summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: imx: Use generic uart-has-rtscts DT propertyGeert Uytterhoeven2016-06-111-3/+3
| | | | | | | | | | | As of commit 1006ed7e1b258dac ("serial: imx: Use generic uart-has-rtscts DT property"), the Freescale IMX UART driver recognizes the generic "uart-has-rtscts" DT property, deprecating the vendor-specific "fsl,uart-has-rtscts" DT property. Hence replace the latter by the former in all DTS files. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* ARM: dts: Add stdout-path property to i.MX boardsSascha Hauer2014-05-161-0/+4
| | | | | | | | | | This adds the stdout-path property to various i.MX boards. Values of the property have been taken from barebox, so they should be correct. Also, the older linux,stdout-path property is converted to stdout-path. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
* ARM: dts: imx27-phytec-phycard-s-som: Rename file to .dtsiAlexander Shiyan2014-02-131-1/+1
| | | | | | | | PCA-100 module cannot be used standalone. This patch renames module file to .dtsi and excludes it from compilation. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: imx27-phytec-phycard-s-rdk: Add pinctrl definitions for SDHC2Alexander Shiyan2014-02-101-0/+14
| | | | | | | | This patch adds pinctrl definitions for SDHC2 for Phytec PCA100 RDK board. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: i.MX27 boards: Switch to use standard GPIO and IRQ flags definitionsAlexander Shiyan2014-02-091-1/+1
| | | | | Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: imx27 phyCARD-S pinctrlMarkus Pargmann2014-02-091-0/+54
| | | | | | | Add pinctrl nodes and properties for phyCARD-S device nodes. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: imx: use generic node name for fixed regulatorShawn Guo2014-02-091-1/+4
| | | | | | | | The device tree specification recommends that generic name should be used for nodes. So instead of naming those fixed regulator nodes arbitrarily, let's use the generic name 'regulator@num' for those nodes. Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: imx27 phyCARD-S, i2c ADC device nodeMarkus Pargmann2013-08-221-0/+18
| | | | | Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: imx27 phyCARD-S, move i2c1 and owire to rdkMarkus Pargmann2013-08-221-0/+13
| | | | | | | | Both buses are not used on the phyCARD-S module. This patch moves them to the rdk file. Remove ioexpander. Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* ARM: dts: Add device tree support for phycard pca100Markus Pargmann2013-08-221-0/+62
Board files for Phytec phyCARD-S "System on Module" and "Rapid Development Kit". Based on patches from: Steffen Trumtrar <s.trumtrar@pengutronix.de>: - Original patch - ARM: dts: Set partition offsets for phycard - ARM: dts: Use CSPI1 instead of CSPI2 on phycard pca100 - ARM: imx27-phytec-phycard-S.dts: resize nand partitions Jan Luebbe <jlu@pengutronix.de>: - ARM: dts: Enable bad block table in NAND Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de> Cc: Jan Luebbe <jlu@pengutronix.de> Signed-off-by: Markus Pargmann <mpa@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
View Lorry Controller Status