summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
* Bluetooth: 6LoWPAN: Fix MAC address universal/local bit handlingJukka Rissanen2014-05-301-30/+35
| | | | | | | | | | | | | | | | | | | | | | | The universal/local bit handling was incorrectly done in the code. So when setting EUI address from BD address we do this: - If BD address type is PUBLIC, then we clear the universal bit in EUI address. If the address type is RANDOM, then the universal bit is set (BT 6lowpan draft chapter 3.2.2) - After this we invert the universal/local bit according to RFC 2464 When figuring out BD address we do the reverse: - Take EUI address from stateless IPv6 address, invert the universal/local bit according to RFC 2464 - If universal bit is 1 in this modified EUI address, then address type is set to RANDOM, otherwise it is PUBLIC Note that 6lowpan_iphc.[ch] does the final toggling of U/L bit before sending or receiving the network packet. Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
* Bluetooth: Fix authentication check for FIPS security levelJohan Hedberg2014-05-301-0/+1
| | | | | | | | | | | When checking whether we need to request authentication or not we should include HCI_SECURITY_FIPS to the levels that always need authentication. This patch fixes check for it in the hci_outgoing_auth_needed() function. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
* Bluetooth: Fix properly ignoring LTKs of unknown typesJohan Hedberg2014-05-301-2/+8
| | | | | | | | | | | | In case there are new LTK types in the future we shouldn't just blindly assume that != MGMT_LTK_UNAUTHENTICATED means that the key is authenticated. This patch adds explicit checks for each allowed key type in the form of a switch statement and skips any key which has an unknown value. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
* Bluetooth: ath3k: no need to set same pipe multiple timesAdam Lee2014-05-271-1/+2
| | | | | | | | Invoking usb_sndbulkpipe() on same pipe for same purpose only once is enough. Signed-off-by: Adam Lee <adam8157@gmail.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: Clearly distinguish mgmt LTK type from authenticated propertyJohan Hedberg2014-05-232-3/+19
| | | | | | | | | | | | | On the mgmt level we have a key type parameter which currently accepts two possible values: 0x00 for unauthenticated and 0x01 for authenticated. However, in the internal struct smp_ltk representation we have an explicit "authenticated" boolean value. To make this distinction clear, add defines for the possible mgmt values and do conversion to and from the internal authenticated value. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Update smp_confirm to return a response codeJohan Hedberg2014-05-201-14/+11
| | | | | | | | | | | Now that smp_confirm() is called "inline" we can have it return a response code and have the sending of it be done in the shared place for command handlers. One exception is when we're entering smp.c from mgmt.c when user space responds to authentication, in which case we still need our own code to call smp_failure(). Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Update smp_random to return a response codeJohan Hedberg2014-05-201-23/+11
| | | | | | | | | Since we're now calling smp_random() "inline" we can have it directly return a response code and have the shared command handler send the response. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Rename smp->smp_flags to smp->flagsJohan Hedberg2014-05-201-19/+18
| | | | | | | | There's no reason to have "smp" in this variable name since it is already part of the SMP struct which provides sufficient context. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Remove unnecessary work structs from SMP codeJohan Hedberg2014-05-201-16/+6
| | | | | | | | | | | | | | | When the SMP code was initially created (mid-2011) parts of the Bluetooth subsystem were still not converted to use workqueues. This meant that the crypto calls, which could sleep, couldn't be called directly. Because of this the "confirm" and "random" work structs were introduced. These days the entire Bluetooth subsystem runs through workqueues which makes these structs unnecessary. This patch removes them and converts the calls to queue them to use direct function calls instead. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Fix setting initial local auth_req valueJohan Hedberg2014-05-201-4/+2
| | | | | | | | | There is no reason to have the initial local value conditional to whether the remote value has bonding set or not. We can either way start off with the value we received. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Make SMP context private to smp.cJohan Hedberg2014-05-205-29/+32
| | | | | | | | | | | | There are no users of the smp_chan struct outside of smp.c so move it away from smp.h. The addition of the l2cap.h include to hci_core.c, hci_conn.c and mgmt.c is something that should have been there already previously to avoid warnings of undeclared struct l2cap_conn, but the compiler warning was apparently shadowed away by the mention of l2cap_conn in the struct smp_chan definition. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add missing msecs to jiffies conversionAndrzej Kaczmarek2014-05-161-1/+2
| | | | | | | | conn_info_age value is calculated in ms, so need to be converted to jiffies. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add support for max_tx_power in Get Conn InfoAndrzej Kaczmarek2014-05-151-6/+17
| | | | | | | | | This patch adds support for max_tx_power in Get Connection Information request. Value is read only once for given connection and then always returned in response as parameter. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Store max TX power level for connectionAndrzej Kaczmarek2014-05-153-1/+13
| | | | | | | | This patch adds support to store local maximum TX power level for connection when reply for HCI_Read_Transmit_Power_Level is received. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Avoid polling TX power for LE linksAndrzej Kaczmarek2014-05-151-4/+10
| | | | | | | | TX power for LE links is immutable thus we do not need to query for it if already have value. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add support to get connection informationAndrzej Kaczmarek2014-05-153-0/+210
| | | | | | | | | | | | | | This patch adds support for Get Connection Information mgmt command which can be used to query for information about connection, i.e. RSSI and local TX power level. In general values cached in hci_conn are returned as long as they are considered valid, i.e. do not exceed age limit set in hdev. This limit is calculated as random value between min/max values to avoid client trying to guess when to poll for updated information. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add conn info lifetime parameters to debugfsAndrzej Kaczmarek2014-05-152-0/+69
| | | | | | | | | | | This patch adds conn_info_min_age and conn_info_max_age parameters to debugfs which determine lifetime of connection information. Actual lifetime will be random value between min and max age. Default values for min and max age are 1000ms and 3000ms respectively. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Store TX power level for connectionAndrzej Kaczmarek2014-05-094-0/+41
| | | | | | | | This patch adds support to store local TX power level for connection when reply for HCI_Read_Transmit_Power_Level is received. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Increment management interface revisionMarcel Holtmann2014-05-091-1/+1
| | | | | | | | This patch increments the management interface revision due to the changes with the Device Found management event and other fixes. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* Bluetooth: btusb: Add Broadcom patch RAM supportPetri Gynther2014-05-081-1/+154
| | | | | | | | | | | | | | | | | | | | | | | After hardware reset, some BCM Bluetooth adapters obtain their initial firmware from OTPROM chip. Once this initial firmware is running, the firmware can be further upgraded over HCI interface with .hcd files provided by Broadcom. This is also known as "patch RAM" support. This change implements that. If the .hcd file is not found in /lib/firmware, BCM Bluetooth adapter continues to operate with the initial firmware. Sample kernel log: hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=... Bluetooth: hci0: BCM: patch brcm/BCM20702A0-0a5c-22be.hcd not found If the .hcd file is found, btusb driver pushes it to the BCM Bluetooth adapter and it starts using the new firmware. Sample kernel log: hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=... Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=1000 lmp_ver=06 lmp_subver=220e Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=1389 lmp_ver=06 lmp_subver=220e Above, we can see that hci_rev goes from 1000 to 1389 as a result of the upgrade. Signed-off-by: Petri Gynther <pgynther@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Store RSSI for connectionAndrzej Kaczmarek2014-05-083-0/+34
| | | | | | | | This patch adds support to store RSSI for connection when reply for HCI_Read_RSSI is received. Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add support for SMP Invalid Parameters error codeJohan Hedberg2014-05-082-10/+11
| | | | | | | | | | The Invalid Parameters error code is used to indicate that the command length is invalid or that a parameter is outside of the specified range. This error code wasn't clearly specified in the Bluetooth 4.0 specification but since 4.1 this has been fixed. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Convert RFCOMM spinlocks into mutexesLibor Pechacek2014-05-053-14/+14
| | | | | | | | | Enabling CONFIG_DEBUG_ATOMIC_SLEEP has shown that some rfcomm functions acquiring spinlocks call sleeping locks further in the chain. Converting the offending spinlocks into mutexes makes sleeping safe. Signed-off-by: Libor Pechacek <lpechacek@suse.cz> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Remove hci_h4 unused definesPoulain, Loic2014-04-241-7/+0
| | | | | | | H4 states are not used anymore. Signed-off-by: Loic Poulain <loic.poulain@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
* Bluetooth: btmrvl: Fix btmrvl_send_module_cfg_cmd()Petri Gynther2014-04-242-2/+2
| | | | | | | | | Change subcmd parameter from int to u8 to match its use: btmrvl_send_sync_cmd(priv, BT_CMD_MODULE_CFG_REQ, &subcmd, 1); Signed-off-by: Petri Gynther <pgynther@google.com> Reviewed-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* Bluetooth: Return EOPNOTSUPP for HCISETRAW ioctl commandMarcel Holtmann2014-04-241-10/+1
| | | | | | | | | | | | | | The HCISETRAW ioctl command is not really useful. To utilize raw and direct access to the HCI controller, the HCI User Channel feature has been introduced. Return EOPNOTSUPP to indicate missing support for this command. For legacy reasons hcidump used to use HCISETRAW for permission check to return proper error codes to users. To keep backwards compability return EPERM in case the caller does not have CAP_NET_ADMIN capability. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* Bluetooth: Request MITM Protection when initiatorMikel Astiz2014-04-111-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | The GAP Specification gives the flexibility to decide whether MITM Protection is requested or not (Bluetooth Core Specification v4.0 Volume 3, part C, section 6.5.3) when replying to an HCI_EV_IO_CAPA_REQUEST event. The recommendation is *not* to set this flag "unless the security policy of an available local service requires MITM Protection" (regardless of the bonding type). However, the kernel doesn't necessarily have this information and therefore the safest choice is to always use MITM Protection, also for General Bonding. This patch changes the behavior for the General Bonding initiator role, always requesting MITM Protection even if no high security level is used. Depending on the remote capabilities, the protection might not be actually used, and we will accept this locally unless of course a high security level was originally required. Note that this was already done for Dedicated Bonding. No-Bonding is left unmodified because MITM Protection is normally not desired in these cases. Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de> Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* Bluetooth: Use MITM Protection when IO caps allow itTimo Mueller2014-04-111-7/+2
| | | | | | | | | | | | | | | | | | | | | | | | | When responding to a remotely-initiated pairing procedure, a MITM protected SSP associaton model can be used for pairing if both local and remote IO capabilities are set to something other than NoInputNoOutput, regardless of the bonding type (Dedicated or General). This was already done for Dedicated Bonding but this patch proposes to use the same policy for General Bonding as well. The GAP Specification gives the flexibility to decide whether MITM Protection is used ot not (Bluetooth Core Specification v4.0 Volume 3, part C, section 6.5.3). Note however that the recommendation is *not* to set this flag "unless the security policy of an available local service requires MITM Protection" (for both Dedicated and General Bonding). However, as we are already requiring MITM for Dedicated Bonding, we will follow this behaviour also for General Bonding. Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de> Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* Bluetooth: Refactor code for outgoing dedicated bondingMikel Astiz2014-04-112-10/+9
| | | | | | | | | | | | | Do not always set the MITM protection requirement by default in the field conn->auth_type, since this will be added later in hci_io_capa_request_evt(), as part of the requirements specified in HCI_OP_IO_CAPABILITY_REPLY. This avoids a hackish exception for the auto-reject case, but doesn't change the behavior of the code at all. Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* Bluetooth: Refactor hci_get_auth_req()Mikel Astiz2014-04-111-15/+22
| | | | | | | | | Refactor the code without changing its behavior by handling the no-bonding cases first followed by General Bonding. Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de> Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
* Bluetooth: Fix address in unmergeable device found eventsJohan Hedberg2014-03-291-3/+2
| | | | | | | | | | | | | When sending out a device found event caused by an advertising report in the situation where we couldn't store the report as a pending one, the code was incorrectly trying to use the address and address type from the pending data. Since the pending data is cleared in the previous line this causes a potentially incorrect address type and an address of BDADDR_ANY. This patch fixes the call to use the address information correctly from the received advertising report. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: btmrvl: implement read-to-clear for SD8897 interruptsBing Zhao2014-03-284-1/+73
| | | | | | | | | For SD8897, CMD52 write_to_clear may have missing interrupts under certain corner case condition. Use CMD53 read-to-clear to fix the problem. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Keep msec in DISCOV_LE_TIMEOUTLukasz Rymanowski2014-03-282-2/+2
| | | | | | | | | | To be consistent, lets use msec for this timeout as well. Note: This define value is a minimum scan time taken from BT Core spec 4.0, Vol 3, Part C, chapter 9.2.6 Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add new debugfs parameterLukasz Rymanowski2014-03-283-1/+6
| | | | | | | | | | With this patch it is possible to control discovery interleaved timeout value from debugfs. It is for fine tuning of this timeout. Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Keep msec in DISCOV_INTERLEAVED_TIMEOUTLukasz Rymanowski2014-03-282-5/+10
| | | | | | | | | | | Keep msec instead of jiffies in this define. This is needed by following patch where we want this timeout to be exposed in debugfs. Note: Value of this timeout comes from recommendation in BT Core Spec.4.0, Vol 3, Part C, chapter 13.2.1. Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: btmrvl: separate write-to-clear function from interrupt handlerBing Zhao2014-03-281-21/+32
| | | | | | | This patch improves readability and makes future changes easier. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Remove unnecessary NULL check in hci_inquiry_cache_updateJohan Hedberg2014-03-271-1/+1
| | | | | | | | | The ssp parameter is supposed to be a mandatory one and there are no callers that would pass NULL to this function. Removing this unnecessary NULL check also makes (false positive) static analyzer warnings go away. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Fix RSSI value in device found event from disabling scanJohan Hedberg2014-03-261-2/+3
| | | | | | | | When sending a pending device found event triggered by disabling LE scanning we should use the stored RSSI instead of sending a zero value. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Store also RSSI for pending advertising reportsJohan Hedberg2014-03-262-5/+8
| | | | | | | | | | | | | | | | Especially in crowded environments it can become frequent that we have to send out whatever pending event there is stored. Since user space has its own filtering of small RSSI changes sending a 0 value will essentially force user space to wake up the higher layers (e.g. over D-Bus) even though the RSSI didn't actually change more than the threshold value. This patch adds storing also of the RSSI for pending advertising reports so that we report an as accurate RSSI as possible when we have to send out the stored information to user space. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Don't send device found events for duplicate reportsJohan Hedberg2014-03-261-7/+12
| | | | | | | | | | Occasionally, during active scanning we will receive duplicate ADV_IND reports from the same device before receiving the SCAN_RSP from them. In order to not wake up user space unnecessarily it's better not to send these extra events as they do not contain any new information. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Fix line splitting of mgmt_device_found parametersJohan Hedberg2014-03-262-4/+4
| | | | | | | | The line was incorrectly split between the variable type and its name. This patch fixes the issue. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Remove redundant NULL checkJohan Hedberg2014-03-261-2/+1
| | | | | | | | | All callers of hci_inquiry_cache_update() pass a non-NULL ssp pointer to it and even the function itself assumes in another place that the pointer is non-NULL. Therefore, remove the redundant check. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Merge ADV_IND/ADV_SCAN_IND and SCAN_RSP togetherJohan Hedberg2014-03-262-2/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | To avoid too many events being sent to user space and to help parsing of all available remote device data it makes sense for us to wait for the scan response and send a single merged Device Found event to user space. This patch adds a few new variables to hci_dev to track the last received ADV_IND/ADV_SCAN_IND, i.e. those which will cause a SCAN_REQ to be send in the case of active scanning. When the SCAN_RSP is received the pending data is passed together with the SCAN_RSP to the mgmt_device_found function which takes care of merging them into a single Device Found event. We also need a bit of extra logic to handle situations where we don't receive a SCAN_RSP after caching some data. In such a scenario we simply have to send out the pending data as it is and then operate on the new report as if there was no pending data. We also need to send out any pending data when scanning stops as well as ensure that the storage is empty at the start of a new active scanning session. These both cases are covered by the update to the hci_cc_le_set_scan_enable function in this patch. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add directed advertising support through connect()Johan Hedberg2014-03-263-10/+87
| | | | | | | | | | | | | When we're in peripheral mode (HCI_ADVERTISING flag is set) the most natural mapping of connect() is to perform directed advertising to the peer device. This patch does the necessary changes to enable directed advertising and keeps the hci_conn state as BT_CONNECT in a similar way as is done for central or BR/EDR connection initiation. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add scan_rsp parameter to mgmt_device_found()Johan Hedberg2014-03-263-12/+19
| | | | | | | | | | | In preparation for being able to merge ADV_IND/ADV_SCAN_IND and SCAN_RSP together into a single device found event add a second parameter to the mgmt_device_found function. For now all callers pass NULL as this parameters since we don't yet have storing of the last received advertising report. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Don't send device found events during passive scanningJohan Hedberg2014-03-261-2/+6
| | | | | | | | | Passive LE scanning is only used by the kernel-internal connection establishment procedure. It makes therefore little sense to send device found events to user space. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Add error mapping for Directed Advertising TimeoutJohan Hedberg2014-03-261-0/+1
| | | | | | | | | When a timeout occurs using directed advertising a 0x3c error gets generated. Since the operation is analogous to conventional connection creation map this to the usual EHOSTDOWN error. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Fix LE responder/initiator address settingJohan Hedberg2014-03-261-12/+14
| | | | | | | | | | | | | | Once directed advertising is brought into the picture simply the lack of an hci_conn object when an le_conn_complete event occurs is no longer a reliable indication that the responder & initiator values need to be set based on our advertising address type. This patch moves the code for setting these values outside of the "if (!conn)" branch and ensures that they get set for any connection where we are in the slave role. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Move local identity address setting to a central placeJohan Hedberg2014-03-262-16/+4
| | | | | | | | | | | Any time hci_conn_add is used for an LE connection we need to ensure that the local identity address is correctly described in the src and src_type variables. This patch moves setting these values directly into hci_conn_add so that callers don't have to duplicate the effort themselves. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* Bluetooth: Use memdup_user in le_auto_conn_write()Andre Guedes2014-03-261-8/+3
| | | | | | | | | This patch does a small code simplification replacing the tipical kmalloc-copy_from_user sequence by memdup_user() helper. Cc: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
View Lorry Controller Status