summaryrefslogtreecommitdiff
path: root/drivers/mmc/host/dw_mmc.c
Commit message (Collapse)AuthorAgeFilesLines
* mmc: dw_mmc: Drop use of ->init_card() callbackUlf Hansson2021-10-211-22/+17
| | | | | | | | | | | | | | | | | | For dw_mmc, the ->init_card() callback is being used to turn on/off automatic internal clock gating for powersave, which is needed to properly support SDIO irqs on DAT1. However, using the ->init_card() comes with a drawback in this case, as it means that the powersave feature becomes disabled, no matter whether the SDIO irqs becomes turned on or not. To improve the behaviour, let's change into using the ->enable_sdio_irq() callback instead. This works fine, because dw_mmc uses sdio_signal_irq() to signal the irqs, thus the ->enable_sdio_irq() is never executed from within atomic context. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20211020102907.70195-1-ulf.hansson@linaro.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Dont wait for DRTO on Write RSP errorChristian Löhle2021-10-121-1/+2
| | | | | | | | | | | | | | | | | | | | | | Only wait for DRTO on reads, otherwise the driver hangs. The driver prevents sending CMD12 on response errors like CRCs. According to the comment this is because some cards have problems with this during the UHS tuning sequence. Unfortunately this workaround currently also applies for any command with data. On reads this will set the drto timer, which then triggers after a while. On writes this will not set any timer and the tasklet will not be scheduled again. I cannot test for the UHS workarounds need, but even if so, it should at most apply to reads. I have observed many hangs when CMD25 response contained a CRC error. This patch fixes this without touching the actual UHS tuning workaround. Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Only inject fault before done/errorVincent Whitchurch2021-09-061-3/+12
| | | | | | | | | | | | | | | | | | The fault injection function can set EVENT_DATA_ERROR but skip the setting of ->data_status to an error status if it hits just after a data over interrupt. This confuses the tasklet which can later end up triggering the WARN_ON(host->cmd || ..) in dw_mci_request_end() since dw_mci_data_complete() would return success. Prevent the fault injection function from doing this since this is not a real case, and ensure that the fault injection doesn't race with a real error either. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Fixes: 2b8ac062f337 ("mmc: dw_mmc: Add data CRC error injection") Link: https://lore.kernel.org/r/20210825114213.7429-1-vincent.whitchurch@axis.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Fix issue with uninitialized dma_slave_configTony Lindgren2021-08-241-0/+1
| | | | | | | | | | | | | | | | | | | | | Depending on the DMA driver being used, the struct dma_slave_config may need to be initialized to zero for the unused data. For example, we have three DMA drivers using src_port_window_size and dst_port_window_size. If these are left uninitialized, it can cause DMA failures. For dw_mmc, this is probably not currently an issue but is still good to fix though. Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support") Cc: Shawn Lin <shawn.lin@rock-chips.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Cc: Vinod Koul <vkoul@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Add data CRC error injectionVincent Whitchurch2021-08-241-0/+73
| | | | | | | | | | | | | | | | | This driver has had problems when handling data errors. Add fault injection support so that the abort handling can be easily triggered and regression-tested. A hrtimer is used to indicate a data CRC error at various points during the data transfer. Note that for the recent problem with hangs in the case of some data CRC errors, a udelay(10) inserted at the start of send_stop_abort() greatly helped in triggering the error, but I've not included this as part of the fault injection support since it seemed too specific. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Fix hang on data CRC errorVincent Whitchurch2021-08-041-3/+3
| | | | | | | | | | | | | | | | | | | | | When a Data CRC interrupt is received, the driver disables the DMA, then sends the stop/abort command and then waits for Data Transfer Over. However, sometimes, when a data CRC error is received in the middle of a multi-block write transfer, the Data Transfer Over interrupt is never received, and the driver hangs and never completes the request. The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed "before assertion of SWR". Do these operations in the recommended order. With this change the Data Transfer Over is always received correctly in my tests. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: simplify optional reset handlingPhilipp Zabel2021-03-301-9/+5
| | | | | | | | | | | | | As of commit bb475230b8e5 ("reset: make optional functions really optional"), the reset framework API calls use NULL pointers to describe optional, non-present reset controls. This allows to return errors from devm_reset_control_get_optional and to call reset_control_(de)assert unconditionally. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Link: https://lore.kernel.org/r/20210305090724.18832-1-p.zabel@pengutronix.de Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Drop redundant call to ->card_event callbackUlf Hansson2021-03-301-2/+0
| | | | | | | | | The ->card_event callback isn't being used by any of the dw_mmc variants. It's likely a leftover from an earlier change, hence let's just drop the redundant call to it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: dw_mmc: Use new tasklet APIEmil Renner Berthing2021-02-081-3/+3
| | | | | | | | | This converts the driver to use the new tasklet API introduced in commit 12cc923f1ccc ("tasklet: Introduce new initialization API") Signed-off-by: Emil Renner Berthing <kernel@esmil.dk> Link: https://lore.kernel.org/r/20210204151847.91353-4-kernel@esmil.dk Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: replace spin_lock_irqsave by spin_lock in hard IRQTian Tao2020-11-161-9/+8
| | | | | | | | | The code has been in a irq-disabled context since it is hard IRQ. There is no necessity to do it again. Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Link: https://lore.kernel.org/r/1604627813-59785-1-git-send-email-tiantao6@hisilicon.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Simplify with dev_err_probe()Krzysztof Kozlowski2020-09-071-6/+3
| | | | | | | | | | Common pattern of handling deferred probe can be simplified with dev_err_probe(). Less code, the error value gets printed and real error from dw_mci_parse_dt() is passed further instead of fixed -EINVAL. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20200902193658.20539-10-krzk@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* treewide: Use fallthrough pseudo-keywordGustavo A. R. Silva2020-08-231-3/+3
| | | | | | | | | | Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
* mmc: host: Drop redundant MMC_CAP_ERASEUlf Hansson2020-05-281-6/+0
| | | | | | | | | | | The MMC_CAP_ERASE bit is no longer used by the mmc core as erase, discard and trim operations are now always supported. Therefore, drop the bit and move all mmc hosts away from using it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> Link: https://lore.kernel.org/r/20200508112902.23575-1-ulf.hansson@linaro.org Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
* mmc: host: Prepare host drivers for mmc_regulator_set_vqmmc() returning > 0Marek Vasut2020-05-281-2/+1
| | | | | | | | | | | | Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would happen if the signal voltage switch did NOT happen, because the voltage was already set correctly. Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de [Ulf: Re-worked/simplified the code a bit] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Use dma_request_chan() instead dma_request_slave_channel()Peter Ujfalusi2019-12-191-3/+5
| | | | | | | | | | | | dma_request_slave_channel() is a wrapper on top of dma_request_chan() eating up the error code. By using dma_request_chan() directly the driver can support deferred probing against DMA. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20191217112656.30860-1-peter.ujfalusi@ti.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Merge tag 'driver-core-5.5-rc1' of ↵Linus Torvalds2019-11-271-5/+5
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here is the "big" set of driver core patches for 5.5-rc1 There's a few minor cleanups and fixes in here, but the majority of the patches in here fall into two buckets: - debugfs api cleanups and fixes - driver core device link support for boot dependancy issues The debugfs api cleanups are working to slowly refactor the debugfs apis so that it is even harder to use incorrectly. That work has been happening for the past few kernel releases and will continue over time, it's a long-term project/goal The driver core device link support missed 5.4 by just a bit, so it's been sitting and baking for many months now. It's from Saravana Kannan to help resolve the problems that DT-based systems have at boot time with dependancy graphs and kernel modules. Turns out that no one has actually tried to build a generic arm64 kernel with loads of modules and have it "just work" for a variety of platforms (like a distro kernel). The big problem turned out to be a lack of dependency information between different areas of DT entries, and the work here resolves that problem and now allows devices to boot properly, and quicker than a monolith kernel. All of these patches have been in linux-next for a long time with no reported issues" * tag 'driver-core-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (68 commits) tracing: Remove unnecessary DEBUG_FS dependency of: property: Add device link support for interrupt-parent, dmas and -gpio(s) debugfs: Fix !DEBUG_FS debugfs_create_automount of: property: Add device link support for "iommu-map" of: property: Fix the semantics of of_is_ancestor_of() i2c: of: Populate fwnode in of_i2c_get_board_info() drivers: base: Fix Kconfig indentation firmware_loader: Fix labels with comma for builtin firmware driver core: Allow device link operations inside sync_state() driver core: platform: Declare ret variable only once cpu-topology: declare parse_acpi_topology in <linux/arch_topology.h> crypto: hisilicon: no need to check return value of debugfs_create functions driver core: platform: use the correct callback type for bus_find_device firmware_class: make firmware caching configurable driver core: Clarify documentation for fwnode_operations.add_links() mailbox: tegra: Fix superfluous IRQ error message net: caif: Fix debugfs on 64-bit platforms mac80211: Use debugfs_create_xul() helper media: c8sectpfe: no need to check return value of debugfs_create functions of: property: Add device link support for iommus, mboxes and io-channels ...
| * mmc: dw_mmc: Remove superfluous cast in debugfs_create_u32() callGeert Uytterhoeven2019-11-031-1/+1
| | | | | | | | | | | | | | | | | | | | "dw_mci.state" is an enum, which is compatible with u32, so there is no need to cast its address, preventing further compiler checks. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20191025094130.26033-8-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * mmc: dw_mmc: Fix debugfs on 64-bit platformsGeert Uytterhoeven2019-11-031-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | "dw_mci.pending_events" and "dw_mci.completed_events" are "unsigned long", i.e. 32-bit or 64-bit, depending on the platform. Hence casting their addresses to "u32 *", and calling debugfs_create_x32() breaks operation on 64-bit platforms. Fix this by using the new debugfs_create_xul() helper instead. Fixes: f95f3850f7a9e1d4 ("mmc: dw_mmc: Add Synopsys DesignWare mmc host driver.") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20191025094130.26033-7-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | mmc: dw_mmc: fix indentation issueColin Ian King2019-11-131-2/+2
|/ | | | | | | | There are a couple of statements that are indented by an extra space, clean this up by remove the extraneous spaces. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Re-store SDIO IRQs mask at system resumeUlf Hansson2019-09-111-0/+4
| | | | | | | | | | | | | | | | | | | In cases when SDIO IRQs have been enabled, runtime suspend is prevented by the driver. However, this still means dw_mci_runtime_suspend|resume() gets called during system suspend/resume, via pm_runtime_force_suspend|resume(). This means during system suspend/resume, the register context of the dw_mmc device most likely loses its register context, even in cases when SDIO IRQs have been enabled. To re-enable the SDIO IRQs during system resume, the dw_mmc driver currently relies on the mmc core to re-enable the SDIO IRQs when it resumes the SDIO card, but this isn't the recommended solution. Instead, it's better to deal with this locally in the dw_mmc driver, so let's do that. Tested-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Fix occasional hang after tuning on eMMCDouglas Anderson2019-07-221-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after response errors.") we fixed a tuning-induced hang that I saw when stress testing tuning on certain SD cards. I won't re-hash that whole commit, but the summary is that as a normal part of tuning you need to deal with transfer errors and there were cases where these transfer errors was putting my system into a bad state causing all future transfers to fail. That commit fixed handling of the transfer errors for me. In downstream Chrome OS my fix landed and had the same behavior for all SD/MMC commands. However, it looks like when the commit landed upstream we limited it to only SD tuning commands. Presumably this was to try to get around problems that Alim Akhtar reported on exynos [1]. Unfortunately while stress testing reboots (and suspend/resume) on some rk3288-based Chromebooks I found the same problem on the eMMC on some of my Chromebooks (the ones with Hynix eMMC). Since the eMMC tuning command is different (MMC_SEND_TUNING_BLOCK_HS200 vs. MMC_SEND_TUNING_BLOCK) we were basically getting back into the same situation. I'm hoping that whatever problems exynos was having in the past are somehow magically fixed now and we can make the behavior the same for all commands. [1] https://lkml.kernel.org/r/CAGOxZ53WfNbaMe0_AM0qBqU47kAfgmPBVZC8K8Y-_J3mDMqW4A@mail.gmail.com Fixes: 46d179525a1f ("mmc: dw_mmc: Wait for data transfer after response errors.") Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Alim Akhtar <alim.akhtar@gmail.com> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: host: dw_mmc: no need to check return value of debugfs_create functionsGreg Kroah-Hartman2019-06-171-29/+7
| | | | | | | | | | When calling debugfs functions, there is no need to ever check the return value. The function can work or not, but the code logic should never do something different based on this Cc: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152Thomas Gleixner2019-05-301-5/+1
| | | | | | | | | | | | | | | | | | | | | Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license as published by the free software foundation either version 2 of the license or at your option any later version extracted by the scancode license scanner the SPDX license identifier GPL-2.0-or-later has been chosen to replace the boilerplate/reference in 3029 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mmc: dw_mmc: fix card threshold control configurationx002701702018-07-031-3/+4
| | | | | | | | | | | | | | Card write threshold control is supposed to be set since controller version 2.80a for data write in HS400 mode and data read in HS200/HS400/SDR104 mode. However the current code returns without configuring it in the case of data writing in HS400 mode. Meanwhile the patch fixes that the current code goes to 'disable' when doing data reading in HS400 mode. Fixes: 7e4bf1bc9543 ("mmc: dw_mmc: add the card write threshold for HS400 mode") Signed-off-by: Qing Xia <xiaqing17@hisilicon.com> Cc: stable@vger.kernel.org # v4.8+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: update actual clock for mmc debugfsShawn Lin2018-05-021-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | Respect the actual clock for mmc debugfs to help better debug the hardware. mmc_host mmc0: Bus speed (slot 0) = 135475200Hz (slot req 150000000Hz, actual 135475200HZ div = 0) cat /sys/kernel/debug/mmc0/ios clock: 150000000 Hz actual clock: 135475200 Hz vdd: 21 (3.3 ~ 3.4 V) bus mode: 2 (push-pull) chip select: 0 (don't care) power mode: 2 (on) bus width: 3 (8 bits) timing spec: 9 (mmc HS200) signal voltage: 0 (1.80 V) driver type: 0 (driver type B) Cc: Xiao Yao <xiaoyao@rock-chips.com> Cc: Ziyuan <xzy.xu@rock-chips.com> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Merge branch 'fixes' into nextUlf Hansson2018-03-161-2/+4
|\
| * mmc: dw_mmc: fix falling from idmac to PIO mode when dw_mci_reset occursEvgeniy Didin2018-03-161-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It was found that in IDMAC mode after soft-reset driver switches to PIO mode. That's what happens in case of DTO timeout overflow calculation failure: 1. soft-reset is called 2. driver restarts dma 3. descriptors states are checked, one of descriptor is owned by the IDMAC. 4. driver can't use DMA and then switches to PIO mode. Failure was already fixed in: https://www.spinics.net/lists/linux-mmc/msg48125.html. Behaviour while soft-reset is not something we except or even want to happen. So we switch from dw_mci_idmac_reset to dw_mci_idmac_init, so descriptors are cleaned before starting dma. And while at it explicitly zero des0 which otherwise might contain garbage as being allocated by dmam_alloc_coherent(). Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Cc: Shawn Lin <shawn.lin@rock-chips.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Cc: linux-snps-arc@lists.infradead.org Cc: <stable@vger.kernel.org> # 4.4+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: dw_mmc: remove the deprecated "num-slots"Jaehoon Chung2018-03-151-4/+0
| | | | | | | | | | | | | | | | | | 'num-slots' property had already deprecated. Remove the 'nom-slots' property that is kept to maintain the compatibility. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: dw_mmc: remove the deprecated "clock-freq-min-max" propertyJaehoon Chung2018-03-151-11/+4
| | | | | | | | | | | | | | | | | | | | 'clock-freq-min-max' property had already deprecated. Remove the 'clock-freq-min-max' property that is kept to maintain the compatibility. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | Merge branch 'fixes' into nextUlf Hansson2018-03-051-3/+6
|\ \ | |/
| * mmc: dw_mmc: Fix the DTO/CTO timeout overflow calculation for 32-bit systemsEvgeniy Didin2018-03-051-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit 9d9491a7da2a ("mmc: dw_mmc: Fix the DTO timeout calculation") and commit 4c2357f57dd5 ("mmc: dw_mmc: Fix the CTO timeout calculation") made changes, which cause multiply overflow for 32-bit systems. The broken timeout calculations leads to unexpected ETIMEDOUT errors and causes stacktrace splat (such as below) during normal data exchange with SD-card. | Running : 4M-check-reassembly-tcp-cmykw2-rotatew2.out -v0 -w1 | - Info: Finished target initialization. | mmcblk0: error -110 transferring data, sector 320544, nr 2048, cmd | response 0x900, card status 0x0 DIV_ROUND_UP_ULL helps to escape usage of __udivdi3() from libgcc and so code gets compiled on all 32-bit platforms as opposed to usage of DIV_ROUND_UP when we may only compile stuff on a very few arches. Lets cast this multiply to u64 type to prevent the overflow. Fixes: 9d9491a7da2a ("mmc: dw_mmc: Fix the DTO timeout calculation") Fixes: 4c2357f57dd5 ("mmc: dw_mmc: Fix the CTO timeout calculation") Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> # ARC STAR 9001306872 HSDK, sdio: board crashes when copying big files Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: <stable@vger.kernel.org> # 4.14 Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: dw_mmc: Remove prev_state and state assignment for STATE_SENDING_CMDShawn Lin2018-03-051-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Clang reports a compile warning: drivers/mmc/host/dw_mmc.c:2124:5: warning: Value stored to 'prev_state' is never read By checking the code, prev_state and state assignment for STATE_SENDING_CMD is indeed never used after jumping to unlock tag. So remove it. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: dw_mmc: Convert to use DEFINE_SHOW_ATTRIBUTEShawn Lin2018-03-051-26/+2
|/ | | | | | | | Use the newly added macro to simply to the code. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Avoid accessing registers in runtime suspended stateShawn Lin2018-02-271-0/+4
| | | | | | | | | | | | | cat /sys/kernel/debug/mmc0/regs will hang up the system since it's in runtime suspended state, so the genpd and biu_clk is off. This patch fixes this problem by calling pm_runtime_get_sync to wake it up before reading the registers. Fixes: e9ed8835e990 ("mmc: dw_mmc: add runtime PM callback") Cc: <stable@vger.kernel.org> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Fix out-of-bounds access for slot's capsShawn Lin2018-02-271-1/+8
| | | | | | | | | | | Add num_caps field for dw_mci_drv_data to validate the controller id from DT alias and non-DT ways. Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks") Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Factor out dw_mci_init_slot_capsShawn Lin2018-02-271-30/+43
| | | | | | | | | | | Factor out dw_mci_init_slot_caps to consolidate parsing all differents types of capabilities from host contrllers. No functional change intended. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks") Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Convert timers to use timer_setup()Kees Cook2017-11-021-14/+9
| | | | | | | | | | | | In preparation for unconditionally passing the struct timer_list pointer to all timer callbacks, switch to using the new timer_setup() and from_timer() to pass the timer pointer explicitly. Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: linux-mmc@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: Cleanup the DTO timer like the CTO oneDouglas Anderson2017-11-021-3/+52
| | | | | | | | | | | | | | | | | | | | | | | | | The recent CTO timer introduced in commit 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme") was causing observable problems due to race conditions. Previous patches have fixed those race conditions. It can be observed that these same race conditions ought to be theoretically possible with the DTO timer too though they are massively less likely to happen because the data timeout is always set to 0xffffff right now. That means even at a 200 MHz card clock we were arming the DTO timer for 94 ms: >>> (0xffffff * 1000. / 200000000) + 10 93.886075 We always also were setting the DTO timer _after_ starting the transfer, unlike how the old code was seting the CTO timer. In any case, even though the DTO timer is much less likely to have races, it still makes sense to add code to handle it _just in case_. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Merge branch 'fixes' into nextUlf Hansson2017-11-021-13/+94
|\
| * mmc: dw_mmc: Fix the DTO timeout calculationDouglas Anderson2017-11-011-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Just like the CTO timeout calculation introduced recently, the DTO timeout calculation was incorrect. It used "bus_hz" but, as far as I can tell, it's supposed to use the card clock. Let's account for the div value, which is documented as 2x the value stored in the register, or 1 if the register is 0. NOTE: This was likely not terribly important until commit 16a34574c6ca ("mmc: dw_mmc: remove the quirks flags") landed because "DIV" is documented on Rockchip SoCs (the ones that used to define the quirk) to always be 0 or 1. ...and, in fact, it's documented to only be 1 with EMMC in 8-bit DDR52 mode. Thus before the quirk was applied to everyone it was mostly OK to ignore the DIV value. I haven't personally observed any problems that are fixed by this patch but I also haven't tested this anywhere with a DIV other an 0. AKA: this problem was found simply by code inspection and I have no failing test cases that are fixed by it. Presumably this could fix real bugs for someone out there, though. Fixes: 16a34574c6ca ("mmc: dw_mmc: remove the quirks flags") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
| * mmc: dw_mmc: Add locking to the CTO timerDouglas Anderson2017-10-301-10/+81
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This attempts to instill a bit of paranoia to the code dealing with the CTO timer. It's believed that this will make the CTO timer more robust in the case that we're having very long interrupt latencies. Note that I originally thought that perhaps this patch was being overly paranoid and wasn't really needed, but then while I was running mmc_test on an rk3399 board I saw one instance of the message: dwmmc_rockchip fe320000.dwmmc: Unexpected interrupt latency I had debug prints in the CTO timer code and I found that it was running CMD 13 at the time. ...so even though this patch seems like it might be overly paranoid, maybe it really isn't? Presumably the bad interrupt latency experienced was due to the fact that I had serial console enabled as serial console is typically where I place blame when I see absurdly large interrupt latencies. In this particular case there was an (unrelated) printout to the serial console just before I saw the "Unexpected interrupt latency" printout. ...and actually, I managed to even reproduce the problems by running "iw mlan0 scan > /dev/null" while mmc_test was running. That not only does a bunch of PCIe traffic but it also (on my system) outputs some SELinux log spam. Fixes: 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme") Tested-by: Emil Renner Berthing <kernel@esmil.dk> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
| * mmc: dw_mmc: Fix the CTO timeout calculationDouglas Anderson2017-10-301-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the commit 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme") we tried to calculate the expected hardware command timeout value. Unfortunately that calculation isn't quite correct in all cases. It used "bus_hz" but, as far as I can tell, it's supposed to use the card clock. Let's account for the div value, which is documented as 2x the value stored in the register, or 1 if the register is 0. NOTE: It's not expected that this will actually fix anything important since the 10 ms margin added by the function will pretty much dwarf any calculations. The card clock should be 100 kHz at minimum and: 1000 ms/s * (255 * 2) / 100000 Hz. Gives us 5.1 ms. ...so really the point of this patch is just to make the code more "correct" in case anyone ever tries to remove the 10 ms buffer. Fixes: 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme") Tested-by: Emil Renner Berthing <kernel@esmil.dk> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
| * mmc: dw_mmc: cancel the CTO timer after a voltage switchDouglas Anderson2017-10-301-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When running with the commit 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme") I found this message in the log: Unexpected command timeout, state 7 It turns out that we weren't properly cancelling the new CTO timer in the case that a voltage switch was done. Let's promote the cancel into the dw_mci_cmd_interrupt() function to fix this. Fixes: 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme") Tested-by: Emil Renner Berthing <kernel@esmil.dk> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: dw_mmc: catch all errors when getting regulatorsWolfram Sang2017-10-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Bail out everytime when mmc_regulator_get_supply() returns an errno, not only when probing gets deferred. This is currently a no-op, because this function only returns -EPROBE_DEFER or 0 right now. But if it will throw another error somewhen, it will be for a reason. (This still doesn't change that getting regulators is optional, so 0 can still mean no regulators found). So, let us a) be future proof and b) have driver code which is easier to understand. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: dw_mmc: make const arrays mszs staticColin Ian King2017-10-301-2/+2
|/ | | | | | | | | | | | | | | | Don't populate the const arrays mszs on the stack, instead make them static. Makes the object code smaller by over 310 bytes: Before: text data bss dec hex filename 47527 8528 320 56375 dc37 drivers/mmc/host/dw_mmc.o After: text data bss dec hex filename 47055 8688 320 56063 daff drivers/mmc/host/dw_mmc.o Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: introduce timer for broken command transfer over schemeAddy Ke2017-08-301-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Per the databook of designware mmc controller 2.70a, table 3-2, cmd done interrupt should be fired as soon as the the cmd is sent via cmd line. And the response timeout interrupt should be generated unconditioinally as well if the controller doesn't receive the resp. However that doesn't seem to meet the fact of rockchip specified Soc platforms using dwmmc. We have continuously found the the cmd done or response timeout interrupt missed somehow which took us a long time to understand what was happening. Finally we narrow down the root to the reconstruction of sample circuit for dwmmc IP introduced by rockchip and the buggy design sweeps over all the existing rockchip Socs using dwmmc disastrously. It seems no way to work around this bug without the proper break-out mechanism so that we seek for a parallel pair the same as the handling for missing data response timeout, namely dto timer. Adding this cto timer seems easily to handle this bug but it's hard to restrict the code under the rockchip specified context. So after merging this patch, it sets up the cto timer for all the platforms using dwmmc IP which isn't ideal but at least we don't advertise new quirk here. Fortunately, no obvious performance regression was found by test and the pre-existing similar catch-all timer for sdhci has proved it's an acceptant way to make the code as robust as possible. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196321 Signed-off-by: Addy Ke <addy.ke@rock-chips.com> Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com> [shawn.lin: rewrite the code and the commit msg throughout] Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: move controller reset before driver initliwei2017-08-301-6/+6
| | | | | | | | | | | | | | | | This commit modifies dw_mci_probe(), it moves reset assertion before drv_data->init(host) Some driver needs to access controller registers in its .init() ops. So, in order to make such access safe, we should do controller reset before .init() being called. Signed-off-by: Wei Li <liwei213@huawei.com> Signed-off-by: Guodong Xu <guodong.xu@linaro.org> Signed-off-by: Chen Jun <chenjun14@huawei.com> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: explicitly request exclusive reset controlPhilipp Zabel2017-08-301-1/+1
| | | | | | | | | | | | | | | | | Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: linux-mmc@vger.kernel.org Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: fix the wrong condition check of getting num-slots from DTShawn Lin2017-07-271-1/+1
| | | | | | | | | | | Change to print the information about when the deprecated "num-slots" DT binding is being used, as to avoid confusion when browsing the log: dwmmc_rockchip fe320000.dwmmc: 'num-slots' was deprecated. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Fixes: d30a8f7bdf64 ("mmc: dw_mmc: deprecated the "num-slots" property") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: dw_mmc: remove the unnecessary slot variableJaehoon Chung2017-06-291-8/+5
| | | | | | | | Remove the unnecessary slot variable. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
View Lorry Controller Status