summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/intel/e1000e/ich8lan.c
Commit message (Collapse)AuthorAgeFilesLines
* e1000e: Add support for EEE in Sx statesDavid Ertman2014-07-251-2/+16
| | | | | | | | | | | | | | | | | | On I217 and newer hardware, EEE is enabled in the PHY by the software when link is up and disabled by the hardware when link is lost. To enable EEE in Sx (When both ends of the link support, and are enabled for, EEE and 100Mbps), we need to disable LPLU and configure the PHY to automatically enable EEE when link is up, since there will be no software to complete the task. To configure this in the PHY, the Auto Enable LPI bit in the Low Power Idle GPIO Control register must be set. For normal operation in S0, this bit must be cleared. Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Fix CRC errors with jumbo trafficDavid Ertman2014-07-251-1/+1
| | | | | | | | | Modifying the jumbo frame workaround for 82579, i217 and i218 client parts to increase the gap between the read and write pointers in the Tx FIFO. Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: remove unnecessary break after returnFabian Frederick2014-07-201-1/+0
| | | | | Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: Cleanup parenthesis around return valueDavid Ertman2014-05-271-2/+2
| | | | | | Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Failure to write SHRA turns on PROMISC modeDavid Ertman2014-05-261-8/+49
| | | | | | | | | | | | | | | | | | | | | | | Previously, the check to turn on promiscuous mode only took into account the total number of SHared Receive Address (SHRA) registers and if the request was for a register within that range. It is possible that the Management Engine might have locked a number of SHRA and not allowed a new address to be written to the requested register. Add a function to determine the number of unlocked SHRA registers. Then determine if the number of registers available is sufficient for our needs, if not then return -ENOMEM so that UNICAST PROMISC mode is activated. Since the method by which ME claims SHRA registers is non-deterministic, also add a return value to the function attempting to write an address to a SHRA, and return a -E1000_ERR_CONFIG if the write fails. The error will be passed up the function chain and allow the driver to also set UNICAST PROMISC when this happens. Cc: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2014-05-121-29/+42
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/ethernet/altera/altera_sgdma.c net/netlink/af_netlink.c net/sched/cls_api.c net/sched/sch_api.c The netlink conflict dealt with moving to netlink_capable() and netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations in non-init namespaces. These were simple transformations from netlink_capable to netlink_ns_capable. The Altera driver conflict was simply code removal overlapping some void pointer cast cleanups in net-next. Signed-off-by: David S. Miller <davem@davemloft.net>
| * e1000e: Restrict MDIO Slow Mode workaround to relevant partsDavid Ertman2014-05-051-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It has been determined that the workaround of putting the PHY into MDIO slow mode to access the PHY id is not necessary with Lynx Point and newer parts. The issue that necessitated the workaround has been fixed on the newer hardware. We will maintains, as a last ditch attempt, the conversion to MDIO Slow Mode in the failure branch when attempting to access the PHY id so as to cover all contingencies. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000e: Fix issue with link flap on 82579David Ertman2014-05-051-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several customers have reported a link flap issue on 82579. The symptoms are random and intermittent link losses when 82579 is connected to specific link partners. Issue has been root caused as interoperability problem between 82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake mechanism. To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M Low Power Idle. This solution will cause an increase of power in 100M EEE link. It will cost additional 28mW in this specific mode. Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com> Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000e: Expand workaround for 10Mb HD throughput bugDavid Ertman2014-05-051-4/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance between two 82579 connected via 10Mbit hub", a workaround was put into place to address the overaggressive transmit behavior of 82579 parts when connecting at 10Mbs half-duplex. This same behavior is seen on i217 and i218 parts as well. This patch expands the original workaround to encompass these parts. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
| * e1000e: Workaround for dropped packets in Gig/100 speeds on 82579David Ertman2014-05-051-19/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a workaround for a HW erratum on 82579 devices. Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset specification Update June 2013. Problem: 82579 parts experience packet loss in Gig and 100 speeds when interconnect between PHY and MAC is exiting K1 power saving state. This was previously believed to only affect 1Gig speed, but has been observed at 100Mbs also. Workaround: Disable K1 for 82579 devices at Gig and 100 speeds. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: Cleanup to fix checkpatch missing blank linesDavid Ertman2014-04-231-0/+1
|/ | | | | | | | Fixing "WARNING:SPACING: networking uses a blank line after declarations" Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Fix SHRA register access for 82579David Ertman2014-03-071-1/+1
| | | | | | | | | | | | | | | | | | | | Previous commit c3a0dce35af0 fixed an overrun for the RAR on i218 devices. This commit also attempted to homogenize the RAR/SHRA access for all parts accessed by the e1000e driver. This change introduced an error for assigning MAC addresses to guest OS's for 82579 devices. Only RAR[0] is accessible to the driver for 82579 parts, and additional addresses must be placed into the SHRA[L|H] registers. The rar_entry_count was changed in the previous commit to an inaccurate value that accounted for all RAR and SHRA registers, not just the ones usable by the driver. This patch fixes the count to the correct value and adjusts the e1000_rar_set_pch2lan() function to user the correct index. Cc: John Greene <jogreene@redhat.com> Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Feature Enable PHY Ultra Low Power Mode (ULP)David Ertman2014-03-071-26/+298
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ULP is a power saving feature that reduces the power consumption of the PHY when a cable is not connected. ULP is gated on the following conditions: 1) The hardware must support ULP. Currently this is only I218 devices from Intel 2) ULP is initiated by the driver, so, no driver results in no ULP. 3) ULP's implementation utilizes Runtime Power Management to toggle its execution. ULP is enabled/disabled based on the state of Runtime PM. 4) ULP is not active when wake-on-unicast, multicast or broadcast is active as these features are mutually-exclusive. Since the PHY is in an unavailable state while ULP is active, any access of the PHY registers will fail. This is resolved by utilizing kernel calls that cause the device to exit Runtime PM (e.g. pm_runtime_get_sync) and then, after PHY access is complete, allow the device to resume Runtime PM (e.g. pm_runtime_put_sync). Under certain conditions, toggling the LANPHYPC is necessary to disable ULP mode. Break out existing code to toggle LANPHYPC to a new function to avoid code duplication. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Cc: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Add missing branding strings in ich8lan.cDavid Ertman2014-03-071-0/+8
| | | | | | | | | | Branding strings from recently released and soon to be released hardware configurations that are supported by e1000e. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Cleanup - Update GPL header and CopyrightDavid Ertman2014-03-071-27/+20
| | | | | | | | | | | | | This patch is to update the GPL header by removing the portion that refers to the Free Software Foundation address. Change the copyright date for 2014. Reformat the header comments to conform to kernel networking coding norms Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Fix 82579 sets LPI too early.David Ertman2014-03-071-4/+12
| | | | | | | | | | | | | | Enabling EEE LPI sooner than one second after link up on 82579 causes link issues with some switches. Remove EEE enablement for 82579 parts from the link initialization flow to avoid initializing too early. EEE initialization for 82579 will be done in e1000e_update_phy_task. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Acked-by: Bruce W Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Resolve issues with Management Engine (ME) briefly blocking PHY resetsDavid Ertman2014-03-071-4/+26
| | | | | | | | | | | | | | | | | | | | | On a ME enabled system with the cable out, the driver init flow would generate an erroneous message indicating that resets were being blocked by an active ME session. Cause was ME clearing the semaphore bit to block further PHY resets for up to 50 msec during power-on/cycle. After this interval, ME would re-set the bit and allow PHY resets. To resolve this, change the flow of e1000e_phy_hw_reset_generic() to utilize a delay and retry method. Poll the FWSM register to minimize any extra time added to the flow. If the delay times out at 100ms (checked in 10msec increments), then return the value E1000_BLK_PHY_RESET, as this is the accurate state of the PHY. Attempting to alter just the call to e1000e_phy_hw_reset_generic() in e1000_init_phy_workarounds_pchlan() just caused the problem to move further down the flow. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> Acked-by: Bruce W. Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: fix overrun of PHY RAR arrayDavid Ertman2013-09-131-5/+8
| | | | | | | | | | | | | | | | | | When copying the MAC RAR registers to PHY there is an error in the calculation of the rar_entry_count, which causes a write of unknown/ undefined register space in the MAC to unknown/undefined register space in the PHY. This patch fixes the overrun with writing to the PHY RAR and also fixes the ethtool offline register tests so that the correctly addressed registers have the appropriate bitmasks for R/W and RO bits for affected parts. Shawn Rader gets credit for finding and fixing the register overrun. Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com> CC: Shawn Rader <shawn.t.rader@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: fix I217/I218 PHY initialization flowBruce Allan2013-07-281-33/+50
| | | | | | | | | | The initialization of the PHY on I217/I218, while similar to 82579, must also check to see if the MAC and PHY are in the same mode (PCIe vs. SMBus) otherwise the PHY will be inaccessible by the MAC. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: enable support for new device IDsBruce Allan2013-07-281-2/+6
| | | | | | | | | | | The device IDs 0x15a0 and 0x15a1 are new SKUs that contain the same MAC as I217 and same PHY as I218. The device IDs 0x15a2 and 0x15a3 are the same as existing I218 SKUs. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: Tx hang on I218 when linked at 100Half and slow response at 10MbpsBruce Allan2013-07-281-7/+42
| | | | | | | | | | | | | | Tx hang is an unintended consequence of another workaround that is in the EEPROM for an issue with the firmware at 10Mbps when K1 (a power mode of the MAC-PHY interconnect) is enabled. The issue is resolved by setting appropriate Tx re-transmission timeouts in the PHY and associated K1 entry times in the MAC to allow enough transmissions to occur without triggering a Tx hang. A similar change is needed when linked at 10Mbps to improve latency. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: cleanup whitespaceBruce Allan2013-05-211-31/+31
| | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: add support for LTR on I217/I218Bruce Allan2013-03-281-0/+97
| | | | | | | | | | | | | | | | | Set the Latency Tolerance Reporting (LTR) values for the "PCIe-like" GbE MAC in the Lynx Point PCH based on Rx buffer size and link speed when link is up (which must not exceed the maximum latency supported by the platform), otherwise specify there is no LTR requirement. Unlike true-PCIe devices which set the LTR maximum snoop/no-snoop latencies in the LTR Extended Capability Structure in the PCIe Extended Capability register set, on this device LTR is set by writing the equivalent snoop/no-snoop latencies in the LTRV register in the MAC and set the SEND bit to send an Intel On-chip System Fabric sideband (IOSF-SB) message to the PMC. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: enable EEE by defaultBruce Allan2013-03-281-4/+0
| | | | | | | | | | Now that IEEE802.3az-2010 Energy Efficient Ethernet has been approved as standard (September 2010) and the driver can enable and disable it via ethtool, enable the feature by default on parts which support it. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: EEE capability advertisement not set/disabled as requiredBruce Allan2013-03-281-27/+28
| | | | | | | | | | | | | | | Devices supported by the driver which support EEE (currently 82579, I217 and I218) are advertising EEE capabilities during auto-negotiation even when EEE has been disabled. In addition to not acting as expected, this also caused the EEE status reported by 'ethtool --show-eee' to be wrong when two of these devices are connected back-to-back and EEE is disabled on one. In addition to fixing this issue, the ability for the user to specify which speeds (100 or 1000 full-duplex) to advertise EEE support has been added. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: long access timeouts when I217/I218 MAC and PHY are out of syncBruce Allan2013-03-271-1/+28
| | | | | | | | | | | | | When the MAC and PHY are in two different modes (different power levels and interconnect speeds), it could take a long time before a PHY register access timed out using the existing MAC-PHY interconnect configuration coded into the driver for ICH- and PCH-based LOMs. Introduce an I217/I218- specific .setup_physical_interface operation which does not override the interconnect configuration in the NVM. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: slow performance between two 82579 connected via 10Mbit hubBruce Allan2013-03-271-0/+28
| | | | | | | | | | | | | | | Two 82579 LOMs connected via a 10Mb hub experience extraordinarily low performance. This is because 82579 is excessively aggressive on transmit at 10Mb half-duplex and will not provide sufficient time for the link partner to transmit. When the link partner is also 82579, the result is a lot of collisions (and corresponding re-transmits) that cause the poor performance. To work-around this issue, significantly increase the IPG in the MAC to allow enough gap for the link partner to transmit and reduce the Rx latency in the analog PHY to 0 to reduce the number of collisions. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2013-03-121-1/+70
|\ | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/ethernet/intel/e1000e/netdev.c Minor conflict in e1000e, a line that got fixed in 'net' has been removed in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * e1000e: workaround DMA unit hang on I218Bruce Allan2013-03-051-1/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At 1000Mbps link speed, one of the MAC's internal clocks can be stopped for up to 4us when entering K1 (a power mode of the MAC-PHY interconnect). If the MAC is waiting for completion indications for 2 DMA write requests into Host memory (e.g. descriptor writeback or Rx packet writing) and the indications occur while the clock is stopped, both indications will be missed by the MAC causing the MAC to wait for the completion indications and be unable to generate further DMA write requests. This results in an apparent hardware hang. Work-around the issue by disabling the de-assertion of the clock request when 1000Mbps link is acquired (K1 must be disabled while doing this). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup USLEEP_RANGE checkpatch checksBruce Allan2013-03-081-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | Resolve strict checkpatch USLEEP_RANGE checks by converting delays and sleeps as described in ./Documentation/timers/timers-howto.txt. Three other violations of the text have also been fixed. CHECK:USLEEP_RANGE: usleep_range is preferred over udelay; see Documentation/timers/timers-howto.txt Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup unnecessary line breaksBruce Allan2013-03-081-6/+3
| | | | | | | | | | | | | | | | Cuddle broken lines where appropriate. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup unusually placed commentsBruce Allan2013-03-081-1/+1
| | | | | | | | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup (add/remove) blank lines where appropriateBruce Allan2013-03-081-1/+1
| | | | | | | | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup SPACING checkpatch checksBruce Allan2013-03-081-2/+2
| | | | | | | | | | | | | | | | | | CHECK:SPACING: No space is necessary after a cast CHECK:SPACING: space prohibited before semicolon Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup PARENTHESIS_ALIGNMENT checkpatch checksBruce Allan2013-03-081-19/+21
| | | | | | | | | | | | | | | | CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup SPACING checkpatch errors and warningsBruce Allan2013-03-081-24/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ERROR:SPACING: spaces prohibited around that ':' (ctx:WxV) ERROR:SPACING: need consistent spacing around '-' (ctx:WxV) ERROR:SPACING: space required after that ',' (ctx:VxV) ERROR:SPACING: spaces required around that '=' (ctx:VxV) WARNING:SPACING: missing space after enum definition and some similar spacing issues not reported by checkpatch. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | e1000e: cleanup CODE_INDENT checkpatch errorsBruce Allan2013-03-081-37/+37
|/ | | | | | | | ERROR:CODE_INDENT: code indent should use tabs where possible Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: cleanup checkpatch braces checksBruce Allan2013-02-051-1/+0
| | | | | | | | | | | Resolve the following strict checkpatch checks: CHECK:BRACES: Blank lines aren't necessary after an open brace '{' CHECK:BRACES: Blank lines aren't necessary before a close brace '}' CHECK:BRACES: braces {} should be used on all arms of this statement Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: cosmetic move of #defines and prototypes to the new ich8lan.hBruce Allan2013-02-041-126/+0
| | | | | | | | | | | | | | | Move #defines and function prototypes specific to the ICH/PCH family of devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566, ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new ich8lan.h header file (the convention for Intel wired ethernet drivers is to use the name of the first device in the family for related file and function names). These defines and function prototypes can be used by other files in the driver and moving them to the ICH/PCH-family-specific file makes it clearer to which devices they are applicable. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: use generic IEEE MII definitionsBruce Allan2013-01-311-5/+5
| | | | | | | | | | | | | | | | | For standard IEEE MII-compatible transceivers, the kernel has generic register and bit definitions. Use those instead of redundant local defines. Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000) when it is not necessary (i.e. when it is bitwise OR'ed with another value). Some whitespace issues in the surrounding context of the above changes are also cleaned up. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: resolve -Wunused-parameter compile warningsBruce Allan2013-01-311-2/+2
| | | | | | | | | Remove the unused parameter when possible, otherwise use __always_unused attribute. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: cleanup some whitespace and indentation issuesBruce Allan2013-01-311-2/+2
| | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: correct maximum frame size on 82579Bruce Allan2013-01-271-1/+1
| | | | | | | | The largest jumbo frame supported by the 82579 hardware is 9018. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: cleanup: rename e1000_get_cfg_done()Bruce Allan2013-01-271-1/+1
| | | | | | | | | | In keeping with the e1000e driver function naming convention, the subject function is renamed to indicate it is generic, i.e. it is applicable to more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: cleanup: do not assign a variable a value when not necessaryBruce Allan2013-01-271-5/+5
| | | | | | | | | | Static analysis with cppcheck has shown a few instances of a variable being reassigned a value before the old one has been used. None of these ever require the old value to be used so remove the old values. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: do not ignore variables which get set a valueBruce Allan2013-01-271-2/+3
| | | | | | | | | | | Static analysis with cppcheck has shown a few instances of a variable which is assigned a value that is never used. A number of these are the return status of various driver function calls which should be passed back to the caller of the current function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: cleanup: remove unnecessary function prototypesBruce Allan2013-01-271-4/+1
| | | | | | | | ...and cleanup some whitespace in other prototypes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: fix PHY init workarounds for i217/i218Bruce Allan2013-01-271-0/+9
| | | | | | | | | | | Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it back to power-on defaults. This includes setting it's MAC-PHY messaging mode to use the PCIe-like interconnect, so the MAC must also be set back from SMBus mode to PCIe mode otherwise the PHY can be inaccessible. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: correct maximum frame size on i217/i218Bruce Allan2013-01-271-1/+1
| | | | | | | | The largest jumbo frame supported by the i217 and i218 hardware is 9018. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* e1000e: update copyright dateBruce Allan2013-01-271-1/+1
| | | | | | Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
View Lorry Controller Status