diff options
Diffstat (limited to 'include/linux/regulator')
| -rw-r--r-- | include/linux/regulator/driver.h | 10 | ||||
| -rw-r--r-- | include/linux/regulator/machine.h | 8 | ||||
| -rw-r--r-- | include/linux/regulator/max8973-regulator.h | 4 |
3 files changed, 22 insertions, 0 deletions
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index fffa688ac3a7..125264f8be93 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -91,6 +91,7 @@ struct regulator_linear_range { * @set_current_limit: Configure a limit for a current-limited regulator. * The driver should select the current closest to max_uA. * @get_current_limit: Get the configured limit for a current-limited regulator. + * @set_input_current_limit: Configure an input limit. * * @set_mode: Set the configured operating mode for the regulator. * @get_mode: Get the configured operating mode for the regulator. @@ -121,6 +122,9 @@ struct regulator_linear_range { * @set_suspend_mode: Set the operating mode for the regulator when the * system is suspended. * + * @set_pull_down: Configure the regulator to pull down when the regulator + * is disabled. + * * This struct describes regulator operations which can be implemented by * regulator chip drivers. */ @@ -142,6 +146,8 @@ struct regulator_ops { int min_uA, int max_uA); int (*get_current_limit) (struct regulator_dev *); + int (*set_input_current_limit) (struct regulator_dev *, int lim_uA); + /* enable/disable regulator */ int (*enable) (struct regulator_dev *); int (*disable) (struct regulator_dev *); @@ -158,6 +164,8 @@ struct regulator_ops { unsigned int old_selector, unsigned int new_selector); + int (*set_soft_start) (struct regulator_dev *); + /* report regulator status ... most other accessors report * control inputs, this reports results of combining inputs * from Linux (and other sources) with the actual load. @@ -187,6 +195,8 @@ struct regulator_ops { /* set regulator suspend operating mode (defined in consumer.h) */ int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode); + + int (*set_pull_down) (struct regulator_dev *); }; /* diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index b07562e082c4..85a3b457de51 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -75,6 +75,8 @@ struct regulator_state { * * @min_uA: Smallest current consumers may set. * @max_uA: Largest current consumers may set. + * @ilim_uA: Maximum input current. + * @system_load: Load that isn't captured by any consumer requests. * * @valid_modes_mask: Mask of modes which may be configured by consumers. * @valid_ops_mask: Operations which may be performed by consumers. @@ -86,6 +88,7 @@ struct regulator_state { * applied. * @apply_uV: Apply the voltage constraint when initialising. * @ramp_disable: Disable ramp delay when initialising or when setting voltage. + * @pull_down: Enable pull down when regulator is disabled. * * @input_uV: Input voltage for regulator when supplied by another regulator. * @@ -111,6 +114,9 @@ struct regulation_constraints { /* current output range (inclusive) - for current control */ int min_uA; int max_uA; + int ilim_uA; + + int system_load; /* valid regulator operating modes for this machine */ unsigned int valid_modes_mask; @@ -138,6 +144,8 @@ struct regulation_constraints { unsigned boot_on:1; /* bootloader/firmware enabled regulator */ unsigned apply_uV:1; /* apply uV constraint if min == max */ unsigned ramp_disable:1; /* disable ramp delay */ + unsigned soft_start:1; /* ramp voltage slowly */ + unsigned pull_down:1; /* pull down resistor when regulator off */ }; /** diff --git a/include/linux/regulator/max8973-regulator.h b/include/linux/regulator/max8973-regulator.h index f8acc052e353..f6a8a16a0d4d 100644 --- a/include/linux/regulator/max8973-regulator.h +++ b/include/linux/regulator/max8973-regulator.h @@ -58,6 +58,9 @@ * control signal from EN input pin. If it is false then * voltage output will be enabled/disabled through EN bit of * device register. + * @enable_gpio: Enable GPIO. If EN pin is controlled through GPIO from host + * then GPIO number can be provided. If no GPIO controlled then + * it should be -1. * @dvs_gpio: GPIO for dvs. It should be -1 if this is tied with fixed logic. * @dvs_def_state: Default state of dvs. 1 if it is high else 0. */ @@ -65,6 +68,7 @@ struct max8973_regulator_platform_data { struct regulator_init_data *reg_init_data; unsigned long control_flags; bool enable_ext_control; + int enable_gpio; int dvs_gpio; unsigned dvs_def_state:1; }; |