summaryrefslogtreecommitdiff
path: root/arch/powerpc/kernel/eeh_sysfs.c
Commit message (Collapse)AuthorAgeFilesLines
* powerpc/eeh: Remove unnecessary config_addr from eeh_devAlexey Kardashevskiy2017-08-311-3/+0
| | | | | | | | | | | | | | | The eeh_dev struct hold a config space address of an associated node and the very same address is also stored in the pci_dn struct which is always present during the eeh_dev lifetime. This uses bus:devfn directly from pci_dn instead of cached and packed config_addr. Since config_addr is made from device's bus:dev.fn, there is no point in keeping it in the debugfs either so remove that too. Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* powerpc/eeh: Fix PE state formatGavin Shan2014-11-271-1/+1
| | | | | | | | | | Obviously I had wrong format given to the PE state output from /sys/bus/pci/devices/xxxx/eeh_pe_state with some typoes, which was introduced by commit 2013add4ce73. The patch fixes it up. Fixes: 2013add4ce73 ("powerpc/eeh: Show hex prefix for PE state sysfs") Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* powerpc/eeh: Show hex prefix for PE state sysfsGavin Shan2014-10-011-1/+1
| | | | | | | | | | As Michael suggested, the hex prefix for the output of EEH PE state sysfs entry (/sys/bus/pci/devices/xxx/eeh_pe_state) is always informative to users. Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* powerpc/eeh: Use eeh_unfreeze_pe()Gavin Shan2014-09-301-20/+1
| | | | | | | | The patch uses eeh_unfreeze_pe() to replace the logic clearing frozen IO and DMA, in order to simplify the code. Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* powerpc/eeh: Add eeh_pe_state sysfs entryGavin Shan2014-09-301-1/+59
| | | | | | | | | | | | | The patch adds sysfs entry "eeh_pe_state". Reading on it returns the PE's state while writing to it clears the frozen state. It's used to check or clear the PE frozen state from userland for debugging purpose. The patch also replaces printk(KERN_WARNING ...) with pr_warn() in eeh_sysfs.c Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* powerpc/eeh: Skip eeh sysfs when eeh is disabledWei Yang2014-06-051-0/+3
| | | | | | | | | | | | | | | | | | | When eeh is not enabled, and hotplug two pci devices on the same bus, eeh related sysfs would be added twice for the first added pci device. Since the eeh_dev is not created when eeh is not enabled. This patch adds the check, if eeh is not enabled, eeh sysfs will not be created. After applying this patch, following warnings are reduced: sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_mode' sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_config_addr' sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:00.0/eeh_pe_config_addr' Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com> Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* powerpc/eeh: Introdce flag to protect sysfsGavin Shan2013-07-241-1/+15
| | | | | | | | | The patch introduces flag EEH_DEV_SYSFS to keep track that the sysfs entries for the corresponding EEH device (then PCI device) has been added or removed, in order to avoid race condition. Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* powerpc/eeh: Use partial hotplug for EEH unaware driversGavin Shan2013-07-241-0/+7
| | | | | | | | | | | | | | | | | | | | | | When EEH error happens to one specific PE, some devices with drivers supporting EEH won't except hotplug on the device. However, there might have other deivces without driver, or with driver without EEH support. For the case, we need do partial hotplug in order to make sure that the PE becomes absolutely quite during reset. Otherise, the PE reset might fail and leads to failure of error recovery. The current code doesn't handle that 'mixed' case properly, it either uses the error callbacks to the drivers, or tries hotplug, but doesn't handle a PE (EEH domain) composed of a combination of the two. The patch intends to support so-called "partial" hotplug for EEH: Before we do reset, we stop and remove those PCI devices without EEH sensitive driver. The corresponding EEH devices are not detached from its PE, but with special flag. After the reset is done, those EEH devices with the special flag will be scanned one by one. Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* powerpc/eeh: Move common part to kernel directoryGavin Shan2013-06-201-0/+74
The patch moves the common part of EEH core into arch/powerpc/kernel directory so that we needn't PPC_PSERIES while compiling POWERNV platform: * Move the EEH common part into arch/powerpc/kernel * Move the functions for PCI hotplug from pSeries platform to arch/powerpc/kernel/pci-hotplug.c * Move CONFIG_EEH from arch/powerpc/platforms/pseries/Kconfig to arch/powerpc/platforms/Kconfig * Adjust makefile accordingly Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>