| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.
So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up. This patch adds the device id to cdc_ether.c as a workaround.
Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c. See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.
I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.
Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The DCB netlink interface is required for building the userspace tools
available at e1000.sourceforge.net
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
1) add an include for <linux/types.h>
2) change dcbmsg.dcb_family from unsigned char to __u8 to be more
consistent with use of kernel types
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll. Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points. The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.
This patch adds the netpoll check to all entry points.
I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code). The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler
you're going to get a nice BUG_ON.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \ \ \
| | |/ / / / / |
|
| | |\ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The mesh and radiotap interfaces need to use the same private data as
the main wifi interface. If the main wifi interface uses netdev_priv(),
but the other interfaces ->ml_priv, there's no way to figure out where
the private data actually is in the WEXT handlers and netdevice
callbacks. So make everything use ->ml_priv.
Fixes botched netdev_priv() conversion introduced by "netdevice
libertas: Fix directly reference of netdev->priv", though admittedly
libertas' use of ->priv was somewhat "special".
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This patch fixes a wrong check on num_txbdfree. It could lead to
num_txbdfree become nagative. Result was that the gianfar stops
sending data.
Changes from first version :
- removed a space between parens (David Millers comment)
- full email address in signed off line
Signed-off-by: Rini van Zetten <rini@arvoo.nl>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
drr_change_class lacks a check for NULL of tca[TCA_OPTIONS], so oops
is possible.
Reported-by: Denys Fedoryschenko <denys@visp.net.lb>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Disable the SSB core on device shutdown.
This has two advantages:
1) A clean device shutdown is always desired here, because we disable
the device's global crystal in the next statement.
2) This fixes a bug where the device will come up with the enable-bit
set on the next initialization (without a reboot inbetween).
This causes breakage on the second initialization due to code that
checks this bit (ssb_device_is_enabled() checks).
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Unconditionally setup the IRQ routing on chip reset.
It's safe to call ssb_pcicore_dev_irqvecs_enable() unconditionally, because
it has internal checks for redundant calls.
This fixes problems where hardware will not come up properly
due to quirks in the enable-bit hardware.
Reported-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
hp-plus needs to call __alloc_eip_netdev() instead of
__alloc_ei_netdev() since it is linked with 8390p.o.
Fixes this build error:
ERROR: "__alloc_ei_netdev" [drivers/net/hp-plus.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ / / / / /
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We already have a valid net in that place, but this is not just a
cleanup - the tw pointer can be NULL there sometimes, thus causing
an oops in NET_NS=y case.
The same place in ipv4 code already works correctly using existing
net, rather than tw's one.
The bug exists since 2.6.27.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Add new USB ID codes. These come from two postings on forums and
mailing lists, and four are derived from the .inf that accompanies
the latest Realtek Windows driver for the RTL8187L.
Thanks to Viktor Ilijašić <viktor.ilijasic@gmail.com> and Xose Vazquez
Perez <xose.vazquez@gmail.com> for reporting these new ID's.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
[246916.338046]
[246916.338048] Pid: 29265, comm: insmod Not tainted (2.6.29-rc4-wl #64) 9461DUU
[246916.338051] EIP: 0060:[<c02ca274>] EFLAGS: 00010202 CPU: 0
[246916.338055] EIP is at rollback_registered+0x24/0x220
[246916.338057] EAX: 00000001 EBX: 00000000 ECX: 00000000 EDX: f122e8fc
[246916.338059] ESI: 00000000 EDI: 00000000 EBP: f6595d30 ESP: f6595d1c
[246916.338062] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[246916.338064] Process insmod (pid: 29265, ti=f6594000 task=f7343fe0 task.ti=f6594000)
[246916.338067] Stack:
[246916.338068] c04a2920 22222222 f6595d48 00000000 f122f080 f6595d48 c02ca489 f122e8fc
[246916.338076] f122e220 f122f080 f122e220 f6595d5c f8a03156 f122e220 f122f080 f122e220
[246916.338085] f6595d80 f87359af f122f080 00002000 f874e129 f122f150 f122f080 f6290000
[246916.338094] Call Trace:
[246916.338096] [<c02ca489>] ? unregister_netdevice+0x19/0x70
[246916.338100] [<f8a03156>] ? ieee80211_unregister_hw+0x36/0xd0 [mac80211]
[246916.338112] [<f87359af>] ? ath_detach+0xcf/0x250 [ath9k]
[246916.338127] [<f8735d9c>] ? ath_attach+0x26c/0x740 [ath9k]
[246916.338139] [<f873c33a>] ? ath_pci_probe+0x13a/0x310 [ath9k]
[246916.338151] [<c0233e28>] ? _raw_spin_unlock+0x68/0x80
[246916.338158] [<c023ab8e>] ? local_pci_probe+0xe/0x10
[246916.338162] [<c023b8e0>] ? pci_device_probe+0x60/0x80
[246916.338169] [<c029e042>] ? driver_probe_device+0x82/0x1b0
[246916.338174] [<c029e1f9>] ? __driver_attach+0x89/0x90
[246916.338180] [<c029d97b>] ? bus_for_each_dev+0x4b/0x70
[246916.338184] [<c023b820>] ? pci_device_remove+0x0/0x40
[246916.338190] [<c029ded9>] ? driver_attach+0x19/0x20
[246916.338193] [<c029e170>] ? __driver_attach+0x0/0x90
[246916.338197] [<c029d317>] ? bus_add_driver+0x1b7/0x230
[246916.338203] [<c023b820>] ? pci_device_remove+0x0/0x40
[246916.338206] [<c029e399>] ? driver_register+0x69/0x140
[246916.338212] [<f859d000>] ? ath9k_init+0x0/0x54 [ath9k]
[246916.338221] [<c023bb4e>] ? __pci_register_driver+0x4e/0x90
[246916.338225] [<f859d000>] ? ath9k_init+0x0/0x54 [ath9k]
[246916.338232] [<f859d06b>] ? ath_pci_init+0x17/0x19 [ath9k]
[246916.338238] [<f859d017>] ? ath9k_init+0x17/0x54 [ath9k]
[246916.338245] [<c017148e>] ? tracepoint_update_probe_range+0x7e/0xb0
[246916.338249] [<c010111a>] ? do_one_initcall+0x2a/0x170
[246916.338252] [<c0149f26>] ? up_read+0x16/0x30
[246916.338256] [<c014aa9d>] ? __blocking_notifier_call_chain+0x4d/0x60
[246916.338265] [<c0162b1a>] ? sys_init_module+0x8a/0x1c0
[246916.338269] [<c022f888>] ? trace_hardirqs_on_thunk+0xc/0x10
[246916.338272] [<c0103ebf>] ? sysenter_do_call+0x12/0x43
[246916.338276] Code: 8d bc 27 00 00 00 00 55 89 e5 56 89 c6 53 83 ec 0c a1 74 27 4a c0 85 c0 0f 85 4b 01 00 00 e8 04 7d 00 00 85 c0 0f 84 c9 01 00 00 <8b> 86 18 03 00 00 85 c0 0f 84 86 01 00 00 83 e8 01 0f 85 71 01
[246916.338328] EIP: [<c02ca274>] rollback_registered+0x24/0x220 SS:ESP 0068:f6595d1c
[246916.338335] ---[ end trace 76357c56a75ea34e ]---
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
With DEBUG_NOTIFIERS it results in
[11330.890966] WARNING: at /home/bor/src/linux-git/kernel/notifier.c:88
notifier_call_chain+0x91/0xa0()
[11330.890977] Hardware name: PORTEGE 4000
[11330.890983] Invalid notifier called! ...
Without DEBUG_NOTIFIERS it most likely crashes on NULL pointer.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This patch adds two new device ids to the asix driver.
One comes directly from the asix driver on their web site, the other was
reported by Armani Liao as needed for the MSI X320 to get the driver to
work properly for it.
Reported-by: Armani Liao <aliao@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \ \ \ \
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
Fix regression introduded by commit 079aa88 (netfilter: xt_recent: IPv6 support):
From http://bugzilla.kernel.org/show_bug.cgi?id=12753:
Problem Description:
An uninitialized buffer causes IPv4 addresses added manually (via the +IP
command to the proc interface) to never match any packets. Similarly, the -IP
command fails to remove IPv4 addresses.
Details:
In the function recent_entry_lookup, the xt_recent module does comparisons of
the entire nf_inet_addr union value, both for IPv4 and IPv6 addresses. For
addresses initialized from actual packets the remaining 12 bytes not occupied
by the IPv4 are zeroed so this works correctly. However when setting the
nf_inet_addr addr variable in the recent_mt_proc_write function, only the IPv4
bytes are initialized and the remaining 12 bytes contain garbage.
Hence addresses added in this way never match any packets, unless these
uninitialized 12 bytes happened to be zero by coincidence. Similarly, addresses
cannot consistently be removed using the proc interface due to mismatch of the
garbage bytes (although it will sometimes work to remove an address that was
added manually).
Reading the /proc/net/xt_recent/ entries hides this problem because this only
uses the first 4 bytes when displaying IPv4 addresses.
Steps to reproduce:
$ iptables -I INPUT -m recent --rcheck -j LOG
$ echo +169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
[At this point no packets from 169.254.156.239 are being logged.]
$ iptables -I INPUT -s 169.254.156.239 -m recent --set
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126184 oldest_pkt: 4 125434, 125684, 125934, 126184
[At this point, adding the address via an iptables rule, packets are being
logged correctly.]
$ echo -169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126992 oldest_pkt: 10 125434, 125684, 125934, 126184, 126434, 126684, 126934, 126991, 126991, 126992
$ echo -169.254.156.239 > /proc/net/xt_recent/DEFAULT
$ cat /proc/net/xt_recent/DEFAULT
src=169.254.156.239 ttl: 0 last_seen: 119910 oldest_pkt: 1 119910
src=169.254.156.239 ttl: 255 last_seen: 126992 oldest_pkt: 10 125434, 125684, 125934, 126184, 126434, 126684, 126934, 126991, 126991, 126992
[Removing the address via /proc interface failed evidently.]
Possible solutions:
- initialize the addr variable in recent_mt_proc_write
- compare only 4 bytes for IPv4 addresses in recent_entry_lookup
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
When extensions were moved to the NFPROTO_UNSPEC wildcard in
ab4f21e6fb1c09b13c4c3cb8357babe8223471bd, they disappeared from the
procfs files.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
The untracked conntrack actually does usually have events marked for
delivery as its not special-cased in that part of the code. Skip the
actual delivery since it impacts performance noticeably.
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
NFLOG timeout was computed in timer by doing:
flushtimeout*HZ/100
Default value of flushtimeout was HZ (for 1 second delay). This was
wrong for non 100HZ computer. This patch modify the default delay by
using 100 instead of HZ.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
In NFLOG the per-rule qthreshold should overrides per-instance only
it is set. With current code, the per-rule qthreshold is 1 if not set
and it overrides the per-instance qthreshold.
This patch modifies the default xt_NFLOG threshold from 1 to
0. Thus a value of 0 means there is no per-rule setting and the instance
parameter has to apply.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
| | | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
This patch fixes a trivial typo that was adding a new line at end of
the nf_log_packet() prefix. It also make the logging conditionnal by
adding a LOG_INVALID test.
Signed-off-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
| | | |\ \ \ \ \ \ \ |
|
| | |\ \ \ \ \ \ \ \ \ |
|
| | | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | | |
PCI bar 0 is used for memory mapped register access.
If ioremap fails (returns NULL), register access results
in crash.
Use pci_ioremap_bar() instead of ioremap(), the latter
fails on on 32 bit powerpc where pci resource address is
> 32 bits.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | | |
The PCI function to physical port mapping is valid only for
old firmware. New firmware (4.0.0+) abstracts this.
So driver should never try to access phy using invalid
mapping. The behavior is unpredictable when PCI functions
4-7 are enabled on the same NIC.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \ \ \ \ \ \ \ \ \
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
selinux: Fix a panic in selinux_netlbl_inode_permission()
|
| | | |_|_|_|_|/ / / / /
| |/| | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | | |
Rick McNeal from LSI identified a panic in selinux_netlbl_inode_permission()
caused by a certain sequence of SUNRPC operations. The problem appears to be
due to the lack of NULL pointer checking in the function; this patch adds the
pointer checks so the function will exit safely in the cases where the socket
is not completely initialized.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
| | | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | | |
Since I will loose the old address soon, please change it.
Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \ \ \ \ \ \ \ \ \ \
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Some Logitech mice react to the magic knock like Elantech touchpad would.
This leads to those mice being misdetected as Elantech touchpads. Add a
version query to elantech_detect() to distinguish the two.
[dtor@mail.ru:
- lower severity of some messages - when we are not sure yet if
device is Elantech or not not responding to knock is not an error.
]
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
When resuming from suspend newer Synaptics touchpads do not recover
correctly. Analysis of the resume sequence as applied in Linux was
compared to that of other operating systems. This indicated that the
other OSs were resetting the mouse before attempting to detect it (for
all Synaptics touchpads, old and new). Applying this same modification
fixes these newer Synaptics touchpads and brings the driver into line
with common OS reset behaviour.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Commit ec42d4481e36cbdb5b2801f957e678211a9e5ae2 broke usbtouchscreen for
some eGalax/EETI devices that claim to be HID, but are not.
Devices confirmed to be real HID have the class set to HID and the protocol
set to 'mouse'. Some have HID class but protocol set to 'none'. Those are
not HID and should be driven by usbtouchscreen.
Fix the device ignoring macro by adding match for the protocol too.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
With a postfix decrement timeleft reaches -1 rather than 0,
but after the loop it is tested to have become 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
With a postfix decrement i reaches -1 rather than 0,
but after the loop it is tested whether it has become 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
A pointer to spitzkbd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
A pointer to omap_kp_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
A pointer to corgits_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
A pointer to corgikbd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
[dtor@mail.ru: fixed some more section markups]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Cameras should generate KEY_CAMERA, not BTN_0. Also call input_sync()
on the device once the button has been pressed.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
All Fujitsu-Siemens Lifebook systems are x86-based, so we might
as well make MOUSE_PS2_LIFEBOOK depend on X86. This will avoid
surprising things like:
arch/arm/configs/s3c2410_defconfig:CONFIG_MOUSE_PS2_LIFEBOOK=y
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
