0,0 +1,29 @@ +/* + * display.h - OMAP2+ integration-specific DSS header + * + * Copyright (C) 2011 Texas Instruments, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef __ARCH_ARM_MACH_OMAP2_DISPLAY_H +#define __ARCH_ARM_MACH_OMAP2_DISPLAY_H + +#include <linux/kernel.h> + +struct omap_dss_dispc_dev_attr { + u8 manager_count; + bool has_framedonetv_irq; +}; + +#endif diff --git a/arch/arm/mach-omap2/io.h b/arch/arm/mach-omap2/io.h deleted file mode 100644 index e69de29bb2d1..000000000000 --- a/arch/arm/mach-omap2/io.h +++ /dev/null diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c index 6b3088db83b7..207a2ff9a8c4 100644 --- a/arch/arm/mach-omap2/omap_hwmod.c +++ b/arch/arm/mach-omap2/omap_hwmod.c @@ -749,7 +749,7 @@ static int _count_mpu_irqs(struct omap_hwmod *oh) ohii = &oh->mpu_irqs[i++]; } while (ohii->irq != -1); - return i; + return i-1; } /** @@ -772,7 +772,7 @@ static int _count_sdma_reqs(struct omap_hwmod *oh) ohdi = &oh->sdma_reqs[i++]; } while (ohdi->dma_req != -1); - return i; + return i-1; } /** @@ -795,7 +795,7 @@ static int _count_ocp_if_addr_spaces(struct omap_hwmod_ocp_if *os) mem = &os->addr[i++]; } while (mem->pa_start != mem->pa_end); - return i; + return i-1; } /** diff --git a/arch/arm/mach-omap2/omap_hwmod_2420_data.c b/arch/arm/mach-omap2/omap_hwmod_2420_data.c index 6d7206213525..a5409ce3f323 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2420_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2420_data.c @@ -875,6 +875,10 @@ static struct omap_hwmod_ocp_if *omap2420_dss_slaves[] = { }; static struct omap_hwmod_opt_clk dss_opt_clks[] = { + /* + * The DSS HW needs all DSS clocks enabled during reset. The dss_core + * driver does not use these clocks. + */ { .role = "tv_clk", .clk = "dss_54m_fck" }, { .role = "sys_clk", .clk = "dss2_fck" }, }; @@ -899,7 +903,7 @@ static struct omap_hwmod omap2420_dss_core_hwmod = { .slaves_cnt = ARRAY_SIZE(omap2420_dss_slaves), .masters = omap2420_dss_masters, .masters_cnt = ARRAY_SIZE(omap2420_dss_masters), - .flags = HWMOD_NO_IDLEST, + .flags = HWMOD_NO_IDLEST | HWMOD_CONTROL_OPT_CLKS_IN_RESET, }; /* l4_core -> dss_dispc */ @@ -939,6 +943,7 @@ static struct omap_hwmod omap2420_dss_dispc_hwmod = { .slaves = omap2420_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap2420_dss_dispc_slaves), .flags = HWMOD_NO_IDLEST, + .dev_attr = &omap2_3_dss_dispc_dev_attr }; /* l4_core -> dss_rfbi */ @@ -961,6 +966,10 @@ static struct omap_hwmod_ocp_if *omap2420_dss_rfbi_slaves[] = { &omap2420_l4_core__dss_rfbi, }; +static struct omap_hwmod_opt_clk dss_rfbi_opt_clks[] = { + { .role = "ick", .clk = "dss_ick" }, +}; + static struct omap_hwmod omap2420_dss_rfbi_hwmod = { .name = "dss_rfbi", .class = &omap2_rfbi_hwmod_class, @@ -972,6 +981,8 @@ static struct omap_hwmod omap2420_dss_rfbi_hwmod = { .module_offs = CORE_MOD, }, }, + .opt_clks = dss_rfbi_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_rfbi_opt_clks), .slaves = omap2420_dss_rfbi_slaves, .slaves_cnt = ARRAY_SIZE(omap2420_dss_rfbi_slaves), .flags = HWMOD_NO_IDLEST, @@ -981,7 +992,7 @@ static struct omap_hwmod omap2420_dss_rfbi_hwmod = { static struct omap_hwmod_ocp_if omap2420_l4_core__dss_venc = { .master = &omap2420_l4_core_hwmod, .slave = &omap2420_dss_venc_hwmod, - .clk = "dss_54m_fck", + .clk = "dss_ick", .addr = omap2_dss_venc_addrs, .fw = { .omap2 = { @@ -1001,7 +1012,7 @@ static struct omap_hwmod_ocp_if *omap2420_dss_venc_slaves[] = { static struct omap_hwmod omap2420_dss_venc_hwmod = { .name = "dss_venc", .class = &omap2_venc_hwmod_class, - .main_clk = "dss1_fck", + .main_clk = "dss_54m_fck", .prcm = { .omap2 = { .prcm_reg_id = 1, diff --git a/arch/arm/mach-omap2/omap_hwmod_2430_data.c b/arch/arm/mach-omap2/omap_hwmod_2430_data.c index a2580d01c3ff..c4f56cb60d7d 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2430_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2430_data.c @@ -942,6 +942,10 @@ static struct omap_hwmod_ocp_if *omap2430_dss_slaves[] = { }; static struct omap_hwmod_opt_clk dss_opt_clks[] = { + /* + * The DSS HW needs all DSS clocks enabled during reset. The dss_core + * driver does not use these clocks. + */ { .role = "tv_clk", .clk = "dss_54m_fck" }, { .role = "sys_clk", .clk = "dss2_fck" }, }; @@ -966,7 +970,7 @@ static struct omap_hwmod omap2430_dss_core_hwmod = { .slaves_cnt = ARRAY_SIZE(omap2430_dss_slaves), .masters = omap2430_dss_masters, .masters_cnt = ARRAY_SIZE(omap2430_dss_masters), - .flags = HWMOD_NO_IDLEST, + .flags = HWMOD_NO_IDLEST | HWMOD_CONTROL_OPT_CLKS_IN_RESET, }; /* l4_core -> dss_dispc */ @@ -1000,6 +1004,7 @@ static struct omap_hwmod omap2430_dss_dispc_hwmod = { .slaves = omap2430_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap2430_dss_dispc_slaves), .flags = HWMOD_NO_IDLEST, + .dev_attr = &omap2_3_dss_dispc_dev_attr }; /* l4_core -> dss_rfbi */ @@ -1016,6 +1021,10 @@ static struct omap_hwmod_ocp_if *omap2430_dss_rfbi_slaves[] = { &omap2430_l4_core__dss_rfbi, }; +static struct omap_hwmod_opt_clk dss_rfbi_opt_clks[] = { + { .role = "ick", .clk = "dss_ick" }, +}; + static struct omap_hwmod omap2430_dss_rfbi_hwmod = { .name = "dss_rfbi", .class = &omap2_rfbi_hwmod_class, @@ -1027,6 +1036,8 @@ static struct omap_hwmod omap2430_dss_rfbi_hwmod = { .module_offs = CORE_MOD, }, }, + .opt_clks = dss_rfbi_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_rfbi_opt_clks), .slaves = omap2430_dss_rfbi_slaves, .slaves_cnt = ARRAY_SIZE(omap2430_dss_rfbi_slaves), .flags = HWMOD_NO_IDLEST, @@ -1036,7 +1047,7 @@ static struct omap_hwmod omap2430_dss_rfbi_hwmod = { static struct omap_hwmod_ocp_if omap2430_l4_core__dss_venc = { .master = &omap2430_l4_core_hwmod, .slave = &omap2430_dss_venc_hwmod, - .clk = "dss_54m_fck", + .clk = "dss_ick", .addr = omap2_dss_venc_addrs, .flags = OCPIF_SWSUP_IDLE, .user = OCP_USER_MPU | OCP_USER_SDMA, @@ -1050,7 +1061,7 @@ static struct omap_hwmod_ocp_if *omap2430_dss_venc_slaves[] = { static struct omap_hwmod omap2430_dss_venc_hwmod = { .name = "dss_venc", .class = &omap2_venc_hwmod_class, - .main_clk = "dss1_fck", + .main_clk = "dss_54m_fck", .prcm = { .omap2 = { .prcm_reg_id = 1, diff --git a/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c b/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c index c451729d289a..c11273da5dcc 100644 --- a/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_2xxx_3xxx_ipblock_data.c @@ -11,6 +11,7 @@ #include <plat/omap_hwmod.h> #include <plat/serial.h> #include <plat/dma.h> +#include <plat/common.h> #include <mach/irqs.h> @@ -43,13 +44,15 @@ static struct omap_hwmod_class_sysconfig omap2_dss_sysc = { .rev_offs = 0x0000, .sysc_offs = 0x0010, .syss_offs = 0x0014, - .sysc_flags = (SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE), + .sysc_flags = (SYSC_HAS_SOFTRESET | SYSC_HAS_AUTOIDLE | + SYSS_HAS_RESET_STATUS), .sysc_fields = &omap_hwmod_sysc_type1, }; struct omap_hwmod_class omap2_dss_hwmod_class = { .name = "dss", .sysc = &omap2_dss_sysc, + .reset = omap_dss_reset, }; /* diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index bc9035ec87fc..7f8915ad5099 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -1369,9 +1369,14 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_slaves[] = { }; static struct omap_hwmod_opt_clk dss_opt_clks[] = { - { .role = "tv_clk", .clk = "dss_tv_fck" }, - { .role = "video_clk", .clk = "dss_96m_fck" }, + /* + * The DSS HW needs all DSS clocks enabled during reset. The dss_core + * driver does not use these clocks. + */ { .role = "sys_clk", .clk = "dss2_alwon_fck" }, + { .role = "tv_clk", .clk = "dss_tv_fck" }, + /* required only on OMAP3430 */ + { .role = "tv_dac_clk", .clk = "dss_96m_fck" }, }; static struct omap_hwmod omap3430es1_dss_core_hwmod = { @@ -1394,11 +1399,12 @@ static struct omap_hwmod omap3430es1_dss_core_hwmod = { .slaves_cnt = ARRAY_SIZE(omap3430es1_dss_slaves), .masters = omap3xxx_dss_masters, .masters_cnt = ARRAY_SIZE(omap3xxx_dss_masters), - .flags = HWMOD_NO_IDLEST, + .flags = HWMOD_NO_IDLEST | HWMOD_CONTROL_OPT_CLKS_IN_RESET, }; static struct omap_hwmod omap3xxx_dss_core_hwmod = { .name = "dss_core", + .flags = HWMOD_CONTROL_OPT_CLKS_IN_RESET, .class = &omap2_dss_hwmod_class, .main_clk = "dss1_alwon_fck", /* instead of dss_fck */ .sdma_reqs = omap3xxx_dss_sdma_chs, @@ -1456,6 +1462,7 @@ static struct omap_hwmod omap3xxx_dss_dispc_hwmod = { .slaves = omap3xxx_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_dispc_slaves), .flags = HWMOD_NO_IDLEST, + .dev_attr = &omap2_3_dss_dispc_dev_attr }; /* @@ -1486,6 +1493,7 @@ static struct omap_hwmod_addr_space omap3xxx_dss_dsi1_addrs[] = { static struct omap_hwmod_ocp_if omap3xxx_l4_core__dss_dsi1 = { .master = &omap3xxx_l4_core_hwmod, .slave = &omap3xxx_dss_dsi1_hwmod, + .clk = "dss_ick", .addr = omap3xxx_dss_dsi1_addrs, .fw = { .omap2 = { @@ -1502,6 +1510,10 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_dsi1_slaves[] = { &omap3xxx_l4_core__dss_dsi1, }; +static struct omap_hwmod_opt_clk dss_dsi1_opt_clks[] = { + { .role = "sys_clk", .clk = "dss2_alwon_fck" }, +}; + static struct omap_hwmod omap3xxx_dss_dsi1_hwmod = { .name = "dss_dsi1", .class = &omap3xxx_dsi_hwmod_class, @@ -1514,6 +1526,8 @@ static struct omap_hwmod omap3xxx_dss_dsi1_hwmod = { .module_offs = OMAP3430_DSS_MOD, }, }, + .opt_clks = dss_dsi1_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_dsi1_opt_clks), .slaves = omap3xxx_dss_dsi1_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_dsi1_slaves), .flags = HWMOD_NO_IDLEST, @@ -1540,6 +1554,10 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_rfbi_slaves[] = { &omap3xxx_l4_core__dss_rfbi, }; +static struct omap_hwmod_opt_clk dss_rfbi_opt_clks[] = { + { .role = "ick", .clk = "dss_ick" }, +}; + static struct omap_hwmod omap3xxx_dss_rfbi_hwmod = { .name = "dss_rfbi", .class = &omap2_rfbi_hwmod_class, @@ -1551,6 +1569,8 @@ static struct omap_hwmod omap3xxx_dss_rfbi_hwmod = { .module_offs = OMAP3430_DSS_MOD, }, }, + .opt_clks = dss_rfbi_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_rfbi_opt_clks), .slaves = omap3xxx_dss_rfbi_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_rfbi_slaves), .flags = HWMOD_NO_IDLEST, @@ -1560,7 +1580,7 @@ static struct omap_hwmod omap3xxx_dss_rfbi_hwmod = { static struct omap_hwmod_ocp_if omap3xxx_l4_core__dss_venc = { .master = &omap3xxx_l4_core_hwmod, .slave = &omap3xxx_dss_venc_hwmod, - .clk = "dss_tv_fck", + .clk = "dss_ick", .addr = omap2_dss_venc_addrs, .fw = { .omap2 = { @@ -1578,10 +1598,15 @@ static struct omap_hwmod_ocp_if *omap3xxx_dss_venc_slaves[] = { &omap3xxx_l4_core__dss_venc, }; +static struct omap_hwmod_opt_clk dss_venc_opt_clks[] = { + /* required only on OMAP3430 */ + { .role = "tv_dac_clk", .clk = "dss_96m_fck" }, +}; + static struct omap_hwmod omap3xxx_dss_venc_hwmod = { .name = "dss_venc", .class = &omap2_venc_hwmod_class, - .main_clk = "dss1_alwon_fck", + .main_clk = "dss_tv_fck", .prcm = { .omap2 = { .prcm_reg_id = 1, @@ -1589,6 +1614,8 @@ static struct omap_hwmod omap3xxx_dss_venc_hwmod = { .module_offs = OMAP3430_DSS_MOD, }, }, + .opt_clks = dss_venc_opt_clks, + .opt_clks_cnt = ARRAY_SIZE(dss_venc_opt_clks), .slaves = omap3xxx_dss_venc_slaves, .slaves_cnt = ARRAY_SIZE(omap3xxx_dss_venc_slaves), .flags = HWMOD_NO_IDLEST, diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 7695e5d43316..daaf165af696 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -30,6 +30,7 @@ #include <plat/mmc.h> #include <plat/i2c.h> #include <plat/dmtimer.h> +#include <plat/common.h> #include "omap_hwmod_common_data.h" @@ -1187,6 +1188,7 @@ static struct omap_hwmod_class_sysconfig omap44xx_dss_sysc = { static struct omap_hwmod_class omap44xx_dss_hwmod_class = { .name = "dss", .sysc = &omap44xx_dss_sysc, + .reset = omap_dss_reset, }; /* dss */ @@ -1240,12 +1242,12 @@ static struct omap_hwmod_ocp_if *omap44xx_dss_slaves[] = { static struct omap_hwmod_opt_clk dss_opt_clks[] = { { .role = "sys_clk", .clk = "dss_sys_clk" }, { .role = "tv_clk", .clk = "dss_tv_clk" }, - { .role = "dss_clk", .clk = "dss_dss_clk" }, - { .role = "video_clk", .clk = "dss_48mhz_clk" }, + { .role = "hdmi_clk", .clk = "dss_48mhz_clk" }, }; static struct omap_hwmod omap44xx_dss_hwmod = { .name = "dss_core", + .flags = HWMOD_CONTROL_OPT_CLKS_IN_RESET, .class = &omap44xx_dss_hwmod_class, .clkdm_name = "l3_dss_clkdm", .main_clk = "dss_dss_clk", @@ -1325,6 +1327,11 @@ static struct omap_hwmod_addr_space omap44xx_dss_dispc_addrs[] = { { } }; +static struct omap_dss_dispc_dev_attr omap44xx_dss_dispc_dev_attr = { + .manager_count = 3, + .has_framedonetv_irq = 1 +}; + /* l4_per -> dss_dispc */ static struct omap_hwmod_ocp_if omap44xx_l4_per__dss_dispc = { .master = &omap44xx_l4_per_hwmod, @@ -1340,12 +1347,6 @@ static struct omap_hwmod_ocp_if *omap44xx_dss_dispc_slaves[] = { &omap44xx_l4_per__dss_dispc, }; -static struct omap_hwmod_opt_clk dss_dispc_opt_clks[] = { - { .role = "sys_clk", .clk = "dss_sys_clk" }, - { .role = "tv_clk", .clk = "dss_tv_clk" }, - { .role = "hdmi_clk", .clk = "dss_48mhz_clk" }, -}; - static struct omap_hwmod omap44xx_dss_dispc_hwmod = { .name = "dss_dispc", .class = &omap44xx_dispc_hwmod_class, @@ -1359,10 +1360,9 @@ static struct omap_hwmod omap44xx_dss_dispc_hwmod = { .context_offs = OMAP4_RM_DSS_DSS_CONTEXT_OFFSET, }, }, - .opt_clks = dss_dispc_opt_clks, - .opt_clks_cnt = ARRAY_SIZE(dss_dispc_opt_clks), .slaves = omap44xx_dss_dispc_slaves, .slaves_cnt = ARRAY_SIZE(omap44xx_dss_dispc_slaves), + .dev_attr = &omap44xx_dss_dispc_dev_attr }; /* @@ -1624,7 +1624,7 @@ static struct omap_hwmod omap44xx_dss_hdmi_hwmod = { .clkdm_name = "l3_dss_clkdm", .mpu_irqs = omap44xx_dss_hdmi_irqs, .sdma_reqs = omap44xx_dss_hdmi_sdma_reqs, - .main_clk = "dss_dss_clk", + .main_clk = "dss_48mhz_clk", .prcm = { .omap4 = { .clkctrl_offs = OMAP4_CM_DSS_DSS_CLKCTRL_OFFSET, @@ -1785,7 +1785,7 @@ static struct omap_hwmod omap44xx_dss_venc_hwmod = { .name = "dss_venc", .class = &omap44xx_venc_hwmod_class, .clkdm_name = "l3_dss_clkdm", - .main_clk = "dss_dss_clk", + .main_clk = "dss_tv_clk", .prcm = { .omap4 = { .clkctrl_offs = OMAP4_CM_DSS_DSS_CLKCTRL_OFFSET, diff --git a/arch/arm/mach-omap2/omap_hwmod_common_data.c b/arch/arm/mach-omap2/omap_hwmod_common_data.c index de832ebc93a9..51e5418899fb 100644 --- a/arch/arm/mach-omap2/omap_hwmod_common_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_common_data.c @@ -49,3 +49,7 @@ struct omap_hwmod_sysc_fields omap_hwmod_sysc_type2 = { .srst_shift = SYSC_TYPE2_SOFTRESET_SHIFT, }; +struct omap_dss_dispc_dev_attr omap2_3_dss_dispc_dev_attr = { + .manager_count = 2, + .has_framedonetv_irq = 0 +}; diff --git a/arch/arm/mach-omap2/omap_hwmod_common_data.h b/arch/arm/mach-omap2/omap_hwmod_common_data.h index 39a7c37f4587..ad5d8f04c0b8 100644 --- a/arch/arm/mach-omap2/omap_hwmod_common_data.h +++ b/arch/arm/mach-omap2/omap_hwmod_common_data.h @@ -16,6 +16,8 @@ #include <plat/omap_hwmod.h> +#include "display.h" + /* Common address space across OMAP2xxx */ extern struct omap_hwmod_addr_space omap2xxx_uart1_addr_space[]; extern struct omap_hwmod_addr_space omap2xxx_uart2_addr_space[]; @@ -111,4 +113,6 @@ extern struct omap_hwmod_class omap2xxx_dma_hwmod_class; extern struct omap_hwmod_class omap2xxx_mailbox_hwmod_class; extern struct omap_hwmod_class omap2xxx_mcspi_class; +extern struct omap_dss_dispc_dev_attr omap2_3_dss_dispc_dev_attr; + #endif diff --git a/arch/arm/mach-omap2/omap_l3_noc.c b/arch/arm/mach-omap2/omap_l3_noc.c index 6a66aa5e2a5b..d15225ff5c49 100644 --- a/arch/arm/mach-omap2/omap_l3_noc.c +++ b/arch/arm/mach-omap2/omap_l3_noc.c @@ -237,7 +237,7 @@ static int __devexit omap4_l3_remove(struct platform_device *pdev) static const struct of_device_id l3_noc_match[] = { {.compatible = "ti,omap4-l3-noc", }, {}, -} +}; MODULE_DEVICE_TABLE(of, l3_noc_match); #else #define l3_noc_match NULL diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 1e79bdf313e3..00bff46ca48b 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -24,6 +24,7 @@ #include "powerdomain.h" #include "clockdomain.h" #include "pm.h" +#include "twl-common.h" static struct omap_device_pm_latency *pm_lats; @@ -226,11 +227,8 @@ postcore_initcall(omap2_common_pm_init); static int __init omap2_common_pm_late_init(void) { - /* Init the OMAP TWL parameters */ - omap3_twl_init(); - omap4_twl_init(); - /* Init the voltage layer */ + omap_pmic_late_init(); omap_voltage_late_init(); /* Initialize the voltages */ diff --git a/arch/arm/mach-omap2/smartreflex.c b/arch/arm/mach-omap2/smartreflex.c index 6a4f6839a7d9..cf246b39bac7 100644 --- a/arch/arm/mach-omap2/smartreflex.c +++ b/arch/arm/mach-omap2/smartreflex.c @@ -139,7 +139,7 @@ static irqreturn_t sr_interrupt(int irq, void *data) sr_write_reg(sr_info, ERRCONFIG_V1, status); } else if (sr_info->ip_type == SR_TYPE_V2) { /* Read the status bits */ - sr_read_reg(sr_info, IRQSTATUS); + status = sr_read_reg(sr_info, IRQSTATUS); /* Clear them by writing back */ sr_write_reg(sr_info, IRQSTATUS, status); diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 522435772168..10b20c652e5d 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -30,6 +30,7 @@ #include <plat/usb.h> #include "twl-common.h" +#include "pm.h" static struct i2c_board_info __initdata pmic_i2c_board_info = { .addr = 0x48, @@ -48,6 +49,16 @@ void __init omap_pmic_init(int bus, u32 clkrate, omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1); } +void __init omap_pmic_late_init(void) +{ + /* Init the OMAP TWL parameters (if PMIC has been registerd) */ + if (!pmic_i2c_board_info.irq) + return; + + omap3_twl_init(); + omap4_twl_init(); +} + #if defined(CONFIG_ARCH_OMAP3) static struct twl4030_usb_data omap3_usb_pdata = { .usb_mode = T2_USB_MODE_ULPI, diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h index 5e83a5bd37fb..275dde8cb27a 100644 --- a/arch/arm/mach-omap2/twl-common.h +++ b/arch/arm/mach-omap2/twl-common.h @@ -1,6 +1,8 @@ #ifndef __OMAP_PMIC_COMMON__ #define __OMAP_PMIC_COMMON__ +#include <plat/irqs.h> + #define TWL_COMMON_PDATA_USB (1 << 0) #define TWL_COMMON_PDATA_BCI (1 << 1) #define TWL_COMMON_PDATA_MADC (1 << 2) @@ -30,6 +32,7 @@ struct twl4030_platform_data; void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq, struct twl4030_platform_data *pmic_data); +void omap_pmic_late_init(void); static inline void omap2_pmic_init(const char *pmic_type, struct twl4030_platform_data *pmic_data) diff --git a/arch/arm/mach-prima2/pm.c b/arch/arm/mach-prima2/pm.c index cb53160f6c5d..26ebb57719df 100644 --- a/arch/arm/mach-prima2/pm.c +++ b/arch/arm/mach-prima2/pm.c @@ -9,6 +9,7 @@ #include <linux/kernel.h> #include <linux/suspend.h> #include <linux/slab.h> +#include <linux/module.h> #include <linux/of.h> #include <linux/of_address.h> #include <linux/of_device.h> diff --git a/arch/arm/mach-prima2/prima2.c b/arch/arm/mach-prima2/prima2.c index ef555c041962..a12b689a8702 100644 --- a/arch/arm/mach-prima2/prima2.c +++ b/arch/arm/mach-prima2/prima2.c @@ -8,6 +8,7 @@ #include <linux/init.h> #include <linux/kernel.h> +#include <asm/sizes.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> #include <linux/of.h> diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c index fc0b8544e174..4b81f59a4cba 100644 --- a/arch/arm/mach-pxa/balloon3.c +++ b/arch/arm/mach-pxa/balloon3.c @@ -307,7 +307,7 @@ static inline void balloon3_mmc_init(void) {} /****************************************************************************** * USB Gadget ******************************************************************************/ -#if defined(CONFIG_USB_GADGET_PXA27X)||defined(CONFIG_USB_GADGET_PXA27X_MODULE) +#if defined(CONFIG_USB_PXA27X)||defined(CONFIG_USB_PXA27X_MODULE) static void balloon3_udc_command(int cmd) { if (cmd == PXA2XX_UDC_CMD_CONNECT) diff --git a/arch/arm/mach-pxa/colibri-pxa320.c b/arch/arm/mach-pxa/colibri-pxa320.c index 692e1ffc5586..d23b92b80488 100644 --- a/arch/arm/mach-pxa/colibri-pxa320.c +++ b/arch/arm/mach-pxa/colibri-pxa320.c @@ -146,7 +146,7 @@ static void __init colibri_pxa320_init_eth(void) static inline void __init colibri_pxa320_init_eth(void) {} #endif /* CONFIG_AX88796 */ -#if defined(CONFIG_USB_GADGET_PXA27X)||defined(CONFIG_USB_GADGET_PXA27X_MODULE) +#if defined(CONFIG_USB_PXA27X)||defined(CONFIG_USB_PXA27X_MODULE) static struct gpio_vbus_mach_info colibri_pxa320_gpio_vbus_info = { .gpio_vbus = mfp_to_gpio(MFP_PIN_GPIO96), .gpio_pullup = -1, diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c index 9c8208ca0415..ffdd70dad327 100644 --- a/arch/arm/mach-pxa/gumstix.c +++ b/arch/arm/mach-pxa/gumstix.c @@ -106,7 +106,7 @@ static void __init gumstix_mmc_init(void) } #endif -#ifdef CONFIG_USB_GADGET_PXA25X +#ifdef CONFIG_USB_PXA25X static struct gpio_vbus_mach_info gumstix_udc_info = { .gpio_vbus = GPIO_GUMSTIX_USB_GPIOn, .gpio_pullup = GPIO_GUMSTIX_USB_GPIOx, diff --git a/arch/arm/mach-pxa/include/mach/palm27x.h b/arch/arm/mach-pxa/include/mach/palm27x.h index f80bbe246afe..d4eac3d6ffb5 100644 --- a/arch/arm/mach-pxa/include/mach/palm27x.h +++ b/arch/arm/mach-pxa/include/mach/palm27x.h @@ -37,8 +37,8 @@ extern void __init palm27x_lcd_init(int power, #define palm27x_lcd_init(power, mode) do {} while (0) #endif -#if defined(CONFIG_USB_GADGET_PXA27X) || \ - defined(CONFIG_USB_GADGET_PXA27X_MODULE) +#if defined(CONFIG_USB_PXA27X) || \ + defined(CONFIG_USB_PXA27X_MODULE) extern void __init palm27x_udc_init(int vbus, int pullup, int vbus_inverted); #else diff --git a/arch/arm/mach-pxa/palm27x.c b/arch/arm/mach-pxa/palm27x.c index 325c245c0a0d..fbc10d7b95d1 100644 --- a/arch/arm/mach-pxa/palm27x.c +++ b/arch/arm/mach-pxa/palm27x.c @@ -164,8 +164,8 @@ void __init palm27x_lcd_init(int power, struct pxafb_mode_info *mode) /****************************************************************************** * USB Gadget ******************************************************************************/ -#if defined(CONFIG_USB_GADGET_PXA27X) || \ - defined(CONFIG_USB_GADGET_PXA27X_MODULE) +#if defined(CONFIG_USB_PXA27X) || \ + defined(CONFIG_USB_PXA27X_MODULE) static struct gpio_vbus_mach_info palm27x_udc_info = { .gpio_vbus_inverted = 1, }; diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c index 6ec7caefb37c..2c24c67fd92b 100644 --- a/arch/arm/mach-pxa/palmtc.c +++ b/arch/arm/mach-pxa/palmtc.c @@ -338,7 +338,7 @@ static inline void palmtc_mkp_init(void) {} /****************************************************************************** * UDC ******************************************************************************/ -#if defined(CONFIG_USB_GADGET_PXA25X)||defined(CONFIG_USB_GADGET_PXA25X_MODULE) +#if defined(CONFIG_USB_PXA25X)||defined(CONFIG_USB_PXA25X_MODULE) static struct gpio_vbus_mach_info palmtc_udc_info = { .gpio_vbus = GPIO_NR_PALMTC_USB_DETECT_N, .gpio_vbus_inverted = 1, diff --git a/arch/arm/mach-pxa/vpac270.c b/arch/arm/mach-pxa/vpac270.c index a7539a6ed1ff..ca0c6615028c 100644 --- a/arch/arm/mach-pxa/vpac270.c +++ b/arch/arm/mach-pxa/vpac270.c @@ -343,7 +343,7 @@ static inline void vpac270_uhc_init(void) {} /****************************************************************************** * USB Gadget ******************************************************************************/ -#if defined(CONFIG_USB_GADGET_PXA27X)||defined(CONFIG_USB_GADGET_PXA27X_MODULE) +#if defined(CONFIG_USB_PXA27X)||defined(CONFIG_USB_PXA27X_MODULE) static struct gpio_vbus_mach_info vpac270_gpio_vbus_info = { .gpio_vbus = GPIO41_VPAC270_UDC_DETECT, .gpio_pullup = -1, diff --git a/arch/arm/mach-s3c64xx/dev-spi.c b/arch/arm/mach-s3c64xx/dev-spi.c index 5e6b42089eb4..3341fd118723 100644 --- a/arch/arm/mach-s3c64xx/dev-spi.c +++ b/arch/arm/mach-s3c64xx/dev-spi.c @@ -10,6 +10,7 @@ #include <linux/kernel.h> #include <linux/string.h> +#include <linux/export.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/gpio.h> diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c index 66668565ee75..f208154b1382 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c @@ -8,7 +8,7 @@ * published by the Free Software Foundation. */ -#include <linux/module.h> +#include <linux/export.h> #include <linux/interrupt.h> #include <linux/i2c.h> diff --git a/arch/arm/mach-s3c64xx/s3c6400.c b/arch/arm/mach-s3c64xx/s3c6400.c index 7a3bc32df425..51c00f2453c6 100644 --- a/arch/arm/mach-s3c64xx/s3c6400.c +++ b/arch/arm/mach-s3c64xx/s3c6400.c @@ -70,7 +70,7 @@ void __init s3c6400_init_irq(void) s3c64xx_init_irq(~0 & ~(0xf << 5), ~0); } -struct sysdev_class s3c6400_sysclass = { +static struct sysdev_class s3c6400_sysclass = { .name = "s3c6400-core", }; diff --git a/arch/arm/mach-s3c64xx/setup-fb-24bpp.c b/arch/arm/mach-s3c64xx/setup-fb-24bpp.c index 83d2afb79e9f..2cf80026c58d 100644 --- a/arch/arm/mach-s3c64xx/setup-fb-24bpp.c +++ b/arch/arm/mach-s3c64xx/setup-fb-24bpp.c @@ -20,7 +20,7 @@ #include <plat/fb.h> #include <plat/gpio-cfg.h> -extern void s3c64xx_fb_gpio_setup_24bpp(void) +void s3c64xx_fb_gpio_setup_24bpp(void) { s3c_gpio_cfgrange_nopull(S3C64XX_GPI(0), 16, S3C_GPIO_SFN(2)); s3c_gpio_cfgrange_nopull(S3C64XX_GPJ(0), 12, S3C_GPIO_SFN(2)); diff --git a/arch/arm/mach-sa1100/Makefile.boot b/arch/arm/mach-sa1100/Makefile.boot index 5a616f6e5612..f7951aa04562 100644 --- a/arch/arm/mach-sa1100/Makefile.boot +++ b/arch/arm/mach-sa1100/Makefile.boot @@ -1,5 +1,5 @@ -ifeq ($(CONFIG_ARCH_SA1100),y) - zreladdr-$(CONFIG_SA1111) += 0xc0208000 +ifeq ($(CONFIG_SA1111),y) + zreladdr-y += 0xc0208000 else zreladdr-y += 0xc0008000 endif diff --git a/arch/arm/mm/cache-l2x0.c b/arch/arm/mm/cache-l2x0.c index 8ac9e9f84790..b1e192ba8c24 100644 --- a/arch/arm/mm/cache-l2x0.c +++ b/arch/arm/mm/cache-l2x0.c @@ -61,7 +61,7 @@ static inline void cache_sync(void) { void __iomem *base = l2x0_base; -#ifdef CONFIG_ARM_ERRATA_753970 +#ifdef CONFIG_PL310_ERRATA_753970 /* write to an unmmapped register */ writel_relaxed(0, base + L2X0_DUMMY_REG); #else diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index e4e7f6cba1ab..1aa664a1999f 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -168,7 +168,7 @@ static int __init consistent_init(void) pte_t *pte; int i = 0; unsigned long base = consistent_base; - unsigned long num_ptes = (CONSISTENT_END - base) >> PGDIR_SHIFT; + unsigned long num_ptes = (CONSISTENT_END - base) >> PMD_SHIFT; consistent_pte = kmalloc(num_ptes * sizeof(pte_t), GFP_KERNEL); if (!consistent_pte) { @@ -332,6 +332,15 @@ __dma_alloc(struct device *dev, size_t size, dma_addr_t *handle, gfp_t gfp, struct page *page; void *addr; + /* + * Following is a work-around (a.k.a. hack) to prevent pages + * with __GFP_COMP being passed to split_page() which cannot + * handle them. The real problem is that this flag probably + * should be 0 on ARM as it is not supported on this + * platform; see CONFIG_HUGETLBFS. + */ + gfp &= ~(__GFP_COMP); + *handle = ~0; size = PAGE_ALIGN(size); diff --git a/arch/arm/mm/mmap.c b/arch/arm/mm/mmap.c index 74be05f3e03a..44b628e4d6ea 100644 --- a/arch/arm/mm/mmap.c +++ b/arch/arm/mm/mmap.c @@ -9,8 +9,7 @@ #include <linux/io.h> #include <linux/personality.h> #include <linux/random.h> -#include <asm/cputype.h> -#include <asm/system.h> +#include <asm/cachetype.h> #define COLOUR_ALIGN(addr,pgoff) \ ((((addr)+SHMLBA-1)&~(SHMLBA-1)) + \ @@ -32,25 +31,15 @@ arch_get_unmapped_area(struct file *filp, unsigned long addr, struct mm_struct *mm = current->mm; struct vm_area_struct *vma; unsigned long start_addr; -#if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K) - unsigned int cache_type; - int do_align = 0, aliasing = 0; + int do_align = 0; + int aliasing = cache_is_vipt_aliasing(); /* * We only need to do colour alignment if either the I or D - * caches alias. This is indicated by bits 9 and 21 of the - * cache type register. + * caches alias. */ - cache_type = read_cpuid_cachetype(); - if (cache_type != read_cpuid_id()) { - aliasing = (cache_type | cache_type >> 12) & (1 << 11); - if (aliasing) - do_align = filp || flags & MAP_SHARED; - } -#else -#define do_align 0 -#define aliasing 0 -#endif + if (aliasing) + do_align = filp || (flags & MAP_SHARED); /* * We enforce the MAP_FIXED case. diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h index 83b745a5e1b7..c75f254abd85 100644 --- a/arch/arm/plat-mxc/include/mach/common.h +++ b/arch/arm/plat-mxc/include/mach/common.h @@ -85,7 +85,6 @@ enum mxc_cpu_pwr_mode { }; extern void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode); -extern void (*imx_idle)(void); extern void imx_print_silicon_rev(const char *cpu, int srev); void avic_handle_irq(struct pt_regs *); @@ -133,4 +132,5 @@ extern void imx53_qsb_common_init(void); extern void imx53_smd_common_init(void); extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode); extern void imx6q_pm_init(void); +extern void imx6q_clock_map_io(void); #endif diff --git a/arch/arm/plat-mxc/include/mach/mxc.h b/arch/arm/plat-mxc/include/mach/mxc.h index 00a78193c681..a4d36d601d55 100644 --- a/arch/arm/plat-mxc/include/mach/mxc.h +++ b/arch/arm/plat-mxc/include/mach/mxc.h @@ -50,20 +50,6 @@ #define IMX_CHIP_REVISION_3_3 0x33 #define IMX_CHIP_REVISION_UNKNOWN 0xff -#define IMX_CHIP_REVISION_1_0_STRING "1.0" -#define IMX_CHIP_REVISION_1_1_STRING "1.1" -#define IMX_CHIP_REVISION_1_2_STRING "1.2" -#define IMX_CHIP_REVISION_1_3_STRING "1.3" -#define IMX_CHIP_REVISION_2_0_STRING "2.0" -#define IMX_CHIP_REVISION_2_1_STRING "2.1" -#define IMX_CHIP_REVISION_2_2_STRING "2.2" -#define IMX_CHIP_REVISION_2_3_STRING "2.3" -#define IMX_CHIP_REVISION_3_0_STRING "3.0" -#define IMX_CHIP_REVISION_3_1_STRING "3.1" -#define IMX_CHIP_REVISION_3_2_STRING "3.2" -#define IMX_CHIP_REVISION_3_3_STRING "3.3" -#define IMX_CHIP_REVISION_UNKNOWN_STRING "unknown" - #ifndef __ASSEMBLY__ extern unsigned int __mxc_cpu_type; #endif diff --git a/arch/arm/plat-mxc/include/mach/system.h b/arch/arm/plat-mxc/include/mach/system.h index cf88b3593fba..b9895d250167 100644 --- a/arch/arm/plat-mxc/include/mach/system.h +++ b/arch/arm/plat-mxc/include/mach/system.h @@ -17,14 +17,9 @@ #ifndef __ASM_ARCH_MXC_SYSTEM_H__ #define __ASM_ARCH_MXC_SYSTEM_H__ -extern void (*imx_idle)(void); - static inline void arch_idle(void) { - if (imx_idle != NULL) - (imx_idle)(); - else - cpu_do_idle(); + cpu_do_idle(); } void arch_reset(char mode, const char *cmd); diff --git a/arch/arm/plat-mxc/system.c b/arch/arm/plat-mxc/system.c index 9dad8dcc2ea9..d65fb31a55ca 100644 --- a/arch/arm/plat-mxc/system.c +++ b/arch/arm/plat-mxc/system.c @@ -21,6 +21,7 @@ #include <linux/io.h> #include <linux/err.h> #include <linux/delay.h> +#include <linux/module.h> #include <mach/hardware.h> #include <mach/common.h> @@ -28,8 +29,8 @@ #include <asm/system.h> #include <asm/mach-types.h> -void (*imx_idle)(void) = NULL; void __iomem *(*imx_ioremap)(unsigned long, size_t, unsigned int) = NULL; +EXPORT_SYMBOL_GPL(imx_ioremap); static void __iomem *wdog_base; diff --git a/arch/arm/plat-omap/include/plat/clock.h b/arch/arm/plat-omap/include/plat/clock.h index 197ca03c3f7d..eb73ab40e955 100644 --- a/arch/arm/plat-omap/include/plat/clock.h +++ b/arch/arm/plat-omap/include/plat/clock.h @@ -165,8 +165,8 @@ struct dpll_data { u8 auto_recal_bit; u8 recal_en_bit; u8 recal_st_bit; - u8 flags; # endif + u8 flags; }; #endif diff --git a/arch/arm/plat-omap/include/plat/common.h b/arch/arm/plat-omap/include/plat/common.h index c50df4814f6f..3ff3e36580f2 100644 --- a/arch/arm/plat-omap/include/plat/common.h +++ b/arch/arm/plat-omap/include/plat/common.h @@ -30,6 +30,7 @@ #include <linux/delay.h> #include <plat/i2c.h> +#include <plat/omap_hwmod.h> struct sys_timer; @@ -55,6 +56,8 @@ void am35xx_init_early(void); void ti816x_init_early(void); void omap4430_init_early(void); +extern int omap_dss_reset(struct omap_hwmod *); + void omap_sram_init(void); /* diff --git a/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c b/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c index a9276667c2fb..c7adad0e8de0 100644 --- a/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c +++ b/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c @@ -12,7 +12,7 @@ */ #include <linux/init.h> -#include <linux/module.h> +#include <linux/export.h> #include <linux/interrupt.h> #include <linux/ioport.h> #include <linux/cpufreq.h> diff --git a/arch/arm/plat-s5p/sysmmu.c b/arch/arm/plat-s5p/sysmmu.c index e1cbc728c775..c8bec9c7655d 100644 --- a/arch/arm/plat-s5p/sysmmu.c +++ b/arch/arm/plat-s5p/sysmmu.c @@ -11,6 +11,7 @@ #include <linux/io.h> #include <linux/interrupt.h> #include <linux/platform_device.h> +#include <linux/export.h> #include <asm/pgtable.h> diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/plat-samsung/include/plat/gpio-cfg.h index d48245bb02b3..df8155b9d4d1 100644 --- a/arch/arm/plat-samsung/include/plat/gpio-cfg.h +++ b/arch/arm/plat-samsung/include/plat/gpio-cfg.h @@ -24,6 +24,8 @@ #ifndef __PLAT_GPIO_CFG_H #define __PLAT_GPIO_CFG_H __FILE__ +#include<linux/types.h> + typedef unsigned int __bitwise__ samsung_gpio_pull_t; typedef unsigned int __bitwise__ s5p_gpio_drvstr_t; diff --git a/arch/arm/plat-samsung/pd.c b/arch/arm/plat-samsung/pd.c index efe1d564473e..312b510d86b7 100644 --- a/arch/arm/plat-samsung/pd.c +++ b/arch/arm/plat-samsung/pd.c @@ -11,7 +11,7 @@ */ #include <linux/init.h> -#include <linux/module.h> +#include <linux/export.h> #include <linux/platform_device.h> #include <linux/err.h> #include <linux/pm_runtime.h> diff --git a/arch/arm/plat-samsung/pwm.c b/arch/arm/plat-samsung/pwm.c index dc1185dcf80d..c559d8438c70 100644 --- a/arch/arm/plat-samsung/pwm.c +++ b/arch/arm/plat-samsung/pwm.c @@ -11,7 +11,7 @@ * the Free Software Foundation; either version 2 of the License. */ -#include <linux/module.h> +#include <linux/export.h> #include <linux/kernel.h> #include <linux/platform_device.h> #include <linux/slab.h> diff --git a/arch/arm/tools/mach-types b/arch/arm/tools/mach-types index 5bdeef969847..ccbe16f47227 100644 --- a/arch/arm/tools/mach-types +++ b/arch/arm/tools/mach-types @@ -1123,5 +1123,6 @@ blissc MACH_BLISSC BLISSC 3491 thales_adc MACH_THALES_ADC THALES_ADC 3492 ubisys_p9d_evp MACH_UBISYS_P9D_EVP UBISYS_P9D_EVP 3493 atdgp318 MACH_ATDGP318 ATDGP318 3494 +m28evk MACH_M28EVK M28EVK 3613 smdk4212 MACH_SMDK4212 SMDK4212 3638 smdk4412 MACH_SMDK4412 SMDK4412 3765 |